Marmitek GIGACAM 4 User Manual

USER MANUAL 3 GEBRAUCHSANLEITUNG 11 GUIDE UTILISATEUR 19 GEBRUIKSAANWIJZING 27

GIGACAM 4tm

GIGACAM 4

Wireless camera with receiver

Thank you for purchasing the Marmitek GIGACAM 4. To fully enjoy your purchase, we advise you to read this manual first. Please observe all information with regard to safe use of this product.

1. SAFETY WARNINGS

• To prevent short circuits, this product (except the outdoor camera) should only be used inside and only in dry spaces. Do not expose the components to rain or humidity. Do not use the product close to a bath, swimming pool etc.

• Only connect the adapter to the mains after checking whether the mains voltage is the same as the values on the identification tags. Never connect an adapter or power cord when it is damaged. In that case, contact your supplier.

• Do not expose the components of your systems to extremely high temperatures or bright light sources.

• Do not open the product: the device contains live parts. The product should only be repaired or serviced by a qualified repairman. In case of improper usage or if you have opened, altered and repaired the product yourself, all guarantees expire. Marmitek does not accept responsibility in case of improper usage of the product or when the product is used for other purposes than specified.

2. USING THE PRODUCT

The GIGACAM 4 is a wireless camera system. The images of the camera are transmitted through walls and ceilings to the receiver, which can be connected to a TV.

3. SET CONTENT

1. Wireless camera

2. Receiver

3. Antenna for camera and receiver

4. Power adapter for camera and receiver

5. Wall bracket

6. Scart cable

7. User manual

3GIGACAM 4

4. GIGACAM 4 WIRELESS CAMERA

1. Camera lens

2. Microphone

3. Channel indicator

4. 2.4 GHZ antenna

5. Cover for the channel switch

6. Connection for the power adapter

7. Wall bracket

8. IR LEDs for night view (only with the optional ‘wireless black/white camera with night view’, see chapter 8)

4.1. HOW TO ACTIVATE THE CAMERA

1. Screw the 2.4 GHz antenna, included in the set, into the back of the camera. Place the antenna in an upright position.

2. Transmitter and receiver have to be set to the same channel. The factory setting of the camera is Camera Channel 1. Normally, you do not need to change this setting. If the camera suffers from interference, you can switch both the camera and receiver to another channel. The switch for the channel setting can be found under the rubber cover on the back of the camera.

4 MARMITEK

Antenna connector

2.4 GHz antenna

3. Connect the power adapter to the camera (6) and plug the adapter into a wall socket.

4. The channel indicator (3) will blink once, twice, three or four times to indicate which channel it is set to (Channel 1 = once, Channel 2 = twice, etc.).

5. RECEIVER

1. ON/OFF switch

2. Power indicator

3. Channel indicator

4. AV output cable with Scart plug

5. 2.4 GHz antenna

6. AV input (Scart)

7. Connection for the power adapter

8. Setting for channels and switch time

5.1. HOW TO ACTIVATE THE RECEIVER

1. Screw the 2.4 GHz antenna, included in the set, into the back of the receiver. Place the antenna in an upright position.

5GIGACAM 4

2. Connect the power adapter to the receiver and plug the adapter into a wall socket.

3. Connect the receiver to your TV as shown below.

You can connect another device (DVD, VCR, satellite receiver, etc.) to the input (6) on your receiver. If you switch off the receiver with button (1), the image of your device will be shown. If you switch on the receiver, the image of your device will disappear and the camera image will be shown.

The factory setting of the receiver is Channel 1. The switch for the channel setting can be found on the back of the receiver (8).

6 MARMITEK

AV output of

your device

Scart cable

Receiver

AV input

AV output. To the Scart input of your TV

AV device

5. Transmitter and receiver have to be set to the same channel. If the camera suffers from interference, you can set it to a different channel.

6. Switch on the receiver by pressing the ON/OFF switch (1).

7. Switch your TV channel to the AV input (number 0 or AV/Scart).

8. You can now watch the camera images on your TV.

9. The channel indicator (3) will blink once, twice, three or four times to indicate which channel it is set to (Channel 1 = once, Channel 2 = twice, etc.).

6. INSTALLING THE CAMERA

The range of the camera and the receiver is dependent on the local situation, but usually somewhere between 15 and 30 m.

The camera is splash-waterproof, according to the IP44 norm. The camera is allowed to get wet, but hard jets of water or heavy rain can enter the camera and cause damage. The camera should be mounted in a sheltered spot (under the eaves, porch etc.).

The signal from the camera can travel through walls and ceilings. The route the signal travels, is not a straight line. Any time the signals go through walls, ceilings and other obstacles, the signal will bend. This can mean that by slightly moving the camera (sometimes just a few centimetres) you can greatly improve the reception. We advise you to first check where you can get optimal range, before fixing the camera in place.

First attach the wall bracket, and then place the camera. Drill a hole through the wall to connect the camera to the power adapter. The plug connecting the camera with the power adapter should preferably be placed on the inside.

THE POWER ADAPTER SHOULD ALWAYS BE PLACED INSIDE.

7GIGACAM 4

Setting for channel 1

7. AUTOMATICALLY SWITCHING BETWEEN CAMERA

IMAGES

You can combine up to 4 cameras with one receiver. The receiver will then automatically switch between the camera images. Every camera should be set to a different channel number.

You can have the receiver switch between images of multiple cameras by setting more than one of the channel switches on the receiver to ON. The switch time is 4 or 8 seconds, depending on the setting of the interval switch (T).

The first 4 switches are for activating channels 1, 2, 3 and 4. Use the T switch to select an interval time of 4 or 8 seconds. Examples: Using one camera

Camera Channel 1 activated. The channel indicator on the receiver will blink once with intervals of 4 seconds.

Camera Channel 3 activated. The channel indicator on the receiver will blink three times with intervals of 8 seconds.

Using several cameras

Camera Channels 1 and 3 are activated alternately. The interval time is 4 seconds. The channel indicator on the receiver will blink once and then three times four seconds later to indicate the active camera channel.

Camera Channels 1, 2 and 3 are activated alternately. The interval time is 8 seconds. The channel indicator on the receiver will blink once, then twice eight seconds later, and eight seconds later it will blink three times to indicate the active camera channel.

8 MARMITEK

8. EXTRA CAMERAS

The cameras below can be purchased separately:

GIGACAM 4 Wireless colour camera

This camera is the same as the camera included in the set.

Art.No. 09621 (European version) Art.No. 09624 (UK version)

GIGACAM 4 wireless black/white camera with night view

The combination of the extremely sensitive CCD camera technique with 9 infrared LEDs makes sure this camera even has some vision in the dark.

Art.No. 09623 (European version) Art.No. 09626 (UK version)

9. FREQUENTLY ASKED QUESTIONS

Does the GIGACAM 4 cause a conflict with my wireless network (WLAN/WIFI/802.11)?

Both systems use the same frequency band (2.4 GHz). You can however choose different channels, both on your GIGACAM 4 system and your WLAN system. This means you can use the systems together most of the times.

Can I look at the images of my camera on more than one location?

Yes, it is best to purchase a second GIGACAM 4 set. The cameras and receivers are mutually compatible.

Any more questions?

Visit www.intellihome.be > FAQ for an up to date list of frequently asked questions for your product.

9GIGACAM 4

10. TECHNICAL DETAILS

GIGACAM 4 Wireless colour camera - Art. Nr. 09621

Camera element: 1/3” CMOS colour Lens: F 1.8/f6.0mm 64° wide-angle lens Video system: PAL Number of pixels: 628(H) x 582 (V) Resolution: 380 screen lines Min. Illumination: 3 lux Microphone: Electret Condenser Transmission power: 10 dBm IP Class: IP44

2.4 GHz frequencies: 2.411 GHz

2.432 GHz

2.453 GHz

2.473 GHz

Power: 12VDC, 500mA

GIGACAM 4 Receiver - Part.No. 27173

Reception sensitivity: -80dBm ~ -30dBm Output level video: 1Vpp @ 75 Ohm Output level audio: 1Vpp @ 600 Ohm

2.4 GHz frequencies: 2.411 GHz

2.432 GHz

2.453 GHz

2.473 GHz Scart output (Scart in to Scart out): CVBS Video, Stereo audio, source select Power: 12VDC, 500mA

Technical details optional GIGACAM 4 wireless black/white camera with night view:

GIGACAM 4 B/W Extreme NightView camera - Art.No. 09623

Camera element: 1/3", CCD black/white Lens: F 2.0/f3.6mm 90° wide-angle lens Video system: CCIR Number of pixels: 500(H) x 582 (V) IR LED range: 5 - 10 m Resolution: 420 screen lines Min. Illumination: 0 lux Microphone: Electret Condenser Transmission power: 10 dBm IP Class: IP44

2.4 GHz frequencies: 2.411 GHz

2.432 GHz

2.453 GHz

2.473 GHz Power: 12VDC, 500mA

10 MARMITEK

GIGACAM 4

Funkkamera mit Empfänger

Herzlichen Glückwunsch zum Erwerb der Marmitek GIGACAM 4. Damit Sie optimal von Ihrer Kamera genießen können, empfehlen wir Ihnen, zunächst die Gebrauchsanleitung sorgfältig durchzulesen. Bitte beachten Sie sämtliche Angaben in Bezug auf eine sichere Nutzung dieses Produktes.

1. SICHERHEITSHINWEISE

• Um Kurzschluss vorzubeugen, dieses Produkt bitte (ausgen. der Außenkamera selbst)

ausschließlich innerhalb des Hauses und nur in trockenen Räumen nutzen. Setzen Sie die Komponenten nicht Regen oder Feuchtigkeit aus. Nicht neben oder nahe eines Bades, Schwimmbades usw. verwenden.

• Schließen Sie den Netzteile erst an das Stromnetz an, nachdem Sie überprüft haben, ob

die Netzspannung mit dem angegebenen Wert auf den Typschildern übereinstimmt. Schließen Sie den Netzteile oder die Netzschnur niemals an, wenn diese beschädigt sind. Nehmen Sie in diesem Falle mit Ihrem Lieferanten Kontakt auf.

• Setzen Sie die Komponente Ihres Systems nicht extrem hohen Temperaturen oder starken

Lichtquellen aus.

• Das Produkt niemals öffnen: Das Gerät enthält Bestandteile mit lebensgefährlicher

Stromspannung. Überlassen Sie Reparaturen oder Wartung nur Fachleuten. Bei unzweckmäßiger Verwendung, selbst angebrachten Veränderungen oder Reparaturen, erlöschen sämtliche Garantieansprüche. Marmitek übernimmt bei inkorrekter Verwendung des Produktes, oder bei zweckentfremdenden Gebrauch, keinerlei Haftung.

2. ANWENDUNG UND BETRIEB

Die GIGACAM 4 ist ein Funkkamera system. Die Bilder der Kamera werden durch Wände und Decken hindurch an den Empfänger, der an einen Fernseher angeschlossen wird, versendet.

3. SET-INHALT

1. Funkkamera

2. Empfänger

3. Antenne für Kamera und Empfänger

4. Netzteile für Kamera und Empfänger

5. Wandhalter

6. Scartkabel

7. Gebrauchsanleitung

11GIGACAM 4

+ 25 hidden pages