IGAVIEW82GIGAVIEW 821
USER MANUAL |
3 |
GEBRAUCHSANLEITUNG |
9 |
GUIDE UTILISATEUR |
15 |
MODO DE EMPLEO |
21 |
MANUALE D’ISTRUZIONI |
27 |
GEBRUIKSAANWIJZING |
33 |
20448 / 20111212 - GIGAVIEW 821
© ALL RIGHTS RESERVED MARMITEK
2 |
MARMITEK |
SAFETY WARNINGS
• To prevent short circuits, this product should only be used inside and only in dry spaces. Do |
<![if ! IE]> <![endif]>ENGLISH |
||
|
|||
not expose the components to rain or moisture. Do not use the product close to a bath, |
|
||
swimming pool etc. |
|
|
|
• Do not expose the components of your systems to extremely high temperatures or bright |
|
||
light sources. |
|
|
|
• In case of improper usage or if you have altered and repaired the product yourself, all guar- |
|
||
antees expire. Marmitek does not accept responsibility in the case of improper usage of the |
|
||
product or when the product is used for purposes other than specified. Marmitek does not |
|
||
accept responsibility for additional damage other than covered by the legal product responsi- |
|
||
bility. |
|
|
|
• This product is not a toy. Keep out of reach of children. |
|
||
• Do not open the product (battery panel excepted): the device may contain live parts. The |
|
||
product should only be repaired or serviced by a qualified expert. |
|
||
• Keep batteries out of the reach of children. Dispose of batteries as chemical waste. Never |
|
||
use old and new batteries or different types of batteries together. Remove the batteries when |
|
||
you are not using the system for a longer period of time. Check the polarity (+/-) of the bat- |
|
||
teries when inserting them in the product. Wrong positioning can cause an explosion. |
|
||
• Only connect the adapter to the mains after checking whether the mains voltage is the |
|
||
same as the values on the identification tags. Never connect an adapter or power cord when |
|
||
it is damaged. In that case, contact your supplier. |
|
||
1. |
INTRODUCTION |
|
|
Congratulations on purchasing a Marmitek GigaView 821! This allows you to connect a maxi- |
|
||
mum of 2 HD devices and send the HD signal wirelessly to your HDTV or HD projector. |
|
||
Examples of HD devices include: HD DVD players, Blu-ray players, HD set-top boxes, |
|
||
PlayStation3, Xbox 360, etc. The GigaView 821 supports Full HD resolutions up to 1080p and |
|
||
all 3D formats. The inbuilt loop-through function (HDMI out) on the transmitter means that |
|
||
you can watch the same content on the 1st as on the 2nd HDTV or the HD projector (via the |
|
||
receiver). The inbuilt infrared extender function allows you to operate HD equipment using |
|
||
your own remote control even if it is kept in a closed cabinet! |
|
||
Marmitek products are manufactured with the utmost precision and are of top quality. Please |
|
||
read this manual carefully and follow the instructions in order to get the very best from this |
|
||
product. |
|
|
|
2. |
SET CONTENTS |
|
|
1x GigaView 821 Transmitter |
1x IR LED Extender cable |
|
|
1x GigaView 821 Receiver |
2x Energy-saving switch mode Power Supply |
|
|
1x GigaView 821 Remote Control |
2x Plugs + screws |
|
|
1x HDMI cable |
1x User Manual |
|
GIGAVIEW 821 |
3 |
3. INSTALLATION
3.1 GigaView 821 Transmitter connections
HD Media Player
Blu-Ray Player
1.Connect max. 2 HD devices (HDMI OUT) via an HDMI cable to your GV821 Transmitter (HDMI IN).
2.Connect your HDTV or HD Projector (HDMI IN) via an HDMI cable to the GV821 Transmitter (HDMI OUT) in order to use the inbuilt loop-through function.
3.Connect the Power Supply included in delivery to the DC IN on the GV821 Transmitter and to a socket.
3.2 GigaView 821 Receiver connections
DC IN
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
HD Projector |
|
HDTV |
1.Connect your HDTV or HD Projector (HDMI IN) via the HDMI cable supplied to the GV821 Receiver (HDMI OUT).
2.Connect the Power Supply included in delivery to the DC IN on the GV821 Receiver and to a socket.
Note: Use the 2 plugs and 2 screws if you wish to attach the GV821 Receiver to the wall (e.g. behind your HDTV).
4 |
MARMITEK |
3.3 Connect infrared blaster (if necessary)
HDMI
IR Led Extender cable
IR Sensor
Blu-Ray Player
HD Media Player
<![endif]>ENGLISH
Plug the IR LED Extender cable into the IR OUT connector on the GV821 Transmitter. Attach the IR LEDs to the front of your HD devices. This will now send all received infrared commands via the IR Sensor from the GV821 Receiver.
NOTE: The IR Sensor Extender cable supports 36kHz to 56kHz (NEC, RC5, RC6) infrared remote controls. Some devices may not be supported.
4. OPERATION
4.1 Using the GigaView 821 set
1.Place two AAA batteries in the Remote Control.
2.Once the Power Supply has been inserted into the socket, the GV821 will switch itself ON.
•If the GV821 set is in Standby mode (POWER LED is red), press the ON/OFF button on the GV821 Transmitter and Receiver to switch them on. It takes about 80 seconds for the system to start up.
•While warming up, the Power LED will flash blue until the signal connection between the Transmitter and Receiver has been established.
NOTE: the Transmitter and Receiver must be at least 2 metres apart to have a good connection.
GIGAVIEW 821 |
5 |
3. Set the HDTV or HD projector (in HDMI mode) and the HD device that you wish to watch ON.
SOURCE 1 - 2
4.Press the SOURCE button until you see the video images from your device. The time it takes to switch between sources may be about 15-20 seconds.
5.If everything is working correctly, the POWER LED and SOURCE LED will be constantly blue (see table if this is not the case).
6 |
MARMITEK |
4.2 Using the Remote Control
<![if ! IE]><![endif]>ENGLISH
4.3 LOOP-LINK FUNCTION
Activate/deactivate the loop-link function on the GV821 transmitter.
•Activate:
If the GV821 transmitter and receiver are both on, press the Power button once on the receiver. The receiver will go to Stand-by mode and the transmitter will go to loop-link function. The HDTV or projector connected to the receiver will then show the following symbol for 3 seconds.
•Deactivate:
If the GV821 transmitter and receiver are both on, press once on the Power button on the transmitter. Both the transmitter and receiver will go to Stand-by mode and the loop-link function on the transmitter will switch off. The HDTV or projector connected to the receiver will then show the following symbol for 3 seconds.
5. FREQUENTLY ASKED QUESTIONS
No connection
If the GigaView 821 cannot make a stable connection for 80 seconds during start-up, the GV821 receiver is probably outside the range of the GV821 transmitter. Place them closer together (a minimum distance of 2 metres apart) and check whether the connection can be made.
GIGAVIEW 821 |
7 |
No input signal available from chosen source
The GV821 does not recognise an input signal on the selected SOURCE.
•Check whether the correct HDMI source has been selected and whether this is ON.
•Check whether the HDMI cable between the GV821 transmitter and HD device is connected properly.
•Replace the HDMI cable to the HD device.
Video resolution is not supported
The video resolution that is set on your HD device is not recognised by the GV821 transmitter.
•Connect the HD device directly to the HDTV or projector and check whether the set video resolution corresponds to the resolutions that are supported (page 40).
Do you have other questions that have not been resolved by the above information? Please go to www.marmitek.com
6. TECHNICAL DATA
Resolutions |
|
Supported HDTV resolution (HDMI) |
480p, 576p, 720p, 1080i, 1080p |
Supported PC Resolution (max.) |
1600 x 1200 |
Supported 3D formats |
1080p@23.98/24 Hz, 720p@59.94/60/50 Hz |
Supported audio formats (digital) |
up to 6 Mbps AC-3 and DTS |
Supported standards |
HDCP 2.0, EDID/ E-DCC1.1, CEC |
Wireless |
|
Operating frequency |
5.1 ~ 5.6 GHz |
Operating range |
Up to 25 meter LOS (line of sight), up to 12 meter non LOS |
System Latency |
No latency (<1ms) |
Transmitter |
|
HDMI input |
2x HDMI (19-pin female) |
HDMI output |
1x HDMI (19-pin female), built-in HDMI splitter |
IR extender LED |
2.5mm jack |
Dimensions |
192 x 97 x 32mm |
Receiver |
|
HDMI output |
1x HDMI (19-pin female) |
Dimensions |
95 x 95 x 32mm |
Infrared |
|
Supported IR frequency |
36kHz ~ 56kHz |
Power supply |
|
Switch mode Power adaptor |
100-240VAC @ 50-60Hz, 5VDC 3A |
Specifications may be modified without prior notice.
Environmental Information for Customers in the European Union
European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old
equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.
8 |
MARMITEK |
SICHERHEITSHINWEISE
• Um Kurzschluss vorzubeugen, dieses Produkt bitte ausschließlich innerhalb des Hauses und |
|
||
nur in trockenen Räumen nutzen. Setzen Sie die Komponenten nicht Regen oder Feuchtigkeit |
|
||
aus. Nicht neben oder nahe eines Bades, Schwimmbades usw. verwenden. |
|
||
• Setzen Sie die Komponente Ihres Systems nicht extrem hohen Temperaturen oder starken |
|
||
Lichtquellen aus. |
|
|
|
• Bei einer zweckwidrigen Verwendung, selbst angebrachten Veränderungen oder selbst aus- |
<![if ! IE]> <![endif]>DEUTSCH |
||
geführten Reparaturen verfallen alle Garantiebestimmungen. Marmitek übernimmt bei einer |
|||
|
|||
falschen Verwendung des Produkts oder bei einer anderen Verwendung des Produktes als für |
|
||
den vorgesehenen Zweck keinerlei Produkthaftung. Marmitek übernimmt für Folgeschäden |
|
||
keine andere Haftung als die gesetzliche Produkthaftung. |
|
||
• Dieses Produkt ist kein Spielzeug. Außer Reichweite von Kindern halten. |
|
||
• Das Produkt niemals öffnen (ausgen.des Batteriefachs): Das Gerät kann Teile enthalten, |
|
||
worauf lebensgefährliche Stromspannung steht. Überlassen Sie Reparaturen oder Wartung |
|
||
nur Fachleuten. |
|
|
|
• Halten Sie die Batterien außerhalb der Reichweite von Kindern. Liefern Sie die Batterien als |
|
||
chemischen Kleinabfall ein. Verwenden Sie niemals alte und neue oder unterschiedliche Typen |
|
||
von Batterien durcheinander. Wenn Sie das System längere Zeit nicht benutzen, entfernen Sie |
|
||
die Batterien. Achten Sie beim Einlegen der Batterien auf die Polarität (+ / -): Ein falsches |
|
||
Einlegen kann zu Explosionsgefahr führen. |
|
||
• Schließen Sie den Netzadapter erst dann an das Stromnetz an, nachdem Sie überprüft |
|
||
haben, ob die Netzspannung mit dem auf dem Typenschild angegeben Wert übereinstimmt. |
|
||
Schließen Sie niemals einen Netzadapter oder ein Netzkabel an, wenn diese beschädigt sind. |
|
||
In diesem Fall nehmen Sie Kontakt mit Ihrem Lieferanten auf. |
|
||
1. EINFÜHRUNG |
|
|
|
Herzlichen Glückwunsch zum Erwerb des Marmitek GigaView 821! An diesen können Sie |
|
||
maximal 2 HD Geräte anschließen und das HD Signal drahtlos zu Ihrem HDTV oder HD |
|
||
Projektor versenden. Beispiele von HD Geräten sind: HD DVD-Player, Blu-ray Player, HD Settop |
|
||
Boxes, PlayStation3, Xbox 360, usw. Der GigaView 821 unterstützt Full HD Auflösungen bis |
|
||
zu 1080P und alle 3D Auflösungen. Mit der eingebauten Weiterleitungsfunktion (HDMI Out) |
|
||
am Sender können Sie sowohl am Hauptwie am Zweit(HDTV)Fernseher auf dem HD |
|
||
Projektor (über den Empfänger) denselben Inhalt sehen. Die eingebaute Infrarot |
|
||
Verlängerungsfunktion ermöglicht Ihnen, HD Geräte über Ihre eigene Fernbedienung zu bedi- |
|
||
enen, während diese sich in einem verschlossenen Schrank befinden! |
|
||
Marmitek Produkte werden mit großer Sorgfalt hergestellt und sind von hoher Qualität. Lesen |
|
||
Sie diese Anleitung bitte sorgfältig durch und befolgen Sie die Anweisungen, um die |
|
||
Möglichkeiten dieses Produkts optimal nutzen zu können. |
|
||
2. VERPACKUNGSINHALT |
|
||
1x GigaView 821 Sender |
1x IR LED Verlängerungskabel |
|
|
1x GigaView 821 Empfänger |
2x energiesparende, Switch Mode Speisung |
|
|
1x GigaView 821 Fernbedienung |
2x Stecker + Schrauben |
|
|
1x HDMI-Kabel |
1x Gebrauchsanleitung |
|
GIGAVIEW 821 |
9 |
3. INSTALLATION
3.1 GigaView 821 Senderanschlüsse
HD Media Player
Blu-Ray Player
1.Max. 2 HD-Geräte (HDMI AUS) über ein HDMI-Kabel an Ihren GV821 Sender (HDMI IN) anzuschließen.
2.Schließen Sie Ihren HDTV oder HD Projektor (HDMI IN) über ein HDMI Kabel an den GV821 Sender (HDMI OUT) an, um die eingebaute Weiterleitungsfunktion zu nutzen.
3.Schließen Sie den mitgelieferten Speisungsadapter an den DC IN des GV821 Senders und eine Steckdose an.
3.2 GigaView 821 Empfängeranschlüsse
DC IN
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
HD Projector |
|
HDTV |
1.Schließen Sie Ihren HDTV oder HD Projektor (HDMI IN) über das mitgelieferte HDMI-Kabel an den GV821 Empfänger (HDMI OUT) an.
2.Schließen Sie den mitgelieferten Speisungsadapter an den DC IN des GV821 Empfängers und eine Steckdose an.
Achtung: Verwenden Sie die 2 Dübel und 2 Schrauben, wenn Sie den GV821 Empfänger an die Wand montieren möchten (beispielsweise hinter Ihrem HDTV).
10 |
MARMITEK |
3.3 Anschließen de infrarot Blasters (wenn notwendig)
HDMI
IR Led Extender cable
IR Sensor
Blu-Ray Player
HD Media Player
<![endif]>DEUTSCH
Verbinden Sie das IR LED Verlängerungskabel mit dem IR OUT Anschluss des GV821 Senders. Befestigen Sie die IR LED an der Vorderseite Ihrer HD-Geräte. Diese wird nun alle Infrarot Befehle weiterleiten, die vom IR Sensor GV821 Empfänger empfangen werden.
Achtung: Das IR Sensor Verlängerungskabel unterstützt 36kHz bis 56kHz (NEC, RC5, RC6) InfrarotFernbedienungen. Einige Geräte werden möglicherweise nicht unterstützt.
4. ANWENDUNG
4.1 Anwendung des GigaView 821 sets
1.Legen Sie zwei AAA-Batterien in die Fernbedienung ein.
2.Nachdem Sie den Speisungsadapter an die Steckdose angeschlossen haben schaltet das GV821 Set sich EIN.
•Steht das GV821 Set auf Standby (POWER LED ist rot), drücken Sie dann auf die Ein/Austaste des GV821 Senders & Empfängers um diese einzuschalten. Die Inbetriebnahme des Systems nimmt ca. 80 sekunden in Anspruch.
•Während des Aufwärmens wird die Power LED blau blinken, bis die Signalverbindung zwischen dem Sender & Empfänger hergestellt ist.
GIGAVIEW 821 |
11 |
Achtung: Zur Gewährleistung einer optimalen Verbindung stellen Sie Sender und Empfänger mindestens 2 Meter voneinander entfernt auf
3.Schalten Sie den HDTV oder HD-Projektor (im HDMI Modus) und das HD Gerät, dass Sie nutzen möchten EIN.
SOURCE 1 - 2
4.Drücken Sie auf die Source Taste, bis Sie die Videoaufnahmen Ihres Gerätes sehen. Die Schaltzeit zwischen zwei Quellen kann cirka 15 ~ 20 Sekunden betragen.
5.Wenn alles normal funktioniert, wird die POWER LED und SOURCE LED fortwährend blau aufleuchten. (Sehen Sie im anderen Falle nachstehende Tabelle)
12 |
MARMITEK |
4.2 Die Fernbedienung
<![if ! IE]><![endif]>DEUTSCH
4.3 LOOP-THROUGH (DURCHSCHLEIF) FUNKTION
Aktivieren / deaktivieren der Durchschleiffunktion am GV821 Sender.
•Aktivieren
Drücken Sie, nachdem Sie sowohl den GV821 Sender wie den Empfänger eingeschaltet haben, einmal auf die Power-Taste des Empfängers. Der Empfänger wird dann in den Standby Modus und der Sender in die Durchschleiffunktion schalten. Der an den Empfänger angeschlossene HDTV oder Projektor wird 3 Sekunden lang nachfolgendes Symbol anzeigen.
•Deaktivieren:
Drücken Sie, nachdem Sie sowohl den GV821 Sender wie den Empfänger eingeschaltet haben, einmal auf die Power-Taste des Senders. Sender wie auch Empfänger werden beide in den Stand-by Modus schalten und die Durchschleiffunktion am Sender ist ausgeschaltet. Der an den Empfänger angeschlossene HDTV oder Projektor wird 3 Sekunden lang nachfolgendes Symbol anzeigen.
5. HÄUFIG GESTELLTE FRAGEN
Keine Verbindung
Wenn der GigaView 821 nach dem Einschalten innerhalb von 80 Sekunden keine stabile Verbindung herstellen kann, befindet sich der GV821 Empfänger wahrscheinlich außer Reichweite des GV821 Senders. Stellen Sie beide Geräte näher beieinander (mit einer Mindestentfernung von 2 Metern) und kontrollieren Sie, ob sie richtig verbinden.
GIGAVIEW 821 |
13 |
Kein Eingangssignal der gewählten Quelle anwesend
Der GV821 erkennt kein Eingangssignal an der ausgewählten SOURCE (Quelle).
•Überprüfen Sie, ob die richtige HDMI Quelle ausgewählt ist und ob diese EIN geschaltet ist.
•Überprüfen Sie, ob das HDMI Kabel zwischen dem GV821 Sender und HD Gerät richtig angeschlossen ist.
•Ersetzen Sie das HDMI Kabel zum HD Gerät durch ein anderes.
Videoauflösung wird nicht unterstützt
Die an Ihrem HD Gerät eingestellte Videoauflösung wird vom GV821 Sender nicht erkannt.
•Schließen Sie das HD Gerät unmittelbar an den HDTV oder Projektor an und überprüfen Sie, ob die eingestellte Videoauflösung mit den Auflösungen die unterstützt werden (Seite 40) übereinstimmt.
Sie haben noch Fragen, die im Obigen nicht beantwortet wurden? Schauen Sie dann unter www.marmitek.com
6. TECHNISCHE DATEN
Auflösungen |
|
Unterstützte Video-Auflösungen (HDMI) |
480p, 576p, 720p, 1080i, 1080p |
Unterstützte PC Auflösung (max.) |
1600 x 1200 |
Unterstützte 3D Daten |
1080p@23.98/24Hz, 720p@59.94/60/50Hz |
Unterstützte Audio-Einteilungen (digital) |
bis zu 6 Mbps AC-3 und DTS |
Unterstützte Standards (HDMI) |
HDCP 2.0, EDID/ E-DCC1.1, CEC |
Drahtlos |
|
Frequenzbereich 5.1 ~ 5.6 GHz |
|
Maximale Reichweite |
Bis zu 25 Meter LOS (Line Of Sight / Sichtlinie), |
|
bis zu 12 Meter nicht LOS |
Systemlatenz |
Keine Latenz (<1ms) |
Sender |
|
HDMI Eingang |
2 x HDMI (19-Buchsenkontakt) |
HDMI Ausgang |
1 x HDMI (19-Buchsenkontakt), eingebauten HDMI |
|
Splitter |
IR Verlängerung LED |
2,5mm Anschluss |
Maße |
192 x 97 x 32mm |
Empfänger |
|
HDMI Ausgang |
1 x HDMI (19-Buchsenkontakt) |
Maße |
95 x 95 x 32mm |
Infrarot |
|
Unterstützte IR Frequenz |
36kHz ~ 56kHz |
Speisung |
|
Geschaltete Modus Speisung |
100-240VAC @ 50/60Hz, 5VDC 3A |
Spezifikationen können ohne vorhergehende Mitteilung geändert werden.
Umweltinformation für Kunden innerhalb der Europäischen Union
Die Europäische Richtlinie 2002/96/EC verlangt, dass technische Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem Symbol versehen ist nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische und elektronische Geräte über die dafür zuständigen und von der Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei, potentielle negative Folgen für Umwelt
und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das Produkt erworben haben.
14 |
MARMITEK |