
Model MOUNT10 User Guide
VP-10S1 DLP Projector Mount

IMPORTANT SAFETY INSTRUCTIONS
READ BEFORE INSTALLING EQUIPMENT
This product was designed and manufactured to meet strict
quality and safety standards. There are, however, some
installation and operation precautions which you should be
particularly aware of.
1.
Read instructions -
should be read before the product is operate
2.
Retain instructions -
should be retained for future reference.
3.
Heed warnings -
operating instructions should be adhered to.
4.
Follow instructions -
be followed.
5.
Use only the parts provided with the mount, along with any
parts (commercially available) that are specified in this manual.
6.
Do not modify the mount or the parts provided with the mount.
7.
Do not use damaged parts. if any parts become damaged,
contact your dealer.
8.
All bolts and screws must be tightened securely.
9.
Make sure not to block any ventilation openings when installing
the projector.
10.
Special techniques and experience are required when installing
the projector with this mount. Contact your dealer to install the
projector for you.
11.
Once the projector is installed, safety checks should be conducted
on a regular basis.
All the safety and operating instructions
d.
The safety and operating instructions
All warnings on the product and in the
All installation instructions should
MOUNT10
PROJECTOR MOUNT
INSTALLATION INSTRUCTIONS
Step 1
Base Plate Connectors #1 and Projector Mount Ceiling
Plate 1 with
Figure 1
ceiling mounting holes #2.
1
4
2
3 3
Ceiling Wire
Access
4
2
8 5/8"
Plate 1
Base Plate Connectors #1
Projector Mount Ceiling Plate 1
Insert Base Plate connectors #1 into the lateral positioning slots
#
3 as shown in #4 from the underside of Plate 1. The lateral positioning
slots will give you 4 1/2" inches of lateral adjustment for projector
alignment.
14"
2
Warning
The ceiling should be capable of supporting a weight
of at least five (5) times the projector(s) weight.
If it cannot, the ceiling must be reinforced. Proper
installation procedure by qualified personnel as outlined
in the installation instructions must be adhered to.
Failure to do so could result in serious personal injury.
Hardware List
1. Four (4) 3/8 (inch) nuts
2. Four (4) 3/8 (inch) flat washers
3. Two (2) 8 (mm) screws
4. Fourteen (14) 6 (mm) screws
5. Eight (8) 6 (mm) rubber washers
6. Two (2) 8 (mm) rubber washers
Adjustment Ranges and Load Allowances
Horizontal Tilt (yaw) +/- 4 degrees
Vertical Tilt (tilt) +/- 8 degrees
Rotation +/- 15 degrees
Lateral Shift +/- 4
Maximum Load Allowance 450 Lbs.
7. Eight (8) 6 (mm) flat washers
8. One (1) Ceiling Mount #1
9. Two (2) Base Plate Connectors
10. One (1) Horizontal Tilt Plate #2
11. One (1) Horizontal Tilt Plate #3
12. One (1) Projector Plate #4
1/2
inches
Step 2
Horizontal Adjustment Plate 2 (Base Plate Connector
Holes #3).
Figure 2
3
Wire
Access
3
7 5/8"
Plate 2
Base plate connector holes #3 provide 15 degrees of horizontal
adjustment.
Attach horizontal adjustment Plate 2 to projector mount ceiling
Plate 1 using the four (4) 3/8" (inch) nuts and washers provided.
3
10 5/8"
3

MOUNT10 PROJECTOR MOUNT INSTALLATION INSTRUCTIONS continued
Step 2 B
Horizontal Adjustment Plate 2 (Figure 2) attached to
Projector Mount Ceiling Plate 1.
Step 3 B
Horizontal Tilting Plate 3 Attached to Plates 1 and 2.
Figure 3
Figure 5
Wire
Access
Tilting Capability
Plates 1 & 2
Install the combined plates (above) securely to the ceiling
structure in accordance with local commercial building
standards.
Plate 3
The newly combined Plate 3 provides 80 degrees of
horizontal tilt. When positioned, tighten with screws
and washers provided.
Use suitable hardware in adequate quantity and size depending
on the installation requirements. (Please note that Projector
VP-10S1 weighs 90.3 lbs. (41kgs).
Step 3
Step 4
Horizontal Tilting Plate 3 Projector Mounting Plate 4
Tilting Capability
Figure 4
2
2
1
2
2 2
1
Holes for 6mm screws with rubber washer and steel washer
2
Holes for 6mm screws with washer
3
Holes for 8mm screws with rubber washer and steel washer
Plate 3
3
Wire
Access
Indicates Forward
Positioning of Mount
3
2
2
1
2
Attach Horizontal Tilting Plate 3 to the previously combined
plates (already installed on ceiling) using the two (2) 8 (mm)
screws with rubber washers, steel washers and four (4)
6
(mm) screws with washers provided, as indicated in Figure
4. Install two (2) 6 (mm) screws with rubber spacers and
metal washers into the welded metal studs (indicated
Tighten halfway.
#1)
Figure 6
Indicates Forward
Positioning of Mount
111
12 1/4"
1
holes for 6mm screws with rubber washers
1
Plate 4
Invert the projector and place it on a soft and flat surface. Align
the six (6) rubber spacers provided with the six (6) 6 (mm)
mounting holes on the projector and secure with the six (6) 6 (mm)
screws provided.
1
17"
1
continued over

MOUNT10 PROJECTOR MOUNT INSTALLATION INSTRUCTIONS continued
Step 4 B
Projector Mounting Plate 4 (continued)
Projector Mounting Plate 4 connected to Mounting Plate 3
Figure 7
Projector Side
0
8
Tilt
Mount Side
Plate 4
Work in a group of 4 or more to carry the projector and follow
manufacturer's guidelines for relocating as stated in the VP-10S1
owner's manual.
Lift and slide the projector onto the 6 (mm) screws previously
installed in the metal studs of the plate on the ceiling (see arrow
in Figure 7). Tighten the six (mm) screws on both sides of the
mount and install four (4) 6 (mm) screws and washers into the
side of the projector Mounting Plate 4.
0
8
Tilt
Figure 8
Mounts Fully Assembled
Projector Side
Ceiling Side
Sequence of Assembly of Projector Mounting Plates
Plate 4
Step 4
Plate 3
Step 3
Plate 2
Step 2
Plate 1
You can find your nearest authorized distributor or dealer
Printed in Canada
1100 Maplewood Drive
Itasca, IL 60143
Phone: 630 741-0300 Fax: 630 741-0301
on our website at: www.marantz.com
2004