Marantz SR4002, SR5002 User Manual

Model SR4002/SR5002 User Guide
AV Surround Receiver
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suffi cient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG
TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA
LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
NOTE TO CATV SYSTEM INSTALLER:
This reminder is provided to call the CATV (Cable-TV) system installer’s attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifi es that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE:
Changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IMPORTANT SAFETY
INSTRUCTIONS
READ BEFORE OPERATING EQUIPMENT
This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of.
1. Read Instructions – All the safety and operating instructions should be read before the product is operated.
2. Retain Instructions – The safety and operating instructions should be retained for future reference.
3. Heed Warnings – All warnings on the product and in the operating instructions should be adhered to.
4. Follow Instructions – All operating and use instructions should be followed.
5. Cleaning – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6. Attachments – Do not use attachments not recommended by the product manufacturer as they may cause hazards.
7. Water and Moisture – Do not use this product near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.
8. Accessories – Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
9. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
10. Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
11. Power Sources – This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
12. Grounding or Polarization – This product may be equipped with a polarized alternatingcurrent line plug (a plug having one blade wider than the other). This plug will fi t into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fi t, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
AC POLARIZED PLUG
13. Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
14. Protective Attachment Plug – The product is equipped with an attachment plug having overload protection. This is a safety feature. See Instruction Manual for replacement or resetting of protective device. If replacement of the plug is required, be sure the service technician has used a replacement plug specified by the manufacturer that has the same overload protection as the original plug.
15. Outdoor Antenna Grounding – If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of grounding conductors, location of antennadischarge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure 1.
16. Lightning – For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.
17. Power Lines – An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
18. Overloading – Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fi re or electric shock.
19. Object and Liquid Entry – Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fi re or electric shock. Never spill liquid of any kind on the product.
20. Servicing – Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualifi ed service personnel.
21. Damage Requiring Service – Unplug this product from the wall outlet and refer servicing to qualifi ed service personnel under the following conditions:
a. When the power-supply cord or plug is
damaged.
b. If liquid has been spilled, or objects have
fallen into the product.
c. If the product has been exposed to rain or
water.
d. If the product does not operate normally by
following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualifi ed technician to restore the product to its normal operation.
e. If the product has been dropped or damaged
in any way, and
f. When the product exhibits a distinct change
in performance this indicates a need for service.
22. Replacement Parts – When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fi re, electric shock, or other hazards.
23. Safety Check – Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.
24. Wall or Ceiling Mounting – The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
GROUND CLAMP
ELECTRIC SERVICE EQUIPMENT
GROUND CLAMPS
NEC - NATIONAL ELECTRICAL CODE
This Class B digital apparatus complies with Canadian ICES-003.
25. Heat – The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifi ers) that produce heat.
FIGURE 1
ANTENNA LEAD IN WIRE
ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)
GROUNDING CONDUCTORS (NEC SECTION 810-21)
POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)
Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.
DECLARATION OF CONFORMITY
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
U.S. Responsible Party: Marantz America, Inc.
100 Corporate Drive, Mahwah, NJ, 07430, U.S.A. TEL: 630-741-0300
Type of Product: Model:
AV Surround Receiver SR4002/SR5002
AV_060908U1
INTRODUCTION
Thank you for purchasing the Marantz SR4002/SR5002 Surround receiver. This remarkable component has been engineered to provide you with many years of home theater enjoyment. Please take a few minutes to read this manual thoroughly before you connect and operate the SR4002/ SR5002. As there are a number of connection and confi guration options, you are encouraged to discuss your own particular home theater setup with your Marantz A/V specialist dealer.
ACCESSORIES CHECK
Before use, check the below accessories were included in the package.
Remote Controller
T.TONE
SETU
P/
BASS
T.D
ISP
PRESET
DISC+
CH
A NGLE
TUNING
-SE L
SUB
V-O
FF ATT.
TITLE
T
BASS
V
TUNER
AU
D
DIO
V D
TAPE
CD
V
TRE
C
R
BL
E
AUX 1
CDR
D S
S
S Y
ST
AUX 2
E
M
M
D
R
E M
O
R
TE
AMP
C
C
550
O
0S
N TR
R
O L
LE
R
AAA-size batteries × 2
Microphone MC-10
Front AUX Jack Cover
PUSH
PUSH
User Guide
LEARN
SO
U R
l/l/
CE
SEND
SLEE
SET
P
DISPLAY
AIT
OF
P
F
1
P.DIRECT
CS
ON
I I
2
4
S UR
M
E
dts
X/E
-CH RO
UN
S
S
3
T
7
C L
7 .1C
CH
H /C A
T
0
SPKR A/B
M
O
MUTE
UL
SD
TI/
C A
T
M-SPKR
ENTER
MENU
PTY
EXIT
F.DIRECT
D
5
L IP
VIRTUAL
S
INP
STEREO
YNC
U
B
T
/
A
N
6
D
8
T.M
NIG
O
HT
DE
IN
4
9
P .S
A/D
CAN
+1
4
0
HT-EQ
M E
M O
V
OL
LU
M E
AM Loop Antenna
FM Antenna
AC Power Cable
Warranty Card
USA × 1 Canada × 1
TABLE OF CONTENTS
INTRODUCTION ....................................1
ACCESSORIES CHECK ....................................................1
TABLE OF CONTENTS .........................1
FEATURES .............................................2
DESCRIPTION ...................................................................2
BEFORE USE .........................................4
OPERATION OF REMOTE CONTROLLER ......................4
NAMES AND FUNCTIONS ....................5
FRONT PANEL (SR4002) ..................................................5
FRONT PANEL (SR5002) ..................................................5
FL DISPLAY AND INDICATOR ..........................................7
REAR PANEL (SR4002) .....................................................8
REAR PANEL (SR5002) .....................................................8
REMOTE CONTROLLER ................................................10
REMOTE CONTROL OPERATION .....12
GENERAL INFORMATION OF REMOTE CONTROLLER
TO THE UNIT ...................................................................12
CONTROLLING MARANTZ COMPONENTS .................13
BASIC OPERATION .........................................................16
CONNECTIONS ...................................18
SPEAKER PLACEMENT .................................................18
CONNECTING SPEAKERS .............................................18
CONNECTING AUDIO COMPONENTS ..........................19
CONNECTING VIDEO COMPONENTS ..........................20
CONNECTING HDMI COMPONENTS ............................21
ADVANCED CONNECTING ............................................22
CONNECTING THE REMOTE CONTROL JACKS .........22
CONNECTING THE ANTENNA TERMINALS .................23
XM RADIO OVERVIEW (SR5002 ONLY) ........................24
CONNECTING THE XM CONNECT-AND-PLAY ANTENNA CONNECTING FOR THE MULTI ROOM (SR5002 only) 25
CONNECTING OTHER EQUIPMENT .............................26
SETUP ..................................................27
ON SCREEN DISPLAY MENU SYSTEM ........................27
1 INPUT SETUP (ASSIGNABLE DIGITAL INPUT AND
COMPONENT VIDEO INPUT) .........................................28
2 SPEAKER SETUP ........................................................28
3 PREFERENCE .............................................................31
4 SURROUND .................................................................31
5 PL II (PRO LOGIC II) MUSIC PARAMETER ..............32
6 CS II (CIRCLE SURROUND II) PARAMETER ...........32
7 7.1 CH INPUT LEVEL ...................................................32
8 MULTI ROOM (SR5002 only) .......................................32
SIMPLE SETUP ....................................33
...24
BASIC OPERATION (PLAYBACK) ......34
SELECTING AN INPUT SOURCE ...................................34
SELECTING THE SURROUND MODE ...........................34
NIGHT MODE ..................................................................34
ADJUSTING THE MAIN VOLUME ..................................34
ADJUSTING THE TONE (BASS & TREBLE) CONTROL
...34
TEMPORARILY TURNING OFF THE SOUND ..................34
USING THE SLEEP TIMER .............................................34
VIDEO CONVERT ............................................................35
SURROUND MODE .............................36
OTHER FUNCTION ..............................39
DISPLAY MODE ...............................................................39
RECORDING AN ANALOG SOURCE .............................39
SELECTING ANALOG AUDIO INPUT OR DIGITAL AUDIO
INPUT ..............................................................................39
LISTENING THROUGH HEADPHONES
.........................40
DOLBY HEADPHONE MODE .........................................40
ATTENUATION TO ANALOG INPUT SIGNAL ................40
SPEAKER A/B ..................................................................40
7.1 CH INPUT ...................................................................40
AUX2 INPUT .....................................................................41
HT-EQ (HOME THEATER EQUALIZER) .........................41
TV AUTO ON/OFF FUNCTION ........................................41
VIDEO ON/OFF ...............................................................41
LIP.SYNC (SR5002 only) ..................................................41
BASIC OPERATION (TUNER) .............42
LISTENING TO THE TUNER ...........................................42
PRESET MEMORY ..........................................................42
LISTENING TO XM SATELLITE RADIO (SR5002 ONLY)
....44
SEARCH MODE ...............................................................45
PRESET MEMORY ..........................................................47
MULTI ROOM SYSTEM (SR5002 ONLY)
...48
MULTI ROOM PLAYBACK USING THE MULTI ROOM
OUT TERMINALS .............................................................48
MULTI ROOM PLAYBACK USING THE MULTI SPEAKER
TERMINALS .....................................................................48
SURROUND SPEAKER B SYSTEM (SR4002 ONLY)
.49
ANOTHER ROOM PLAYBACK USING THE S
(SURROUND) SPEAKER B TERMINALS .......................49
TROUBLESHOOTING .........................50
HDMI .................................................................................51
XM SATELLITE RADIO ....................................................52
TECHNICAL SPECIFICATIONS ..........53
SETUP CODES .......................................I
ENGLISH
1
ENGLISH
FEATURES
This unit incorporates the latest generation of digital surround sound decoding technology such as Dolby Digital EX, Dolby Digital, DTS-ES (Discrete 6.1 and Matrix 6.1), DTS Neo:6 (Cinema, Music), Dolby Pro­Logic II x (Movie, Music and Game), Circle Surround II (Cinema and Music). In addition, Marantz has focused on the future. By utilizing pre-out jacks, 7.1 direct inputs and a RS­232C communication port (SR5002 only), the unit is tomorrow’s technology, today!
This unit features a fully discrete 7 channel amplifi er section capable of delivering 80 watts (SR4002)/90 watts (SR5002) of high-current amplification, for continuously clean and stable power into each of the 7 channels. It employs a massive EI power transformer in combination with oversized filter capacitors. This design confi guration is capable of a clear and powerful reproduction of the most demanding action movie soundtracks and full range (multichannel) music discs. Through its ability to generate very high output voltages, the unit can easily drive the most demanding speakers with optimum results.
This unit incorporates the most advanced Digital Signal Processing circuitry, along with a Crystal kHz/24 bit D/A converter in each of the 7 channels. Independent power supply circuits are incorporated for the FL display, audio and video sections for maximum separation, clarity and dynamic range. Together with hand-selected customized components, all elements work in harmony to recreate the emotion, exactly as the artist had intended.
This unit is designed and engineered with extensive feedback from custom installation experts, dealers and consumers. It features multi-room/multisource, a RS-232C communication port (SR5002 only), heavy duty speaker binding posts and an extensive array of both analog and digital inputs / outputs. With 6 assignable digital inputs (including Front Aux), 3 assingnable component inputs (SR5002), 5 assignable digital input (SR4002), Super Audio CD Multi Channel (7.1 channel) direct inputs video convert system and OSD output versatility is taken to a stunning new level. Furthermore, the unit can output the OSD information through the Y/C (S­video) and composite video outputs.
®
192
An easy-to-use universal remote controller allows full access to all of the operating functions and can be used for system operation as well.
This unit has Simple Setup function for easy setup. You can setup all speaker settings by just selecting your room size and the number of your speakers with Simple Setup function. You can also setup customized settings just like conventional AV amplifi ers.
• Dolby Digital EX, Dolby Digital , DTS ES (Discrete 6.1, Matrix 6.1, Neo: 6)
• Dolby Headphone 2
• Dolby Pro Logic II x (Movie, Music, Game)
• Circle Surround II (Movie, Music, Mono)
• HDCD decording
• MRAC (Marantz Room Acoustic Calibration) available
• Simple Setup Function
• Improved Station Name Input Method, 50 Presets
• Auto Adjust Function for Speaker Distance Settings (Delay Time)
• LIP.SYNC Funciton (Audio delay)
• 7 × 80 Watts (8 Ohm) (SR4002)/7 × 90 Watts (8 Ohm) (SR5002), Discrete Amplifi ers
• High Power Current Feedback Circuitry
• Massive Energy Power Supply, Huge EI Transformer, Large ELCO’s.
• 192 kHz/24 bit Crystal
• 32 bit Digital Surround Processing Chipsets
• Large Heavy Duty Speaker Terminals for all Channels
• Auto Input Signal Detection
• Front AUX Input (Digital Camera, Portable DVD)
• Video Off Mode
• Set Up Menu via all Video Output (Composite, S­Video and Component video)
• Video convert system
• RS-232C Terminal for System Control (SR5002only)
• Universal remote control
• HDMI (Ver. 1.1)
3 Input/1 Output (SR5002) 2 Input/1 Output (SR4002)
®
DAC for all 8 Channels
DESCRIPTION
Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,003,467 & other U.S. and worldwide patents issued & pending. DTS, DTS Digital Surround, ES, and Neo:6 are registered trademarks and the DTS logos, Symbol and DTS 96/24 are trademarks of DTS, Inc. © 1996-2007 DTS, Inc. All Rights Reserved.
• dts Digital Surround
DTS was introduced in 1994 to provide 5.1 channels of discrete digital audio into home theater systems. DTS brings you premium quality discrete multichannel digital sound to both movies and music. DTS is a multichannel sound system designed to create full range digital sound reproduction. The no compromise DTS digital process sets the standard of quality for cinema sound by delivering an exact copy of the studio master recordings to neighborhood and home theaters. Now, every moviegoer can hear the sound exactly as the moviemaker intended. DTS can be enjoyed in the home for either movies or music on of DVD’s, LD’s, and CD’s.
• dts Neo:6
The advantages of discrete multichannel systems over matrix are well known. But even in homes equipped for discrete multichannel, there remains a need for high-quality matrix decoding. This is because of the large library of matrix surround motion pictures available on disc and on VHS tape; and analog television broadcasts. The typical matrix decoder of today derives a center channel and a mono surround channel from two­channel matrix stereo material. It is better than a simple matrix in that it includes steering logic to improve separation, but because of its mono, band­limited surround it can be disappointing to users accustomed to discrete multichannel.
Neo:6 offers several important improvements as follow,
• Neo:6 provides up to six full-band channels of matrix decoding from stereo matrix material. Users with 6.1 and 5.1 systems will derive six and fi ve separate channels, respectively, corresponding to the standard home-theater speaker layouts.
Neo:6 technology allows various sound elements
• within a channel or channels to be steered separately, and in a way which follows naturally from the original presentation.
Neo:6 offers a music mode to expand stereo nonmatrix recordings into the fi ve- or six-channel layout, in a way which does not diminish the subtlety and integrity of the original stereo recording.
• dts Digital Surround ES
DTS-ES Extended Surround is a new multichannel digital signal format developed by Digital Theater Systems Inc. While offering high compatibility with the conventional DTS Digital Surround format, DTS-ES Extended Surround greatly improves the 360-degree surround impression and space expression thanks to further expanded surround signals. This format has been used professionally in movie theaters since
1999.
In addition to the 5.1 surround channels (FL, FR, C, SL, SR and LFE), DTS-ES Extended Surround also offers the SB (Surround Back) channel for surround playback with a total of 6.1 channels. DTS-ES Extended Surround includes two signal formats with different surround signal recording methods, as DTS­ES Discrete 6.1 and DTS-ES Matrix 6.1.
• dts Digital Surround 96/24
The stereo CD is a 16-bit medium with sampling at
44.1 kHz. Professional audio has been 20- or 24-
bit for some time, and there is increasing interest in higher sampling rates both for recording and for delivery into the home. Greater bit depths provide extended dynamic range. Higher sampling rates allow wider frequency response and the use of anti­alias and reconstruction fi lters with more favorable aural characteristics.
DTS 96/24 allows for 5.1channel sound tracks to be encoded at a rate of 96kHz/24bits on DVD-Video titles. When DVD-video appeared, it became possible to deliver 24-bit, 96 kHz audio into the home, but only in two channels, and with serious limitations on picture. This capability has had little use. DVD-audio allows 96/24 in six channels, but a new player is needed, and only analog outputs are provided, necessitating the use of the D/A converters and analog electronics provided in the player.
DTS 96/24 offers the following:
1. Sound quality transparent to the original 96/24 master.
2
Full backward compatibility with all existing
2. decoders. (Existing decoders will output a 48 kHz signal)
3. No new player required: DTS 96/24 can be carried on DVD-video, or in the video zone of DVD-audio, accessible to all DVD players.
4. 96/24 5.1-channel sound with full-quality full­motion video, for music programs and motion picture soundtracks on DVD-video.
Dolby Digital identifi es the use of Dolby Digital audio coding for such consumer formats as DVD and DTV. As with fi lm sound, Dolby Digital can provide up to fi ve full-range channels for left, center, and right screen channels, independent left and right surround channels, and a sixth (“.1”) channel for low-frequency effects.
Dolby Surround Pro Logic II is an improved matrix decoding technology that provides better spatiality and directionality on Dolby Surround program material; provides a convincing three-dimensional soundfi eld on conventional stereo music recordings; and is ideally suited to bring the surround experience to automotive sound. While conventional surround programming is fully compatible with Dolby Surround Pro Logic II decoders, soundtracks will be able to be encoded specifi cally to take full advantage of Pro Logic II playback, including separate left and right surround channels. (Such material is also compatible with conventional Pro Logic decoders.)
Dolby Digital EX creates six full-bandwidth output channels from 5.1-channel sources. This is done using a matrix decoder that derives three surround channels from the two in the original recording. For best results, Dolby Digital EX should be used with movies soundtracks recorded with Dolby Digital Surround EX.
About Dolby Pro Logic IIx
Dolby Pro Logic IIx technology delivers a natural and immersing 7.1-channel listening experience to the home theater environment. A product of Dolby’s expertise in surround sound and matrix decoding technologies, Dolby Pro Logic IIx is a complete surround sound solution that maximizes the entertainment experience from stereo as well as
5.1-channel encoded sources.
Dolby Pro Logic IIx is fully compatible with Dolby Surround Pro Logic technology and can optimally decode the thousands of commercially available Dolby Surround encoded video cassettes and television programs with enhanced depth and spatiality. It can also process any high-quality stereo or Advanced Resolution 5.1-channel music content into a seamless 6.1- or 7.1-channel listening experience.
The Dolby Headphone technology provides a surround sound listening experience over headphones. When listening to multichannel content such as DVD movies over headphones, the listening experience is fundamentally different than listening to speakers. Since the headphone speaker drivers are covering the pinna of the ear, the listening experience differs greatly from traditional speaker playback. Dolby utilizes patented headphone perspective curves to solve this problem and provides a non-fatiguing, immersive, home theater listening experience. Dolby Headphone also delivers exceptional 3D audio from stereo material.
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories.
Circle Surround II (CS-II ) is a powerful and versatile multichannel technology. CS-II is designed to enable up to 6.1 multichannel surround sound playback from mono, stereo, CS encoded sources and other matrix encoded sources. In all cases the decoder extends it into 6 channels of surround audio and a LFE/subwoofer signal. The CS-II decoder creates a listening environment that places the listener “inside” music performances and dramatically improves both hi-fi audio conventional surround-encoded video material. CS-II provides composite stereo rear channels to greatly improve separation and image positioning – adding a heightened sense of realism to both audio and A/V productions.
CS-II is packed with other useful feature like dialog clarity (SRS Dialog) for movies and cinema-like bass enrichment (TruBass). CS-II can enable the dialog to become clearer and more discernable in movies and it enables the bass frequencies contained in the original programming to more closely achieve low frequencies – overcoming the low frequency limitations of the speakers by full octave.
Circle Surround II, Dialog Clarity, TruBass, SRS and
symbol are trademarks of SRS Labs, Inc. Circle Surround II, Dialog Clarity and TruBass technology are incorporated under license from SRS Labs, Inc.
HDCD® (High Defi nition Compatible Digital ®) is a patented process for delivering on Compact Disc the full richness and details of the original microphone feed. HDCD encoded CDs sound better because they are encoded with 20-bits of real musical information as compared to 16-bits for all other CDs. HDCD overcomes the limitation of the 16-bit CD format by using a sophisticated system to encode the additional four bits onto the CD while remaining completely compatible with the CD format. When listening to HDCD recordings, you hear more dynamic range, a focused 3-D sound stage, and extremely natural vocal and musical timbre. With HDCD, you get the body, depth and emotion of the original performance not a fl at, digital imitation.
HDCD system manufactured under license from Microsoft. This product is covered by one or more of the following: In the United States 5,479,168 5,638,074 5,640,161 5,808,574 5,838,274 5,854,600 5,864,311 5,872,531 and in Australia 669,114 with other patents pending.
HDMI, the and High-Defi nition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
XM Satellite Radio Ready
ENGLISH
The XM name and related logos are registered trademarks of XM Satellite Radio Inc.
3
ENGLISH
BEFORE USE
This section must be read before any connection is made to the mains supply.
EQUIPMENT MAINS WORKING SETTING
Your Marantz product has been prepared to comply with the household power and safety requirements that exist in your area. SR4002/SR5002 can be powered by 120V AC only.
COPYRIGHT
Recording and playback of any material may require consent. For further information refer to the following:
— Copyright Act 1956 — Dramatic and Musical Performers Act 1958 — Performers Protection Acts 1963 and 1972 — Any subsequent statutory enactments and
orders
DO NOT LOCATE IN THE FOLLOWING PLACES
To ensure long-lasting use, do not locate the unit where:
• Exposed to direct sunlight.
• Near to sources of heat such as heaters.
• Highly humid or poorly ventilated.
• Dusty.
• Subjected to mechanical vibrations.
• On wobbly, inclined or otherwise unstable surfaces
• Radiated heat is blocked such as in cramped audio racks.
To ensure proper heat radiation, ensure the below clearance from walls and other equipment.
8 ins. (
0.2 m
)
AV SURROUND RECEIVER SR5002
0.2 m
INPUT SELECTORINPUT SELECTOR
)
SIMPLESIMPLE
PUREPURE
SURROUNDSURROUND
MULTI
SETUPSETUP
DIRECTDIRECT
MODEMODE
MULTI
SPEAKER
STANDBY
AUTOAUTO
HT-EQHT-EQ
MENUMENU
PHONES
POWER ON/STANDBY
SETUP MIC
VOLUMEVOLUME
8 ins. (
UPUP
DOWNDOWN
MEMORYMEMORY
DISPLAYDISPLAY
CLEARCLEAR
ATTATT
MUTEMUTE
ENTERENTER
T-MODET-MODE
EXITEXIT
BAND
BAND
AUX 1 INPUTAUX 1 INPUT
DIGITALDIGITAL
RRLLVIDEOVIDEO
S-VIDEOS-VIDEO
AUDIOAUDIO
8 ins. (
0.2 m
0.2 m
KEEP OBJECTS OFF
Keep objects off the unit. Blocking the vent can result in accident and damage.
DO NOT TOUCH HOT SPOTS DURING AND IMMEDIATELY AFTER USE
During and immediately after use, the unit is hot in areas other than the controls and rear panel connection jacks. Do not touch hot spots and especially the top panel. Contact with hot areas can cause burns.
LOADING BATTERIES
Before using the remote controller for the fi rst time, load the batteries in the remote controller. The batteries provided are used to verify the operations of the remote controller only.
1. Remove the battery cover.
CAUTIONS ON BATTERIES
• Use “AAA” type batteries in this remote controller.
• We recommend that you use alkali batteries.
• If the remote controller does not operate from close to the unit, replace the batteries with new ones, even if less then a year has passed.
• The included battery is only for verifying operation. Replace it with a new battery as soon as possible.
• When inserting the batteries, be careful to do so in the proper direction, following the + and - marks in the remote controller’s battery compartment.
• To prevent damage or battery fl uid leakage:
- Do not use a new battery with an old one.
OPERATION OF REMOTE CONTROLLER
REMOTE CONTROL
Operate the remote controller within a distance of approx. 5m from the infrared receptor window on the front of the unit.
2. Load the two new size “AAA” batteries inside
the battery compartment while taking care to align their polarities correctly with the polarity markings ( with ( and with ).
- Do not use two different types of batteries.
- Do not short-circuit, disassemble, heat or
dispose of batteries in fl ames.
• Remove the batteries when not planning to use the remote controller for a long period of time.
• If the batteries should leak, carefully wipe off the fl uid from the inside of the battery compartment, then insert new batteries.
• When disposing of used batteries, please comply with governmental regulations or environmental public instruction’s rules that apply in your country or area.
Approx. 5 m
S YS TE
M RE
M O
R
T
C
E
5
C
5
O 0 0
N S
TR R
OL L E
R
IN P U T S E
A
L
V
E
S
C
U
T
RR
O R
O U
ND R
E CE IV
ER S R5
00 2
M
UL TI
S
T A N D B Y
P OW
M
E
. S
R O
PE
N/
A
OFF
KE R B
SE TU
P M IC
PH O
NES
60°
Remote controller
S U RR
O
M
U
O
ND DE
PU RE D IR E CT
S IM P
A
SETUP LE
UT
O
HT­E Q
M
V O
EN
L U
U
M
E D I S P
L A Y
ENTER
M EM
OR
D
Y
O W N
CLEAR
EXIT
B AN
D
T-M OD
E
M UTE
D I G IT
A L
7 .
1 C H I N P
S
U
­V I D
E O
A
U
X
V
1
I
D
I
E
N O
P U T
L A U D I O
SR4002/SR5002
U P
T
R
3. Close the battery cover until it clicks shut.
Caution:
• Do not allow direct sunlight, an inverter fl uorescent light or other strong source of light to shine onto the player’s infrared receptor window. Otherwise, the operation of the remote controller may be disabled.
• Bear in mind that operating the remote controller may cause other devices operated by infrared rays to be operated by mistake.
)8 ins. (
• The remote controller cannot be operated if the space between the controller and the player’s infrared receptor window is obstructed.
• Do not place any objects on top of the remote controller.
)
Doing so may cause one or more buttons to be
held down which will cause the batteries to run down.
4
NAMES AND FUNCTIONS
!
@
!
@
@
!
!
@
!
@
!
@
FRONT PANEL (SR4002)
qw ui !4o!0 !1y!3!2rte
AV SURROUND RECEIVER SR4002
INPUT SELECTOR
7.1 CH INPUT
STANDBY
POWER ON/STANDBY
S.SPEAKER B
PHONESSETUP MIC
DISP MULTI AUTO TUNED ST V – OFF NIGHT PEAK ANALOG
SURR
AUTO
SLEEP
SIMPLE
PURE
SURROUND
MODE
AUTO
SETUP
DIRECT
HT-EQ
MENU
DIRECT DISC 6.1 MT X 6.1 SPKR B EQ
ATT
DIGITAL
DISPLAY
ENTER
EXIT
q POWER switch and STANDBY
indicator
u SURROUND MODE button
Press this button to select the surround mode.
When this switch is pressed once, the unit turns ON and the display illuminates. When pressed again, the unit turns OFF and the STANDBY indicator will be illuminated.
i PURE DIRECT button and
indicator
ENGLISH
When this button is pressed once, “SOURCE DIRECT
w MULTI (Multi Room) button
(SR5002 only)
VOLUME
SURROUND
DIGITAL
LCR
LFE
PCM
SL S SR
MEMORY
DOWN
CLEAR
T-MODE
BAND
MUTE
AUX 1 INPUT
DIGITAL
S-VIDEO
UP
ATT
RLVIDEO
AUDIO
Press this button to activate the Multiroom system. “MULTI” indicator will be illuminated in the display.
w 7.1CH INPUT button (SR4002 only)
Press this button to select the output of an external multichannel player.
e INPUT SELECTOR knob
(AUDIO/ VIDEO)
This knob is used to select the input sources. (See page 33)
appears on the FL display. If pressed again, “PURE DIRECT” appears. After 2 seconds, the FL display indication goes out. In the source/pure direct mode, the tone control circuitry and bass management are bypassed.
Notes:
• The surround mode is automatically switched to AUTO when the pure direct/source direct function is turned on.
• Additionally, speaker configurations are fixed automatically as follows.
Front SPKR = LARGE Center SPKR = LARGE Surround SPKR = LARGE Surround Back SPKR = LARGE Sub woofer = YES
4
FRONT PANEL (SR5002)
qw ui !4o!0 !1y!3!2rte
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
MULTI
SETUP MIC
SPEAKER
PHONES
MULTI
STANDBY
POWER ON/STANDBY
4
DISP MULTI AUTO TUNED ST V – OFF NIGHT PEAK ANALOG
SURR
SLEEP
AUTO
SIMPLE
PURE
SURROUND
MODE
AUTO
SETUP
DIRECT
HT-EQ
MENU
0
1@2@3
DIRECT DISC 6.1 MT X 6.1 SPKR B EQ
ENTER
0
1@2@3
7!8!9
6
5
r M.(Multi Room) SPEAKER button
(SR5002 only)
Press this button to activate the Multiroom Speaker system. “MULTI” indicator will be illuminated in the display.
(See page 44)
r S.(Surround) SPEAKER B button
(SR4002 only)
Press this button to activate the Surround Speaker B
o SIMPLE SETUP button
Press this button to enter the simple setup mode. You can setup the speaker conditions (speaker sizes, number of speakers, speaker delay times) quickly by pressing the cursor buttons.
!0 DISPLAY button
Press this button to change the FL display mode. (See page 38)
system . “SPKR B” indicator will be illuminated in the
VOLUME
SURROUND
ATT
DIGITAL
DIGITAL
LCR
LFE
PCM
DISPLAY
SL S SR
MEMORY
CLEAR
EXIT
T-MODE
BAND
DOWN
MUTE
AUX 1 INPUT
DIGITAL
S-VIDEO
7!8!9
6
UP
ATT
RLVIDEO
AUDIO
5
display.
(See page 45)
t
HEADPHONE jack for stereo headphones
This jack may be used to listen to the unit’s output through a pair of headphones. Be certain that the headphones have a standard 1 / 4” stereo phono plug.
y INFRARED receiving sensor
window
This window receives infrared signals for the remote control.
!1 MEMORY button
Press this button to enter the tuner preset memory numbers or station names. (See page 41)
!2 CLEAR button
Press this button to cancel the station-memory setting mode or preset scan tuning. (See page 42)
!3 VOLUME control knob
This knob is used to adjust the overall sound level. Turning the control clockwise increases the sound level. (See page 33)
5
ENGLISH
!4 ATT (Attenuate) button
Press this button to reduce the analog audio signal input level by about half. “ATT” indicator will be illuminated in the display. (See page 39)
!5 AUX1 INPUT jacks
These auxiliary video/audio input jacks accept the connections of a camcorder, portable DVD, game etc. When not using these jacks, protect with the included jack covers.
How to Attach the Front AUX Jack Cover
B
A
N
D
T-MODE
M
DIGIT
PU
P
US
S
H
H
Front AUX Jack Cover
U T
E
AL
UP
7.1CH
INPUT
S
-V ID
E
O
A
U
X
V
1
ID
IN
E
O
P
U
T
L
A
U D
IO
R
!6 MUTE button
Press this button to mute the output to the speakers. Press it again to return to the previous volume level.
@1 MENU button
Press this button to enter the SETUP MAIN MANU.
@2 HT-EQ button
Press this button to turn on or off HT(Home Theater)­EQ mode. This mode compensates for the audio portion of a movie sounding “bright”. “EQ” indicator will be illuminated in the display. (See page 40)
@3 AUTO (Auto surround) button
Press this button to select the AUTO mode from the surround modes. When this mode is selected, the unit determines the surround mode corresponding to a digital input signal automatically.
@4 SETUP MIC jack
Automatically measure speaker characteristics using the included microphone (MC-10). (See page 29)
!7 T-MODE button
Press this button to select the auto stereo mode or mono mode when the FM band is selected. “AUTO” indicator will be illuminated in the display. (See page 41)
!8 BAND button
Press this button to switch between FM and AM in the TUNER mode.
!9 EXIT button
Press this button to exit from the SETUP MAIN MENU.
@0 Cursor (1, 2, 3, 4) / ENTER button
Press these buttons to operate the SETUP MAIN MENU and TUNER function.
6
FL DISPLAY AND INDICATOR
¡
¡
¡
¡
s
a
DISP MULTI AUTO TUNED ST V – OFF NIGHT PEAK ANALOG
AUTO
SURR
SLEEP
g
DIRECT DISC 6.1 MT X 6.1 SPKR B EQ
hk¡0 ¡2 ¡4f
jl¡1
™0
9
a DISP (Display Off) indicator
This indicator is illuminated when this unit is in the display off mode.
s SLEEP timer indicator
This indicator is illuminated when the sleep timer function in the main-room is in use.
j V (video)-OFF mode indicator
This indicator is illuminated when the Video-OFF function is active.
k NIGHT mode indicator
This indicator is illuminated when this unit is in the Night mode, which reduces the dynamic range of digital program material at low volume levels.
d Multi-room system indicator
This indicator is illuminated when the multi-room system is active.
f AUTO SURR (Auto Surround
mode) indicator
This indicator is illuminated to show that the AUTO SURROUND mode is in use.
g TUNER’s indicators
AUTO : This indicator illuminates when the
tuner’s Auto mode is in use.
TUNED : This indicator illuminates when the
tuner receives a suffi ciently strong radio signal.
ST(Stereo) : This indicator illuminates when an
FM station is being tuned into stereo condition.
h DTS-ES mode indicators
(DISC6.1, MTX6.1)
These indicators will illuminate to show the DTS-ES decoding mode (Discrete 6.1 or Matrix 6.1).
l SPKR (speaker) AB indicator
This indicator is illuminated when the M (Multiroom) speaker B system is active. (SR4002 only) It displays the speaker system in use (A or B). When the speakers are not in use, both lights (A and B) will be turned off. (SR5002 only)
¡0 PEAK indicator
This indicator is a monitor for an analog audio input signal. If the selected analog audio input signal is greater than the capable level of internal processing, this will illuminate. If this happens, you should press the ATT button.
¡1 EQ mode indicator
This indicator is illuminated when the HT-EQ function is active.
¡2 ATT (Attenuation) indicator
This indicator is illuminated when the attenuation function is active.
ATT
¡3
DIGITAL
PCM
8
¡5d
SURROUND
DIGITAL
C
L
LFE
SL S SR
7
¡3 DIGITAL Input Indicator
This indicator is illuminated when a digital input has been selected.
¡4 ANALOG input indicator
This indicator is illuminated when an analog input source has been selected.
R
¡8 HDCD indicator
This indicator is illuminated when the HDCD signal is decoded from digital input signal.
¡9 Main Information Display
This display shows messages relating to the status, input source, surround mode, tuner, volume level or other aspects of unit’s operation.
ENGLISH
¡5 SIGNAL FORMAT indicators
2 DIGITAL This indicator is illuminated when a Dolby Digital
6
signal is input.
EX
This indicator is illuminated when a Dolby Digital EX signal is input.
dts
This indicator is illuminated when a DTS signal is input.
ES
This indicator is illuminated when a DTS ES signal is input.
96/24
This indicator is illuminated when a DTS 96/24 signal is input.
PCM
This indicator is illuminated when the input signal is PCM (pulse code modulation).
2 SURROUND
This indicator is illuminated when a Dolby Surround signal is input.
™0 DIRECT (Puredirect) indicator
This indicator is illuminated when this unit is in the SOURCE DIRECT or PURE DIRECT mode.
¡6 HDMI indicator
This indicator is illuminated when input terminal of the HDMI component is connected to the unit.
¡7 ENCODED CHANNEL STATUS
indicators
These indicators display the channels that are encoded with a digital input signal. If the digital input signal is Dolby Digital 5.1ch or DTS 5.1ch, “L”, “C”, “R”, “SL”, “SR” and “LFE” will be illuminated. If the digital input signal is 2 channel PCM-audio, “L” and “R” will be illuminated. If the digital input signal is Dolby Digital 5.1ch signal with Surround EX fl ag or DTS-ES, “L”, “C”, “R”, “SL”, S” , “SR” and “LFE” will be illuminated.
7
ENGLISH
SR
C
SBR
SL
SBL
L
R
SPEAKER SYSTEMS : 6-8 OHMS
CENTER
R
FRONT
SURROUND BACK
S. SPEAKER B
SURROUND
L
L
R
IN
1
3
OPT
DIGITAL OUT
(
AUX2
)
7.1CH INPUT
SBL
SBR
R
L
FM
(
75
)
GNDAMAM
C
R
/
P
R
C
B
/
P
B
Y
ANTENNA
DIGITAL IN
OUTININ
CD/CDR
OUTININ
TAPE
VCR
DVDTVTV
AUDIO
OUT
AC OUTLETS
120V 60Hz
SWITCHED
1.25A 150W
C
R
/
P
R
C
B
/
P
B
Y
DSS
DVD
VCR IN
VCR OUT
MONITOR OUT
MONITOR
OUT
INPUT
1
INPUT
2
S-VIDEO
VIDEO
IN
FLASHER
MODEL NO. SR4002
PRE OUT
AC IN
INPUT
3
INPUT 3
OUTPUT
INPUT 2
INPUT 1
HDMI Ver 1.1
COMPONENT
VIDEO
DSS
OUT
REMOTE CONT.
SR
C
SBR
MULTI.
OUT
SL
SBL
L
R
R
XM
L
L
L
R
IN
OUT
REMOTE CONT.
OPT
DIGITAL OUT
(
AUX2
)
7.1CH INPUT
SBL
SBR
RS-232C
SPEAKER C
OFFONON
R
L
FM
(
75
)
GNDAMAM
C
R
/
P
R
C
B
/
P
B
Y
C
R
/
P
R
C
B
/
P
B
Y
1
ANTENNA
DIGITAL IN
OUTININ
CD/CDR
OUTININ
TAPE
VCR
DVDTVTV
AUDIO
DSS
OUT
C
R
/
P
R
C
B
/
P
B
Y
DSS
DVD
VCR IN
VCR OUT
MONITOR OUT
MONITOR
OUT 2
INPUT
1
INPUT
2
S-VIDEO
VIDEO
AC IN
MODEL NO. SR5002
FLASHER
IN
PRE OUT
AC OUTLETS
120V 60Hz
SWITCHED
1.25A 150W
CENTER
SURROUND
SURROUND BACK
SPEAKER C/MULTI SPEAKER
FRONT A OR B.CENTER.
FRONT A
+
B : 8 OHMS
SPEAKER SYSTEMS
FRONT B B
FRONT A A
SURR.SURR BACK : 6-8 OHMS
1
4
DC
TRIGGER
3
INPUT
3
INPUT 3
OUTPUT
INPUT 2
INPUT 1
HDMI Ver 1.1
COMPONENT
VIDEO
REAR PANEL (SR4002)
w
(
)
FM
75
ANTENNA
LLSLSLCCSBL
L
R
RRSRSRSWSWSBR
(
)
AUX2
7.1CH INPUT
SL
L
RRSR
PRE OUT
y
!1 q r !6
VIDEO
S-VIDEO
GND
C
SWSWSBR
!0
TVTVDVD
VCR IN
ININOUT
DVD
SBL
!4
VCR
VCR OUT
R
FRONT
t
INPUT
INPUT
DSS
MONITOR OUT
DSS
AUDIO
L
SURROUND BACK
S. SPEAKER B
SPEAKER SYSTEMS : 6-8 OHMS
1
2
C
R
/
P
R
C
B
/
P
B
Y
OUT
CD/CDR
TAPE
R
LLR
SURROUND
C
R
/
P
R
C
B
/
P
B
Y
443
221
OUT
DIGITAL IN
L
CENTER
o
INPUT
3
MONITOR
OUT
!5
COMPONENT
VIDEO
DIGITAL OUT
OPT
!3
REMOTE CONT.
SWITCHED
1.25A 150W
AC OUTLETS
120V 60Hz
i
OUT
REAR PANEL (SR5002)
!1 q r !6
e!9
w
(
)
FM
75
GND
ANTENNA
LLSLSLCCSBL
L
R
RRSRSRSWSWSBR
(
)
AUX2
7.1CH INPUT
RS-232C
SL
L
RRSR
PRE OUT
y
SPEAKER C
SWSWSBR
!0
OFF
C
SBL
!2
VIDEO
S-VIDEO
MULTI.
OUT
FRONT A OR B.CENTER.
FRONT A
TVTVDVD
RRL
FRONT
+
B : 8 OHMS
t
INPUT
1
INPUT
2
DSS
VCR IN
VCR OUT
MONITOR OUT
ININOUT
VCR
DVD
FRONT
DSS
AUDIO
R
LLR
SURROUND BACK
SPEAKER C/MULTI SPEAKER
SURR.SURR BACK : 6-8 OHMS
o
TAPE
1
Y
C
R
/
P
R
C
B
/
P
B
Y
OUT
OUT
CD/CDR
R
L
L
SURROUND
SPEAKER SYSTEMS
C
B
CENTER
/
P
B
554
221
DIGITAL IN
C
R
/
P
R
!4
COMPONENT
INPUT
VIDEO
3
C
C
B
/
P
B
Y
3
OPT
REMOTE CONT.
DIGITAL OUT
SWITCHED
1.25A 150W
AC OUTLETS
120V 60Hz
!5
q
VIDEO IN/OUT (TV, DVD, VCR, DSS)
These are the video inputs and outputs. There are 4 video inputs and 2 video outputs and each one includes both composite video and S-video
HDMI Ver 1.1
INPUT 3
INPUT 2
INPUT 1
IN
OUTPUT
confi gurations. Connect VCRs, DVD players, and other video components to the video inputs. The 2 video output channels can be used to be connected to video tape recorders for making recordings.
FLASHER
IN
w FM antenna terminal (75 ohms)
AC IN
MODEL NO. SR4002
u
Connect an external FM antenna with a coaxial cable, or a cable network FM source.
AM antenna and ground terminals
Connect the supplied AM loop antenna. Use the terminals marked “AM” and “GND”. The supplied AM loop antenna will provide good AM reception in most areas. Position the loop antenna until you hear the best reception.
e RS-232C (SR5002 only)
The RS-232C port is to be used in conjunction with an external controller to control the operation of the SR5002 by using an external device.
t MONITOR OUT
This is a monitor output and each one includes both composite video and S-video confi gurations. When connecting two video monitors or televisions, be aware that the OSD interface can be used with both MONITOR OUT connections.
y Preamp Outputs
(L, R, SL, SR, SBL, SBR, C)
Jacks for L(front left), R (front right), C (Center), SL (surround left), SR (surround right), SBL (surround back left) and SBR (surround back right). Use these jacks for connection to external power amplifi ers.
u AC INLET
Plug the supplied power cable into this AC INLET and then into the power outlet on the wall. This unit can be powered by 230V AC only.
i AC OUTLETS
Connect the AC power cable of component such as a DVD or CD player to this outlet. This outlet provides power only when this unit is turned on.
Caution:
• In order to avoid potential turn-off thumps, anything
HDMI Ver 1.1
MONITOR
OUT 2
INPUT 1
R
/
P
R
IN
FLASHER
DC
OUT
IN
TRIGGER
AC IN
MODEL NO. SR5002
!3
INPUT 2
u
INPUT 3
OUTPUT
XM
!7 @0!8i
OUTPUT
If your DVD player or other device has component video connectors, be sure to connect them to these component video connectors on the unit. This unit has two component video input connectors to obtain the color information (Y, CB, CR) directly from the recorded DVD signal or other video component and one component video output connector to output it directly into the matrix decoder of the display device. By sending the pure DVD component video signal directly, the DVD signal forgoes the extra processing that normally would degrade the image. The result is vastly increased image quality, with incredibly life like colors and crisp detail. When the video convert function is enabled, video and S-video images can be output to the COMPONENT MOINTOR OUT jack.
r COMPONENT VIDEO INPUT/
plugged into this outlet should be powered up before this unit is turned on.
• The capacity of this AC outlet is 150W. Do not connect devices that consume electricity more than the capacity of this outlet. If the total power consumption of the connected devices exceeds the capacity, the protection circuit shuts down the power supply.
o Speaker outputs terminals
Seven terminals are provided for the front left, front right, front center, surround left, surround right, surround back left and surround back right speakers.
Note:
You can use surround back speaker terminals as M (Multiroom) SPEAKER B terminals, when you use no surround back speaker.
8
!0 Subwoofer Output
Connect this jack to the line level input of a powered subwoofer. If an external subwoofer amplifi er is used, connect this jack to the subwoofer amplifi er input. If you are using two subwoofers, either powered or with a 2 channel subwoofer amplifi er, connect a “Y” connector to the subwoofer output jack and run one cable from it to each subwoofer amplifi er.
!1 7.1 CHANNEL or AUX2 INPUT
By connecting a DVD Audio player, Super Audio CD multichannel player, or other components that has a multichannel port, you can playback the audio with
5.1 channel or 7.1 channel outputs.
!2 Multiroom Outputs (SR5002 only)
These are the audio output jacks for the Multi zone (Multi room). Connect these jacks to optional audio power amplifi ers to listen the source selected by the multiroom system in a remote room.
!3 REMOTE CONT. IN/OUT terminals
Connect to a Marantz component equipped with remote control (RC-5) terminals.
!4 AUDIO IN/OUT (CD, TAPE, CD-R,
TV, DVD, VCR, DSS)
These are the analog audio inputs and outputs. There are 6 audio inputs (4 of which are linked to video inputs) and 3 audio outputs (1 of which are linked to video outputs). The audio jacks are nominally labeled for cassette tape decks, compact
disc players, DVD players and etc.... The audio inputs
and outputs require RCA-type connectors.
!5 DIGITAL INPUT
(SR4002 : Dig.1 - 4, SR5002 : Dig.1-5) / OUTPUT (optical)
These are the digital audio inputs and outputs. The SR4002 has 2 digital inputs with coaxial jacks, 2 with optical jacks. The SR5002 has 2 digital inputs with coaxial jacks, 3 with optical jacks. The inputs accept digital audio signals from a CD, DVD, or other digital source component. For digital output, this is 1 optical output. The digital outputs can be connected to MD recorders, CD recorders, or other similar components.
!6 HDMI INPUT/OUTPUT
The SR4002 has 2 HDMI inputs and 1 HDMI output. The SR5002 has 3 HDMI inputs and 1 HDMI output. The input function can be selected from the menu system
. (See page 27)
OSD
!7 DC TRIGGER output terminal
(SR5002 only)
Connect a device that needs to be triggered by DC under certain conditions (screen, power strip, etc…) Use the system OSD setup menu to determine the conditions by which these jack will be active.
Note:
This output voltage is for (status) control only, It is not suffi cient for drive capability.
!8 FLASHER IN
(Flasher input terminal) (SR5002 only)
These terminals are to control the unit from each zone. Connect the control signal from a Keypad, etc.
!9
SPEAKER C SELECTOR SWITCH (SR5002 only)
The terminals can be used to connect a third set of speakers by setting the SPEAKER C selector switch to ON. For connection and use, see page 24.
ENGLISH
@0
XM antenna terminal (SR5002 only)
Plug the XM Mini-Tuner and Home Dock into XM terminal.
9
ENGLISH
REMOTE CONTROLLER
The provided remote controller is a universal remote controller. The POWER button, numeric buttons and control buttons are used in common across different input source components. The input source controlled with the remote controller changes when one of the input selector buttons is pressed.
SEND
z x c v b
n
m , . ⁄0
LEARN
SET
SOURCE
l/
SLEEP
M-CH ST
CH/
INFO
P.DIRECT
DISPLAY
AUTO
123
EX/ES
VIRTUAL
CS
456
STEREO
NIGHT
789
7.1CH IN
CL
A/D
0
+10
CAT
MUTE
SPKR A/B
CAT
MULTI/
M-SPKR
OFF
ON
SURROUND
LIP SYNC/
INPUT
dts
BAND
T.MODE
P.SCAN
HT-EQ
MEMO
VOLUME
MENU
⁄1
ENTER
T.TONE
⁄2
⁄3 ⁄4
⁄5 ⁄6
/SET UP
T.DISP
REC
PRESET
-
DISC+
CH-SEL
BASS
TV
TUNER
TAPE
REMOTE CONTROLLER
ANGLE
V-OFF
DVD
CD
AUX1
PTY
-
SUB TITLE
ATT.
VCR
CDR
AUX2
TUNING
TREBLE
EXIT
F.DIRECT
++
AUDIO
DSS
MD
AMP
‹5
⁄7 ⁄8 ⁄9 ¤0 ¤1 ¤2
¤3
¤4 ¤5 ¤6
¤7 ¤8
¤9 ‹0
‹1 ‹2 ‹3
‹4
z LEARN indicator
Indicates when the remote controller is in the LEARN mode.
x SET button
This button is used to enter learn mode and preset mode.
c / SOURCE ON/OFF button
This button is used to turn a specifi c source (such as a DVD player) on or off independently from the rest of the system.
v SLEEP button
This button is used for setting the sleep timer.
b DISPLAY button
This button is used to selects the display mode for the front display of the unit.
n Numeric buttons
These buttons are used to switch between 0 to +10 of the source components. If the source is set to the amplifi er, these buttons are used to perform operations.
(When AMP mode is selected)
1/AUTO button
This button is used to select auto surround.
2/Dolby button
This button is used to select DOLBY mode.
3/dts button
This button is used to select dts mode.
4/CSII button
This button is used to select CSII mode.
5/EX/ES button
This button is used to select EX/ES mode.
6/VIRTUAL button
This button is used to select VIRTUAL mode.
7/M-CH ST button
This button is used to select Multi Channel Stereo.
8/STEREO button
This button is used to select STEREO mode.
9/NIGHT button
Pressing this button prevents the Dolby Digital signal from playback at a loud voice. This function reduces the voice by 1/3 to 1/4 at maximum. Thus, it eliminates the occurrence of an abruptly loud voice at night. However, the function is valid only in the case when the Dolby Digital signal is entered into OPTICAL or COAXIAL and data to compress the voice exists in the signal to be played back. When this button is pressed, the “NIGHT” indicator is illuminated.
0/7.1CH IN button
This button is used to select the output of an external multi channel decoder.
(+10) A/D button
This button is used to switch between the analog and digital inputs.
m CL (Clear) button
This button is used to erase the memory or program of a source.
, SPKR A/B button (SR5002 only)
This button is used to select the speaker system. The speaker system is switched in the following sequence. A B A+B off
. CH/CAT3 (UP) / 4 (DOWN) buttons
These buttons are used to change channels.
⁄0 MULTI/CAT button (SR5002 only)
(When AMP mode is selected)
This button is used to turn on and off multi room.
⁄1 INFO button
(When AMP mode is selected)
When this button is pressed, the current setting are displayed on the TV monitor.
⁄2 T.TONE/SET UP button
(When AMP mode is selected)
This button is used to enter the test tone menu. (2-4 speakers level)
⁄3 CONTROL buttons
These buttons are used when operating PLAY, STOP, PAUSE and other commands of a source.
(When TUNER mode is selected)
T.DISP button
This button is used to select the display mode in RDS.
PTY button
This button is used to display the programme type information of the current station.
F.DIRECT button
This button is used to select the "Frequency direct input".
PRESET +/- buttons
This button is used to select a preset station up and down.
TUNING +/- buttons
This button is used to tune a frequency station up and down.
⁄4 ANGLE/V-OFF buton
(When AMP mode is selected)
This button is used to turn off the video signal.
⁄5 DISC+/CH. SEL button
(When AMP mode is selected)
This button is used to call up CH LEVEL ADJUST and adjust speaker levels or 7.1 ch input level.
⁄6 BASS +/- buttons
These buttons are used to adjust the tone control of low frequency sound for left, right and subwoofer speaker.
⁄7 SEND indicator
Indicates when the remote controller is transmitting a signal.
⁄8 / POWER ON and OFF buttons
(When AMP mode is selected)
These buttons are used to turn the unit on or off.
⁄9 SURROUND button
This button is used to selects the surround mode.
10
¤0 P.DIRECT button
When this button is pressed, the tone control circuit is bypassed.
¤1 BAND/LIP SYNC/INPUT button
(When TUNER mode is selected)
This button is used to select a radio band.
(When AMP mode is selected)
This button is used to select LIP SYNC mode.
(When TV mode is selected)
This button is used to select monitor input.
¤2 T.MODE button
(When TUNER mode is selected)
This button is used to select auto stereo mode or mono mode when the FM band is selected. The “AUTO” indicator lights in the auto stereo mode.
¤3 P.SCAN button
(When TUNER mode is selected)
This button is used to start preset scan.
¤4 MEMO/HT-EQ button
This button is used to store setting to memory or program a source.
(When AMP mode is selected)
This button is used to turn on or off HT(Home Theater)-EQ mode. This mode compensates for the audio portion of a movie sounding “bright”. When this button is pressed, “EQ” indicator light up.
¤5 MUTE button
This button is used to mute the audio for the amplifi er and television.
Note:
Set the AMP mode to use this button with the unit.
¤6 VOLUME +/- buttons
This button is used to adjust the volume for the amplifi er and television.
Note:
Set the AMP mode to use this button with the unit.
¤7 M-SPKR button (SR5002 only)
(When AMP mode is selected)
This button is used to turn on and off multi speaker.
¤8 MENU button
(When AMP mode is selected)
This button is used to call up the SETUP MAIN MENU of the unit.
¤9 1, 2, 3, 4 (CURSOR) / ENTER buttons
These buttons are used when controlling the cursor of the unit, DVD or other AV equipment.
‹0 EXIT button
(When AMP mode is selected)
This button is used to cancel setting in the setup menu.
‹1 SUBTITLE/ATT. button
(When AMP mode is selected)
When the input signal is too high and the voice distorts even by throttling the unit VOLUME control, turn on this function. “ATT ” is indicated when this function is activated. The input level reduced. Attenuator is invalid for the output signal of “REC OUT”.
Note:
This function is unavailable while the digital input is selected.
‹2 AUDIO buttons
(When DVD mode is selected)
This button is used to select one of the audio language.
ENGLISH
‹3 TREBLE +/- buttons
These buttons are used to adjust the tone control of high frequency sound for left and right speaker.
‹4 SOURCE button
These buttons are used to switch the source of your A/V Receiver / amplifer. Each time a source button is pressed, the remote controller changes to the source which was pressed. This remote controller can control 12 types of equipment. To change the A/V Receiver / amplifi er source, press this button twice within two seconds. The signal is sent when it is pressed the second time.
Notes:
• Select the AMP as the source to use this remote controller with the unit.
• In the case of the SR4002 or SR5002, the MD button cannot be used.
‹5 Infrared Transmitter and Learning
Sensor
This transmitter emits infrared light. Press the buttons while pointing the transmitter towards the infrared receiver window of the unit or other AV equipment. Be sure to also point towards other remote controllers when using the learning function.
11
ENGLISH
REMOTE CONTROL OPERATION
GENERAL INFORMATION OF REMOTE CONTROLLER TO THE UNIT
To control the unit by your remote controller, you have to select the device AMP or TUNER by pressing the SOURCE button. Please refer below for the details in AMP and TUNER mode.
AMP MODE
SOURCESOURCE
l/l/
SLEEPSLEEP
AUTOAUTO
11 22 33
CSCS
44 55 66
M-CH STM-CH ST
77 88 99
CL
CAT
CH/
INFOINFO
T.TONET.TONE /SET UP/SET UP
REC
-
DISC+DISC+
CH-SELCH-SEL
TV
TUNER
TAPE
LEARN
SET
DISPLAYDISPLAY
EX/ESEX/ES
STEREOSTEREO
7.1CH IN7.1CH IN
00
SPKR A/BSPKR A/B
CAT
MULTI/MULTI/
ENTERENTER
T.DISP
PRESET
ANGLEANGLE
V-OFFV-OFF
BASSBASS
DVD
CD
AUX1
REMOTE CONTROLLER
P.DIRECTP.DIRECT
VIRTUALVIRTUAL
NIGHTNIGHT
+10+10
M-SPKRM-SPKR
SUB TITLESUB TITLE
AUX2
TUNER MODE
SEND
OFF
ONON
SURROUNDSURROUND
LIP SYNC/LIP SYNC/ INPUTINPUT
dtsdts
BAND
T.MODE
P.SCAN
HT-EQHT-EQ
A/DA/D
MEMOMEMO
VOLUME
MUTEMUTE
SOURCE ON / OFF Turns the SR4002/SR5002 on and off POWER OFF Turns the SR4002/SR5002 off POWER ON Turns the SR4002/SR5002 on SLEEP Sets the sleep timer function DISPLAY Changes the front display mode P.DIRECT Selects the pure direct mode SURROUND Selects the surround mode AUTO (1) Selects auto surround DOLBY (2) Selects DOLBY mode dts (3) Selects dts mode
MENUMENU
CSII (4) Selects CSII mode EX/ES (5) Selects EX/ES
EXITEXIT
F.DIRECT
PTY
TUNING
-
++
AUDIOAUDIO
ATT.AT T.
TREBLETREBLE
VCR
DSS
MD
CDR
AMP
VIRTUAL (6) Selects VIRTUAL mode M-CH ST (7) Selects Multi Channel Stereo STEREO (8) Selects STEREO mode NIGHT (9) Turns on or off NIGHT mode
7.1CH IN (0) Selects the 7.1CH IN A/D (+10) Switches between the analog or digital inputs LIP SYNC / INPUT Selects the LIP SYNC mode HT-EQ Turns on or off HT-EQ mode SPKR A / B Selects the speaker system
LEARN
SOURCESOURCE
l/l/
SLEEPSLEEP
DISPLAYDISPLAY
AUTOAUTO
11 22 33
EX/ESEX/ES
CSCS
44 55 66
STEREOSTEREO
M-CH STM-CH ST
77 88 99
7.1CH IN7.1CH IN
CLCL
CAT
CH/
SPKR A/BSPKR A/B
MULTI/MULTI/
INFOINFO
T.TONET. TON E /SET UP/SET UP
T.DISPT.DISP
REC
PRESETPRESET
--
ANGLE
DISC+
CH-SEL
V-OFF
BASS
DVD
TV
TUNER
AUX1
TAPE
REMOTE CONTROLLER
SEND
OFFONSET
P.DIRECTP.DIRECT
SURROUNDSURROUND
LIP SYNC/LIP SYNC/ INPUTINPUT
dtsdts
BAND
T.MODET.MOD E
VIRTUALVIRTUAL
P.SCA NP. SC A N
NIGHTNIGHT
HT-EQHT-EQ
A/DA/D
MEMOMEMO
00
+10+10
VOLUMEVOLUME
MUTEMUTE
CAT
M-SPKRM-SPKR
MENUMENU
ENTERENTER
EXITEXIT
F.DIRECTF.DIRECT
PTYPTY
TUNINGTUNING
--
++++
AUDIO
SUB TITLE
ATT.
TREBLE
VCR
DSS
MD
CDR
CD
AMP
AUX2
MULTI / CAT Turns on or off multi room MUTE Decreases the sound temporarily M-SPKR Turns on or off multi speaker VOLUME 3 /
4
Adjusts the over all sound level INFO Displays the current setting on the monitor MENU Enters the "SETUP MENU"
ENTER
Enters the "SETUP MENU"
Confi rms the setting in "SETUP MENU" mode CURSOR Moves the cursor for setting in "SETUP MENU" mode T.TONE / SET UP Enters the test tone menu EXIT Exits from SETUP MENU CH-SEL Calls up CH LEVEL ADJUST and adjusts speaker levels or 7.1ch input
level V-OFF Turns on or off video output ATT. Reduces the input level
4
BASS 3 / TREBLE 3 /
Adjusts the tone control of low frequency sound
4
Adjusts the tone control of high frequency sound SOURCE Selects a particular source component
0-9 Inputs the numeric BAND Selects a radio band T.MODE Selects the auto stereo mode or mono mode P.SCAN Starts preset scan CL Clears the inputting MEMO Enters the tuner preset memory numbers INFO Shows preset information T.DISP Selects the display mode in RDS PTY Displays the programme type information of the current station F.DIRECT Selects the “Frequency direct input” PRESET 3 / 4Selects a preset station up and down TUNING 3 / 4Tunes a frequency station up and down
12
CONTROLLING MARANTZ COMPONENTS
1. Press the desired SOURCE button.
2. Press the desired operation buttons to play the selected component.
• For details, refer to the component’s user guide.
• It may not be possible to operate some models.
ENGLISH
CONTROLLING A MARANTZ DVD PLAYER (DVD MODE) CONTROLLING A MARANTZ VCR (VCR MODE)
LEARN
SET
SOURCESOURCE
l/l/
SLEEP
DISPLAY
AUTOAUTO
11 22 33
EX/ESEX/ES
CSCS
44 55 66
STEREOSTEREO
M-CH STM-CH ST
77 88 99
7.1CH IN7.1CH IN
CLCL
00
CAT
CH/
SPKR A/B
MULTI/
INFOINFO
T.TONET.TON E /SET UP/SET UP
T.DISPT.DISP
REC
PRESET
-
ANGLEANGLE
DISC+DISC+
CH-SELCH-SEL
V-OFFV-OFF
BASS
DVD
TV
CD
TUNER
AUX1
TAPE
REMOTE CONTROLLER
SEND
OFFOFF
ONON
P.DIRECT
SURROUND
LIP SYNC/ INPUT
dtsdts
BAND
T.MODE
VIRTUALVIRTUAL
P.SCAN
NIGHTNIGHT
HT-EQHT-EQ
A/DA/D
MEMOMEMO
+10+10
VOLUME
MUTE
CAT
M-SPKR
MENUMENU
ENTERENTER
F.DIRECTF.DIRECT
PTYPTY
TUNING
-
AUDIOAU DIO
SUB TITLESUB TITLE
ATT.AT T.
TREBLE
VCR
DSS
MD
CDR
AMP
AUX2
SOURCE ON / OFF Turns the DVD player on and off POWER OFF Turns the DVD player off POWER ON Turns the DVD player on 0-9,+10 Inputs the numeric CL Clears the inputting MEMO Calls up programming menu INFO Displays the disc information MENU Calls up the menu of DVD disc ENTER Enters the setting CURSOR Moves the cursor for setting in
"On Screen Display" mode T.TONE / SET UP Enters the test tone menu EXIT Exits from SETUP MENU T.Tone/Set up Calls up the setup menu of the
DVD player Pause Pause
EXITEXIT
Play Play Stop Stop Previous/Next S k ip s f o rwa r d o r p r e v i ous
++
chapter/track Rewind/ Forward Searchs forward or backward DISC+ DVD changer next disc ANGLE Selects the camera angle SUBTITLE Selects the subtitle language AUDIO Selects the audio language
CONTROLLING A MARANTZ CD (CD MODE)
LEARN
SET
SOURCESOURCE
l/l/
SLEEP
DISPLAY
AUTOAUTO
11 22 33
EX/ESEX/ES
CSCS
44 55 66
STEREOSTEREO
M-CH STM-CH ST
77 88 99
7.1CH IN7.1CH IN
CLCL
00
CAT
CH/
SPKR A/B
MULTI/
INFOINFO
T.TONET.TON E
/SET UP/SET UP
T.DISPT.DISP
REC
PRESET
-
ANGLEANGLE
DISC+DISC+
CH-SELCH-SEL
V-OFFV-OFF
BASS
DVD
TV
CD
TUNER
AUX1
TAPE
REMOTE CONTROLLER
SEND
OFFOFF
P.DIRECT
SURROUND
LIP SYNC/ INPUT
dtsdts
BAND
T.MODE
VIRTUALVIRTUAL
P.SCAN
NIGHTNIGHT
HT-EQHT-EQ
A/DA/D
MEMOMEMO
+10+10
VOLUME
MUTE
CAT
M-SPKR
ENTERENTER
F.DIRECTF.DIRECT
PTYPTY
TUNING
-
AUDIOAU DIO
SUB TITLESUB TITLE
ATT.AT T.
TREBLE
VCR
CDR
AUX2
SOURCE ON / OFF Turns the CD player on and off POWER OFF Turns the CD player off POWER ON Turns the CD player on
ONON
0-9 Inputs the numeric CL Clears the inputting MEMO Programs INFO Scrolls the disc information MENU Switches the display information Pause Pause Play Play Stop Stop Previous/ Next Skips forward or previous track Rewind/ Forward Searchs forward or backward
MENUMENU
DISC+ CD changer next disc
EXITEXIT
++
DSS
MD
AMP
LEARN
SET
SOURCESOURCE
l/l/
SLEEP
DISPLAY
AUTOAUTO
11 22 33
EX/ESEX/ES
CSCS
44 55 66
STEREOSTEREO
M-CH STM-CH ST
77 88 99
7.1CH IN7.1CH IN
CLCL
00
CAT CAT
CH/CH/
SPKR A/B
MULTI/
INFOINFO
T.TONET.TONE
/SET UP/SET UP
T.DISPT.DISP
RECREC
PRESET
-
ANGLE
DISC+
CH-SEL
V-OFF
BASS
DVD
TV
CD
TUNER
AUX1
TAPE
REMOTE CONTROLLER
SEND
OFF
ON
P.DIRECT
SURROUND
LIP SYNC/ INPUT
dtsdts
BAND
T.MODE
VIRTUALVIRTUAL
P.SC A N
NIGHTNIGHT
A/D
HT-EQ
MEMO
+10
VOLUME
MUTE
CAT
M-SPKR
MENUMENU
ENTERENTER
F.DIRECTF.DIRECT
PTYPTY
TUNING
-
AUDIOAU DIO
SUB TITLE
ATT.
TREBLE
VCR
DSS
CDR
AMP
AUX2
0-9,+10 Inputs the numeric LIP SYNC/INPUT Selects TV/VCR CL Clears the inputting MEMO Calls up programming menu
4
CH 3 /
Selects VCR channel up or down MENU Calls up the menu ENTER Enters the setting CURSOR Moves the cursor for setting in
"On Screen Display" mode EXIT Exits the programming menu REC Record Pause Pause Play Play Stop Stop Previous / Next Skips forward or previous track
EXITEXIT
Rewind / Forward Searchs forward or backward AUDIO Selects the audio language
++
MD
SOURCE ON / OFF Turns the VCR on and off
13
ENGLISH
CONTROLLING A MARANTZ CD RECORDER (CDR MODE)
LEARN
SET
SOURCESOURCE
l/l/
SLEEP
DISPLAY
AUTOAUTO
11 22 33
EX/ESEX/ES
CSCS
44 55 66
STEREOSTEREO
M-CH STM-CH ST
77 88 99
7.1CH IN7.1CH IN
CLCL
00
CAT
CH/
SPKR A/B
MULTI/
INFOINFO
T.TONET.TON E /SET UP/SET UP
T.DISPT.DISP
RECREC
PRESET
-
ANGLE
DISC+
CH-SEL
V-OFF
BASS
DVD
TV
CD
TUNER
AUX1
TAPE
REMOTE CONTROLLER
SEND
OFFOFF
P.DIRECT
SURROUND
LIP SYNC/ INPUT
dtsdts
BAND
T.MODE
VIRTUALVIRTUAL
P.SCAN
NIGHTNIGHT
A/D
HT-EQ
MEMO
+10
VOLUME
MUTE
CAT
M-SPKR
MENUMENU
ENTERENTER
F.DIRECTF.DIRECT
PTYPTY
TUNING
-
SUB TITLE
AUDIO
ATT.
TREBLE
VCR
DSS
CDR
AMP
AUX2
SOURCE ON / OFF Turns the CD recorder on and off POWER OFF Turns the CD recorder off POWER ON Turns the CD recorder on
ONON
0-9 Inputs the numeric CL Clears the inputting MEMO Programs INFO Scrolls the disc information MENU Switches the display information REC Record Pause Pause Play Play Stop Stop Previous / Next Skips forward or previous track Rewind / Forward Searchs forward or backward
EXITEXIT
++
MD
CONTROLLING A MARANTZ MD DECK (MD MODE)
LEARN
SET
SOURCESOURCE
l/l/
SLEEP
DISPLAY
AUTOAUTO
11 22 33
EX/ESEX/ES
CSCS
44 55 66
STEREOSTEREO
M-CH STM-CH ST
77 88 99
7.1CH IN7.1CH IN
CLCL
00
CAT
CH/
SPKR A/B
MULTI/
INFOINFO
T.TONET.TON E
/SET UP/SET UP
T.DISPT.DISP
RECREC
PRESET
-
ANGLE
DISC+
CH-SEL
V-OFF
BASS
DVD
TV
CD
TUNER
AUX1
TAPE
REMOTE CONTROLLER
SEND
OFFOFF
P.DIRECT
SURROUND
LIP SYNC/
INPUT
dtsdts
T.MODE
VIRTUALVIRTUAL
P.SCAN
NIGHTNIGHT
A/D
HT-EQ
MEMO
+10
VOLUME
MUTE
CAT
M-SPKR
MENUMENU
ENTERENTER
F.DIRECTF.DIRECT
PTYPTY
TUNING
-
SUB TITLE
AUDIO
ATT.
TREBLE
VCR
DSS
CDR
AMP
AUX2
SOURCE ON / OFF Turns the MD deck on and off POWER OFF Turns the MD deck off POWER ON Turns the MD deck on
ONON
0-9 Inputs the numeric CL Clears the inputting MEMO Programs MENU Switches the display information REC Record Pause Pause Play Play Stop Stop Previous / Next Skips forward or previous track Rewind / Forward Searchs forward or backward
EXITEXIT
++
MD
CONTROLLING A MARANTZ TAPE DECK (TAPE MODE)
LEARN
SET
SOURCESOURCE
l/l/
SLEEP
DISPLAY
AUTOAUTO
11 22 33
EX/ESEX/ES
CSCS
44 55 66
STEREOSTEREO
M-CH STM-CH ST
77 88 99
7.1CH IN7.1CH IN
CLCL
00
CAT
CH/
SPKR A/B
MULTI/
INFOINFO
T.TONET.TON E
/SET UP/SET UP
T.DISPT.DISP
RECREC
PRESET
-
ANGLE
DISC+
CH-SEL
V-OFF
BASS
DVD
TV
CD
TUNER
AUX1
TAPE
REMOTE CONTROLLER
SEND
OFFOFF
ONON
P.DIRECT
SURROUND
LIP SYNC/
INPUT
dtsdts
T.MODE
VIRTUALVIRTUAL
P.SCAN
NIGHTNIGHT
A/D
HT-EQ
MEMO
+10
VOLUME
MUTE
CAT
M-SPKR
MENUMENU
ENTERENTER
F.DIRECTF.DIRECT
PTYPTY
TUNING
-
SUB TITLE
AUDIO
ATT.
TREBLE
VCR
DSS
CDR
AMP
AUX2
SOURCE ON / OFF Turns the TAPE deck on and off POWER OFF Turns the TAPE deck off POWER ON Turns the TAPE deck on 0-9 Inputs the numeric CL Clears the inputting MEMO Programs REC Record Pause Pause Play Play Stop Stop Previous / Next Skips forward or previous track Rewind / Forward Searchs forward or backward
EXITEXIT
++
MD
14
CONTROLLING A MARANTZ UNIVERSAL DOCK (AUX1 MODE)
ENGLISH
LEARN
SET
SOURCESOURCE
l/l/
SLEEP
DISPLAY
AUTOAUTO
112233
EX/ESEX/ES
CSCS
445566
STEREOSTEREO
M-CH STM-CH ST
778899
7.1CH IN7.1CH IN
CLCL
00
CAT
CH/
SPKR A/B
MULTI/
INFOINFO
T.TONET.TON E /SET UP/SET UP
T.DISPT.DISP
RECREC
PRESET
-
ANGLE
DISC+
CH-SEL
V-OFF
BASS
DVD
TV
CD
TUNER
AUX1
TAPE
REMOTE CONTROLLER
SEND
OFFOFF
ONON
P.DIRECT
SURROUND
LIP SYNC/ INPUT
dtsdts
T.MODE
VIRTUALVIRTUAL
P.SCAN
NIGHTNIGHT
A/D
HT-EQ
MEMO
+10
VOLUME
MUTE
CAT
M-SPKR
MENUMENU
ENTERENTER
EXITEXIT
F.DIRECTF.DIRECT
PTYPTY
TUNING
-
SUB TITLE
AUDIO
ATT.
TREBLE
VCR
DSS
MD
CDR
AMP
AUX2
POWER OFF Turns the UNIVERSAL DOCK (Dock connector) OFF POWER ON Turns the UNIVERSAL DOCK (Dock connector) ON INFO Mode MENU Call up the menu ENTER Enter the setting CURSOR UP Select contents Up CURSOR DOWN Select contents Down Pause Pause Play Play / Pause Stop Stop Previous/Next Skips forward or previous tracks P.SCAN Shuffl e
++
SOURCE ON / OFF Turns the UNIVERSAL DOCK (Dock connector) ON and OFF
15
ENGLISH
BASIC OPERATION
NORMAL MODE
(
When operating Marantz AV equipment products
This remote controller is preset with a total of 12 types of remote codes, including Marantz TV (television), DVD, VCR (VCR deck), DSS (satellite broadcasting tuner), TUNER, CD, CD-R, MD, TAPE (tape deck), AUX1, AUX2, and AMP (amplifi er). Learning is not necessary for Marantz products. You can use these products without setting any codes.
1. Press the SOURCE button.
For this example, press DVD. Pressing the SOURCE button once changes the remote control to the settings for the source that was pressed. To change the amplifi er on other source, press the SOURCE button twice (double-click). The code is sent, and then the amplifi er source changes to DVD.
SETTING THE BACK LIGHT
Each time press the buttons, illuminate button 2 seconds. To turn off back light, press and hold down the SET and OFF button until SEND indicator blinks twice. To turn on it again, press and hold down the SET and ON button until SEND indicator blinks twice. Initial is back light ON.
PRESET MODE
(When operating non-Marantz AV equipment products)
This remote controller is preset with remote control codes from AV equipment by other manufacturers. The preset codes are TV, VCR, DVD and DSS. Settings can be made in one of two ways. When the preset codes are set, the following codes are contained in the source button of the remote controller.
See the attached manufacturer number list for the preset manufacturers, devices, preset numbers, and other settings.
Remote controller source name
TV TV Television DVD DVD DVD player VCR VCR Video deck DSS SATELLITE Satellite broadcasting
Corresponding preset code
Device name
tuner equipment
Importants:
• Some codes may be not match your equipment. In this case, you can use LEARN mode to store these
codes.
• The preset codes do not cover full functions.
)
If you need extra function, use LEARN mode to
store extra function.
• Wen the batteries are getting weak, the preset procedure is not successful.
PROGRAMMING WITH THE 4-DIGIT CODE
TUNING
PRESET
-
-
1.
DISC+
CH-SEL
BASS
TVTV
TUNER
TAPE
REMOTE CONTROLLER
ANGLE
V-OFF
DVDDVD VCRVCR
CD
AUX1
SUB TITLE
++
AUDIO
ATT.
CDR
AUX2
1.
TREBLE
DSSDSS
MD
AMP
2.
SOURCE
l/
SLEEP
DISPLAY
AUTO
11 22 33
CS
44 55 66
STEREO
M-CH ST
77 88 99
7.1CH IN
CL
CAT
CH/
SPKR A/B
1. Press and hold down the SOURCE button for the appliance which should be controlled and press SET button until the SEND indicator blinks twice. Then back light fl ushes.
2. Press the 4-digit code for appliance (code table at the end of this book) When the procedure is successful, the indicator will blink twice.
Note:
If the indicator did not blink twice, then repeat steps 1 through 2 and try entering the same code again.
SCANNING THE CODE TABLE
SOURCE
SEND
LEARN
3.
SURROUND
LIP SYNC/ INPUT
T.MODE
3.
AUDIO
TREBLE
DSSDSS
MD
5.
AMP
2.
2.
SOURCESOURCE
l/l/
SLEEP
DISPLAY
AUTO
123
EX/ES
CS
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
BASS
DVDDVD VCRVCR
TVTV
CD
TUNER
AUX1
TAPE
REMOTE CONTROLLER
OFFONSET
P.DIRECT
dts
VIRTUAL
ATT.
CDR
AUX2
1. Switch on the appliance which should be controlled.
l/
SLEEP
DISPLAY
AUTO
123
CS
456
STEREO
M-CH ST
789
7.1CH IN
CL
CAT
CH/
SPKR A/B
MULTI/
INFO
T.TONE /SET UP
EX/ES
EX/ES
00
0
CAT
ENTER
OFFONSET
P.DIRECT
SURROUND
dts
T.MODE
VIRTUAL
NIGHT
A/D
+10
VOLUME
MUTE
SEND
OFFONSET
P.DIRECT
SURROUND
dts
T.MODE
VIRTUAL
NIGHT
A/D
+10
MUTE
M-SPKR
2. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice. Then back light fl ushes.
Aim the remote control at the appliance and
3.
slowly alternate between pressing CH+ button and the
SOURCE ON/OFF
appliance.
Stop when the appliance turns off.
4.
Press ENTER button once to lock in the code.
5.
CHECKING THE CODE
LIP SYNC/ INPUT
SEND
P.SCAN
HT-EQ
MEMO
1.
1.
LEARN
SOURCE
l/
SLEEP
DISPLAY
AUTO
123
ANGLE
DISC+
CH-SEL
V-OFF
BASS
DVDDVD VCRVCR
TVTV
CD
TUNER
AUX1
TAPE
REMOTE CONTROLLER
P.DIRECT
SUB TITLE
ATT.
AUX2
OFFONSET
dts
CDR
3.
SURROUND
LIP SYNC/ INPUT
4.
AUDIO
TREBLE
DSSDSS
MD
AMP
2.
1. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice then back light fl ushes.
Press the INFO button.
2.
The SEND indicator will blink twice.
To view the code for fi rst digit, press 1 once.
3.
Wait 3 seconds, count the SEND indicator
LIP SYNC/
INPUT
blinks (e.g. 3 blinks = 3) and write down the number.
Note:
P.SCAN
HT-EQ
MEMO
VOLUME
If a code digit is “0”, the SEND indicator will not blink.
Repeat step 3 three more times for remaining
4.
digits. Use 2 for the second digit, 3 for the third
MENU
EXIT
digit, and 4 for the fourth digit.
button for the
OFFONSET
SOURCE
l/
P.DIRECT
SLEEP
AUTO
123
CS
4 56
M-CH ST
789
CL
CAT
CH/
INFO
T.TONE /SET UP
SURROUND
DISPLAY
LIP SYNC/ INPUT
dts
T.MODE
EX/ES
VIRTUAL
P.SCAN
STEREO
NIGHT
HT-EQ
7.1CH IN
A/D
MEMO
0
+10
VOLUME
MUTE
SPKR A/B
CAT
MULTI/
M-SPKR
MENU
ENTER
EXIT
RESETTING THE CODE
SEND
LEARN
OFFONSET
SOURCE
l/
P.DIRECT
1.
1.
SLEEP
AUTO
123
DISC+
CH-SEL
TVTV
TUNER
TAPE
DISPLAY
dts
ANGLE
SUB TITLE
V-OFF
ATT.
BASS
DVDDVD VCRVCR
CDR
CD
AUX2
AUX1
REMOTE CONTROLLER
SURROUND
LIP SYNC/ INPUT
AUDIO
TREBLE
DSSDSS
MD
2.
AMP
1. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice.
Then back light fl ushes.
Press the below codes to reset.
2.
TV : 1000 DVD : 2000 VCR : 3000 DSS : 4000
The indicator will blink twice.
Note:
After this procedure, the selected SOURCE button is set initial code.
LEARN
SOURCE
l/
SLEEP
DISPLAY
AUTO
123
EX/ES
CS
4 56
STEREO
M-CH ST
789
7.1CH IN
CL
0
CAT
CH/
SPKR A/B
CAT
MULTI/
INFO
P.DIRECT
VIRTUAL
SEND
OFFONSET
SURROUND
LIP SYNC/ INPUT
dts
T.MODE
P.SCAN
NIGHT
HT-EQ
A/D
MEMO
+10
VOLUME
MUTE
M-SPKR
MENU
16
BASS
TREBLE
CH-SEL
V-OFF
ATT
LEARN MODE
This remote controller is capable of learning and storing codes used by other remote controls that you already own. For codes which are not learned, the remote controller will transmit either the Marantz preset codes from the initial settings, or remote codes from another manufacturer’s AV equipment which is set by the customer. The receiver sensor for the remote controller signals is located at the top of the remote controller.
Notes:
• This remote controller is capable to learn around 60 codes.
• When the batteries are getting weak , the learing procedure is not successful.
LEARNING PROCEDURE
1. Place the remote controller so that its infrared signal transmitter is facing the infrared signal receiver on the Marantz remote controller at a distance of about 0.05 m (2 inches).
0.05 m
S
Y ST
E M R E
M O
R
T
C
E
5
C
5
O 0 0
N
S
T
R
R
O LL E R
2. Press and hold down the SET and MENU buttons until LEARN indicator blinks.
SET
OFF
DISPLAY
P.DIRECT
ON
SURROUND
LIP SYNC/ INPUT
dts
SOURCE
l/
SLEEP
AUTO
123
3. Select the SOURCE button to select the SOURCE.
BASS
DVDDVD
TVTV
CDCD
TUNERTUNER
AUX1AUX1
TAPETA PE
REMOTE CONTROLLER
MULTI/
INFO
TREBLE
VCRVCR
DSSDSS
MDMD
CDRCDR
AMPAMP
AUX2AUX2
4. Select the button to be learned.
• LEARN indicator lights up.
l/
P.DIRECT
DISPLAY
SURROUND
LIP SYNC/ INPUT
dts
T.MODE
EX/ES
VIRTUAL
SLEEP
AUTO
123
CS
456
5. Press and hold the button of the original remote controller to learn until the SEND indicator blinks twice.
Notes:
• When the SEND indicator blinks once, repeat this step.
• If the LEARN indicator fl ashes when the SEND indicator is lit, then the button cannot be learned.
• When the memory of the remote controller is full, the LEARN and SEND indicators blink once. If you want to learn the code, you should erase other learned button.
Repeat steps 4 and 5 to learn other buttons in
6.
same SOURCE.
Repeat steps 3 to 6 to learn other SOURCE.
7.
When you have finished programming the
8.
remote controller, press the SET button, then LEARN indicator stops blinking and exits from the LEARN mode.
SEND
LEARN
SOURCE
SLEEP
AUTO
OFFONSET
l/
P.DIRECT
SURROUND
DISPLAY
LIP SYNC/
dts
INPUT
Notes:
• When the SEND indicator blinks once again, the transmitting code is unavailable for remote
CAT
M-SPKR
MENU
controller, or the transmitting signal is intercepted by noise.
• If no buttons are pressed for approximately 1 minutes while in the LEARN mode, the remote
ENTER
controller automatically exits from the LEARN mode.
ERASING PROGRAMMED CODES (RETURNING TO INITIAL SETTINGS)
Codes can be erased in three ways: by buttons, sources, and by all memory contents.
Erasing the code by buttons
Press and hold down the SET and MENU
1.
buttons until LEARN indicator blinks.
CAT
MULTI/
SOURCE
SLEEP
OFFONSET
l/
P.DIRECT
DISPLAY
AUTO
dts
123
SURROUND
LIP SYNC/ INPUT
2. Select the SOURCE button to select the button to be erased.
DVDDVD
VCRVCR
TVTV
TUNERTUNER
TAPETA PE
REMOTE CONTROLLER
DSSDSS
CDRCDR
CDCD
AMPAMP
AUX2AUX2
AUX1AUX1
3. Press and hold down the SLEEP button and press the learned button twice to be erased.
• SEND indicator blinks twice and the mode
returns to LEARN mode.
SOURCE
OFFONSET
l/
P.DIRECT
SLEEP
DISPLAY
dts
AUTO
123
SURROUND
LIP SYNC/
INPUT
4. To return the NORMAL mode, press the SET button.
Erasing the code by SOURCE
1. Press and hold down the SET and MENU
buttons until LEARN indicator blinks.
SOURCE
SLEEP
OFFONSET
l/
P.DIRECT
DISPLAY
dts
AUTO
123
SURROUND
LIP SYNC/
INPUT
2. Press and hold down the SLEEP button and
M-SPKR
INFO
MDMD
INFO
MENU
ENTER
CAT
MULTI/
M-SPKR
MENU
ENTER
3. Press ENTER button to continue erasing.
• The SEND indicator blinks twice and the mode returns to LEARN mode.
• To cancel the erasing operation, do not
ENTER
press
button and simply touch any
other button.
INFO
T.TONE /SET UP
MENU
ENTER
EXIT
4. To return the NORMAL mode, press the SET
button.
Erasing the all SOURCES
1. Press and hold down the SET and MENU buttons until LEARN indicator blinks.
CAT
MULTI/
SOURCE
l/
P.DIRECT
SLEEP
DISPLAY
AUTO
123
OFFONSET
SURROUND
LIP SYNC/ INPUT
dts
M-SPKR
INFO
MENU
ENTER
2. Press and hold down the SLEEP button and press POWER ON and POWER OFF button.
• LEARN indicator lights.
SOURCE
SLEEP
AUTO
OFFONSET
l/
P.DIRECT
DISPLAY
dts
123
SURROUND
LIP SYNC/ INPUT
3. Press ENTER button to continue erasing.
• The SEND indicator blinks twice and the
mode returns to LEARN mode.
• To cancel the erasing operation, do not
ENTER
press
button and simply touch any
other button.
INFO
T.TONE /SET UP
MENU
ENTER
EXIT
ENGLISH
press the learned SOURCE button twice to be erased.
• LEARN indicator lights.
SOURCE
OFFONSET
l/
P.DIRECT
SLEEP
DISPLAY
AUTO
dts
123
SURROUND
LIP SYNC/ INPUT
.
BASS
TREBLE
DVDDVD
VCRVCR
TVTV
TUNERTUNER
TAPETAPE
DSSDSS
MDMD
CDRCDR
CDCD
AMP
AUX2AUX2
AUX1AUX1
4. To return the NORMAL mode, press the SET button.
Note:
Erasing codes will return to the factory preset code, or there will leave empty if the button has no factory preset code.
17
ENGLISH
SR
C
SBR
MULTI.
OUT
SBL
L
R
R
XM
L
L
L
R
IN
OUT
REMOTE CONT.
OPT
DIGITAL OUT
(
AUX2
)
7.1CH INPUT
SBL
SBR
RS-232C
SPEAKER C
OFFONON
R
L
FM
(
75
)
GNDAMAM
C
R
/
P
R
C
B
/
P
B
Y
C
R
/
P
R
C
B
/
P
B
Y
1
ANTENNA
DIGITAL IN
OUTININ
CD/CDR
OUTININ
TAPE
VCR
DVDTVTV
AUDIO
DSS
OUT
C
R
/
P
R
C
B
/
P
B
Y
DSS
DVD
VCR IN
VCR OUT
MONITOR OUT
MONITOR
OUT 2
INPUT
1
INPUT
2
S-VIDEO
VIDEO
AC IN
MODEL NO. SR5002
FLASHER
IN
PRE OUT
AC OUTLETS
120V 60Hz
SWITCHED
1.25A 150W
CENTER
SURROUND
SURROUND BACK
SPEAKER C/MULTI SPEAKER
FRONT A OR B.CENTER.
FRONT A
+
B : 8 OHMS
SPEAKER SYSTEMS
FRONT B B
FRONT A A
SURR.SURR BACK : 6-8 OHMS
1
4
DC
TRIGGER
3
INPUT
3
INPUT 3
OUTPUT
INPUT 2
INPUT 1
HDMI Ver 1.1
COMPONENT
VIDEO
SW
PRE OUT
R
R
L
L
L
R
CENTER
SURROUND
SURROUND BACK
SPEAKER C/MULTI SPEAKER
FRONT A OR B.CENTER.
FRONT A
+
B : 8 OHMS
SPEAKER SYSTEMS
FRONT B B
FRONT A A
SURR.SURR BACK : 6-8 OHMS
CONNECTIONS
SPEAKER PLACEMENT
The ideal surround speaker system for this unit is 7­speaker systems, using front left and right speakers, a center speaker, surround left and right speakers, a surround back left and right speakers, and a subwoofer. For best results we recommend that all front speakers be of the same type, with identical or similar driver units. This will deliver smooth pans across the front sound stage as the action moves from side to side. Your center channel speaker is very important as over 80% of the dialog from a typical motion picture emanates from the center channel. It should possess similar sonic characteristics to the main speakers. Surround channel speakers need not be identical to the front channel speakers, but they should be of high quality. The surround back speaker is useful for playback of Dolby Digital Surround EX or DTS-ES. One of the benefi ts of both Dolby Digital and DTS is that surround channels are discrete full range, while they were frequency limited in earlier “Pro Logic’ type systems. Bass effects are an important part of home theater. For optimal enjoyment a subwoofer should be used as it is optimized for low frequency reproduction. If you have full range front speakers, however, they may be used in place of a subwoofer with proper setting of the switches in the menu system.
Surround Left
Surround Back Left
Surround Back Right
Front left and right speakers
We recommend to set the front L and R speakers
150°
135°
110°
Surround Right
with 45-60 degrees from the listening position.
Center speaker
Align the front line of the center speaker with the front L/R speakers. Or place the center speaker a little backward from the line.
Subwoofer
90°
Front Center
30°
Front Right
Front Left
Surround left and right speakers
When this unit is used in surround operation, the preferred location for surround speakers is on the side walls of the room, at or slightly behind the listening position. The center of the center speaker should face the center of the room.
Surround back left and right speakers
Surround back speakers are required when a full 7.1-
CONNECTING SPEAKERS
Passive
subwoofer
Power
Amplifi er
INVERT
INPUT
INPUT
OUTPUT
LEVEL
MASTERSLAVE
MIN MAX
SPEAKER SYSTEM MINIMUM 4 OHMS
BTL REMOTE CONT.EXT. CONT. IN
VIDEO/
+5~13V DC
Powered
subwoofer
IN
SYSTEM OUT OUT
S
E
U
F
or
Surround
BACK
Right Left
channel system is installed. Speakers should be placed on a rear wall, behind the listening position. The center of the center speaker should face the center of the room.
Subwoofer
We recommend using a sub-woofer to have maximum bass effect. As the subwoofer only handles low frequencies, you can place it any where in the room.
HEIGHT OF THE SPEAKER UNITS
Front left and right speakers, and a center speaker
Align the tweeters and mid-range drivers on the three front speakers at the same height, as best as
(
)
FM
75
GND
ANTENNA
LLSLSLCCSBL
L
R
RRSRSRSWSWSBR
(
)
AUX2
7.1CH INPUT
RS-232C
SLSLSBL
L
RRSR
PRE OUT
PRE OUT
SPEAKER C
OFF
C
SWSWSBR
SW
VIDEO
S-VIDEO
TVTVDVD
MULTI.
OUT
RRL
RRL
FRONT A OR B.CENTER.
FRONT A OR B.CENTER.
FRONT A
FRONT A
VCR IN
VCR OUT
ININOUT
VCR
DVD
FRONT
FRONT
+
+
B : 8 OHMS
B : 8 OHMS
FRONT
FRONT
DSS
MONITOR OUT
DSS
LLR
LLR
SURROUND BACK
SURROUND BACK
SPEAKER C/MULTI SPEAKER
SPEAKER C/MULTI SPEAKER
SURR.SURR BACK : 6-8 OHMS
SURR.SURR BACK : 6-8 OHMS
INPUT
1
INPUT
2
TAPE
AUDIO
R
R
1
Y
C
R
/
P
R
C
B
/
P
B
Y
OUT
OUT
CD/CDR
R
L
L
R
SURROUND
SURROUND
L
L
SPEAKER
SPEAKER
SYSTEMS
SYSTEMS
COMPONENT
INPUT
VIDEO
3
Y
C
R
/
P
R
C
B
/
P
B
554
221
3
DIGITAL IN
CENTER
CENTER
C
DIGITAL OUT
MONITOR
OUT 2
INPUT 1
C
R
/
P
R
B
/
P
B
IN
FLASHER
DC
OUT
OPT
REMOTE CONT.
SWITCHED
1.25A 150W
AC OUTLETS
120V 60Hz
IN
TRIGGER
AC IN
MODEL NO. SR5002
INPUT 2
HDMI Ver 1.1
INPUT 3
XM
OUTPUT
possible.
Surround left and right speakers, and surround back speaker
Place the surround left, right and surround back speakers higher than your ears by about 70cm – 1m. Also place the speakers at the same height, as best as possible.
Center
Right Left
70cm 1m
CONNECTING SPEAKER WIRE
Strip away approx. 3/8 inch (10 mm) of wire
1.
insulation.
Twist the bared wire ends tight, to prevent short
2.
22°
Front B
SR5002 only
Right Left
Front A
Right
circuits.
Note:
Use magnetically-shielded speakers for front left, right and the center speakers when the speakers are installed near the TV.
Loosen the knob by turning it counterclockwise.
3.
4. Insert the bare part of the wire into the hole in side of each terminal.
Tighten the knob by turning it clockwise to
5.
secure the wire.
Left
Surround
1. 2.
10 mm
3. 4. 5.
18
Caution:
SR
C
SBR
MULTI.
OUT
SBL
L
R
R
L
L
L
R
IN
OUT
REMOTE CONT.
OPT
DIGITAL OUT
(
AUX2
)
7.1CH INPUT
SBL
SBR
RS-232C
SPEAKER C
OFFONON
R
L
FM
(
75
)
GNDAMAM
C
R
/
P
R
C
B
/
P
B
Y
C
R
/
P
R
C
B
/
P
B
Y
1
ANTENNA
DIGITAL IN
OUTININ
CD/CDR
OUTININ
TAPE
VCR
DVDTVTV
AUDIO
DSS
OUT
C
R
/
P
R
C
B
/
P
B
Y
DSS
DVD
VCR IN
VCR OUT
MONITOR OUT
MONITOR
OUT 2
INPUT
1
INPUT
2
S-VIDEO
VIDEO
SFLASHER
NIN
PRE OUT
AC OUTLETS
120V 60Hz
SWITCHED
1.25A 150W
CENTER
SURROUND
SURROUND BACK
SPEAKER C/MULTI SPEAKER
FRONT A OR B.CENTER.
FRONT A
+
B : 8 OHMS
SPEAKER SYSTEMS
FRONT B B
FRONT A A
SURR.SURR BACK : 6-8 OHMS
1
4
3
INPUT
3
COMPONENT
VIDEO
OPT
DIGITAL OUT
DIGITAL IN
OUTININ
CD/CDR
OUTININ
TAPE
AUDIO
4
• Be sure to use speakers with the specifi ed impedance as shown on the rear panel of this unit.
• To prevent damage to circuitry, do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit.
• Do not touch the speaker terminals when the power is on. It may cause you to receive an electric shocks.
• Do not connect more than one speaker cable to one speaker terminal. Doing so may damage this unit.
Note:
Be sure to connect the positive and negative cables for the speaker properly. If they are miss-connected, the signal phase will be reversed and the signal quality will be corrupted.
CONNECTING A SUBWOOFER
Use the PRE OUT SUBWOOFER jack to connect a powered subwoofer (power amplifi er built in). If your subwoofer is a passive type (power amplifi er is not built in), connect a monaural power amplifi er to the PRE OUT SUBWOOFER jack and connect the subwoofer to the amplifi er.
CONNECTING AUDIO COMPONENTS
DIGITAL
INPUT
CD recorder
OUT IN DIGITAL OUTPUT
LRL
RL
R
R L
(
)
FM
75
ANTENNA
LLSLSLCCSBL
L
R
RRSRSRSWSWSBR
(
)
AUX2
7.1CH INPUT
RS-232C
SLSLSBL
L
RRSR
PRE OUT
DIGITAL OUTPUT
GND
SPEAKER C
OFF
C
SWSWSBR
VIDEO
S-VIDEO
TVTVDVD
MULTI.
OUT
RRL
FRONT A OR B.CENTER.
FRONT A
FRONT
+
B : 8 OHMS
DVD
CD player
VCR IN
VCR OUT
ININOUT
VCR
FRONT
R L RL
DSS
MONITOR OUT
DSS
AUDIO
AUDIO
R
LLR
SURROUND BACK
SPEAKER C/MULTI SPEAKER
SURR.SURR BACK : 6-8 OHMS
INPUT
INPUT
1
2
Y
OUT
OUT
TAPE
TAPE
L
1
C
R
/
P
R
C
B
/
P
B
OUT
OUT
CD/CDR
CD/CDR
R
SURROUND
R L R L
OUT IN
LRL
L R
C
Y
L
SPEAKER SYSTEMS
Tape Deck
ENGLISH
R
L R
Analog Audio
L R
COMPONENT
INPUT
VIDEO
3
C
C
B
/
P
B
Y
C
R
/
P
R
B
/
P
B
554
554
221
3
OPT
OPT
DIGITAL OUT
DIGITAL OUT
DIGITAL IN
DIGITAL IN
CENTER
SWITCHED
1.25A 150W
AC OUTLETS
120V 60Hz
Digital Audio (coaxial)
MONITOR
OUT 2
R
/
P
R
IN
Digital Audio (optical)
FLA
OUT
I
REMOTE CONT.
The output audio signal from the TAPE OUT jack and the CD/CD-R OUT jack is the same signal which is currently selected.
Caution:
Do not connect this unit and other components to mains power until all connections between components have been completed.
Notes:
• Insert all plugs and connectors securely. Incomplete connections may make noise.
• Be sure to connect the left and right channels properly.
Red connectors are for the R (right) channel, and
• Be sure to connect input and output properly.
• Refer to the instructions for each component that is
• Do not bind audio/video connection cables with
white connectors are for the L (left) channel.
connected to this unit.
power cords and speaker cables this will result in generating a hum or other noise.
CONNECTING DIGITAL AUDIO COMPONENTS
• There are 4 digital inputs (SR4002), 5 digital inputs (SR5002), 2 coaxial jacks and 2 optical jacks (SR4002), 3 optical jacks (SR5002), on the rear panel. You can use these jacks to input PCM, Dolby Digital and DTS bitstream signals from a CD, DVD, or other digital source components.
• There is one optical output jack on the rear panel. These jacks can be connected to a CD recorder, or a MD deck inputs, respectively.
• Refer to the instructions for each component. To setup the digital audio format of DVD player, or other digital source’s connected to digital input jacks.
• Use fiber optical cables (optical) for DIG-1,2 (SR4002), DIG-1,2,3 (SR5002), input jacks. Use 75 ohms coaxial cables (for digital audio or video) for DIG-3,4 (SR4002), DIG-4,5 (SR5002), input jacks.
• You can designate the input for each digital input/ output jacks according to your component. See page 27.
Notes:
• There is no Dolby Digital RF input jack. Please use an external RF demodulator Dolby Digital decoder when connecting the Dolby Digital RF output jack of the video disc player to the digital input jack.
• The digital signal jacks on this unit conform to the EIA standard. If you use a cable that does not conform to this standard, this unit may not function properly.
• Each type of audio jack works independently. Signals input through the digital and analog jacks are output through the corresponding digital and analog jacks, respectively.
19
ENGLISH
SR
C
SBR
MULTI.
OUT
SL
SBL
L
R
R
L
L
L
R
(
AUX2
)
7.1CH INPUT
SBL
SBR
RS-232C
SPEAKER C
OFFONON
R
L
FM
(
75
)
GNDAMAM
C
R
/
P
R
C
B
/
P
B
Y
Y
1
ANTENNA
DIGITAL IN
OUTININ
CD/CDR
OUTININ
TAPE
VCR
DVDTVTV
AUDIO
DSS
OUT
C
R
/
P
R
C
B
/
P
B
Y
DSS
DVD
VCR IN
VCR OUT
MONITOR OUT
INPUT
1
INPUT
2
S-VIDEO
VIDEO
PRE OUT
CENTER
SURROUND
SURROUND BACK
SPEAKER C/MULTI SPEAKER
FRONT A OR B.CENTER.
FRONT A
+
B : 8 OHMS
SPEAKER SYSTEMS
FRONT B B
FRONT A A
SURR.SURR BACK : 6-8 OHMS
1
4
3
INPUT
3
CCOMPONENT
VIDEO
VIDEO
TV
DSS
DSS
MONITOR OUT
DIGITAL IN
2
TV
SR
C
SBR
MULTI.
OUT
SL
SBL
L
R
R
L
L
L
R
IN
OUT
REMOTE CONT.
OPT
DIGITAL OUT
(
AUX2
)
7.1CH INPUT
SBL
SBR
RS-232C
SPEAKER C
OFFONON
R
L
FM
(
75
)
GNDAMAM
C
R
/
P
R
C
B
/
P
B
Y
C
R
/
P
R
C
B
/
P
B
Y
1
ANTENNA
DIGITAL IN
OUTININ
CD/CDR
OUTININ
TAPE
VCR
DVDTVTV
AUDIO
DSS
OUT
C
R
/
P
R
C
B
/
P
B
Y
DSS
DVD
VCR IN
VCR OUT
MONITOR OUT
MONITOR
OUT 2
INPUT
1
INPUT
2
S-VIDEO
VIDEO
LFLASHER
IN
PRE OUT
AC OUTLETS
120V 60Hz
SWITCHED
1.25A 150W
CENTER
SURROUND
SURROUND BACK
SPEAKER C/MULTI SPEAKER
FRONT A OR B.CENTER.
FRONT A
+
B : 8 OHMS
SPEAKER SYSTEMS
FRONT B B
FRONT A A
SURR.SURR BACK : 6-8 OHMS
1
4
3
INPUT
3
COMPONENT
VIDEO
DVD
VCR IN
VCR OUT
MONITOR OUT
INPUT
1
C
R
/
P
R
C
B
/
P
B
Y
1
DIGITAL IN
VCR
DVD
OUT
S-VIDEO
VIDEO
COMPONENT
VIDEO
CONNECTING VIDEO COMPONENTS
DVD player
DIGITAL
OUT
AUDIO
OUT
S-VIDEO
LR
L R
VIDEO
VIDEO
S-VIDEO
GND
SPEAKER C
OFF
C
SWSWSBR
S-VIDEO OUT IN
S-VIDEO
SBL
TVTVDVD
MULTI.
OUT
RRL
FRONT A OR B.CENTER.
FRONT A
L R L R LR
(
)
FM
75
ANTENNA
LLSLSLCCSBL
L
R
RRSRSRSWSWSBR
(
)
AUX2
7.1CH INPUT
RS-232C
SL
L
RRSR
PRE OUT
OUT
DVD
VCR IN
VCR IN
DVD
DVD
FRONT
+
B : 8 OHMS
L R L R
AUDIO
OUT
LR
VCR
VIDEO
OUT
VCR OUT
VCR OUT
ININOUT
ININOUT
VCR
VCR
FRONT
AUDIO
IN
LR
DSS
DSS
COMPONENT
VIDEO OUT
YC
INPUT
INPUT
1
1
INPUT
2
MONITOR OUT
MONITOR OUT
AUDIO
R
LLR
SURROUND BACK
SPEAKER C/MULTI SPEAKER
SURR.SURR BACK : 6-8 OHMS
VIDEO
OUT IN
B
/ PBCR
Y
TAPE
VIDEO, S-VIDEO , COMPONENT JACKS
VIDEO PROJECTOR
COMPONENT
VIDEO IN
YC
/ PR
B
/ PBCR
/ PR
S-VIDEO
IN
AUDIO
OUT
Satellite Tuner
VIDEO
OUT
S-VIDEO
OUT
DIGITAL
OUT
LR
L R
LR
DSS
MONITOR OUT
DSS
MONITOR OUT
DSS
DSS
LLR
SURROUND BACK
SPEAKER C/MULTI SPEAKER
SURR.SURR BACK : 6-8 OHMS
VIDEO
INPUT
1
INPUT
2
Y
TAPE
AUDIO
R
1
Y
C
R
/
P
R
C
B
/
P
B
OUT
OUT
CD/CDR
R
L
L
SURROUND
SPEAKER SYSTEMS
INPUT
3
Y
C
R
/
P
R
C
B
/
P
B
554
2
221
3
DIGITAL IN
DIGITAL IN
CENTER
Video
S-VIDEO
Analog Audio
L R
IN
Digital Audio (coaxial)
Digital Audio (optical)
COMPONENT
COMPONENT
INPUT
VIDEO
VIDEO
3
1
C
R
/
P
R
C
B
/
P
B
Y
C
R
/
P
R
C
B
/
P
B
Y
C
R
/
P
R
C
B
/
P
B
OUT
CD/CDR
R
L
SURROUND
554
1
221
DIGITAL IN
DIGITAL IN
CENTER
SPEAKER SYSTEMS
3
OUT
L
Video
MONITOR
OUT 2
C
R
/
P
R
C
B
/
P
B
Y
IN
F
OUT
OPT
REMOTE CONT.
DIGITAL OUT
SWITCHED
1.25A 150W
AC OUTLETS
120V 60Hz
(
)
FM
75
GND
ANTENNA
LLSLSLCCSBL
L
R
RRSRSRSWSWSBR
(
)
AUX2
7.1CH INPUT
RS-232C
SL
L
RRSR
PRE OUT
SPEAKER C
OFF
C
SWSWSBR
VIDEO
VIDEO
S-VIDEO
MULTI.
SBL
FRONT A OR B.CENTER.
L R
OUT
FRONT A
TV
TVTVDVD
TV
RRL
FRONT
+
B : 8 OHMS
VCR IN
VCR OUT
ININOUT
VCR
DVD
FRONT
S-VIDEO
L R
AUDIO
OUT
LR
S-VIDEO
IN
Analog Audio
L R
Digital Audio (coaxial)
Digital Audio (optical)
VIDEO
OUT
TV
There are 3 types of video jacks on the rear panel.
VIDEO jack
The video signal for the VIDEO jacks is the conventional composite video signal.
S-VIDEO jack
The video signal is separated into luminance (Y) and color (C) signals for the S-VIDEO jack. The S-VIDEO signals enables high-quality color reproduction. If your video component has an S-VIDEO output, we recommend to use it. Connect the S-VIDEO output jack on your video component to the S-VIDEO input jack on this unit.
Component jack
Make component video connections to a TV or monitor with component inputs to produce higher quality video images. Use a component video cable or 3 video cords to connect the component video out jacks on the unit to the monitor.
Notes:
• Be sure to connect the left and right audio channels properly.
Red connectors are for the R (right) channel, and
white connectors are the for L (left) channel.
• Be sure to connect the inputs and outputs of the video signals properly.
• This unit has the “TV-AUTO ON/OFF” function to turn the TV ON or OFF automatically, by sensing the incoming video signal from the VIDEO jacks.
• You may need to setup the digital audio output format of your DVD player, or other digital source components. Refer to the instructions of the each component connected to the digital input jacks.
• There is no Dolby Digital RF input jack. Use an external RF demodulator with a Dolby Digital decoder to connect the Dolby Digital RF output jack of the DVD player to the digital input jack on this unit.
• The COMPONENT OUTPUT 1 and 2 terminals of the SR5002 can output the same video signal.
• For details concerning the connection of Video equipment, please see VIDEO CONVERT (page
35).
20
R
R
XM
L
L
R
IN
OUT
REMOTE CONT.
OPT
DIGITAL OUT
C
R
/
P
R
C
B
/
P
B
Y
C
R
/
P
R
C
B
/
P
B
Y
1
DIGITAL IN
OUTININ
CD/CDR
OUTININ
TAPE
VCRDVDTV
AUDIO
DSS
NIN
OUT
C
R
/
P
R
C
B
/
P
B
Y
DSSTV DVD R
VCR OUT
MONITOR OUT
MONITOR
OUT 2
INPUT
1
INPUT
2
AC IN
MODEL NO. SR5002
FLASHER
IN
AC OUTLETS
120V 60Hz
SWITCHED
1.25A 150W
CENTER
SURROUND
SURROUND BACK
SPEAKER C/MULTI SPEAKER
SPEAKER SYSTEMS
FRONT A A
SURR.SURR BACK : 6-8 OHMS
1
4
DC
TRIGGER
3
INPUT
3
INPUT 3
OUTPUT
INPUT 2
INPUT 1
HDMI Ver 1.1
COMPONENT
VIDEO
HDMI Ver 1.1
CONNECTING HDMI COMPONENTS
DVD player VIDEO PROJECTOR
HDMI JACK
This unit has 3 HDMI inputs and one HDMI output. It can send digital video and audio signals from DVDs and other sources directly to a display. It minimizes signal degradation caused by analog conversion so that high quality images can be enjoyed. Select an input source from the OSD menu system. (See page 27)
Notes:
• When the HDMI output is connected to a display monitor that does not support HDCP*, signals are not output. To view images in HDMI, it is necessary to connect to a display that supports HDCP*.
• There may be no image output if connected to a TV or display that is not compatible with the above format.
• Refer to the instruction manual of the TV or display to be connected to the unit for detailed information regarding the HDMI terminal.
* HDCP: High-bandwidth Digital Content Protection
CONNECTING HDMI COMPONENTS
An HDMI cable (sold separately) is used to connect the HDMI jack on the unit with the HDMI jack on a DVD player, TV, projector or other component. To transmit multichannel audio via HDMI, the connected player must support multichannel audio transmission through its HDMI jack. HDMI video streaming is compatible with DVI in principle. Therefore, it is possible to connect to a TV or monitor that has a DVI terminal using an HDMI-DVI conversion cable or plug. When connecting to a DVI terminal, connect the audio signal separately.
Notes:
• Some HDMI components can be controlled over the HDMI cable, but this unit cannot control other components this way.
• When connected to a monitor (i.e., TV, projector, etc.) that does not support HDCP, video and audio are not output.
• DVI cables come with 24-pin and 29-pin plugs. This unit supports 24-pin DVI-D cables; 29-pin DVI cables cannot connect to it.
• Some source devices such as DVD players does not support HDMI repeater like those of the unit. In such case, pictures are not properly projected on monitors such as TVs and projectors.
• When multiple components are connected to this unit, turn power to unused components off to prevent interference between them.
• Disconnecting or connecting cables with the power on can damage the equipment. Turn the power off before disconnecting or connecting cables.
• Some DVD-Audio disks disable downmixing. These types of disks are not played back correctly unless the left, center, right and surround left and right speakers, and subwoofer are connected.
• If a DVD player that does not support HDMI 1.1 is connected to the unit, multi channel PCM playback is not possible even with DVD-Audio disks.
If a DVD player or other device with DVI output is
• connected to the unit, a separate audio cable (optical­digital, coaxial digital or analog) is needed for the audio signals. In this case, select the connected audio input as explained in “1 INPUT SETUP”. (See page
27)
• Multi channel PCM signals and audio signals of 64 kHz or higher that are input from the HDMI jack are not output from the DIGITAL OUT jacks.
• Depending on the quiality of the cable used, the HDMI signal may be affected by noise.
• Audio units that use sampling frequencies of 128 kHz and above are not supported.
• When only HDMI components are connected, OSD will not be displayed. (See page 26)
IN
S
.
VCR
VCR OUT
OUT
FRONT
INPUT
INPUT
DSS
MONITOR OUT
DSS
AUDIO
R
LLR
SURROUND BACK
SPEAKER C/MULTI SPEAKER
SURR.SURR BACK : 6-8 OHMS
OUTPUT
HDMI INPUT
ENGLISH
HDMI OUTPUT
HDMI Ver 1.1
B
/
P
B
554
221
DIGITAL IN
COMPONENT
INPUT
VIDEO
3
MONITOR
OUT 2
INPUT 1
C
R
/
P
R
C
B
/
P
B
Y
C
R
/
P
R
3
OPT
DIGITAL OUT
REMOTE CONT.
SWITCHED
1.25A 150W
AC OUTLETS
120V 60Hz
IN
FLASHER
IN
DC
TRIGGER
AC IN
MODEL NO. SR5002
OUT
1
2
Y
TAPE
1
C
Y
C
R
/
P
R
C
B
/
P
B
OUT
OUT
CD/CDR
R
L
SURROUND
L
CENTER
SPEAKER SYSTEMS
INPUT 2
INPUT 3
XM
HDMI Ver 1.1
Satellite Tuner
HDMI OUTPUT
21
ENGLISH
SR
C
SBR
MULTI.
OUT
SBL
L
L
(
AUX2
)
7.1CH INPUT
SBL
SBR
RS-232C
SPEAKER C
OFFONON
R
L
FM
(
75
)
GNDAMAM
ANTENNA
CVCR
DVDTVTV
IN
DVD
VCR IN
S-VIDEO
VIDEO
PRE OUT
FRONT A OR B.CENTER.
FRONT A
+
B : 8 OHMS
FRONT B B
(
AUX2
)
7.1CH INPUT
SBL
SBR
R
L
SR
C
SBR
SBL
L
PRE OUT
R
R
L
L
L
R
IN
OUT
REMOTE CONT.
OPT
DIGITAL OUT
C
R
/
P
R
C
B
/
P
B
Y
C
R
/
P
R
C
B
/
P
B
Y
1
DIGITAL IN
OUTININ
CD/CDR
OUTININ
TAPE
VCRD
AUDIO
DSS
OUT
C
R
/
P
R
C
B
/
P
B
Y
DSSD
VCR IN
VCR OUT
MONITOR OUT
MONITOR
OUT 2
INPUT
1
INPUT
2
AC IN
MODEL NO. SR5002
FLASHER
IN
AC OUTLETS
120V 60Hz
SWITCHED
1.25A 150W
CENTER
SURROUND
SURROUND BACK
SPEAKER C/MULTI SPEAKER
SPEAKER SYSTEMS
FRONT A A
SURR.SURR BACK : 6-8 OHMS
1
4
DC
TRIGGER
3
INPUT
3
INPUT 1
COMPONENT
VIDEO
IN
OUT
REMOTE CONT.
ADVANCED CONNECTING
CONNECTING THE REMOTE CONTROL JACKS
R L R L R L
L
R
FRONT SURR.
DVD Audio player
Super Audio CD Multi
SURR.
BACK
or
channel player
CENTER
SUB
WOOFER
LR
FM
LLSLSLCCSBL
LLSLSLCCSBL
L
L
R
R
RRSRSRSWSWSBR
RRSRSRSWSWSBR
(
(
AUX2
AUX2
L
L
RRSR
RRSR
RL
CONNECTING MULTI CHANNEL AUDIO SOURCE
The 7.1CH INPUT jacks are for multichannel audio source such as a Super Audio CD multichannel player, DVD audio player or external decoder. If you use these jacks, switch on the 7.1CH INPUT and set the 7.1CH INPUT level by using the SETUP MAIN MENU. See page 31.
22
(
)
75
ANTENNA
)
)
7.1CH INPUT
7.1CH INPUT
RS-232C
LR
GND
SPEAKER C
OFF
C
SLSLSBL
C
SLSLSBL
SWSWSBR
SWSWSBR
PRE OUT
PRE OUT
RL RL
VIDEO
S-VIDEO
MULTI.
OUT
FRONT A OR B.CENTER.
FRONT A
R LLRR L R L
TVTVDVD
RRL
VCR IN
IN
V
DVD
Power
Amplifer
L
R
FRONT SURR.
SURR.
BACK
Subwoofer
FRONT
+
B : 8 OHMS
Front
Center
Left
Surround Left
Surround Back Left
Surround
CONNECTING AN EXTERNAL POWER AMPLIFIER
The PREOUT jacks are for connecting external power amplifi ers. Be sure to connect each speaker to the corresponding external power amplifi er.
CENTER
SUB
WOOFER
Front Right
Right
Surround Back Right
VD
VD
L
B BFRONT
CENTER. : 8 OHMS
REMOTE
CONTROL
IN
OUT
VCR IN
ININOUT
VCR
VCR OUT
DSS
MONITOR OUT
DSS
LLR
SURROUND BACK
SPEAKER C/MULTI SPEAKER
SURR.SURR BACK : 6-8 OHMS
INPUT
1
INPUT
2
AUDIO
R
1
Y
C
R
/
P
R
C
B
/
P
B
Y
OUT
OUT
CD/CDR
TAPE
R
L
L
SURROUND
SPEAKER SYSTEMS
COMPONENT
INPUT
VIDEO
3
C
R
/
P
R
C
B
/
P
B
554
221
3
DIGITAL IN
CENTER
REMOTE CONTROL
MONITOR
OUT 2
C
R
/
P
R
C
B
/
P
B
Y
IN
IN
FLASHER
OUT
OPT
OUT
REMOTE CONT.
DIGITAL OUT
REMOTE CONT.
SWITCHED
1.25A 150W
AC OUTLETS
120V 60Hz
IN
OUT
EXTERNAL INTERNAL
q
You can control other Marantz products through this unit with the remote controller by connecting the REMOTE CONTROL terminals on each unit. The signal transmitted from the remote controller is received by the remote sensor on this unit. Then the signal is sent to the connected device through this terminal. Therefore you need to aim the remote signal only to the unit. Also, if a Marantz power amplifi er (some models excluded) is connected to one of these terminals, the power amplifi er’s, power switch is synchronized with this unit’s power switch.
Set the REMOTE CONTROL SWITCH on the back of other units (not the SR4002/SR5002) to “EXT”.(EXTERNAL) to use this feature.
INPUT 1
IN
TRIGGER
AC IN
DVD playerCD recorder CD player
2
REMOTE
CONTROL
RC OUT
OPTION
DC
1
MODE
IN
OUT
EXTERNAL INTERNAL
EXTERNAL INTERNAL
w
Whenever external infrared sensors or similar devices are connected to RC-5 IN of the unit, be sure to always disable operation of the infrared sensor on the unit by using the following procedure.
Hold down the 7.1CH INPUT (SR4002) / MULTI
1.
(SR5002) button and MENU button on the front panel at the same time for fi ve seconds.
The setting “IR=ENABLE” is shown on the FL
2.
DISPLAY.
Press the 1 or 2 cursor button to change this to
3.
“IR=DISABLE”.
Press the ENTER button. Once this setting
4.
is made, the infrared sensor on the unit is disabled.
Note:
Be sure to set to “IR=ENABLE” when external infrared sensors or similar devices are not connected. Otherwise, the unit will be unable to receive remote control commands.
To restore the original setting, perform steps 1
5.
to 4 to set to “IR=ENABLE”.
CONNECTING THE ANTENNA TERMINALS
SR
C
SBR
MULTI.
OUT
SBL
L
R
R
XM
L
L
L
R
IN
OUT
REMOTE CONT.
OPT
DIGITAL OUT
(
AUX2
)
7.1CH INPUT
SBL
SBR
RS-232C
SPEAKER C
OFFONON
R
L
FM
(
75
)
GNDAMAM
C
R
/
P
R
C
B
/
P
B
Y
C
R
/
P
R
C
B
/
P
B
Y
1
ANTENNA
DIGITAL IN
OUTININ
CD/CDR
OUTININ
TAPE
VCR
DVDTVTV
AUDIO
DSS
OUT
C
R
/
P
R
C
B
/
P
B
Y
DSS
DVD
VCR IN
VCR OUT
MONITOR OUT
MONITOR
OUT 2
INPUT
1
INPUT
2
S-VIDEO
VIDEO
AC IN
MODEL NO. SR5002
FLASHER
IN
PRE OUT
AC OUTLETS
120V 60Hz
SWITCHED
1.25A 150W
CENTER
SURROUND
SURROUND BACK
SPEAKER C/MULTI SPEAKER
FRONT A OR B.CENTER.
FRONT A
+
B : 8 OHMS
SPEAKER SYSTEMS
FRONT B B
FRONT A A
SURR.SURR BACK : 6-8 OHMS
1
4
DC
TRIGGER
3
INPUT
3
INPUT 3
OUTPUT
INPUT 2
INPUT 1
HDMI Ver 1.1
COMPONENT
VIDEO
FM
(
75
)
GNDAMAM
ANTENNA
FM External
FM Antenna
(
)
(
)
FM
75
GND
FM
75
GND
ANTENNA
ANTENNA
LLSLSLCCSBL
L
R
RRSRSRSWSWSBR
(
)
AUX2
7.1CH INPUT
RS-232C
SPEAKER C
OFF
C
SLSLSBL
L
RRSR
SWSWSBR
PRE OUT
ASSEMBLING THE AM LOOP ANTENNA
1. Release the vinyl tie and take out the connection
line.
Antenna
VIDEO
S-VIDEO
TVTVDVD
MULTI.
OUT
RRL
FRONT A OR B.CENTER.
FRONT A
INPUT
1
INPUT
2
DSS
VCR IN
VCR OUT
MONITOR OUT
ININOUT
VCR
DVD
FRONT
+
B : 8 OHMS
FRONT
DSS
AUDIO
R
LLR
SURROUND BACK
SPEAKER C/MULTI SPEAKER
SURR.SURR BACK : 6-8 OHMS
AM Loop
Antenna
COMPONENT
INPUT
VIDEO
3
1
C
R
/
P
R
C
B
/
P
B
Y
C
R
/
P
R
C
B
/
P
B
Y
OUT
TAPE
L
554
221
OUT
CD/CDR
R
SURROUND
4. Place the antenna on stable surface.
3
DIGITAL IN
L
CENTER
SPEAKER SYSTEMS
MONITOR
OUT 2
INPUT 1
C
R
/
P
R
C
B
/
P
B
Y
IN
FLASHER
OUT
OPT
IN
TRIGGER
REMOTE CONT.
DIGITAL OUT
AC IN
SWITCHED
1.25A 150W
AC OUTLETS
120V 60Hz
AM External
Antenna
INPUT 2
DC
MODEL NO. SR5002
INPUT 3
XM
HDMI Ver 1.1
CONNECTING THE SUPPLIED ANTENNAS
Connecting the supplied FM antenna
The supplied FM antenna is for indoor use only. During use, extend the antenna and move it in various directions until the clearest signal is received.
ENGLISH
Fix it with push pins or similar implements in the position that will cause the least amount of distortion. If you experience poor reception quality, an outdoor antenna may improve the quality.
Connecting the supplied AM loop antenna
The supplied AM loop antenna is for indoor use only. Set it in the direction and position it to where you receive the clearest sound. Put it as far away as
OUTPUT
possible from the unit, televisions, speaker cables, and power cords. If you experience poor reception quality, an outdoor antenna may improve the quality.
Press and hold down the lever of the AM
1.
antenna terminal.
Insert the bare wire into the antenna terminal.
2.
Release the lever.
3.
CONNECTING AN FM OUTDOOR ANTENNA
Notes:
• Keep the antenna away from noise sources (neon signs, busy roads, etc.).
• Do not put the antenna close to power lines. Keep it well away from power lines, transformers, etc.
• To avoid the risk of lightning and electrical shock, grounding is necessary.
2. Bend the base part in the reverse direction.
3. Insert the hook at the bottom of the loop part
into the slot at the base part.
CONNECTING AN AM OUTDOOR ANTENNA
An outdoor antenna will be more effective if it is stretched horizontally above a window or outside.
Notes:
• Do not remove the AM loop antenna.
• To avoid the risk of lightning and electrical shock, grounding is necessary.
23
ENGLISH
XM
IN
OUT
REMOTE CONT.
OPT
DIGITAL OUT
C
R
/
P
R
C
R
/
P
R
C
B
/
P
B
Y
DIGITAL IN
MONITOR
OUT 2
AC IN
MODEL NO. SR5002
FLASHER
IN
AC OUTLETS
120V 60Hz
SWITCHED
1.25A 150W
N
2
5
DC
TRIGGER
3
INPUT
3
INPUT 3
OUTPUT
INPUT 2
INPUT 1
HDMI Ver 1.1
COMPONENT
VIDEO
XM
XM
XM RADIO OVERVIEW (SR5002 ONLY)
SR5002 is the XM Ready® receiver. You can receive XM Satellite Radio® by connecting to the XM Mini-Tuner and Home Dock (sold separately) and subscribing the XM service.
Introducing XM Satellite Radio
There’s a world of audio listening pleasure beyond AM and FM. XM Satellite Radio which includes:
• Over 170 Digital Channels
• The most commercial-free music in satellite radio
• Live concerts plus exclusive original programming
• The biggest names in news, talk, and entertainment
• The most sports play-by-play
• Major league Baseball. Every team. All season long.
Questions? Visit www.xmradio.com <http://www.xmradio.com/>
How to Subscribe
Listeners can subscribe by visiting XM on the Web at www.xmradio.com or by calling XM’s Listener Care at (800) 967-2346. Customers should have their Radio ID and credit card ready. The Radio ID can be found by selecting channel 0 on the radio. (See the “CHECKING THE XM SIGNAL STRENGTH AND RADIO ID”)
CONNECTING THE XM CONNECT-AND-PLAY ANTENNA
• Plug the XM Mini-Tuner and Home Dock into XM terminal on the rear panel.
• Position the XM antenna near a south-facing window to receive the best signal. When making connections, also refer to the operating instructions of the XM Mini-Tuner and Home Dock.
XMXMXM
5
2
DIGITAL IN
TER
KER
EMS
COMPONENT
INPUT
VIDEO
3
MONITOR
OUT 2
INPUT 1
C
R
/
P
R
C
B
/
P
B
Y
C
R
/
P
R
IN
3
DIGITAL OUT
FLASHER
DC
OUT
OPT
IN
TRIGGER
REMOTE CONT.
AC IN
SWITCHED
1.25A 150W
AC OUTLETS
120V 60Hz
MODEL NO. SR5002
INPUT 2
INPUT 3
HDMI Ver 1.1
XM
XM
OUTPUT
A Warning Against Reverse Engineering
It is prohibited to copy, decompile, disassemble, reverse engineer, or manipulate any technology incorporated in receivers compatible with the XM Satellite Radio system. Furthermore, the AMBE
®
voice compression software included in this product is protected by intellectual property rights including patent rights, copyrights, and trade secrets of Digital Voice Systems, Inc. The user of this or any other software contained in an XM Radio is explicitly prohibited from attempting to copy, decompile, reverse engineer, or disassemble the object code, or in any other way convert the object code into human­readable form. The software is licensed solely for use within this product.
XM $ 12.95 monthly service subscription sold separately. XM Mini-Tuner and Home Dock required to receive XM service (sold separately). Installation costs and other fees and taxes, including a one-time activation fee may apply. Subscription fee is consumer only. All fees and programming subject to change. Channels with frequent explicit language are indicated with an XL. Channle blocking is available for XM radio receivers by calling 1-800-XMRADIO. Subscriptions subject to Customer Agreement available at xmradio.com. XM service only available in the 48 contiguous United States. [XM Ready, XMDirect*] are trademarks of XM Satellite Radio Inc. © 2006 XM Satellite Radio Inc. All rights reserved.
Note
• Keep the power supply cord unplugged until the XM Mini-Tuner and Home Dock connection have been completed.
24
CONNECTING FOR THE MULTI ROOM (SR5002 only)
SR
C
SBR
MULTI.
OUT
SL
SBL
L
R
R
L
L
L
R
POPT
LDIGITAL OUT
(
AUX2
)
7.1CH INPUT
SBL
SBR
RS-232C
SPEAKER C
OFFONON
R
L
FM
(
75
)
GNDAMAM
C
R
/
P
R
C
B
/
P
B
Y
C
B
/
P
BB
Y
1
ANTENNA
DIGITAL IN
OUTININ
CD/CDR
OUTININ
TAPE
VCR
DVDTVTV
AUDIO
DSS
OUT
C
R
/
P
R
C
B
/
P
B
Y
DSS
DVD
VCR IN
VCR OUT
MONITOR OUT
INPUT
1
INPUT
2
S-VIDEO
VIDEO
PRE OUT
CENTER
SURROUND
SURROUND BACK
SPEAKER C/MULTI SPEAKER
FRONT A OR B.CENTER.
FRONT A
+
B : 8 OHMS
SPEAKER SYSTEMS
FRONT B B
FRONT A A
SURR.SURR BACK : 6-8 OHMS
1
4
3
INPUT
3
NCOMPONENT
EVIDEO
MULTI.
OUT
R
L
L
SURROUND BACK
SPEAKER C/MULTI SPEAKER
SURR.SURR BACK : 6-8 OHMS
SR
C
SBR
MULTI.
OUT
SL
SBL
L
R
R
XM
L
L
L
R
IN
OUT
REMOTE CONT.
OPT
DIGITAL OUT
(
AUX2
)
7.1CH INPUT
SBL
SBR
RS-232C
SPEAKER C
OFFONON
R
L
FM
(
75
)
GNDAMAM
C
R
/
P
R
C
B
/
P
B
Y
C
R
/
PRC
B
/
P
B
Y
1
ANTENNA
IDIGITAL IN
OUTININ
CD/CDR
OUTININ
TAPE
VCR
DVDTVTV
AUDIO
DSS
OUT
C
R
/
P
R
C
B
/
P
B
Y
DSS
DVD
VCR IN
VCR OUT
MONITOR OUT
MONITOR
OUT 2
INPUT
1
INPUT
2
S-VIDEO
VIDEO
AC IN
MODEL NO. SR5002
FLASHER
IN
PRE OUT
AC OUTLETS
120V 60Hz
SWITCHED
1.25A 150W
RCENTER
SURROUND
SURROUND BACK
SPEAKER C/MULTI SPEAKER
FRONT A OR B.CENTER.
FRONT A
+
B : 8 OHMS
ESPEAKER MSYSTEMS
FRONT B B
FRONT A A
SURR.SURR BACK : 6-8 OHMS
1
4
DC
TRIGGER
3
INPUT
3
INPUT 3 OUTPUTINPUT 2INPUT 1
HDMI Ver 1.1
COMPONENT
VIDEO
SPEAKER C
OFFONON
L
R
SURROUND BACK
SPEAKER C/MULTI SPEAKER
FRONT A A
SURR.SURR BACK : 6-8 OHMS
SPEAKER C
OFFONON
(Multi room speaker B)
RIGHT
SPEAKER
LEFT
SPEAKER
CONNECTING FOR SPEAKER C USE (SR5002 only)
Bi-amp Connection
A bi-amp connection is possible with speakers that have two sets of inputs (for treble and bass). This allows you to drive the treble and bass units with separate channel amps, which enables better sound quality. Connect the speakers as shown in the fi gure. Set the SPEAKER C selector switch on the rear panel to ON.
Notes:
• If incorrectly connected, a protective circuit in the SR5002 will trip and set the SR5002 to standby. (The STANDBY indicator will fl ash.) In such case, recheck the connections between the speakers and the SR5002.
• Turn power to the SR5002 off before changing the setting of the SPEAKER C selector switch.
ENGLISH
(
)
FM
75
GND
ANTENNA
LLSLSLCCSBL
L
L
R
R
RRSRSRSWSWSBR
(
)
AUX2
7.1CH INPUT
RS-232C
SL
L
RRSR
PRE OUT
SPEAKER C
SWSWSBR
L R
OFF
C
SBL
VIDEO
S-VIDEO
TVTVDVD
MULTI.
MULTI.
OUT
OUT
DVD
RRL
FRONT
FRONT A OR B.CENTER.
+
FRONT A
B : 8 OHMS
VCR IN
ININOUT
VCR
VCR OUT
FRONT
DSS
MONITOR OUT
DSS
LLR
SPEAKER C/MULTI SPEAKER
SPEAKER C/MULTI SPEAKER
SURR.SURR BACK : 6-8 OHMS
SURR.SURR BACK : 6-8 OHMS
INPUT
INPUT
AUDIO
RRL
R
SURROUND BACK
SURROUND BACK
1
2
Y
TAPE
1
Y
C
R
/
P
R
C
B
/
P
B
OUT
OUT
CD/CDR
R
L
SURROUND
L
SPEAKER SYSTEMS
COMPO
INPUT
VID
3
C
B
/
P
Y
C
R
/
P
R
C
B
/
P
B
554
221
3
DIGITAL IN
CENTER
MULTIROOM
MULTIROOM
LEFT
SPEAKER
MULTIROOM
RIGHT
SPEAKER
SPEAKER C
OFF
(
)
FM
75
ANTENNA
LLSLSLCCSBL
L
R
RRSRSRSWSWSBR
(
)
AUX2
7.1CH INPUT
RS-232C
SL
L
RRSR
PRE OUT
VIDEO
S-VIDEO
GND
SPEAKER C
SPEAKER C
OFF
OFF
C
SWSWSBR
MULTI.
OUT
SBL
FRONT A OR B.CENTER.
FRONT A
TVTVDVD
RRL
FRONT
+
B : 8 OHMS
VCR IN
VCR OUT
ININOUT
VCR
DVD
FRONT
FRONT
O
DIGITA
DSS
MONITOR OUT
DSS
AUDIO
R
LLR
RRL
LLR
SURROUND BACK
SURROUND BACK
SPEAKER C/MULTI SPEAKER
SPEAKER C/MULTI SPEAKER
SURR.SURR BACK : 6-8 OHMS
SURR.SURR BACK : 6-8 OHMS
INPUT
1
INPUT
2
TAPE
1
C
B
/
P
B
Y
C
R
/
P
R
C
B
/
P
B
Y
OUT
CD/CDR
R
L
SURROUND
554
221
OUT
DIG
L
CENTE
SPEAK SYSTE
R L
L
FRONT
R
MAIN AMP
(For multiroom)
Note:
You can use surround back speaker terminals as multi room speaker terminals when you use no surround back speaker.
25
ENGLISH
SR
C
SBR
MULTI.
OUT
SBL
L
R
R
XM
L
L
L
R
IN
OUT
REMOTE CONT.
OPT
DIGITAL OUT
(
AUX2
)
7.1CH INPUT
SBL
SBR
RS-232C
SPEAKER C
OFFONON
R
L
FM
(
75
)
GNDAMAM
C
R
/
P
R
C
B
/
P
B
Y
C
R
/
P
R
C
B
/
P
B
Y
1
ANTENNA
DIGITAL IN
OUTININ
CD/CDR
OUTININ
TAPE
VCR
DVDTVTV
AUDIO
DSS
OUT
C
R
/
P
R
C
B
/
P
B
Y
DSS
DVD
VCR IN
VCR OUT
MONITOR OUT
MONITOR
OUT 2
INPUT
1
INPUT
2
S-VIDEO
VIDEO
AC IN
MODEL NO. SR5002
FLASHER
IN
PRE OUT
AC OUTLETS
120V 60Hz
SWITCHED
1.25A 150W
CENTER
SURROUND
SURROUND BACK
SPEAKER C/MULTI SPEAKER
FRONT A OR B.CENTER.
FRONT A
+
B : 8 OHMS
SPEAKER SYSTEMS
FRONT B B
FRONT A A
SURR.SURR BACK : 6-8 OHMS
1
4
DC
TRIGGER
3
INPUT
3
INPUT 3
OUTPUT
INPUT 2
INPUT 1
HDMI Ver 1.1
COMPONENT
VIDEO
RS-232C
FLASHER
IN
DC
TRIGGER
CONNECTING OTHER EQUIPMENT
a ds
VIDEO
GND
SPEAKER C
OFF
C
SLSLSBL
SWSWSBR
PRE OUT
S-VIDEO
TVTVDVD
MULTI.
OUT
RRL
FRONT A OR B.CENTER.
FRONT A
DSS
VCR IN
VCR OUT
MONITOR OUT
ININOUT
VCR
DVD
DSS
LLR
FRONT
+
B : 8 OHMS
FRONT
SPEAKER C/MULTI SPEAKER
SURR.SURR BACK : 6-8 OHMS
(
)
FM
75
ANTENNA
LLSLSLCCSBL
L
R
RRSRSRSWSWSBR
(
)
AUX2
7.1CH INPUT
RS-232C
RS-232C
L
RRSR
a RS232C
Connect an external control device or other device for servicing. (Use a straight cable for the connection.)
s DC OUT (DC TRIGGER)
External devices can be controlled from the SR5002 by connecting them to the DC OUT terminal (12 V). (See page 30)
INPUT
INPUT
AUDIO
R
SURROUND BACK
INPUT 2
HDMI Ver 1.1
INPUT 3
XM
OUTPUT
SPEAKER SYSTEMS
COMPONENT
INPUT
VIDEO
3
C
R
/
P
R
C
B
/
P
B
554
221
3
DIGITAL IN
MONITOR
OUT 2
INPUT 1
C
R
/
P
R
C
B
/
P
B
Y
IN
FLASHER
DC
FLASHER
DC
OUT
OPT
IN
IN
TRIGGER
TRIGGER
REMOTE CONT.
DIGITAL OUT
AC IN
CENTER
SWITCHED
1.25A 150W
AC OUTLETS
120V 60Hz
MODEL NO. SR5002
1
2
TAPE
1
Y
C
R
/
P
R
C
B
/
P
B
Y
OUT
OUT
CD/CDR
R
L
L
SURROUND
d FLASHER IN
This unit can be controlled by connecting a control box or other control device to this unit.
26
SETUP
After all components are connected, initial setup must be performed.
ON SCREEN DISPLAY MENU SYSTEM
This unit incorporates an on-screen menu system, which makes various operations possible by using the cursor (3, 4, 1, 2) and ENTER buttons on the remote control or on the front panel.
Note:
To view the on-screen displays, make certain you have made a connection from the Monitor Out jack on the rear panel to the composite, S-Video, component video input of your TV or projector. (see page20)
1. Press the AMP button of the remote controller.(This step is not needed when operating the setup menus from the unit itself.)
Press the MENU button on the remote controller
2.
or set to display the “SETUP MAIN MENU” of the OSD menu system.
There are 8 items in the SETUP MAIN MENU.
Select a desired sub-menu with the
3.
cursor buttons, and press the ENTER button to enter. The display will change to the selected sub-menu. You can lock the condition of setup to each sub-menu with the buttons.
Note:
If you desire to adjust any sub-menu, you need to set it to UNLOCKED.
If you desire to exit from this menu system,
4.
press the EXIT button, or move the cursor to EXIT and press the ENTER button.
When only HDMI components are connected, the OSD menu will not be displayed on the screen.
1 or 2
3 or 4
or cursor
SETUP MAIN MENU
1. INPUT SETUP :UNLOCK
2. SPEAKER SETUP:UNLOCK
1-1 INPUT SETUP
FUNC:MODE :DIG:HDMI:COMP
-----------------------­TV :AUTO : 5 : - : ­DVD :AUTO : 1 : 1 : 1 VCR :AUTO : 3 : 3 : 3 DSS :AUTO : 2 : 2 : 2 AUX1:AUTO : F : - : -
MAIN NEXT EXIT
* For the SR4002, “–” is displayed for TV DIG
and VCR HDMI.
1-2 INPUT SETUP
FUNC:MODE :DIG:HDMI:COMP
-----------------------­TAPE:AUTO : - : : CD/R:AUTO : 4 : : AUX2:AUTO : - : :
MAIN RETURN EXIT
AUTO SETUP
START CANCEL
SPEAKERS CHECK : SPEAKERS LEVEL : SPEAKERS DISTANCE : SPEAKERS SIZE :
MAIN RETURN NEXT EXIT
2-3 SPEAKERS DISTANCE DISTANCE UNIT : ft FRONT L : 10.0 ft FRONT R : 10.0 ft CENTER : 10.0 ft SURR.L : 10.0 ft SURR.R : 10.0 ft SUB W : 10.0 ft SURR.B L : 10.0 ft SURR.B R : 10.0 ft MAIN RETURN NEXT EXIT
AUTO
2-1 SPEAKER SETUP
SPEAKER SETUP : AUTO
SET MICROPHONE
MAIN NEXT EXIT
2-2 SPEAKERS SIZE
SUBWOOFER : YES FRONT L/R : LARGE CENTER : SMALL SURROUND L/R : SMALL SURR.BACK : 2CH SURR.BACK SIZE : SMALL LPF/HPF : 100Hz BASS MIX : BOTH MAIN NEXT EXIT
2-3 SPEAKERS DISTANCE DISTANCE UNIT : m FRONT L : 3.0 m FRONT R : 3.0 m CENTER : 3.0 m SURR.L : 3.0 m SURR.R : 3.0 m SUB W : 3.0 m SURR.B L : 3.0 m SURR.B R : 3.0 m MAIN RETURN NEXT EXIT
MANUAL
3. PREFERENCE :UNLOCK
4. SURROUND :UNLOCK
5. PLIIx MUSIC :UNLOCK
6. CSII :UNLOCK
7. 7.1 CH. INPUT:UNLOCK
8. MULTI ROOM :UNLOCK EXIT
* “8. MULTI ROOM” is displayed only with
the SR5002.
3 PREFERENCE
STANDBY MODE : ECONOMY TV-AUTO : DISABLE OSD INFO : ENABLE BILINGUAL : MAIN VIDEO CONVERT HDMI : ENABLE DC TRIGGER
MAIN EXIT
* “DC TRIGGER” is displayed only with the SR5002.
3-1 VIDEO CONVERT
TV : ON DVD : ON VCR : ON DSS : ON AUX1 : ON
MAIN RETURN EXIT
SR5002 only
3-2 DC TIRGGER SETUP DC TRIG DISABLE
TV : TAPE : DVD : CD/R : VCR : AUX2 : DSS : TUNER: AUX1 : 7.1CH:
MAIN RETURN EXIT
2-4 SPEAKERS LEVEL TEST MODE : MANUAL FRONT L : 0 dB CENTER : 0 dB FRONT R : 0 dB SURR.R : 0 dB SURR.B R : 0 dB SURR.B L : 0 dB SURR.L : 0 dB SUB W : 0 dB MAIN RETURN EXIT
4 SURROUND
SURR.MODE :AUTO HT-EQ :OFF LFE LEVEL :
MAIN EXIT
5 PLIIx MUSIC PARAMETER
PARAMETER : DEFAULT
PANORAMA : OFF DEMENSION : 0 CENTER WIDTH : 3
MAIN EXIT
6 CSII PARAMETER
TRUBASS : 0 SRS DIALOG : 0
MAIN EXIT
7 7.1 CH. INPUT LEVEL VIDEO-IN : LAST FRONT L : 0 dB CENTER : 0 dB FRONT R : 0 dB SURR.R : 0 dB SURR.B R : 0 dB SURR.B L : 0 dB SURR.L : 0 dB SUB W : 0 dB MAIN EXIT
SR5002 only
8 MULTI ROOM
AUDIO : DVD SLEEP TIMER : OFF MULTI:OUT : STEREO MULTI:OFF MSPK : VOL : VARI LEVEL : -90dB
--- MAIN ROOM STATUS --­VIDEO:DVD AUDIO:DVD MAIN EXIT
ENGLISH
27
ENGLISH
1 INPUT SETUP (ASSIGNABLE DIGITAL INPUT AND COMPONENT VIDEO INPUT)
Use this menu to select the input jack to be assigned to the input source.
Select “INPUT SETUP” in SETUP MAIN
1.
MENU with 3 or 4 cursor button, and press the ENTER button.
1-1 INPUT SETUP
FUNC:MODE :DIG:HDMI:COMP
-----------------------­TV :AUTO : 5 : - : ­DVD :AUTO : 1 : 1 : 1 VCR :AUTO : 3 : 3 : 3 DSS :AUTO : 2 : 2 : 2 AUX1:AUTO : F : - : -
MAIN NEXT EXIT
* For the SR4002, “–” is displayed for TV DIG
and VCR HDMI.
1-2 INPUT SETUP
FUNC:MODE :DIG:HDMI:COMP
-----------------------­TAPE:AUTO : - : : CD/R:AUTO : 4 : : AUX2:AUTO : - : :
MAIN RETURN EXIT
To select the input source and MODE, press
2.
the 3 or 4 cursor buttons.
To select
3.
jack, press the 1 or 2 cursor buttons. Select “AUTO” for input sources, for automatic
detection of the digital input signal condition.
If there is not a digital signal present, but there
is an analog signal present, the analog signal will be played.
Select “DIG”, when only a digital signal will be used. no digital input jacks are used.
To select the vdieo source, select “HDMI” or
4.
COMP” by pressing the 3 or 4 cursor buttons, and press the 1 or 2 cursor buttons to select the vdieo source to be assigned .
After you complete this portion of the set up,
5.
move the cursor to MAIN with the 3 or 4 cursor buttons and press the ENTER button.
DIG
HDMI” or “COMP” for the input
Select “ANA” for input sources for which
Notes:
• When the TUNER is fi xed to the analog input, you can not select any digital input.
• When a DTS-LD or DTS-CD is playing, this setup is not available. This is to avoid noise being generated from the analog input.
• If “AUTO” is selected and a DVD, compact disc or LD is fast-forwarded during playback, decoded signals may produce a skipping sound. In such cases, change the setting to “DIG”.
2 SPEAKER SETUP
After you have installed the unit, connected all the components, and determined the speaker layout, it is now time to perform the settings in the Speaker Setup menu for the optimum sound acoustics for your environment and speaker layout. Before you perform the following settings, it is important that you first determine the following characteristics:
Select “SPEAKER SETUP” in SETUP MAIN
1.
MENU with 3 or 4 cursor button, and press the ENTER button.
2-1 SPEAKER SETUP
Speakers are set up by selecting either MANUAL or AUTO using the 1 and 2 cursor buttons. For operation when AUTO has been selected, see MRAC on page 29.
2-1 SPEAKER SETUP
SPEAKER SETUP : MANUAL
MAIN NEXT EXIT
2-2 SPEAKERS SIZE
When setting the speaker size in the SPEAKER SIZE sub-menu, use the guidelines given below.
LARGE:
The complete frequency range for the channel you are setting will be output from the speaker.
SMALL:
Frequencies of the channel you are setting lower than approx. 100 Hz will be output from the subwoofer. If the Subwoofer is set to “NONE”, the setting of the front speakers will be fi xed to “LARGE,” and the sound will be output from both the left and right speakers.
2-2 SPEAKERS SIZE
SUBWOOFER : YES FRONT L/R : LARGE CENTER : SMALL SURROUND L/R : SMALL SURR.BACK : 2CH SURR.BACK SIZE : SMALL LPF/HPF : 100Hz BASS MIX : BOTH MAIN NEXT EXIT
1. To select the each speaker, press the 3 or 4 cursor buttons.
To select the setting of each speaker size,
2.
press the 1 or 2 cursor buttons.
After you complete this portion of the set up,
3.
move the cursor to “NEXT” with the 3 or 4 cursor buttons and then press the ENTER button to go to the next page.
SUBWOOFER:
YES:
Select when a subwoofer is connected.
NONE:
Select when a subwoofer is not connected.
FRONT L/R
LARGE:
Select if the front speakers are large.
SMALL:
Select if the front speakers are small.
• If “NONE” is selected for the Subwoofer setting, then this setting is fi xed to “LARGE.”
CENTER
NONE:
Select if no center speaker is connected.
LARGE:
Select if the center speaker is large.
SMALL:
Select if the center speaker is small.
SURROUND L/R
NONE:
Select if no surround left and right speakers are connected.
LARGE:
Select if the surround left and right speakers are large.
SMALL:
Select if the surround left and right speakers are small.
SURR. BACK
NONE:
Select if no surround back left and right speakers are connected.
2CH:
Select if the surround back left and right speakers are connected.
1CH:
Select if the one surround back speaker is connected. In this case, the audio signal is emitted form the Surround back L output terminal.
28
Notes:
• If “NONE” is selected for the Surround L/R setting, then this setting is fi xed to “NONE.”
• You can use surround back speaker terminals as multi room speaker terminals when you use no surround back speaker. (See page 22)
SURR. BACK SIZE
LARGE:
Select if the surround back speaker is large.
SMALL:
Select if the surround back speaker is small.
Note:
If “NONE” is selected for the Surround L/R setting, then this setting is not available.
LPF/HPF
When you use a subwoofer, you can select the cutoff frequency for the small speakers used. Select one of the crossover frequency levels according to the size of the small speaker connected.
80Hz 100Hz 120Hz 150Hz 180Hz
Notes:
• If using small front speakers, set a slightly higher frequency. If using large front speakers, set a slightly lower frequency.
• If Pure-Direct mode, 7.1CH Input is in use, this function does not take effect.
BASS MIX
• The bass mix setting is only valid when “LARGE” is set for the front speakers and “YES” is set for the subwoofer during stereo playback .
This setting has effect only during playback of
PCM or analog stereo sources.
• When “BOTH” is selected, the low frequencies will be played through the main L&R, as well as the sub woofer.
In this playback mode, the low frequency range
expand more uniformly through the room, but depending on the size and shape of the room, interference may result in a decrease of the actual volume of the low frequency range.
• By selecting “MIX”, the low frequencies will play through the main L&R ONLY.
Note:
LFE signals during playback of Dolby Digital or DTS, will be played through the sub woofer.
2-3 SPEAKERS DISTANCE
Use this parameter to specify the distance of each speaker’s position from the listening position. The delay time is automatically calculated according to these distances. Begin by determining the ideal or most commonly used seating position in the room. This is important for the timing of the acoustics to create the proper sound space that the unit and today’s sound systems are able to produce.
Note:
For speakers that you have selected “NONE” the Speaker Configuration sub-menu will not appear here. (There are several useful books and special DVD and LD’s available to guide you through proper home theater confi guration. If you are unsure, have your Marantz dealer perform the installation for you. They are trained professionals familiar with even the most sophisticated custom installations. Marantz recommends the WWW.CEDIA.ORG website for further information about this).
2-3 SPEAKERS DISTANCE DISTANCE UNIT : ft FRONT L : 10.0 ft FRONT R : 10.0 ft CENTER : 10.0 ft SURR.L : 10.0 ft SURR.R : 10.0 ft SUB W : 10.0 ft SURR.B L : 10.0 ft SURR.B R : 10.0 ft MAIN RETURN NEXT EXIT
1. To select each speaker , press the 3 or 4 cursor buttons.
To set the distance for each speaker , press the
2.
1 or 2 cursor buttons.
After you complete this portion of the set up,
3.
move the cursor to “NEXT” with the 3 or 4 cursor buttons and then press the ENTER button to go to the next page.
FRONT L:
Set the distance from the front left speaker to your normal listening position.
CENTER:
Set the distance from the center speaker to your normal listening position.
FRONT R:
Set the distance from the front right speaker to your normal listening position.
SURR. L:
Set the distance from the surround left speaker to your normal listening position.
SURR. R:
Set the distance from the surround right speaker to your normal listening position.
SUB W:
Set the distance from the subwoofer to your normal listening position.
SURR. B L:
Set the distance from the surround back left speaker to your normal listening position.
SURR. B R:
Set the distance from the surround back right speaker to your normal listening position.
Notes:
• Set the distance to each speaker in meters (m) or feet (ft) as follows.
m: 0.1 - 9 m in 0.1 m steps ft: 0.3 - 30 ft in 0.3 ft steps
• For the speakers that you have selected “NONE” the Speaker Size menu will not appear.
• The setting for Surr.Back L and Surr.Back R appears if you set for it to, two surround back speakers in the Speaker Size menu.
• The setting of Surr.Back appears if it is set for one surround back speaker in the Speaker Size menu.
2-4. SPEAKERS LEVEL SETTING WITH TEST TONE
Here you will set the volume for each speaker so that they are all heard by the listener at the same level. We recommend using a SPL (Sound Pressure Level) meter, when available.
Note:
The speaker level settings are not available in 7.1 Channel Input mode, CS mode and Multi Channel Stereo mode.
2-4 SPEAKERS LEVEL TEST MODE : MANUAL FRONT L : 0 dB CENTER : 0 dB FRONT R : 0 dB SURR.R : 0 dB SURR.B R : 0 dB SURR.B L : 0 dB SURR.L : 0 dB SUB W : 0 dB MAIN RETURN EXIT
TEST MODE :
Selects “MANUAL” or “AUTO” for generating the mode of the test tone with the 1 or 2 cursor buttons.
If you select “AUTO” , the test tone will be cycled through in a circular pattern which is Left Center Right Surround Right Surround Back Right Surround Back Left Surround Left Subwoofer Left .. increments of 2 seconds for each channel. Using the 1 or 2 cursor buttons, adjust the volume level of the noise from the speaker so that it is the same level for all the speakers.
If you select “MANUAL”, adjust the output level of each speaker as listed below.
When you move the cursor to FRONT L by
1.
pressing the 4 cursor button, the unit will emit a pink noise from the front left speaker.
Remember the level of this noise and then
press the 4 cursor button.
(Note that this can be adjusted to any level
between -10 and +10 dB in 1 dB intervals except the subwoofer setting. The subwoofer can be adjusted to any level between -15 and +10 dB in 1 dB intervals.)
The unit will now emit the pink noise from the
center speaker.
Using the 1 and 2 cursor buttons, adjust the
2.
volume level of the noise from the center speaker so that it is the same level as the front left speaker.
Press the 4 cursor button again. The unit will
3.
now emit the pink noise from the front right speaker.
Repeat steps 2 and 3 above for the front
4.
right and other speakers until all speakers are adjusted to the same volume level.
After you complete this portion of the set up, press the ENTER button, the cursor will move to “MAIN” and then press the ENTER button to go to SETUP MAIN MENU.
Notes:
• Speakers that you selected “NONE” for in the Speaker Size menu will not appear.
• The setting of Surr.Back L and Surr.Back R appears if you have set it for two surround back speakers in the Speaker Size menu.
The setting of Surr.Back appears if you have set it for
• one surround back speaker in the Speaker Size menu.
• To adjust the speaker levels for 7.1-channel input sources, you will need to use the 7.1CH-INPUT sub menu. (See page 31).
ENGLISH
29
ENGLISH
MRAC (Marantz Room Acoustic Calibration)
Speaker settings that were diffi cult by MANUAL setup can now be made by automatically measuring speaker characteristics using the including microphone.
2-1 SPEAKER SETUP
SPEAKER SETUP : AUTO
SET MICROPHONE
MAIN NEXT EXIT
AUTO SETUP
START CANCEL
SPEAKERS CHECK : SPEAKERS LEVEL : SPEAKERS DISTANCE : SPEAKERS SIZE :
MAIN RETURN EXIT
AUTO SETUP
START CANCEL AMBIENT NOISE CHK
SPEAKERS CHECK : SPEAKERS LEVEL : SPEAKERS DISTANCE : SPEAKERS SIZE :
MAIN RETURN EXIT
AUTO SETUP
START CANCEL AMBIENT NOISE OK
&&&&&&&&&&&&&&&&
SPEAKERS CHECK : SPEAKERS LEVEL : SPEAKERS DISTANCE : SPEAKERS SIZE :
MAIN RETURN EXIT
AUTO SETUP
START CANCEL NOW ANALYZING
&&&&&&&&&&&&&&&&
> SPEAKERS CHECK : SPEAKERS LEVEL : SPEAKERS DISTANCE : SPEAKERS SIZE :
MAIN RETURN EXIT
AUTO SETUP
START CANCEL FINISHED
SPEAKERS CHECK : OK SPEAKERS LEVEL : OK SPEAKERS DISTANCE : OK SPEAKERS SIZE : OK
MAIN RETURN NEXT EXIT
NG
NG
NG
AUTO SETUP
START CANCEL MIC SETUP ERROR
SPEAKERS CHECK : SPEAKERS LEVEL : SPEAKERS DISTANCE : SPEAKERS SIZE :
MAIN RETURN NEXT EXIT
AUTO SETUP
START CANCEL AMBI NOISE ERROR
SPEAKERS CHECK : SPEAKERS LEVEL : SPEAKERS DISTANCE : SPEAKERS SIZE :
MAIN RETURN NEXT EXIT
AUTO SETUP
START CANCEL SPEAKER SET ERROR
SPEAKERS CHECK : SPEAKERS LEVEL : SPEAKERS DISTANCE : SPEAKERS SIZE :
MAIN RETURN NEXT EXIT
Measurement
During measurement, a test tone is output from the speakers, which is then measured and analyzed though the microphone. The measurement fl ow and items are as follows. Microphone connection check: MIC CHECK Ambient noise measurement: AMBIENT NOISE Speaker connected/not connected check: SPEAKER CHECK Speaker output level check: SPEAKER LEVEL Distance from speaker (delay time) check: SPEAKER DISTANCE Speaker characteristics check: SPEAKER SIZE
How to Operate
Settings are displayed on the monitor during setup, therefore turn the monitor on.
Connect the included microphone to the MRAC
1.
jack of the unit.
AV SURROUND RECEIVER SR5002
POWER ON/STANDBY
INPUT SELECTOR
SIMPLE
PURE
SURROUND MULTI SPEAKER
MULTI
STANDBY
SETUP MIC
PHONES
SETUP
MEMORY
DISPLAY
DIRECT
MODE
ENTER
AUTO
HT-EQ
EXIT
MENU
BAND
VOLUME
UP
DOWN
CLEAR
T-MODE
ATT
MUTE
AUX 1 INPUT
DIGITAL
RLVIDEO
S-VIDEO
AUDIO
2. Set the microphone at ear height as in the actual listening position. Use a stand or tripod to position the microphone.
Notes:
• Remove any obstructions between the speakers and the microphone.
• Keep the room quiet during measurement.
• The test tone emitted during measurement is loud. Take considerations for neighboring homes and children.
• Step away from the listening position during measurement and operate the unit with the remote controller from outside the speaker path.
• About surround back speakers :
When the surround back speaker is set to NONE in
the SPEAKER SETUP, it is skipped in the AUTO setup. To use the surround back speaker, set it to YES by MANUAL setup before using the MRAC feature.
• The MRAC feature is available except in the following modes.
- 7.1 CH INPUT
- PURE-DIRECT
- SOURCE DIRECT
Select “2. SPEAKER SETUP” on the SETUP
3.
MAIN MENU, then select AUTO for “2­1 SPEAKER SETUP”. Move the cursor to
“NEXT” with the 3 or 4 cursor buttons and then press the ENTER button.
2-1 SPEAKER SETUP
SPEAKER SETUP : AUTO
SET MICROPHONE
MAIN NEXT EXIT
4. Select START on the AUTO SETUP display and press the ENTER button to start measurements.
AUTO SETUP
START CANCEL
SPEAKERS CHECK : SPEAKERS LEVEL : SPEAKERS DISTANCE : SPEAKERS SIZE :
MAIN RETURN NEXT EXIT
5. For measurement items, see “Measurement”.
When measurements are completed,
6.
“FINISHED” appears on the monitor.
Once finished, disconnect the microphone
7.
from the unit.
Measurement results can be seen by selecting
8.
“NEXT” and press the ENTER button or selecting “2. SPEAKER SETUP” on the SETUP MAIN MENU. Then select MANUAL for “2-1 SPEAKER SETUP”.
30
Notes:
• If MRAC is started with both speaker settings A and B off, it will enter CANCEL mode without displaying an ERROR on the screen. When this happens, check the SPEAKER setting.
• The measured speaker distance may differ from the actual distance from speakers. Nevertheless, the measured value is suitable for the speakers.
• To make changes to individual speakers, select 2. SPEAKER SETUP on the SETUP MAIN MENU, then select MANUAL for 2-1 SPEAKER SETUP.
• The included microphone is designed specifi cally for this receiver. Other microphones do not guarantee suitable measurement results. Use the included microphone to conduct measurements.
• During measurement, press the ENTER or EXIT button to cancel measurement.
• In some rooms, an error may occur during auto speaker setup or it may not be possible to set Speaker distance correctly because of room acoustics. In such case, set the speaker distance by MANUAL setup.
• Please set any THX Certifi ed speakers manually to “Small” and the crossover to “80 Hz” after Auto setup operation.
• When only HDMI components are connected, OSD will not be displayed.
Error Indications During Measurement
If trouble occurs during measurement, an error message is displayed on the monitor screen and FL display. Those errors and their remedies are described below. The message appearing on the FL display is given in ( ).
MIC SETUP ERROR (MIC SET ERROR) The microphone (MC-10) is not properly connected.
Check the microphone connection. AMBI NOISE ERROR (AMBI NOISE ER) Measurement cannot be done correctly because of
excessive ambient noise. Either temporarily turn off power to noisy
devices such as air conditioning or move them
out of the room. Retry measurement when the room is quiet.
SPEAKER SET ERROR (SPK SET ERROR) The speakers are not properly connected.
Recheck speaker layout and connections.
3 PREFERENCE
3 PREFERENCE
STANDBY MODE : ECONOMY TV-AUTO : OSD INFO : ENABLE
VIDEO CONVERT HDMI : ENABLE DC TRIGGER
MAIN EXIT
1. Select “PREFERENCE” in the SETUP MAIN MENU with the 3 or 4 cursor buttons, and press the ENTER button.
To select a desired content, press the 3 or 4
2.
cursor buttons.
STANDBY MODE:
When this function is set to “ECONOMY”, you can reduce the power consumption when the unit is in the standby mode.
Note:
TV-AUTO and RS-232C are disabled in the “ECONOMY” setting (SR5002 only).
TV AUTO:
Select the TV AUTO ON/OFF function to enable or disable with the 1 or 2 cursor buttons.
OSD Info:
Select the OSD information function to enable or disable with the 1 or 2 cursor buttons. If you select “ENABLE”, the unit will display the status of the feature (Volume up/down, input select, etc..) on the TV monitor. But if you do not desire this information, select “DISABLE”.
VIDEO CONVERT:
Select the VIDEO CONVERT function to enable or disable with the 1 or 2 cursor buttons. (Video cable connection: Refer to page 20)
3-1 VIDEO CONVERT
TV : ON DVD : ON VCR : ON DSS : ON AUX1 : ON
MAIN RETURN EXIT
After you complete this portion of the set up, move the cursor to “MAIN” with the 3 or 4 cursor buttons and press the
ENTER
button.
HDMI AUDIO:
This setting determines whether to playback audio input to the HDMI jacks through the unit or output it through the unit to a TV or projector. ENABLE: The audio input to the HDMI jacks
can be played back by this unit. In such case, audio signals are not output to the TV or projector.
THROUGH: The audio input to the HDMI jacks
is not output from the speaker terminals of the unit. Audio data is output directly to the TV or projector. This setting is used to listen to audio on a multi channel TV, etc.
DC TRIGGER:
Select “DC TRIG SETUP” in the SETUP MAIN MENU with 3 or 4 cursor button, and press the ENTER button.
3-2 DC TIRGGER SETUP DC TRIG DISABLE
TV : TAPE : DVD : CD/R : VCR : AUX2 : DSS : TUNER: AUX1 : 7.1CH:
MAIN RETURN EXIT
You can select MAIN ROOM, MULTI ROOM, REMOTE or DISABLE by pressing 1 or 2 cursor buttons.
Notes:
• REMOTE is available for the external control. The RC5001SR cannot operate this function.
• To select desired input source , press 3 or 4 cursor button.
• To set ON or OFF, press 1 or 2 cursor button.
• After you complete this portion of the set up, move the cursor to “MAIN” with the 3 or 4 cursor buttons and press the ENTER button.
4 SURROUND
4 SURROUND
SURR.MODE :AUTO HT-EQ :OFF LFE LEVEL :
MAIN EXIT
1. Select “SURROUND” in the SETUP MAIN MENU with the 3 or 4 cursor buttons, and press the ENTER button.
To select a desired content , press the 3 or 4
2.
cursor buttons.
SURR.MODE:
Select the desired surround mode with the 1 or 2 cursor buttons.
HT-EQ:
Select to active the HT-EQ with the buttons. The tonal balance of a film soundtrack will be excessively bright and harsh when played back over audio equipment in the home. This is because fi lm soundtracks were designed to be played back in large movie theater environments. Activating the HT-EQ feature when watching a fi lm made for movie theaters corrects this and restores the correct tonal balance. The HT-EQ feature is available except in the following modes.
• 7.1 CH INPUT
• PURE-DIRECT
• SOURCE DIRECT
• When VIRTUAL is set for the surround mode
LFE LEVEL:
Select the output level of the LFE signal included in the Dolby Digital signal or the DTS signal. Select 0 dB, -10 dB or OFF with the 1 or 2 cursor buttons.
After you complete this portion of the set up, move the cursor to “MAIN” with the 3 or 4 cursor buttons and press the ENTER button.
1 or 2
cursor
ENGLISH
31
ENGLISH
5 PL II (PRO LOGIC II) MUSIC PARAMETER
Pro Logic II -Music mode creates a rich and enveloping surround ambience from stereo sources such as CDs. In this mode, SR4002/SR5002 includes three controls to fi ne-tune the soundfi eld as follows.
5 PLIIx MUSIC PARAMETER
PARAMETER : DEFAULT
PANORAMAA : OFF DIMENSION : 0 CENTER WIDTH : 3
MAIN EXIT
Select “PL II MUSIC” in the SETUP MAIN MENU with the 3 or 4 cursor buttons, and press the ENTER button.
PARAMETER:
Select “DEFAULT” or “CUSTOM” with the 1 or 2 cursor buttons. If you select “CUSTOM”, you can adjust three parameters as listed below.
PANORAMA:
Select the Panorama mode On or Off with the 1 or 2 cursor buttons. Panorama wraps the sound of the front left and right speakers around you, for an exciting perspective.
DIMENSION:
Set the Dimension level between +3 and –3 level in 1 level intervals with the 1 or 2 cursor buttons. Adjust the soundfi eld either towards the front or towards the rear. This can be useful to help achieve a more suitable balance from all the speakers with certain recordings.
CENTER WIDTH:
Set the Center width level between 0 and 7 in 1 level intervals with the 1 or 2 cursor buttons. Center Width allows you to gradually spread the center channel sound into the front left and right speakers. At its widest setting, all the sound from the center is mixed into the left and right. This control may help achieve a more spacious sound or a better blend for the front image. If “NONE” was selected for the Center speaker setting, in the Speaker size set up menu, then this setting will not appear.
After you complete this portion of the set up, move cursor to “MAIN” with the 3 or 4 cursor buttons and press the ENTER button.
32
6 CS II (CIRCLE SURROUND II) PARAMETER
6 CSII PARAMETER
TRUBASS : 0 SRS DIALOG : 0
MAIN EXIT
1. Select “CS II” in the SETUP MAIN MENU with the 3 or 4 cursor buttons, and press the ENTER button.
To Select desired contents as below, press the
2.
3 or 4 cursor buttons.
TRUBASS:
Set the TRUBASS level between 0 and 6 level in 1 level interval with the 1 or 2 cursor buttons. TRUBASS produced by the speakers are an octave below the actual physical capabilities of the speakers adding exciting, deeper bass effects.
SRS DIALOG:
Set the SRS DIALOG level between 0 and 6 in 1 level intervals with the 1 or 2 cursor buttons. This can be popped out of the surround audio effects, allowing the listener to easily discern what the actors say. If “NONE” was selected for the Center speaker setting, in the Speaker size set up menu, then this setting will not appear.
After you complete this portion of the set up, move cursor to “MAIN” with the 3 or 4 cursor buttons and press the
ENTER
button.
7 7.1 CH INPUT LEVEL
This sub-menu is to adjust the speaker levels for 7.1­channel input sources. Here you will adjust the volume for each channel so that they are all heard by the listener at the same level.
7 7.1 CH. INPUT LEVEL VIDEO-IN : LAST FRONT L : 0 dB CENTER : 0 dB FRONT R : 0 dB SURR.R : 0 dB SURR.B R : 0 dB SURR.B L : 0 dB SURR.L : 0 dB SUB W : 0 dB MAIN EXIT
1. Select “7.1CH INPUT” in the SETUP MAIN MENU with the 3 or 4 cursor buttons, and press the ENTER button.
To select “VIDEO IN”, press 3 or 4 cursor
2.
button.
Using the 1 or 2 cursor buttons, select the
3.
video input source which is emitted from Monitor out in the 7.1 CH INPUT function.
The input source is switched by pressing the
1 or 2 cursor buttons as follows;
LAST ↔ TV ↔ DVD ↔ VCR ↔ DSS ↔ AUX1
V-OFF LAST
Notes:
When select LAST, the source is set previous source
• before 7.1 CH INPUT function
When select V-OFF, no signal is emitted from monitor
• out terminal.
4. To Select desired channel , press the 3 or 4 cursor buttons.
Using the 1 or 2 cursor buttons, adjust the
5.
volume level of each channel.
After you complete this portion of the set up,
6.
move the cursor to “MAIN” with the 3 or 4 cursor buttons and press the ENTER button.
Notes:
These settings will be memorized to 7.1CH INPUT
• source.
• This feature can be directly selected with the CH.SEL button of the remote controller.
is activated.
8 MULTI ROOM (SR5002 only)
SR5002 has features in MULTI ROOM SYSTEM such as source selector, sleep timer, Multi Room Speaker output and remote control. You can set these feature in this sub-menu.
8 MULTI ROOM
AUDIO : DVD SLEEP TIMER : OFF MULTI:OUT : STEREO MULTI:OFF MSPK : VOL : VARI LEVEL : -90dB
--- MAIN ROOM STATUS --­VIDEO:DVD AUDIO:DVD MAIN RETURN EXIT
1. SelectMULTI ROOM” in the SETUP MAIN MENU with 3 or 4 cursor button, and press the ENTER button.
To Select desired contents, press 3 or 4 cursor
2.
button
AUDIO:
Select the audio source of the Multi-room output with 1 or 2 cursor buttons.
SLEEP TIMER:
SLEEP timer function is available during the multiroom is active, set the time with 1 or 2 cursor buttons.
MULTI OUT:
To switch MULTI and MSPK outputs to either STEREO or MONO, press 1 or 2 cursor button.
MULTI (MULTI ROOM):
To switch on the Multi-room output ON or OFF, press 1 or 2 cursor button.
VOL (VOLUME SETUP):
Select whether the Multi-room output level is variable or fi xed with a 1 or 2 cursor buttons.
LEVEL (VOLUME LEVEL):
Adjust the Multi-room output level with 1 or 2 cursor buttons.
MSPK (MULTI SPEAKER):
To switch on the Multi-speaker output ON or OFF, press 1 or 2 cursor buttons.
Note:
This setting can be changed when the Surr Back is set “NONE” in 2-1 SPEAKER SIZE menu. When this setting is unavailable, “✽✽✽” is displayed
MAIN ROOM STATUS:
Selected input source in the main room will be displayed.
Note:
If “VOLUME” is set to “FIXED”, the multi-room output level cannot be adjusted from the second zone.
After you complete this portion of the set up, move the cursor to “MAIN” with 3 or 4 cursor buttons and press ENTER button.
SIMPLE SETUP
You can setup the speaker conditions quickly with SIMPLE SETUP menu. In this menu, the number of speakers and speaker delay time can be set. These settings can be changed more detail in “2. SPEAKER” setup menu. Press the SIMPLE SETUP button on the unit to enter this menu.
3. 5.1. 2. 4.
AV SURROUND RECEIVER SR5002
POWER ON/STANDBY
INPUT SELECTOR
SIMPLE
PURE
SURROUND
MULTI
SPEAKER
MULTI
STANDBY
SETUP MIC
PHONES
SETUP
DIRECT
MODE
AUTO
HT-EQ
MENU
MEMORY
DISPLAY
ENTER
CLEAR
T-MODE
EXIT
BAND
VOLUME
DOWN
DIGITAL
UP
ATT
MUTE
AUX 1 INPUT
RLVIDEO
S-VIDEO
AUDIO
The relation of the speakers number and conectted speaker
CHANNEL
Front
L/R (F)
Front
Center
(C)
Surround
L/R (S)
Surround Back L/R
(SB)
7.1 ch LARGE SMALL SMALL 2ch YES
7.0 ch LARGE SMALL SMALL 2ch NONE
6.1 ch LARGE SMALL SMALL 1ch YES
6.0 ch LARGE SMALL SMALL 1ch NONE
5.1 ch LARGE SMALL SMALL NONE YES
5.0 ch LARGE SMALL SMALL NONE NONE
4.1 ch LARGE NONE SMALL NONE YES
4.0 ch LARGE NONE SMALL NONE NONE
3.1 ch LARGE SMALL NONE NONE YES
3.0 ch LARGE SMALL NONE NONE NONE
2.1 ch LARGE NONE NONE NONE YES
2.0 ch LARGE NONE NONE NONE NONE
Sub
woofer
(SW)
ENGLISH
1. Press the SIMPLE SETUP button on the unit to enter the “SPEAKERS” menu.
Press 1 or 2 cursor button to select the speaker
2.
number.
Press the 4 cursor button to enter the “ROOM”
3.
menu.
Press 1 or 2 cursor button to select the room
4.
size. After fi nishing all setup, press the 4 cursor
5.
button to exit the SIMPLE SETUP menu.
Note:
All Simple Setup menu is reset when the speaker setting is changed with Speaker Setup menu.
SIMPLE SETUP
1.SPEAKERS : ?
2.ROOM : ?
MAIN RETURN EXIT
The relation of the room size and fl oor space
Floor
Width
SIZE
space
(W)
Depth
(D)
Imaging Distance
Front (F) 6 ft. (1.8 m)
Center (C) 5 ft. (1.5 m)
SMALL 10 m22.7 m 3.6 m
Surround (S) 4 ft. (1.2 m)
Surr. Back (SB) 5 ft. (1.5 m)
Sub Woofer (SW) 5 ft. (1.5 m)
Front (F) 7 ft. (2.1 m)
Center (C) 6 ft. (1.8 m)
Surround (S) 5 ft. (1.5 m)
MEDIUM 16 m
2
3.6 m 4.5 m Surr. Back (SB) 7 ft. (2.1 m)
Sub Woofer (SW) 6 ft. (1.8 m)
Front (F) 9 ft. (2.7 m)
Center (C) 8 ft. (2.4 m)
Surround (S) 7 ft. (2.1 m)
LARGE 24 m
2
4.5 m 5.4 m Surr. Back (SB) 8 ft. (2.4 m)
Sub Woofer (SW) 8 ft. (2.4 m)
The relation of the room size and fl oor space is a roughly standard.
33
ENGLISH
OFFONSET
SOURCE
I
34
BASIC OPERATION
(PLAYBACK)
SELECTING AN INPUT SOURCE
Before you can listen to any input media, you must fi rst select the input source on the unit.
Example : DVD
AUDIO
ANGLE
SUB TITLE
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
SIMPLE
PURE
SURROUND
POWER ON/STANDBY
MULTI
SPEAKER
MULTI
STANDBY
SETUP MIC
PHONES
SETUP
DIRECT
MODE
AUTO
HT-EQ
MENU
To select DVD, turn the INPUT SOURCE knob on the front panel or simply press the DVD button on the remote controller. After you have selected DVD, simply turn on the DVD player and play the DVD.
• As the input source is changed, the new input name will appear momentarily an OSD information on the video display. The input name will also appear in the display, on the front-panel.
• As the input is changed, this unit will automatically switch to the digital input, surround mode, attenuation, and night mode status which were entered during the confi guration process for that source.
• When an audio source is selected, the last video input used remains routed to the VCR Output and Monitor Output. This permits simultaneous viewing and listening to different sources.
• When a Video source is selected, the video signal for that input will be routed to the Monitor Output jacks and will be viewable on a TV monitor connected to the unit.
If a component video input is connected to the
DVD or DSS component inputs, it will be routed to the Component Video Output. Make certain that your TV is set to the proper input to view the signal.
DISC+
CH-SEL
BASS
TV
TUNER
TAPE
REMOTE CONTROLLER
V-OFF
DVD VCR
CD
AUX1
ATT.
TREBLE
DSS
MD
CDR
AMP
AUX2
SELECTING THE SURROUND MODE
Example: AUTO SURROUND
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
SIMPLE
PURE
SURROUND
POWER ON/STANDBY
MULTI
SPEAKER
MULTI
STANDBY
SETUP MIC
PHONES
SETUP
DIRECT
MODE
AUTO
HT-EQ
MENU
To select the surround mode during playback, press the SURROUND MODE button on the front panel or the SURROUND MODE buttons on the remote controller.
l/
P.DIRECT
SLEEP
DISPLAY
dts
AUTO
123
EX/ES
VIRTUAL
CS
456
STEREO
NIGHT
M-CH ST
789
7.1CH IN
A/D
SURROUND
LIP SYNC/ INPUT
T.MODE
P.SCAN
HT-EQ
NIGHT MODE
LIP SYNC/
INPUT
dts
AUTO
123
CS
456
M-CH ST
789
CL
CAT
CH/
Press the NIGHT button on the remote controller to turn on the NIGHT mode. Selecting the Night Mode ON is effective in Dolby Digital only, and it compresses the dynamic range. This softens loud passages such as sudden explosions, to help prevent disturbing others late at night. To turn off the Night mode, press the NIGHT button again.
EX/ES
STEREO
7.1CH IN
SPKR A/B
T.MODE
VIRTUAL
P.SCAN
NIGHT
HT-EQ
A/D
MEMO
0
+10
VOLUME
MUTE
ADJUSTING THE MAIN VOLUME
SPKR A/B
HT-EQ
A/D
MEMO
0
+10
VOLUMEVOLUME
MUTE
CAT
M-SPKR
MENU
ENTER
VOLUME
DOWN
PLAY
CLEAR
MEMORY
T-MODE
XIT
BAND
DIGITAL
UP
ATT
MUTE
AUX 1 INPUT
RLVIDEO
S-VIDEO
AUDIO
7.1CH IN
CL
CAT
CH/
MULTI/
INFO
Adjust the volume to a comfortable level using the VOLUME control knob on the front panel or VOLUME 3 / 4 buttons on the remote controller. To increase the volume, turn the VOLUME knob clockwise or press VOLU ME 3 button on the remote controller, to decrease the volume, turn counterclockwise or press VOLUME 4 button on the remote controller.
Notes:
• The volume can be adjusted within the range of –
to 18 dB, in steps of 1 dB.
However, when the channel level is set as described
• on page 26, if the volume for any channel is set at +1 dB or greater, the volume cannot be adjusted up to 18 dB.
(In this case the maximum volume adjustment range is
“18 dB - Maximum value of channel level)
ADJUSTING THE TONE (BASS & TREBLE) CONTROL
TUNING
PRESET
-
-
++
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
BASSBASS
TREBLETREBLE
DVD
VCR
TV
TUNER
TAPE
REMOTE CONTROLLER
During a listening session you may wish to adjust the Bass and Treble Control to suit your listening tastes or room acoustics.
(Using the remote controller)
To adjust the bass effect, press BASS 3 or BASS 4 on the remote controller. To adjust the treble effect, press TREBLE 3 or TREBLE 4 on the remote controller.
Note:
The tone control function can work in the AUTO Surround, Stereo, Dolby PL Multi Ch. Stereo mode.
DSS
MD
CDR
CD
AMP
AUX2
AUX1
II x
, DTS, DTS-ES, and
TEMPORARILY TURNING OFF THE SOUND
VOLUME
DOWN
SPLAY
CLEAR
MEMORY
T-MODE
EXIT
BAND
DIGITAL
UP
ATT
MUTE
AUX 1 INPUT
RLVIDEO
S-VIDEO
AUDIO
7.1CH IN
CL
CAT
CH/
SPKR A/B
MULTI/
INFO
To temporarily silence all speaker outputs such as when interrupted by a phone call, press the MUTE button on the front panel or MUTE button on the remote controller. This will interrupt the output to all speakers and the head-phone jack, but it will not affect any recording or dubbing that may be in progress. When the system is muted, the display will show “MUTE” . Press the MUTE button again to return to normal operation.
HT-EQ
A/D
MEMO
0
+10
VOLUME
MUTEMUTE
CAT
M-SPKR
MENU
ENTER
USING THE SLEEP TIMER
SEND
LEARN
SOURCE
SLEEPSLEEP
AUTO
To program this unit for automatic standby, press the SLEEP button on the remote controller. Each press of the button will increase the time before shut down in the following sequence.
OFF 10 20 30 50
120 90 80 70 60100110
The sleep time will be shown for a few seconds in the display on the front panel, and it will count down until the time has elapsed. When the programmed sleep time has elapsed, the unit will automatically turn off. Note that the SLEEP indicator on the display will illuminate when the Sleep function is programmed. To cancel the Sleep function, press the SLEEP button until the display shows “SLEEP OFF” and the SLEEP indicator will disappear.
OFFONSET
l/
P.DIRECT
DISPLAY
dts
123
EX/ES
VIRTUAL
CS
456
SURROUND
LIP SYNC/ INPUT
T.MODE
40
VIDEO CONVERT
When this function is activated, the video or S-video signal can be emitted from the video, S-video or component video output terminal. To activate this function, select VIDEO CONVERT in PREFERENCE menu and set ENABLE.
Notes:
• The component video signal is emitted only from component video output terminal.
When the video equipment is connected by
component terminal, connect the monitor and SR4002/SR5002 by the component terminal.
• This function is unavailable for the REC out terminal.
This function is unavailable for the still picture, fast
• forward and reverse playing of the video component.
• If, while attempting to use the video convert feature, the SR4002/SR5002 cannot synchronize with the display device, “NO SIGNAL” appears on the monitor, or noise is generated, this feature cannot be used. All of these signs are caused by equipment incompatibility; there is nothing wrong with the SR4002/SR5002.
In such case, set VIDEO CONVERT in the PREFERENCE menu to DISABLE. Also, connect the video input signal to the display device via the MONITOR OUT terminal under VIDEO and the S-video input signal to the display device via the MONITOR OUT terminal under S-VIDEO.
Example:
Monitor is connected with the component.
SR5002 only
Monitor is connected with the video or S-video.
SR5002 only
Monitor is connected with the video or component.
SR4002/SR5002
S-VIDEO VIDEO
SR4002/SR5002
VIDEO
VIDEO
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
PURE
SURROUND MODE
MULTI
DIRECT
SPEAKER
MULTI
STANDBY
AUTO
HT-EQ
PHONES
POWER ON/STANDBY
SETUP MIC
VOLUME
UP
DOWN
SIMPLE SETUP
MEMORY
DISPLAY
CLEAR
ATT
MUTE
ENTER
T-MODE
EXIT
MENU
BAND
AUX 1 INPUT
DIGITAL
RLVIDEO
S-VIDEO
AUDIO
component
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
PURE
SURROUND MODE
MULTI
DIRECT
SPEAKER
MULTI
STANDBY
AUTO
HT-EQ
PHONES
POWER ON/STANDBY
SETUP MIC
VOLUME
UP
DOWN
SIMPLE SETUP
MEMORY
DISPLAY
CLEAR
ATT
MUTE
ENTER
T-MODE
EXIT
MENU
BAND
AUX 1 INPUT
DIGITAL
RLVIDEO
S-VIDEO
AUDIO
S-VIDEO
AV SURROUND RECEIVER SR4002
INPUT SELECTOR
PURE
SURROUND
DIRECT
MODE
S.SPEAKER B
7.1 CH INPUT
STANDBY
AUTO
HT-EQ
PHONES
SETUP MIC
POWER ON/STANDBY
VOLUME
UP
DOWN
SIMPLE SETUP
MEMORY
DISPLAY
CLEAR
ATT
MUTE
ENTER
T-MODE
EXIT
MENU
BAND
AUX 1 INPUT
DIGITAL
RLVIDEO
S-VIDEO
AUDIO
component
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
PURE
SURROUND
MODE
MULTI
DIRECT
SPEAKER
MULTI
STANDBY
AUTO
HT-EQ
PHONES
POWER ON/STANDBY
SETUP MIC
VOLUME
UP
DOWN
SIMPLE SETUP
MEMORY
DISPLAY
CLEAR
ATT
MUTE
ENTER
T-MODE
EXIT
MENU
BAND
AUX 1 INPUT
DIGITAL
RLVIDEO
S-VIDEO
AUDIO
HDMI
AV SURROUND RECEIVER SR5002
HDMI
INPUT SELECTOR
PURE
SURROUND MODE
MULTI
DIRECT
SPEAKER
MULTI
STANDBY
AUTO
HT-EQ
PHONES
POWER ON/STANDBY
SETUP MIC
VOLUME
UP
DOWN
SIMPLE SETUP
MEMORY
DISPLAY
CLEAR
ATT
MUTE
ENTER
T-MODE
EXIT
MENU
BAND
AUX 1 INPUT
DIGITAL
RLVIDEO
S-VIDEO
AUDIO
VIDEO
S-VIDEO
component
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
PURE
SURROUND MODE
MULTI
DIRECT
SPEAKER
MULTI
STANDBY
AUTO
HT-EQ
PHONES
POWER ON/STANDBY
SETUP MIC
VOLUME
UP
DOWN
SIMPLE SETUP
MEMORY
DISPLAY
CLEAR
ATT
MUTE
ENTER
T-MODE
EXIT
MENU
BAND
AUX 1 INPUT
DIGITAL
RLVIDEO
S-VIDEO
AUDIO
VIDEO
S-VIDEO
HDMI
component
Notes of OSD menu:
HDMI: OSD menu is not displayed. VIDEO/S-VIDEO/component: VIDEO CONVERT of HDMI is not possible, thus the OSD menu is not displayed.
ENGLISH
VIDEO
component
S-VIDEO
The signal cannot be converted from the component to the video or S-video.
Notes of OSD menu:
• The setup menu can be displayed through all video out (COMPONENT, S-VIDEO, VIDEO).
• The setting informations (e.g. volume setting) are displayed through all video out when the VIDEO CONVERT function are set ON.
Note:
No setting information is displayed when the signal is emitted from the COMPONENT IN to COMPONENT OUT.
• The setting informations (e.g. volume setting) are displayed through the S-VIDEO or VIDEO out when the VIDEO CONVERT function are set DISABLE. When the S-VIDEO and VIDEO outputs are used simultaneously, the setting informations are displayed through the S-VIDEO out only.
35
ENGLISH
SURROUND MODE
This unit is equipped with many surround modes. These are provided to reproduce a variety of surround sound effects, according to the content of the source to be played. The available surround modes may be restricted depending on the input signal and speaker setup.
The relation between the selected surround mode and the input signal
The surround mode is selected with the surround mode selector on this unit or the remote controller. However, the sound you hear is subject to the relationship between the selected surround mode and input signal. That relationship is as follows;
Surround Mode
AUTO Dolby Surr. EX Dolby Digital EX OOOOO2 DIGITAL EX L, C, R, SL, SR, S, LFE
SOURCE DIRECT PURE DIRECT
EX/ES Dolby Surr. EX Dolby Digital EX OOOOO2 DIGITAL EX L, C, R, SL, SR, S, LFE
DOLBY (PL IIx movie) (PL IIx music) (PL IIx game) (Pro Logic)
DTS (Neo:6 Cinema) (Neo:6 Music)
Input Signal Decoding
Dolby D (5.1ch) Dolby Digital 5.1 OOO - O2 DIGITAL L, C, R, SL, SR, LFE Dolby D(2ch) Dolby Digital 2.0 O ----2 DIGITAL L, R Dolby D (2ch Surr) Pro Logic IIx movie OOOOO2 DIGITAL , 2 SURROUND L, R, S DTS-ES DTS-ES OOOOOdts, ES L, C, R, SL, SR, S, LFE DTS 96/24 DTS 96/24 OOO - O dts 96/24 L, C, R, SL, SR, LFE DTS (5.1ch) DTS 5.1 OOO - O dts L, C, R, SL, SR, LFE Multi Ch-PCM Multi Ch-PCM OOO - O PCM L, C, R, SL, SR, LFE Multi Ch-PCM 96kHz Multi Ch-PCM 96kHz OOO - O PCM L, C, R, SL, SR, LFE PCM(Audio) PCM (Stereo) O ---O PCM L, R PCM 96kHz PCM (96kHz Stereo) O ---O PCM L, R HDCD PCM (Stereo) O ---O PCM HDCD L, R Analog Stereo O ---O ANALOG - Dolby Surr. EX Dolby Digital EX OOOOO2 DIGITAL EX L, C, R, SL, SR, S, LFE Dolby D (5.1ch) Dolby Digital 5.1 OOO - O2 DIGITAL L, C, R, SL, SR, LFE Dolby D (2ch) Dolby Digital 2.0 O ----2 DIGITAL L, R Dolby D (2ch Surr) Pro Logic IIx movie OOO --2 DIGITAL , 2 SURROUND L, R, S DTS-ES DTS-ES OOOOOdts, ES L, C, R, SL, SR, S, LFE DTS 96/24 DTS 96/24 OOO - O dts 96/24 L, C, R, SL, SR, LFE DTS (5.1ch) DTS 5.1 OOO - O dts L, C, R, SL, SR, LFE Multi Ch-PCM Multi Ch-PCM OOO - O PCM L, C, R, SL, SR, LFE Multi Ch-PCM 96kHz Multi Ch-PCM 96kHz OOO - O PCM L, C, R, SL, SR, LFE PCM (Audio) PCM (Stereo) O - - - - PCM L, R PCM 96kHz PCM (96kHz Stereo) O - - - - PCM L, R HDCD PCM (Stereo) O - - - - PCM HDCD L, R Analog Stereo O - - - - ANALOG -
Dolby D (5.1ch) Dolby Digital EX OOOOO2 DIGITAL L, C, R, SL, SR, LFE DTS-ES DTS-ES OOOOOdts , ES L, C, R, SL, SR, S, LFE DTS 96/24 DTS-ES OOOOOdts 96/24 L, C, R, SL, SR, LFE DTS(5.1ch) DTS-ES OOOOOdts L, C, R, SL, SR, LFE Multi CH-PCM AAC (5.1ch) AAC EX OOO - O AAC L, C, R, SL, SR, LFE Dolby Surr. EX Dolby Digital 5.1 OOO * O2 DIGITAL EX L, C, R, SL, SR, S, LFE Dolby D (5.1ch) Dolby Digital 5.1 OOO * O2 DIGITAL L, C, R, SL, SR, LFE Dolby D (2ch) Pro Logic IIx OOOOO2 DIGITAL L, R Dolby D (2ch Surr) Pro Logic IIx OOOOO2 DIGITAL , 2 SURROUND L, R, S Multi Ch-PCM Multi Ch-PCM + PLIIx OOOOOPCM L, C, R, SL, SR, LFE PCM (Audio) Pro Logic IIx OOOOOPCM L, R Analog Pro Logic IIx OOOOOANALOG - DTS-ES DTS 5.1 OOO - O dts, ES L, C, R, SL, SR, S, LFE DTS 96/24 DTS 96/24 OOO - O dts 96/24 L, C, R, SL, SR, LFE DTS (5.1ch) DTS 5.1 OOO - O dts L, C, R, SL, SR, LFE PCM (Audio) Neo:6 OOOOOPCM L, R Analog Neo:6 OOOOOANALOG - Dolby D (2ch) Neo:6 OOOOO2 DIGITAL L, R Dolby D (2ch Surr) Neo:6 OOOOO2 DIGITAL , 2 SURROUND L, R, S
Multi Ch-PCM + Dolby EX
Output Channel Front information display
SLSRSBL
L/R C
OOOOOPCM L, C, R, SL, SR, LFE
SBR
Signal format indicators Channel status
SubW
Surround Mode
CS II Cinema CS II Music
II
CS
STEREO Dolby Surr. EX Stereo O ---O2 DIGITAL EX L, C, R, SL, SR, S, LFE
Virtual Dolby Surr. EX Virtual O ----2 DIGITAL EX L, C, R, SL, SR, S, LFE
Multi Ch. Stereo
Input Signal Decoding
PCM (Audio) CS Analog CS
Mono
Dolby D (2ch) CS Dolby D (2ch Surr) CS
Dolby D (5.1ch) Stereo O ---O2 DIGITAL L, C, R, SL, SR, LFE Dolby D (2ch) Stereo O ---O*2 DIGITAL L, R Dolby D (2ch Surr) Stereo O ---O*2DIGITAL , 2 SURROUND L, R, S DTS-ES Stereo O ---O dts, ES L, C, R, SL, SR, S, LFE DTS 96/24 Stereo O ---O dts 96/24 L, C, R, SL, SR, LFE DTS (5.1ch) Stereo O ---O dts L, C, R, SL, SR, LFE Multi Ch-PCM Stereo O ---O PCM L, C, R, SL, SR, LFE PCM (Audio) Stereo O ---O PCM L, R PCM 96kHz Stereo O ---O PCM L, R HDCD PCM (Stereo) O ---O PCM HDCD L, R Analog Stereo O ---O ANALOG -
Dolby D (5.1ch) Virtual Dolby D (2ch) Virtual O ----2 DIGITAL L, R Dolby D (2ch Surr) Virtual O ----2 DIGITAL , 2 SURROUND L, R, S DTS-ES Virtual O ----dts, ES L, C, R, SL, SR, S, LFE DTS (5.1ch) Virtual O ----dts L, C, R, SL, SR, LFE Multi Ch-PCM Virtual O ----PCM L, C, R, SL, SR, LFE PCM (Audio) Virtual O ----PCM L, R Analog Virtual O ----ANALOG ­Dolby Surr. EX Dolby Digital EX OOOOO2 DIGITAL EX L, C, R, SL, SR, S, LFE Dolby D (5.1ch) Dolby Digital 5.1 OOO - O2 DIGITAL L, C, R, SL, SR, LFE Dolby D (2ch) Multi Channel Stereo OOOOO*2 DIGITAL L, R Dolby D (2ch Surr) Multi Channel Stereo OOOOO*2 DIGITAL , 2 SURROUND DTS-ES DTS-ES OOOOOdts, ES L, C, R, SL, SR, S, LFE DTS 96/24 DTS 96/24 OOOOOdts 96/24 L, C, R, SL, SR, LFE DTS (5.1ch) DTS 5.1 OOO - O dts L, C, R, SL, SR, LFE Multi Ch-PCM Multi Ch-PCM OOO - O PCM L, C, R, SL, SR, LFE Multi Ch-PCM 96kHz Multi Ch-PCM 96kHz OOO - O PCM L, C, R, SL, SR, LFE PCM (Audio) Multi Channel Stereo OOOOO*PCM L, R Analog Multi Channel Stereo OOOOO*ANALOG -
II II II II
Output Channel Front information display
SLSRSBL
L/R C
OOOOOPCM L, R OOOOOANALOG - OOOOO2 DIGITAL L, R OOOOO2 DIGITAL , 2 SURROUND L, R, S
O ----2 DIGITAL L, C, R, SL, SR, LFE
Signal format indicators Channel status
SubW
SBR
* : Depending on the particular setup, there may be differences compared to the information contained in
these tables.
O* : When L/R (FRONT Speaker) = SMALL.
Notes:
• Dolby Digital (2 ch: Lt/Rt): signal with Dolby Surround fl ag Speakers are full set.
• No sound outputs from the surround speaker, center speaker and subwoofer if the DVD disc has no surround data.
Abbreviations L/R : Front speakers C : Center speaker SL/SR : Surround speakers SBL/SBR : Surround Back speakers SubW : Sub woofer speaker
36
AUTO
When this mode is selected, the unit determines whether the digital input signal is Dolby Digital, Dolby Digital Surround EX, DTS, DTS-ES, DTS 96/24 or PCM-audio. Surround EX & DTS-ES will operate for multichannel source that has a Dolby Digital Surround EX or DTS­ES auto trigger fl ag in the digital signal. When a Dolby Digital or DTS signal is input, the number of channels for which the corresponding signal is encoded will be played. Inputting a Dolby Digital two channel signal with Dolby surround status automatically subjects that signal to Pro Logic II x movie processing before play. PCM 96 kHz source material can be played in this mode.
Notes:
• When you use this mode with certain DVD and CD players, performing operations such as “Skip” or “Stop” may momentarily interrupt the output.
• When the signal is not decoded, the mode is changed to AUTO mode automatically. Refer to page 35 to confi rm the available decoding mode.
SOURCE DIRECT
In the Source Direct mode, the tone control circuit and bass management confi guration are bypassed for full-range frequency response and the purist audio reproduction.
Notes:
• Speaker size is set to Front L/R = LARGE, Center = LARGE, Surround L/R = LARGE and Subwoofer = YES automatically. Tone controls, equalizer and additional processing are deactivated.
• When you use this mode with certain DVD and CD players, performing operations such as skip or stop may momentarily interrupt the output.
PURE DIRECT
The Pure Direct mode further reduces sources of noise in addition to effect of the Source Direct mode, by blocking output from the video jacks (VIDEO, S-VIDEO, COMPONENT VIDEO and HDMI) and turning the FL display off.
EX/ES
This mode provides 6.1 channel surround for DOLBY DIGITAL EX, DTS-ES encoded source material such as DVD. This mode cannot be used when an analog input has been selected.
Dolby Digital EX
In a movie theater, fi lm soundtracks that have been encoded with Dolby Digital surround EX technology are able to reproduce an extra channel which has been added during the mixing of the program. This channel, called Surround Back, places sounds behind the listener in addition to the currently available front left, front center, front right, surround right, surround left and subwoofer channels. This additional channel provides the opportunity for more detailed imaging behind the listener and brings more depth, spacious ambience and sound localization than ever before. Dolby Digital EX is not available in the system without surround back speaker(s).
DTS-ES (Discrete 6.1, Matrix 6.1)
DTS-ES adds the surround back channel audio to the DTS 5.1-channel format to improve the acoustic positioning and makes acoustic image movement more natural with the 6.1-channel reproduction. This unit incorporates a DTS-ES decoder, which can handle DTS-ES Discrete-encoded and DTS-ES Matrix-encoded program sources from DVD, etc.. DTS-ES Discrete 6.1 features digital discrete recording of all channels including the surround back channel(s) and higher quality of audio reproduction. DTS-ES is not available in the system without a surround back speaker.
2 MODE
(Dolby Digital, Pro Logic IIx MOVIE, Pro Logic II x MUSIC, Pro Logic IIx GAME, Pro Logic)
This mode is used with source materials encoded in Dolby Digital and Dolby Surround.
DOLBY DIGITAL
This mode is enabled when playing source materials encoded in Dolby Digital. Playing multichannel encoded 6.1 or 7.1-channel Dolby Digital sources provides five main audio channels (left, center, right, surround left and surround right) and Low Frequency Effect channel. Dolby Digital EX decoding is not available in this mode.
Dolby Pro Logic IIx brings the excitement of surround sound to any stereo mix, while making existing Dolby Surround mixes sound more like discrete 5.1 channels Surround sound. Dolby Pro Logic IIx has 3 modes. Please see below.
Pro Logic
This mode provides 6.1 or 7.1 channel surround sound from Dolby Surround encoded stereo movie sound tracks.
Pro Logic IIx MUSIC
This mode provides 6.1 or 7.1 channel surround sound from conventional stereo sources, analog or digital, such as CD, Tape, FM, TV, Stereo VCR, etc.
Pro Logic IIx GAME
Game mode restores the impact low-frequency surround effects by routing them to the system’s subwoofer.
Pro Logic
This mode emulated original Dolby Pro Logic decoding (3/1 surround) suit for Dolby Surround encoded stereo movie soundtracks.
Notes:
II
x MOVIE
• Pro Logic IIx mode will decode as Pro Logic II mode when the SURROUND BACK SPEAKER is set NONE in SPEAKER SETUP menu. (See SPEAKER SETUP, page 27)
• Pro Logic IIx mode is available for a 2ch input signal which is encoded in Dolby Digital or PCM format.
• PCM-audio signals can be subjected to Pro Logic processing when the sampling frequency is 32 kHz,
44.1 kHz or 48 kHz.
dts MODE
(dts, Neo:6 Cinema, Neo:6 Music)
This mode is for DTS encoded source materials such as LASER DISC, CD, and DVD. Neo:6 is for some 2 channel sources.
dts : This mode is enabled when playing source materials encoded in dts multichannel. Playing multichannel encoded 5.1-channel dts sources provides five main audio channels (left, center, right, surround left and surround right) and Low Frequency Effect channel. dts-ES decoding is not available in this mode. The DTS mode cannot be used when an analog input has been selected.
Neo:6 Cinema, Neo:6 Music
This mode decodes 2-channel signals into 6­channel signals using high-accuracy digital matrix technology. The DTS NEO:6 decoder has near-discrete properties in the frequency characteristics of the channels as well as in channel separation. According to the signals to be played back, DTS NEO:6 uses either the NEO:6 CINEMA mode optimized for movie playback or the NEO:6 MUSIC mode optimized for music playback.
Notes:
Neo:6 mode is available to 2ch input signals which are encoded in Dolby Digital or PCM Analog format.
• PCM-audio signals can be subjected to Neo:6 processing when the sampling frequency is 32 kHz,
44.1 kHz or 48 kHz.
ENGLISH
37
ENGLISH
CIRCLE SURROUND II
II
-CINEMA, CSII-MUSIC, CSII-MONO)
(CS
Circle Surround is designed to enable multichannel surround sound playback of non-encoded and multichannel encoded material. Backward compatibility provides listeners with up to
6.1 channels of surround performance from entire collection of music and fi lm, including broadcast, videotape and stereo recorded music. Depending on source material, you can select CS Cinema mode, CSII-Music mode or CSII-Mono mode.
CSII Cinema mode
This mode is suited for playing back Circle Surround­encoded and non-encoded film and television soundtracks. Cinema Mode enables 6.1-channel surround playback of 2-channel sources such as Video Cassettes, TV broadcasts, streaming media and DVDs.
CSII Music mode
This mode is suited for playing back Circle Surround­encoded and non-encoded music. Music Mode decodes, music DVDs, radio and TV music broadcasts and CDs into enveloping 6.1-channel surround.
CSII-Mono mode
This mode plays back monaural recordings from any source, including CDs, DVDs and TV and radio broadcasts in compelling 6.1-channel surround.
Notes:
• CS II mode is available for 2ch input signals which are encoded in Dolby Digital or PCM format.
• PCM-audio signals can be subjected to CS II processing when the sampling frequency is 32 kHz,
44.1 kHz or 48 kHz.
STEREO
This mode bypasses all surround processing. In stereo program sources, the left and right channels play normally when PCM-audio or analog stereo is input. With Dolby Digital and DTS sources, the 5.1 multichannels are converted to two channel stereo. 96 kHz PCM source material can be played back in stereo mode.
II
-
VIRTUAL
This mode creates a virtualized surround sound experience from a two-speaker (front L and R) playback system playing any multichannel audio source (such as found on DVDs and digital broadcasts), including Dolby Digital, Dolby Pro Logic or DTS.
MULTI CH. ST
This mode is used to create a wider, deeper and more natural soundstage from two channel source material. This is done by feeding the left channel signal to both left front and left surround speaker and the right channel signal to both right front and right surround speaker. Additionally, the center channel reproduces a mix of the right and left channel.
CAUTION
NOTE for DTS signal
* Connected DVD player, laserdisc player or CD
player needs to support DTS digital output. You may not be able to play some DTS source signals from certain CD players and LD players even if you connect the player to this unit digitally. This is because the digital signal has been processed (such as the output level, sampling frequency or frequency response), and this unit cannot recognize the signal as DTS data.
* You can not listen to DTS-encoded software in a
multiroom.
* Depending on the player used, DTS play may
produce a short noise. This is not a malfunction.
* While signals from a DTS laserdisc or CD are
playing in another surround mode, you cannot switch to digital input or from digital input to analog input from the INPUT SETUP in the MAIN MENU or by pressing the A/D button.
* The outputs for VCR 1 OUT, DSS/VCR 2 OUT,
TAPE OUT, and CD-R OUT output analog audio signals only. Do not record from CDs or LDs that support DTS using these outputs. If you do, the DTS-encoded signal will be recorded as noise.
NOTE for Dolby Digital Surround EX signal
* When playing Dolby Digital Surround EX-encoded
software in 6.1 channels, it is required to set the EX/ES mode.
* Note that some of Dolby Digital Surround
EX-encoded software does not contain the identifi cation signal. In this case, set the EX/ES mode manually.
NOTE for 96 kHz/192 kHz PCM audio
* The AUTO, Pure Direct, and Stereo modes can be
used when playing PCM signals with a sampling frequency of 96/192 kHz (such as from DVD­Video/Audio discs).
* Certain DVD player models inhibit digital output.
For details, refer to the player’s operation manual.
* Some DVD discs feature copy protection. When
using such disc, 96 kHz PCM signal is not output from the DVD player. For details, refer to the player’s operation manual.
NOTE for HDCD signal
* HDCD is effective only through digital input. * You may not be able to play some HDCD source
signals from certain CD players if you connect the player to this unit digitally. This is because the digital signal has been processed (such as the output level, sampling frequency or frequency response) and this unit cannot recognize the signal as HDCD data.
38
OTHER FUNCTION
SS
456
DISPLAY MODE
R SR5002
SIMPLE
PURE
SURROUND
SETUP
DIRECT
MODE
AUTO
HT-EQ
MENU
MEMORY
DISPLAY
ENTER
CLEAR
T-MODE
EXIT
BAND
You can select the display mode for the front display of the unit. To select this mode, press the DISPLAY on the remote controller. When this button is pressed, the display mode is switched in the following sequence.
Surround Mode Auto-display Off Display Off
Input Function Surround Mode....
In Auto display off mode, the display is off. But, if you make a change to the unit such as input or surround mode, the display will show that change, then go back to off after about 3 seconds. When changing the volume, it is not displayed. In Display off mode, the display is off completely.
Note:
Only the DISP indicator will be illuminated on the front display in display off condition
LEARN
SOURCE
l/
P.DIRECT
SLEEP
DISPLAYDISPLAY
AUTO
123
EX/ES
VIRTUAL
CS
456
STEREO
M-CH ST
789
SEND
OFFONSET
SURROUND
LIP SYNC/
INPUT
dts
T.MODE
P.SCAN
NIGHT
RECORDING AN ANALOG SOURCE
In normal operation, the audio or video source selected for listening through this unit is sent to the record outputs. This means that any program you are watching or listening to may be recorded simply by placing machines connected to the outputs for TAPE OUT, CD/CDR OUT, VCR OUT in the record mode.
To record the input source signal you are currently watching or listening to
1.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
SIMPLE
PURE
SURROUND
MULTI
SPEAKER
MULTI
STANDBY
SETUP MIC
PHONES
POWER ON/STANDBY
1. Select the input source to record by turning the INPUT SOURCE knob on the front panel or simply press the input selector buttons on the remote controller.
The input source is now selected and you may
watch or listen to it as desired.
The currently selected input source signal is
2.
output to the TAPE OUT, CD/CDR OUT, VCR OUT outputs for recording.
Start recording to the recording component as
3.
desired.
SETUP
DIRECT
MODE
1.
AUTO
HT-EQ
MENU
PRESET
-
DISC+
CH-SEL
BASS
TVTV
TUNERTUNER
TAPE
REMOTE CONTROLLER
ANGLE
V-OFF
DVDDVD VCRVCR
CDCD
AUX1
-
SUB TITLE
ATT.
CDRCDR
AUX2
TUNING
++
AUDIO
TREBLE
DSSDSS
MDMD
AMP
Recording the video from one source and the audio from another
You can add the sound from one source to the video of another source to make your own video recordings. Below is an example of recording the sound from a compact disc player connected to CD IN and the video from a video camera connected to DSS to video cassette recorder connected to the VCR OUT jack.
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
BASS
1.
2.
TV
TUNER
TAPE
REMOTE CONTROLLER
TREBLE
DVD
DSS
VCRVCR
MD
CDR
CDCD
AMP
AUX2
AUX1
1. Switch the video output source to VCR by simply pressing the input selector buttons on the remote controller.
Switch the audio input source to CD by simply
2.
pressing the input selector buttons on the remote controller.
Now “CD” has been selected as the audio input
3.
source and “VCR” as the video input source.
Notes:
• If you change the input source during recording, you will record the signals from the newly selected input source.
• You cannot record the surround effects.
• Digital input signals are only output to the digital outputs. There is no conversion from digital to analog.
When connecting CD players and other digital
components, do not connect only the digital terminals, but the analog ones as well.
SELECTING ANALOG AUDIO INPUT OR DIGITAL AUDIO INPUT
DVD
VCR
TV
TUNER
TAPE
REMOTE CONTROLLER
M-CH ST
789
7.1CH IN
CL
CAT
CH/
MULTI/
If you have already assigned the digital inputs, you can temporarily select the audio input mode for each input source as following procedures. Press the AMP button and press the A/D (0) button. When this button is pressed, the input mode is switched in the following sequence. HDMI Auto HDMI → Digital Analog HDMI
Auto....
In
HDMI
Auto mode, the types of signals being input to the digital and analog input jacks for the selected input source are detected automatically. If no digital signal is being input, the analog input jacks are selected automatically. In Digital and
HDMI assigned digital input terminal. In analog mode, the analog input jacks are selected. This selecting is temporary, so the result will not be stored in memory. If you need to change the input mode completely, use INPUT SETUP in OSD menu system. (see page 27)
D
MD
CDR
CD
AMPAMP
AUX2
AUX1
P.SC A N
STEREO
NIGHT
HT-EQ
A/DA/D
MEMO
+10+10
0
VOLUME
MUTE
SPKR A/B
CAT
M-SPKR
mode, input is fixed to an
ENGLISH
39
ENGLISH
T.DISP
F.DIRECT
PTY
REC
LISTENING THROUGH HEADPHONES
This jack may be used to listen to the unit’s output through a pair of headphones. Be certain that the headphones have a standard 1/4” stereo phono plug. Note that the speakers will automatically be turned off when the headphone jack is in use.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
MULTI
SPEAKER
MULTI
STANDBY
SETUP MIC
PHONES
POWER ON/STANDBY
Notes:
• When using headphones, the surround mode will change to BYPASS and Dolby Headphone by MENU and Cursor button.
• The surround mode returns to the previous setting as soon as the headphone plug is removed from the jack.
• The tone control function can not work through the headphones output.
PURE
SURROUND
DIRECT
MODE
AUTO
HT-EQ
DOLBY HEADPHONE MODE
This feature simulates the waveforms of the actual sounds heard from the speakers. When headphones are used, the MENU button automatically switches to the Dolby headphone mode. The OSD that appears when the MENU button is pressed is shown below.
HEAD PHONE
SIMPLE
SETUP
MENU
DOLDBY HP (Headphone) MODE can be selected with the left and right cursor buttons. BYPASS ON BYPASS
DOLBY HP MODE : ON SURROUND : OFF
L LEVEL : 0 dB R LEVEL : 0 dB
ATTENUATION TO ANALOG INPUT SIGNAL
TUNING
PRESET
-
-
++
AUDIO
ANGLE
DISC+
SUB TITLESUB TITLE
CH-SEL
V-OFF
ATT.ATT.
BASS
TREBLE
DVD VCR
TV
TUNER
If the selected analog audio input signal is greater than the capable level of internal processing, the “PEAK” indicator will light up on the front display. If this happens, you should press the ATT button on the remote controller. “ATT ” indicator will be illuminated when this function is activated. The signal-input level is reduced by about half. Attenuation will not work with the output signal of TAPE-OUT, CD/CDR-OUT and VCR-OUT. This function is memorized for each individual input source.
DSS
MD
CDR
CD
7.1 CH INPUT
This unit is equipped for future expansion through the use of Multi channel Super Audio CD multichannel player or DVD-Audio player. When this is selected, the input signals connected to the L(front left), R (front right), CENTER, SL (surround left), SR (surround right) and SBL (surround back left) and SBR (surround back right) channels of the 7.1 CH. In jacks are output directly to the front (left and right), center, surround (left and right) and surround back speaker systems as well as the pre-out jacks without passing through the surround circuitry. In addition, the signal input to the SW (subwoofer) jack is output to the PRE OUT SW (subwoofer) jack. When 7.1 CH. INPUT is selected, the last video input used remains routed to the Monitor Outputs. This permits simultaneous viewing with video sources.
BYPASS: Bypasses the Dolby headphone mode
and delivers ordinary 2-channel stereo.
ON: Dolby headphone mode active.
When the PURE DIRECT and SOURCE DIRECT mode is selected, Dolby surround processing is bypassed and “✽✽✽” is displayed as the mode indication.
The surround mode can be selected when mode is ON.
L/R LEVEL can be set in the ±10 dB range.
Notes:
• The surround mode returns to the previous setting as soon as the plug is removed from the jack.
• The Dolby Headphone function will not work when 32 or 96 kHz PCM digital signals are input.
SPEAKER A/B
P.SCAN
STEREO
NIGHT
M-CH ST
789
CL
CAT
CH/
MULTI/
INFO
This unit has speaker system - A and speaker system- B for front L/R channels. You can select these systems by pressing
SPEAKERS A/B button on the front panel or SPK­AB on the remote controller.
7.1CH IN
SPKR A/B
HT-EQ
A/D
MEMO
+10
0
VOLUME
MUTE
CAT
M-SPKR
MENU
40
1.2.
U
N
P.SCAN
STEREO
NIGHT
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
2.
PURE
SURROUND
MULTI
SPEAKER
MULTI
STANDBY
SETUP MIC
PHONES
POWER ON/STANDBY
4.
DOWN
CLEAR
MEMORY
BAND
1. Select a desired Video source to decide the
2.
3.
Adjust the speaker output levels so that you can
The subwoofer can be adjusted between –15
These adjustments result will be stored to 7.1
4.
To cancel the 7.1 CH. INPUT setting, press the 7.1 CH INPUT button on the front panel or press 7.1 CH IN on the remote controller.
Notes:
MUTE
T-MODE
DIGITAL
S-VIDEO
routed video signal to the Monitor Outputs.
Press the 7.1 CH INPUT button on the front
panel or press 7.1 CH IN on the remote controller to switch the 7.1 channel input.
If it is necessary to adjust the output level of
each channel, press the CH.SEL button on the remote controller.
hear the same sound level from each speaker at the listening position. For the front left, front right, center, surround left, surround right and surround back speakers, the output levels can be adjusted between –10 to +10 dB.
and +10 dB.
CH. INPUT memory.
Adjust the main volume with the MAIN VOLUME
knob or the VOLUME buttons on the remote controller.
• 7.1 CH. Input mode bypasses the internal surround processing, so SURROUND mode cannot be selected.
• In addition, there is no signal at the record outputs when the 7.1 CH. Input is in use.
DIRECT
MODE
AUTO
VOLUME
UP
ATT
AUX 1 INPUT
RLVIDEO
AUDIO
4.
HT-EQ
1.
M-CH ST
789
7.1CH IN7.1CH IN
CL
00
CAT
CH/
SPKR A/B
CAT
MULTI/
INFO
ENTER
T.TONE /SET UP
T.DISP
REC
PRESET
-
ANGLE
DISC+
CH-SEL
V-OFF
BASS
DVDDVD VCRVCR
TVTV
CD
TUNER
AUX1
TAPE
REMOTE CONTROLLER
M-SPKR
SUB TITLE
HT-EQ
A/D
MEMO
+10
VOLUMEVOLUME
MUTE
MENU
EXIT
F.DIRECT
PTY
TUNING
-
++
AUDIO
ATT.
TREBLE
DSSDSS
MD
CDR
AMP
AUX2
AUX2 INPUT
If you don’t need to connect 7.1 Ch. input terminals with multi channel decoder, L(front left) and R (front right) inputs terminals are available as AUX2 input. In this case, You can connect additional audio source to AUX2 as other audio input terminals.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
SIMP
PURE
SURROUND
POWER ON/STANDBY
MULTI
SPEAKER
MULTI
STANDBY
SETUP MIC
PHONES
SET
DIRECT
MODE
AUTO
HT-EQ
ME
HT-EQ (HOME THEATER EQUALIZER)
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
SIMPLE
PURE
SURROUND
STANDBY
POWER ON/STANDBY
MULTI
SPEAKER
MULTI
SETUP MIC
PHONES
SETUP
DIRECT
MODE
AUTO
HT-EQ
MENU
MEMORY
DISPLAY
ENTER
CLEAR
T-MODE
EXIT
BAND
At cinemas, the front left, front right and center speakers are located behind the screen. So, screen damping is taken into account when mastering movie software, with an emphasis on high frequencies. When playing back such software at home, the signal takes on different characteristics from those at the cinema. This unit includes HT-EQ to rectify the sound difference between that experienced at a cinema and in a home theater, allowing you to enjoy the same sound you would experience at the cinema at home. The HT-EQ feature is available except in the following modes.
• 7.1 CH INPUT
• PURE-DIRECT
• SOURCE DIRECT
• When VIRTUAL is set for the surround mode Press the HT-EQ button on the unit.
1.
“EQ” indicator on the front panel will illuminate,
indicating the HOME THEATER EQUALIZER has been activated.
To cancel this function, press the HT-EQ button
2.
again.
“EQ” indicator on the front panel will be
turned off, indicating the HOME THEATER EQUALIZER has been deactivated.
VOLUME
DOWN
MUTE
AUX 1 INPUT
DIGITAL
S-VIDEO
TV AUTO ON/OFF FUNCTION
This function allows the component connected to the TV-VIDEO in jack to control the power (ON/OFF) to the unit.
AUTO POWER ON
1. Be sure the TV auto mode is ENABLED. (Refer page 28 : System Setup)
Connect your TV TUNER (etc) to the TV-
2.
VIDEO in terminal. Be sure to connect the VIDEO input.
Turn OFF the power to the TV TUNER and the
3.
unit.
Turn ON the TV TUNER and tune in a receivable
4.
station.
When the station is received, this unit turns ON
5.
and TV is selected automatically.
AUTO POWER OFF
1. In the above situation, turn the TV TUNER OFF
LVIDEO
or select a channel that does not contain any broadcast.
The power to the unit switches to STANDBY
2.
after approx. 5 minutes.
Notes:
• AUTO POWER OFF is canceled if this unit is set to a source other than TV.
The function reactivates when TV is selected again.
• Some TV broadcasts may cause the TV AUTO FUNCTION to turn ON.
• The S-Video terminal does not support “TV AUTO ON/OFF” function.
VIDEO ON/OFF
When no video signal is connected to the unit or a DVD, etc., is connected directly to your TV, the unnecessary video circuit can be turned off by selecting the “VIDEO OFF” setting. To select video off, press the AMP button and press the V-OFF button.
DVD
VCR
CDR
CD
AUX2
AUX1
REMOTE CONTROLLER
T.DISP
PTY
-
ANGLE
SUB TITLE
V-OFF
ATT.
BASS
DVD VCR
DSS
MD
AMPAMP
F.DIRECT
TUNING
++
AUDIO
TREBLE
DSS
TV
5002
SIMPLE
PURE
SURROUND
SETUP
DIRECT
MODE
AUTO
HT-EQ
MENU
MEMORY
DISPLAY
ENTER
CLEAR
T-MODE
EXIT
BAND
TUNER
TAPE
REC
PRESET
-
DISC+
CH-SEL
TV
LIP.SYNC (SR5002 only)
Depending on the image device (TV, monitor, projector, etc.) connected to the SR5002, a time lag can occur between image signal processing and audio signal processing. Though minor, this time lag can interfere with movie and music enjoyment. The LIP.SYNC feature delays the audio signal with respect to the image signal output from the SR5002 to correct the time lag between the sound and image. It can be operated with the “LIP.SYNC” and 1 and 2 cursor buttons of the remote controller. Set the remote controller to the AMP mode before operating the LIP.SYNC feature. The initial setting is OFF (0 ms).The time lag can be adjusted in 10 ms steps up to 200 ms. Watch the picture on the image device (i.e., TV, monitor, projector, etc.) as you adjust the time lag.
Note:
The LIP.SYNC feature turns OFF (0 ms) in the SOURCE DIRECT mode. When the SOURCE DIRECT mode is deactivated, the set value of the LIP. SYNC feature is automatically restored.
ENGLISH
41
ENGLISH
M
M
BASIC OPERATION
(TUNER)
LISTENING TO THE TUNER
Frequency scan step for AM is selectable. Default setup is 10 kHz step, if your country’s standard is 9 kHz step, press BAND button on the remote controller more than 6 seconds. Scan step will change.
Note:
Preset memory for the tuner will clear by changing this setup.
AUTO TUNING
SLEEP
1.2.
1.
DOWN
SIMPLE
PURE
D
SETUP
DIRECT
HT-EQ
MENU BAND
(Using the unit)
To select tuner and desired band (FM or AM),
1.
press the BAND button on the front panel.
Press the
2.
panel for more than 1 second to start the auto tuning function.
Automatic searching begins then stops when a
3.
station is tuned in.
(Using the remote controller)
To select tuner and desired band (FM or
1.
AM), press the BAND button on the remote controller.
Press the 5 or 6 for more than 1 second on
2.
the remote controller.
Automatic searching begins then stops when a
3.
station is tuned in.
If tuning does not stop at the desired station, use to the “Manual tuning” operation.
MEMORY
DISPLAY
ENTER
CLEAR
T-MODE
EXIT
3 or 4 cursor buttons
DIGITAL
2.
AUTO
123
CS
456
M-CH ST
789
REC
PRESET+TUNINGTUNING
-
DISC+
CH-SEL
on the front
MANUAL TUNING
P.DIRECT
DISPLAY
dts
EX/ES
VIRTUAL
STEREO
NIGHT
T.DISP
PTY
PRESET+TUNINGTUNING
--
ANGLE
SUB TITLE
V-OFF
ATT.
SURROUND
T.MODE
F.DIRECT
PURE
D
DIRECT
HT-EQ
SIMPLE
SETUP
DISPLAY
ENTER
EXIT
MENU BAND
SLEEP
1.2.
1.
DOWN
MEMORY
CLEAR
T-MODE
DIGITAL
2.
AUTO
123
CS
456
M-CH ST
789
REC
-
DISC+
CH-SEL
(Using the unit)
To select tuner and desired band (FM or AM),
1.
press the BAND button on the front panel.
Press the
2.
P.DIRECT
SURROUND
DISPLAY
LIP SYNC/ INPUT
dts
BAND
T.MODE
EX/ES
VIRTUAL
P.SCAN
STEREO
NIGHT
panel to select the desired station.
(Using the remote controller )
To select tuner and desired band (FM or
1.
3 or 4 cursor buttons
on the front
AM), press the BAND button on the remote
T.DISP
F.DIRECT
PTY
--
++
AUDIO
ANGLE
SUB TITLE
V-OFF
ATT.
controller.
Press the 5 or 6 on the remote controller to
2.
tune in the desired station.
DIRECT FREQUENCY CALL
P.DIRECT
OFFONSET
SOURCE
l/
P.DIRECT
SLEEP
AUTO
11 22 33
CS
3.
1.
44 55 66
M-CH ST
77 88 99
CL
CAT
CH/
To select tuner and desired band (FM or
SURROUND
DISPLAY
LIP SYNC/ INPUT
dts
EX/ES
VIRTUAL
STEREO
NIGHT
7.1CH IN
A/D
00
+10
MUTE
SPKR A/B
CAT
MULTI/
M-SPKR
1.
T.MODE
P.SCAN
HT-EQ
MEMO
VOLUME
2.
SLEEP
AUTO
123
CS
456
M-CH ST
789
/SET UP
REC
-
AM), press the BAND button on the remote controller.
Press the F.DIRECT on the remote controller,
2.
display will show “FREQ - - - -”.
Input your desired station’s frequency with the
3.
numeric buttons on the remote controller. The desired station will automatically be tuned.
4.
SURROUND
DISPLAY
dts
T.MODE
EX/ES
VIRTUAL
STEREO
NIGHT
7.1CH IN
A/D
T.DISP
PTY
F.DIRECTF.DIRECT
TUNING
PRESET
-
(FM) TUNING MODE (AUTO STEREO OR MONO)
LIP SYNC/ INPUT
BAND
P.SCAN
++
AUDIO
DISPLAY
CLEAR
MEMORY
ENTER
T-MODE
EXIT
BAND
When in the auto stereo mode, AUTO indicator will be illuminated on the display. The “ST” indicator is illuminated when a stereo broadcast is tuned in. At open frequencies, the noise is muted and the “TUNED” and “ST” indicators are not illuminated. If the signal is weak, it may be diffi cult to tune into the station in stereo. In such a case, press the T-MODE button on the front panel or remote controller. “AUTO ” indicator is not illuminated, if FM stereo broadcasts are received in monaural and the “ST” indicator is not illuminated. To return to auto stereo mode, press the T-MODE button or press T-MODE button on the remote controller
again. AUTO indicator is illuminated on the
display.
VOLUME
DOWN
DIGITAL
UP
ATT
MUTE
AUX 1 INPUT
RLVIDEO
S-VIDEO
AUDIO
PRESET MEMORY
LIP SYNC/ INPUT
With this unit you can preset up to 50 FM/AM stations
BAND
in any order. For each station, you can memorize the frequency
P.SCAN
and reception mode if desired.
HT-EQ
EXIT
AUTO PRESET MEMORY
This function automatically scans the FM and AM
++
band and enters all stations with proper signal strength into the memory.
2. 2. 5.4. 1. 3.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
SIMPLE
PURE
SURROUND
POWER ON/STANDBY
MULTI
SPEAKER
MULTI
STANDBY
SETUP MIC
PHONES
SETUP
DIRECT
MODE
AUTO
HT-EQ
MENU
MEMORY
DISPLAY
ENTER
EXIT
BAND
SOURCE
l/
SLEEP
AUTO
123
CS
456
M-CH ST
789
CL
CAT
CH/
CLEAR
T-MODE
While pressing the MEMO button, press the 2
2.
cursor button.
AUTO PRESET” will appear on the display,
and scanning starts from the lowest frequency.
Each time the tuner fi nds a station, scanning
3.
will pause and the station will be played for fi ve seconds.
During this time, the following operations are
possible. The band can be changed by the BAND button.
If no button is pressed during this period, the
4.
DISPLAY
STEREO
7.1CH IN
SPKR A/B
OFFONSET
P.DIRECT
SURROUND
LIP SYNC/
INPUT
dts
T.MODET.MODE
EX/ES
VIRTUAL
P.SCAN
NIGHT
HT-EQ
A/D
MEMO
0
+10
VOLUME
MUTE
current station is memorized in location Preset
02.
If you wish to skip the current station, press the
3 cursor button during this period, this station is skipped and auto presetting continues.
Operation stops automatically when all 50
5.
preset memory positions are fi lled or when auto scanning attains the highest end of all bands. If you desire to stop the auto preset memory at anytime, press the CLEAR button.
Note:
It is possible that existing preset memory positions will be overwritten.
MANUAL PRESET MEMORY
P.DIRECT
SLEEP
AUTO
11 22 33
CS
44 55 66
M-CH ST
77 88 99
CL
CAT
CH/
INFO
CEIVER SR5002
3. 2. 4.
SIMPLE
PURETSURROUND
SETUP
DIRECT
MODE
AUTO
HT-EQ
MENU
3.
MEMORY
DISPLAY
ENTER
EXIT
BAND
2.
(Using the unit)
Tune into the radio station you desire (Refer to
1.
the “MANUAL TUNING” or “AUTO TUNING
VOLUME
DOWN
DIGITAL
UP
ATT
MUTE
AUX 1 INPUT
RLVIDEO
S-VIDEO
AUDIO
section).
Press the MEMORY button on the front panel.
2.
– –“ (preset number) starts blinking on the display.
Select the preset number by pressing the 1
3.
or 2
cursor
buttons, while this is still blinking
SURROUND
DISPLAY
LIP SYNC/ INPUT
dts
T.MODE
EX/ES
VIRTUAL
P.SCAN
STEREO
NIGHT
HT-EQ
7.1CH IN
A/D
MEMOMEMO
+10
00
VOLUME
MUTE
SPKR A/B
CAT
MULTI/
M-SPKR
MENU
(approx. 5 seconds)
Press the MEMORY button again to enter. The
To select FM, press the BAND button on the
1.
front panel.
4.
display stops blinking.
The station is now stored in the specifi ed preset
memory location.
42
(Using the remote controller)
T.DISP
F.DIRECT
PTY
REC
Tune into the radio station you desire (Refer to
1.
the “MANUAL TUNING” or “AUTO TUNING section).
Press the MEMO button on the remote
2.
controller. “– –“ (preset number) starts blinking on the display.
Enter the desired preset number by pressing
3.
the numeric buttons.
Note:
When entering a single digit number (2 for example), either input “02” or just input “2” and wait for a few seconds.
RECALLING A PRESET STATION
1.
1.
SIMPLE
PURE
SURROUND
SETUP
DIRECT
MODE
AUTO
HT-EQ
MENU
MEMORY
DISPLAY
ENTER
CLEAR
T-MODE
EXIT
BAND
1.
(Using the unit)
Select the desired preset station by pressing
1.
the 1 or 2
(Using the remote controller)
Press the S or T buttons to select the
1.
desired preset station, or input your desired preset channel with the numeric buttons on the remote controller.
cursor
buttons on the front panel
SLEEP
AUTO
11 22 33
CS
44 55 66
M-CH ST
77 88 99
CL
CAT CAT
CH/CH/
PRESET
-
DISC+
PRESET SCAN
T.MODE
EX/ES
VIRTUAL
CS
456
M-CH ST
789
3.
CLCL
CAT CAT
CH/CH/
REC
-
DISC+
CH-SEL
P.SCANP.SCAN
STEREO
NIGHT
7.1CH IN
A/D
0
+10
MUTE
SPKR A/B
T.DISP
PTY
TUNING
PRESET
-
ANGLE
SUB TITLE
V-OFF
ATT.
1.
HT-EQ
MEMO
3.
VOLUME
F.DIRECT
++
3.
AUDIO
(Using the remote controller)
Press the P.SCAN on the remote controller.
1.
PRESET SCAN” appears on the display and
then the preset station with the lowest preset number is recalled fi rst.
Preset stations are recalled in sequence (No.1
2.
No.2 etc.) for 5 seconds each.
No stored preset number will be skipped.
You can fast forward the preset stations by
3.
pressing the T continuously.
When the desired preset station is received,
cancel the preset scan operation by pressing the CLEAR button or P.SCAN on the remote controller.
P.DIRECT
SURROUND
DISPLAY
LIP SYNC/
INPUT
dts
T.MODE
EX/ES
VIRTUAL
P.SCAN
STEREO
NIGHT
HT-EQ
7.1CH IN
A/D
MEMO
00
+10
VOLUME
MUTE
SPKR A/B
TUNING
-
AUDIO
ANGLE
SUB TITLE
CLEARING STORED PRESET STATIONS
You can remove preset stations from the memory using the following procedure.
2. 3.
VOLUME
++
DISPLAY
ENTER
EXIT
Recall the preset number to be cleared with
1.
DOWN
CLEAR
MEMORY
BAND
MUTE
T-MODE
DIGITAL
2.
AUX 1 INPUT
3.
VIDEO
S-VIDEO
AUTO
123
EX/ES
VIRTUAL
CS
456
STEREO
M-CH ST
789
7.1CH IN
CLCL
0
CAT
CH/
SPKR A/B
CAT
MULTI/
M-SPKR
INFO
dts
T.MODE
P.SCAN
NIGHT
A/D
+10
VOLUME
MUTE
the method described in “Recalling” a preset station.
Press the MEMORY button on the front panel
2.
or press the MEMO button on the remote controller.
The stored preset number blinks in the display
3.
for 5 seconds. While blinking, press the CLEAR button on the front panel or the remote controller
xx CLEAR” appears on the display to indicate
4.
.
that the specified preset number has been cleared.
Note:
To clear all stored preset stations, press and hold the CLEAR and the ENTER buttons for two seconds.
SORTING PRESET STATIONS
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
SIMPLE
PURE
SURROUND
POWER ON/STANDBY
MULTI
SPEAKER
MULTI
STANDBY
SETUP MIC
PHONES
SETUP
DIRECT
MODE
AUTO
HT-EQ
MENU
MEMORY
DISPLAY
ENTER
EXIT
BAND
If you have stations memorized, and there is a gap in the sequential order: I.e. the stations are stored as follows
1) 87.1 MHz
2) 93.1 MHz
3) 94.7 MHz
10) 105.9 MHz (notice there is no stations programmed for pre sets for 4-9), you can have pre set 10 become pre set 5: To sort the numbers, press the 4 cursor button while pressing the MEMORY button. “PRESET SORT” will appear on the display and
LIP SYNC/ INPUT
sorting will be done.
NAME INPUT OF THE PRESET STATION.
HT-EQ
This function allows the name of each preset channel
MEMOMEMO
to be entered using alphanumeric characters. Before name inputting, you need to store preset stations with the preset memory operation.
MENU
SIMPLE SETUP
ENTER
MENU
CH/CH/
INFO
T.TONE /SET UP
REC
-
DISC+
CH-SEL
5. 2. 5. 6.
MEMORY
DISPLAY
EXIT
BAND
789
7.1CH IN
A/D
CL
+10
0
CAT CAT
MUTE
SPKR A/B
CAT
MULTI/
M-SPKR
ENTERENTER
T.DISP
PTY
PRESET
--
+
ANGLE
SUB TITLE
V-OFF
ATT.
BASS
DVD VCR
TV
4.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
PURE
SURROUND
MULTI
SPEAKER
MULTI
STANDBY
SETUP MIC
PHONES
POWER ON/STANDBY
2. 5. 6.
DIRECT
MODE
AUTO
HT-EQ
5.
4.
Recall the preset number to be inputted name
1.
VOLUME
DOWN
CLEAR
T-MODE
DIGITAL
UP
ATT
MUTE
AUX 1 INPUT
RLVIDEO
S-VIDEO
AUDIO
with the method described in “Recalling” a preset station.
Press the MEMORY button on the front panel
2.
or press the MEMO button on the remote controller for more than 3 seconds.
The left most column of the station name
3.
ENGLISH
indicator fl ashes, indicating the character entry ready status.
When you press the 3 or 4 cursor buttons
4.
on the front panel or the 5 / 6 buttons on the remote controller, alphabetic and numeric characters will be displayed in the following order:
A B C ... Z 1 2 3 ..... 0 +
/ (Blank) A
UP DOWN
After selecting the fi rst character to be entered,
5.
press the MEMORY or ENTER buttons, press the MEMO button on the remote controller.
The entry in this column is fi xed and the next
column starts to fl ash. Fill the next column the same way.
To move back and forth between the characters,
press the 1 / 2 cursor buttons or press S or T buttons on the remote controller.
Note:
VOLUME
DOWN
CLEAR
T-MODE
DIGITAL
UP
ATT
MUTE
AUX 1 INPUT
RLVIDEO
S-VIDEO
AUDIO
Unused columns should be fi lled by entering blanks.
To save the name, press the MEMORY button
6.
on the front panel or remote controller for more than 2 seconds.
Ten keypad Press, press again, press again, etc.
1
HT-EQ
MEMOMEMO
VOLUME
MENU
2
3
4
5
6
7
EXIT
F.DIRECT
TUNINGTUNING
++
AUDIO
TREBLE
DSS
8
9
0
A
B → C → 1 → A
D → E → F → 2 → D
G
H → I → 3 → G
J → K → L → 4 → J
M → N → O → 5 → M
P → Q → R → 6 → P
S → T → U → 7 → S
V → W → X → 8 → V
Y → Z → space → 9 → Y
– → + → / → 0
43
ENGLISH
LISTENING TO XM SATELLITE RADIO (SR5002 ONLY)
SELECTING AN INPUT SOURCE
Before you can listen to XM Satellite Radio, you must fi rst select the input source on the SR5002.
OFFONSET
SOURCE
l/
P.DIRECT
DISPLAY
dts
EX/ES
VIRTUAL
STEREO
NIGHT
7.1CH IN
A/D
00
+10
ANGLE
SUB TITLE
V-OFF
ATT.
BASS
DVD
VCR
CDR
CD
AUX2
AUX1
REMOTE CONTROLLER
RC5001SR
SURROUND
LIP SYNC/ INPUT
BAND
T.MODE
P.SCAN
HT-EQ
MEMO
AUDIO
TREBLE
DSS
MD
AMP
POWER ON/STANDBY
1.
MULTI
STANDBY
INPUT SELECTOR
SETUP MIC
AV SURROUND RECEIVER SR5002
MULTI
SPEAKER
PHONES
SLEEP
AUTO
112233
CS
445566
M-CH ST
778899
PURE
SURROUND
DIRECT
MODE
AUTO
CL
HT-EQ
DISC+
CH-SEL
TV
TUNERTUNER
TAPE
2.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
DOWN
SIMPLE
PURE
SURROUND
POWER ON/STANDBY
MULTI SPEAKER
MULTI
STANDBY
SETUP MIC
PHONES
SETUP
DIRECT
MODE
AUTO
HT-EQ
MENU
MEMORY
DISPLAY
CLEAR
ENTER
T-MODE
EXIT
BAND
DIGITAL
CHECKING THE XM SIGNAL STRENGTH AND RADIO ID
ENTER
T.TONE /SET UP
REC
PRESET
-
DISC+
CH-SEL
2.
1. Press the T.DISP button 3 times to displayed
EXIT
F.DIRECT
PTY
T.DISPT.DISP
TUNING
-
++
1.
AUDIO
ANGLE
SUB TITLE
V-OFF
ATT.
BASS
TREBLE
Signal Status.
SIGNAL:
• The display changes as shown below according to
1.
the receiving condition.
Select channel 0 (XM000) with the 3 or 4
3.
cursor buttons of the SR5002 or the Q or R buttons of the remote controller.
MENU
INFO
ENTER
T.TONE /SET UP
EXIT
T.DISP
F.DIRECT
PTY
REC
TUNING
PRESET
-
-
++
AUDIO
ANGLE
SUB TITLE
DISC+
DISPLAY
CH-SEL
V-OFF
ATT.
BASS
TV
TUNER
TAPE
REMOTE CONTROLLER
DVD VCR
CD
AUX1
TREBLE
DSS
MD
CDR
AMP
AUX2
EXIT
OWER ON/STANDBY
3.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
SIMPLE
PURE
SURROUND
MULTI
SPEAKER
MULTI
STANDBY
SETUP MIC
PHONES
SETUP
DIRECT
MODE
AUTO
ENTER
HT-EQ
MENU
• The Radio ID is displayed.
XMOOORADIO ID
SWITCHING XM INFORMATION IN THE FRONT PANEL DISPLAY
You can display XM information (such as artist name/ song title, category or signal status) for the channel currently selected in the front panel display.
ENTER
T.TONE
3.
/SET UP
REC
PRESET
-
DISC+
CH-SEL
EXIT
F.DIRECT
PTY
T.DISPT.DISP
TUNING
-
++
1.
AUDIO
ANGLE
SUB TITLE
V-OFF
ATT.
BASS
TREBLE
1. Press the T.DISP button to displayed
INFORMATION.
Channel number/name
Artist name/Song title
SIGNAL: ■■■■■■ SIGNAL: STRONG (Signal strength is good)
Notes:
VOLUME
UP
ATT
MUTE
AUX 1 INPUT
RLVIDEO
S-VIDEO
AUDIO
SIGNAL: MARGINAL (Signal strength is Marginal)
SIGNAL: ■■ SIGNAL: WEAK
SIGNAL: ■■■■
• If “ANTENNA” appears in the front panel display,
the XM Mini-Tuner and Home Dock may not be connected to the XM terminal on the rear panel of this unit properly.
• The ATT function is also effective when XM is selected.
(Signal strength is poor)
Channel category
Signal Status
When the Channel number/name is displayed:
XMO40:DeepTrc
(Using the SR5002)
1. Turn the INPUT SELECTOR knob to select “TUNER”.
Press the BAND button to select XM band.
2.
(Using the remote controller)
To select tuner, Press the TUNER button twice
1.
within two seconds on the remote controller.
Press the BAND button to select XM band.
2.
44
XM NO SIGNAL SIGNAL: NON (Loss of the signal)
Adjust the antenna location until signal strength
2.
is good.
40:DeepTracks
(If text is more than 13 characters long, the text is scrolled.)
Note:
The front Panel display can indicate up to 13 alphanumeric characters at once. If the information contains more then 13 characters, the information scrolls from right to left.
When the channel Artist name/Song title is displayed:
NAME/TITLE
Pink Floid /
Floid / Money
The “NAME/TITLE” is displayed for 2 seconds, followed by the artist’s name and song title. (If artist’s name or song title is more than 13 characters long, the text is scrolled.)
Note:
The front Panel display can indicate up to 13 alphanumeric characters at once. If the information contains more then 13 characters, the information scrolls from right to left.
When the channel category is displayed:
CAT:Rock
Note:
To change the display content from XM information to SR5002 functions, do so with the DISPLAY button.
This XM information can also be displayed on a TV monitor connected to the SR5002.
CAT
CH/
INFOINFO
T.TONE /SET UP
REC
DISC+
CH-SEL
TV
TUNER
TAPE
1. Press the AMP button on the remote controller.
MUTE
SPKR A/B
CAT
MULTI/
M-SPKR
ENTER
T.DISP
PTY
ANGLE
SUB TITLE
V-OFF
ATT.
BASS
DVD VCR
CDR
CD
AUX2
AUX1
REMOTE CONTROLLER
RC5001SR
VOLUME
MENU
2.
EXIT
F.DIRECT
AUDIO
TREBLE
DSS
MD
AMPAMP
1.
When you press the INFO button, the following
2.
information will be displayed.
VIDEO :DVD AUDIO :XM
SURR-MODE:AUTO MULTIROOM:ON MULTISPKR:OFF
MAIN VOLUME
--------------------
MAIN RETURN EXIT
3. When this display appears, press the INFO button again. XM information like the following will appear.
XM INFORMATION
XM :040 CHAN :DeepTracks NAME :Pink Floid TITLE :Money CAT :Rock
SIGNAL:MARGINAL
MAIN RETURN EXIT
4. Press the INFO button again. The information display will go out.
Note:
If the information contains a character that cannot be recognized by that unit, the character will be displayed with “ ”(space).
SEARCH MODE
You can search for the channel you want to listen to using one of three search modes. You can also enter the number directly to select the desired channel.
ALL CHANNEL SEARCH MODE
3. 2.1.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
SIMPLE
PURE
SURROUND
POWER ON/STANDBY
MULTI
SPEAKER
MULTI
STANDBY
SETUP MIC
PHONES
DIRECT
MODE
AUTO
HT-EQ
SOURCE
l/
SLEEP
DISPLAY
AUTO
112233
EX/ES
CS
445566
STEREO
M-CH ST
778899
REC
T.DISP
PRESET
-
ANGLE
DISC+
CH-SEL
V-OFF
BASS
TV
TUNERTUNER
AUX1
TAPE
REMOTE CONTROLLER
DVD
CD
+
RC5001SR
SETUP
MENU
OFFONSET
P.DIRECT
dts
VIRTUAL
NIGHT
PTY
TUNINGTUNING
--
SUB TITLE
ATT.
VCR
CDR
AUX2
MEMORY
DISPLAY
ENTER
SURROUND
LIP SYNC/ INPUT
BAND
T.MODE
P.SCAN
F.DIRECT
++
AUDIO
TREBLE
DSS
MD
AMP
CLEAR
T-MODE
EXIT
BAND
2.
3.
1.
(Using the SR5002)
Turn the INPUT SELECTOR knob to select
1.
“TUNER”.
Press the BAND button to select XM band.
2.
Press the 3 or 4 cursor button on the front
3.
panel to select the desired station.
(Using the remote controller)
To select tuner, Press the TUNER button twice
1.
within two seconds on the remote controller.
Press the BAND button to select XM band.
2.
Press and hold the 5 or 6 button.
3.
VOLUME
DOWN
DIGITAL
UP
ATT
MUTE
AUX 1 INPUT
RLVIDEO
S-VIDEO
AUDIO
PRESET SEARCH MODE
3. 2.1.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
SIMPLE
PURE
SURROUND
POWER ON/STANDBY
MULTI
SPEAKER
MULTI
STANDBY
SETUP MIC
PHONES
SETUP
DIRECT
MODE
AUTO
HT-EQ
MENU
LEARN
SOURCESOURCE
l/l/
SLEEP
DISPLAY
AUTO
123
EX/ES
CS
456
T.DISP
REC
PRESETPRESET
--
++
ANGLE
DISC+
CH-SEL
V-OFF
BASS
DVD VCR
TV
CD
TUNERTUNER
AUX1
TAPE
REMOTE CONTROLLER
RC5001SR
P.DIRECT
VIRTUAL
SUB TITLE
MEMORY
DISPLAY
ENTER
SEND
OFFONSET
SURROUND
LIP SYNC/ INPUT
dts
BAND
T.MODE
F.DIRECT
PTY
TUNING
-
AUDIO
ATT.
TREBLE
DSS
CDR
AMP
AUX2
CLEAR
T-MODE
EXIT
BAND
2.
+
3.
MD
1.
(Using the SR5002)
Turn the INPUT SELECTOR knob to select
1.
“TUNER”.
Press the BAND button to select XM band.
2.
Press the 1 or 2 cursor button on the front
3.
panel to select the desired preset station.
(Using the remote controller)
To select tuner, Press the TUNER button twice
1.
within two seconds on the remote controller.
Press the BAND button to select XM band.
2.
S or T button to tune in the desired
3.
preset station.
Or enter the preset station number with the
numeric buttons.
VOLUME
DOWN
DIGITAL
UP
ATT
MUTE
AUX 1 INPUT
RLVIDEO
S-VIDEO
AUDIO
ENGLISH
45
ENGLISH
CATEGORY SEARCH MODE
You can select the desired channel from the category allocated to each channel. Category being aired can be only selected.
1. 5. 3. 6.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
SIMPLE
PURE
SURROUND
POWER ON/STANDBY
MULTI
SPEAKER
MULTI
STANDBY
SETUP MIC
PHONES
SETUP
DIRECT
MODE
AUTO
HT-EQ
MENU
MEMORY
DISPLAY
ENTER
CLEAR
T-MODE
EXIT
BAND
4. 2.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
SIMPLE
PURE
SURROUND
POWER ON/STANDBY
MULTI
SPEAKER
MULTI
STANDBY
SETUP MIC
PHONES
AUTO
M-CH ST
CH/CH/
INFO
T.TONE /SET UP
DISC+
CH-SEL
TUNERTUNER
DIRECT
MODE
AUTO
HT-EQ
dts
123
EX/ES
VIRTUAL
CS
456
STEREO
NIGHT
789
7.1CH IN
A/D
CL
0
+10
CAT CAT
MUTE
SPKR A/B
CAT
MULTI/
M-SPKR
ENTER
T.DISP
PTY
REC
PRESET
-
-
ANGLE
SUB TITLE
V-OFF
ATT.
BASS
DVD VCR
TV
CDR
CD
AUX2
AUX1
TAPE
SETUP
MENU
LIP SYNC/ INPUT
BAND
T.MODE
P.SCANP.SCAN
HT-EQ
MEMO
VOLUME
MEMORY
DISPLAY
ENTER
CLEAR
T-MODE
EXIT
BAND
2.
5.
MENU
4.
EXIT
F.DIRECT
TUNING
++
AUDIO
6.
TREBLE
DSS
MD
AMP
1. 3.
(Using the SR5002)
Turn the INPUT SELECTOR knob to select
1.
“TUNER”.
Press the BAND button to select XM band.
2.
Press the ENTER button on the front panel.
3.
Press the 1 or 2 button on the front panel to
VOLUME
DOWN
MUTE
AUX 1 INPUT
DIGITAL
S-VIDEO
4.
select the desired Category.
UP
ATT
RLVIDEO
AUDIO
After selecting the Category, Press the 3 or 4
5.
cursor button to select the desired station of the category.
You can return to the normal mode by press the
6.
ENTER button during Category Search Mode.
(Using the remote controller)
VOLUME
To select tuner, Press the TUNER button twice
1.
within two seconds on the remote controller.
DOWN
DIGITAL
UP
ATT
MUTE
AUX 1 INPUT
RLVIDEO
S-VIDEO
AUDIO
Press the BAND button to select XM band.
2.
Press the TUNER button twice within two
3.
seconds on the remote controller.
Press the MULTI/CAT button.
4.
Press the CAT 3 or CAT 4 button.
5.
After selecting the category, Press the Q or
6.
R button to select the desired station of the category.
7. You can return to the normal mode by press the MULTI/CAT button during Category Search Mode.
Note:
Category search automatically ends 5 minutes after the last operation.
CHANNEL DIRECT CALL
You can select the desired channel by directly tapping the numeric keypads on the remote controller.
OFFONSET
SOURCE
l/
P.DIRECTP.DIRECT
DISPLAY
EX/ES
STEREO
7.1CH IN
00
SPKR A/B
ENTER
T.DISP
PRESET
ANGLE
V-OFF
BASS
DVD
CD
AUX1
REMOTE CONTROLLER
RC5001SR
VIRTUAL
NIGHT
+10
-
SUB TITLE
AUX2
SURROUND
LIP SYNC/ INPUT
dts
BAND
T.MODE
P.SCA N
HT-EQ
A/D
MEMO
VOLUME
MUTE
EXIT
F.DIRECT
PTY
TUNING
AUDIO
ATT.
TREBLE
VCR
DSS
MD
CDR
AMP
2.
5.
++
4.
1. 3.
SLEEP
AUTO
11 22 33
CS
44 55 66
M-CH ST
77 88 99
CL
CAT
CH/
T.TONE /SET UP
REC
-
DISC+
CH-SEL
TV
TUNERTUNER
TAPE
The desired channel will automatically be
6.
tuned.
Note:
If there is no input on the keypad for 5sec., the input is cancelled to return to the original display
Notes:
“LOADING” is displayed while receiving the channel or information.
“UPDATING” is displayed while updating encryption code.
When the selected channel is not available, “XM - -
-” is dispIayed.
“OFF AIR” is displayed while air is suspended (e.g. midnight).
1. To select tuner, Press the TUNER button twice within two seconds on the remote controller.
Press the BAND button to select XM band.
2.
Press the TUNER button twice within two
3.
seconds on the remote controller.
Press the F.DIRECT button.
4.
XM - - -” will appear on the display.
Input the three digit number for your desired
5.
Channel with the numeric keypad on the remote controller.
46
PRESET MEMORY
D
D
.
You can store the desired channel in the Preset Memory. In addition to AM and FM, it is possible to preset 50 XM channels.
OFFONSET
SOURCE
l/
3. 2.4.
SIMPLE
PURE
ROUND
SETUP
DIRECT
ODE
UTO
HT-EQ
DISPLAY
ENTER
EXIT
MENU
MEMORY
CLEAR
BAND
T-MODE
SLEEP
AUTO
11 22 33
CS
44 55 66
M-CH ST
77 88 99
CL
CAT
CH/
(Using the SR5002)
Tune into the desired channel.
1.
Press the MEMORY button on the front panel.
2.
- -” (preset number) starts blinking on the
dispIay.
--XM040
3. Select the preset number by pressing the 1 or 2 cursor buttons, While this is still blinking (approx. 5 seconds)
01XM040
4. Press the MEMORY button again to enter.
The display stops blinking. The station is now stored in the specifi ed preset
memory location.
(Using the remote controller)
Tune into the desired channel.
1.
Press the MEMO button on the remote
2.
controller. “- -” (preset number) starts blinking on the display.
Enter the desired preset number by pressing
3.
the numeric buttons.
Note:
When entering a single digit number (2 for example), either input “02” or just input “2” and wait for a few seconds.
SURROUND
P.DIRECT
DISPLAY
LIP SYNC/ INPUT
dts
T.MODE
EX/ES
VIRTUAL
P.SCAN
STEREO
NIGHT
7.1CH IN
A/D
HT-EQHT-EQ
MEMOMEMO
+10
00
VOLUME
MUTE
SPKR A/B
CAT
MULTI/
M-SPKR
3.
2.
CHECKING THE XM PRESET CHANNEL
The preset channel can be checked on the on screen display.
LIP SYNC/
INPUT
dts
AUTO
123
CS
456
M-CH ST
789
CL
CAT CAT
CH/CH/
INFOINFO
T.TONE /SET UP
TV
TUNERTUNER
TAPE
(Using the remote controller)
To select tuner, Press the TUNER button twice
1.
within two seconds on the remote controller.
Press the BAND button to select XM band.
2.
Press the TUNER button twice within two
3.
seconds on the remote controller.
Press the INFO button. to view a list of tuner
4.
preset channeI on the on screen display.
If there are 10 or more preset channel, Press
5.
the INFO button. again.
XM PRESET LIST
NO. 1 XM010 XXXXXXXXXX NO. 2 XM011 XXXXXXXXXX NO. 3 XM015 XXXXXXXXXX NO. 4 XM022 XXXXXXXXXX NO. 5 XM125 XXXXXXXXXX NO. 6 XM001 Preview NO. 7 XM001 Preview NO. 8 XM001 Preview NO. 9 XM001 Preview
MAIN RETURN EXIT
Note:
The preset channel indication disappears in about 5 sec.
EX/ES
VIRTUAL
STEREO
NIGHT
7.1CH IN
A/D
0
+10
MUTE
SPKR A/B
CAT
MULTI/
M-SPKR
ENTER
BASS
DVD VCR
CDR
CD
AUX2
AUX1
REMOTE CONTROLLER
RC5001SR
BAND
T.MODE
P.SCAN
HT-EQ
MEMO
VOLUME
2.
MENU
4. 5.
EXIT
TREBLE
DSS
MD
AMP
1. 3
PRESET SCAN
T.MODE
EX/ES
VIRTUAL
CS
456
M-CH ST
789
CL
CAT CAT
CH/CH/
-
DISC+
CH-SEL
TV
TUNERTUNER
TAPE
1. Press the TUNER button twice within two seconds on the remote controller.
Press the P.SCAN.
2.
Preset stations are recalled in sequence (No.1
3.
No.2 etc.) for about 5-10 seconds each. The time changes by the received condition. No stored preset number will be skipped.
Pressing the T button during prescanning
4.
speeds up scanning.
Also, pressing the S button returns to the
previous preset station.
When the desired preset station is received,
5.
cancel the preset scan operation by press the
P. SCAN button.
STEREO
7.1CH IN
0
SPKR A/B
CAT
MULTI/
PRESET
ANGLE
V-OFF
BASS
DVD VCR
CD
AUX1
REMOTE CONTROLLER
RC5001SR
SUB TITLE
P.SCAN
NIGHT
HT-EQ
A/D
MEMO
+10
VOLUME
MUTE
M-SPKR
TUNING
-
AUDIO
ATT.
TREBLE
CDR
AUX2
2. 5.
++
4.
DSS
MD
AMP
1.
CLEARING STORED PRESET STATIONS
You can remove preset stations from the memory using the following procedure.
AUTO
123
CS
456
VOLUME
M-CH ST
789
CLCL
CAT
CH/
AUX 1 INPUT
VIDEO
S-VIDEO
INFO
PLE TUP
DISPLAY
ENTER
EXIT
ENU BAND
3.2.
DOWN
CLEAR
MEMORY
MUTE
T-MODE
DIGITAL
1. Recall the preset number to be cleared with the method described in “PRESET SERCH MODE”.
Press the MEMORY button on the front panel
2.
or Press the MEMO button on the remote controller.
The stored preset number blinks in the display
3.
for 5 seconds. WhiIe blinking, Press the CLEAR button on the front panel or CL button on the remote controller.
xx CLEAR” appears on the dispIay to indicate
4.
that the specified preset number has been cleared.
Notes:
• To clear all stored preset stations, press and hold
the CLEAR (CL) and the ENTER buttons for two seconds.
• There are 50 preset channels prepared at the factory default. The 50 channels are all set to “CHANNEL 001”. Each channel can be stored in the preset memory. You can search for only the preset channels.
LIP SYNC/
INPUT
dts
T.MODE
EX/ES
VIRTUAL
P.SCA N
STEREO
NIGHT
HT-EQHT-EQ
7.1CH IN
A/D
MEMOMEMO
+10
0
VOLUME
MUTE
SPKR A/B
CAT
MULTI/
M-SPKR
2.
3.
MENU
ENGLISH
47
ENGLISH
MULTI ROOM SYSTEM
The Multi Room system is a function which allows you to listen to the same or a different source in a room other than the room in which the SR5002 is located. The operations possible with the multi room function are explained briefl y below. For details, refer to the instruction manual supplied with the multi room remote controller and SR5002.
When the outputs of the MULTI OUT terminals are wired and connected to amplifi ers installed in other rooms or M (MULTI) SPEAKER B terminals are wired and connected to L&R speakers in other room, different sources can be played in rooms other than the main room in which the SR5002 and the playback devices are installed.
SR5002 has some feature to MULTI ROOM SYSTEM as source selector, sleep timer, Multi Room Speaker output and remote control.
(SR5002 only)
MULTI ROOM PLAYBACK USING THE MULTI ROOM OUT TERMINALS
The SR5002 is equipped with audio pre-out terminals for which the volume is adjustable as the MULTI output terminals. A separately sold stereo power amplifier can be connected to enjoy multi room playback.
2. 3.1. 4.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
MULTI
STANDBY
SETUP MIC
POWER ON/STANDBY
1. 4.
MULTI
SPEAKER
PHONES
2.
SIMPLE
PURE
SURROUND
SETUP
DIRECT
MODE
AUTO
HT-EQ
MENU
CL
00
CAT
CH/
SPKR A/B
CAT
MULTI/
INFO
ENTER
T.TONE /SET UP
T.DISP
REC
PRESET
-
ANGLE
DISC+
CH-SEL
V-OFF
BASS
DVDDVD VCRVCR
TVTV
CD
TUNER
AUX1
TAPE
REMOTE CONTROLLER
+10
M-SPKR
SUB TITLE
AUX2
MEMORY
DISPLAY
ENTER
MUTE
PTY
-
ATT.
CDR
CLEAR
T-MODE
EXIT
BAND
MEMO
VOLUMEVOLUME
MENU
EXIT
F.DIRECT
TUNING
++
AUDIO
TREBLE
DSSDSS
MD
AMP
DOWN
MUTE
DIGITAL
S-VIDEO
3.
1. 4.
VOLUME
ATT
AUX 1 INPUT
AUDIO
MULTI ROOM PLAYBACK USING THE MULTI SPEAKER TERMINALS
The SR5002 allows you to connect another set of speakers and place them in a different room or separated area for listening to music.
2. 3.1. 4.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
DOWN
SIMPLE
PURE
SURROUND
UP
RLVIDEO
POWER ON/STANDBY
SETUP MIC
PHONES
MULTI
SPEAKER
MULTI
STANDBY
1. 4.
2.
SETUP
DIRECT
MODE
AUTO
HT-EQ
MENU
CL
CAT
CH/
SPKR A/B
MULTI/
INFO
T.TONE /SET UP
T.DISP
REC
PRESET
-
ANGLE
DISC+
CH-SEL
BASS
TVTV
TUNER
TAPE
REMOTE CONTROLLER
00
CAT
ENTER
V-OFF
DVDDVD VCRVCR
CD
AUX1
MEMORY
DISPLAY
M-SPKR
SUB TITLE
CLEAR
T-MODE
EXIT
BAND
DIGITAL
MEMO
+10
VOLUMEVOLUME
MUTE
3.
MENU
EXIT
F.DIRECT
PTY
TUNING
-
++
AUDIO
ATT.
TREBLE
DSSDSS
MD
CDR
AMP
AUX2
1. 4.
ENTER
Press the MULTI SPEAKER (M-SPKR) button.
1.
The unit enters multi room speaker mode and the display indicates “SELCT SOURCE” and fl ashes the “MULTI” indicators for approx. 10 seconds.
Select the input source using the INPUT
2.
SELECTOR knob or function button on the remote controller.
VOLUME
UP
ATT
MUTE
AUX 1 INPUT
RLVIDEO
S-VIDEO
AUDIO
Then, the display indicates “MSPKR VOLUME
MSPKR VOL.–xx” for approx. 5 seconds.
During this time, you can set the volume level in
3.
the multi room as desired.
This will only set the volume in the multi room.
To cancel this function, press the MULTI button
4.
on the unit or remote controller (after pressing the AMP button on the remote controller).
“MULTI” indicator on the front panel will be
turned off.
Notes for MULTI ROOM SPEAKER
• MULTI ROOM SPEAKER On/ Off is available in main room only.
• MULTI ROOM SPEAKER output terminals can be used when the SURROUND BACK SPEAKER is set NONE in SPEAKER SETUP menu. (See SPEAKER SETUP, page 27)
• “The Surr. Back Speakers are in use” is displayed by pressing the MULTI SPEAKER (M-SPKR) button when the SURROUND BACK SPEAKER is set except NONE in SPEAKER SETUP menu. (See SPEAKER SETUP, page 27)
48
Press the MULTI button on the unit or remote
1.
controller (after pressing the AMP button on the remote controller). The unit enters MULTI ROOM mode, and the display indicates “SELECT SOURCE.” The “MULTI” indicator will fl ash for about 10 seconds.
Select the input source using the INPUT
2.
SELECTOR knob or function button on the remote controller.
Then, the display indicates “MULTI VOLUME”
MULTI VOL. xx” for approx. 5 seconds.
During this time, you can set the volume level in
3.
the multi room as desired.
This will only set the volume in the second room.
To cancel this function, press the MULTI button
4.
on the unit or remote controller (after pressing the AMP button on the remote controller).
“MULTI” indicator on the front panel will be
turned off.
SURROUND SPEAKER B SYSTEM
(SR4002 only)
The Surround Speaker B system is a function which allows you to listen to the same source in a room other than the room in which the SR4002 is located. The operations possible with the Surround speaker function are explained briefl y below.
ANOTHER ROOM PLAYBACK USING THE S (SURROUND) SPEAKER B TERMINALS
The SR4002 allows you to connect another set of speakers and place them in a another room or separated area for listening to music. The SURROUND SPEAKER B system can not be operated with the supplied remote controller.
2.1.
AV SURROUND RECEIVER SR4002
INPUT SELECTOR
SIMPLE
PURE
SURROUND
STANDBY
SETUP MIC
POWER ON/STANDBY
Press the S (Surround) SPEAKER B button.
1.
AUTO
HT-EQ
PHONES
MENU
SETUP
DIRECT
MODE
S.SPEAKER B
7.1 CH INPUT
MEMORY
DISPLAY
ENTER
CLEAR
T-MODE
EXIT
BAND
The unit enters surround speaker B mode and the “SPKR B” will appear on the display.
The volume of S. SPEAKER B is interlocked
2.
with the main volume.
Notes for SURROUND SPEAKER B
• SURROUND SPEAKER B On/ Off is available in main room only.
• SURROUND SPEAKER B
output terminals can be used when the SURROUND BACK SPEAKER is set NONE in SPEAKER SETUP menu. (See SPEAKER SETUP, page 27)
• “The Surr. Back Speakers are in use” is displayed
by pressing the S. SPEAKER B button SURROUND BACK SPEAKER is set except NONE in SPEAKER SETUP menu. (See SPEAKER SETUP, page 27)
• Surround Speaker B function is unavailable, while the unit is 7.1 CH input mode.
DOWN
MUTE
DIGITAL
VOLUME
ATT
AUX 1 INPUT
S-VIDEO
AUDIO
when the
UP
RLVIDEO
ENGLISH
49
ENGLISH
TROUBLESHOOTING
In case of trouble, check the following before calling for service:
1. Are the connections made properly ?
2. Are you operating the unit properly following the user’s guide ?
3. Are the power amplifi ers and speaker working properly ?
If the unit does not operate properly, check items shown in the following table. If your trouble cannot be recovered with the remedy actions listed in the following table, malfunction of the internal circuitry is suspected; immediately unplug the power cable and contact your dealer, nearest Marantz authorized dealer or the Marantz Service Center in your country.
SYMPTOM CAUSE REMEDY
This unit cannot be turned up. The power plug is not connected. Connect the power plug to the outlet.
No sound and picture are output even when power is on.
No speaker output. The headphones are connected to the
Incorrect Audio or Video for selected source.
Incorrect Audio from a channel.
No Audio output from the center channel speaker.
No Audio output from the surround speakers.
No Audio output from the surround back speakers.
Mute is on. Cancel mute using the remote controller.
The input cable is not connected correctly.
The master volume control is turned all the way down.
The SOURCE position is wrong. Select correct position.
headphone jack.
Input cable connected incorrectly. Connect the cable correctly by referring to the
Speaker cable connected incorrectly. Connect the cable correctly by referring to the
The center speaker cable connection is incomplete.
STEREO has been selected for Surround mode.
Center = NONE has been selected in SETUP mode.
The surround speaker cable connection is incomplete.
STEREO has been selected for Surround mode.
Surround = NONE has been selected in SETUP mode.
The surround back speaker cable connection is incomplete.
Surround mode is not EX/ES mode. Set surround mode EX/ES.
Surround back = NONE has been selected in SPEAKERS SIZE SETUP
See the connection diagram and connect the cables correctly.
Adjust the master volume.
Disconnect the headphones. (Speakers will not output sound when headphones are connected.)
connection diagram.
connection diagram.
Connect the cable correctly.
When STEREO is selected for Surround mode, no sound will be output from the center speaker. Set another Surround mode.
Make the correct setting.
Connect the cable correctly.
When STEREO has been selected for Surround mode, no sound will be output from the surround speaker. Set another Surround mode.
Make the correct setting.
Connect the cable correctly.
Make the correct setting.
SYMPTOM CAUSE REMEDY
Can not select EX/ES mode. Surround center= NONE has been
Can not select Pro Logic II x mode.
Can not select Neo:6 mode. Input signal is incompatible. Use 2 channel Dolby Digital input signal, PCM input
Can not select CSII mode. Input signal is incompatible. Use 2 channel Dolby Digital input signal, PCM input
No output to Sub Woofer Out. Sub-woofer = NONE has been selected in
Noise is produced during DTS­encoded CD or laser disc play.
A specifi c channel does not produce output.
FM or AM reception fails. Antenna connection is incomplete. Correctly connect the indoor FM and AM antennas to
Noise is heard during AM reception.
Noise is heard during FM reception.
Cannot get programmed station when the PRESET button is pressed.
Control with the remote controller fails.
MRAC is not working. Headphones are connected. Disconnect the headphones.
MRAC is going to CANCEL mode automatically.
selected in SPEAKERS SIZE SETUP
Input signal is incompatible. Use 5.1channel source.
Input signal is incompatible. Use 2 channel Dolby Digital input signal, PCM input
SETUP mode.
Analog has been selected for input. Be sure to perform digital connection, select digital
Nothing recorded on source. Check the encoded channel on the source side.
Reception is affected by other electrical fi elds.
The radio waves from the broadcasting station are weak.
Preset data has been erased. Disconnecting power plug for long periods of time will
Batteries are consumed. Replace all the batteries with new ones.
Remote controller’s function-key setting is wrong.
The distance between this unit and the remote commander is too far.
Something is blocking this unit and the remote commander.
Are the speakers set to OFF? Set SPK A or SPK B to ON.
Make the correct setting.
signal or analog input signal.
signal or analog input signal.
signal or analog input signal.
Select Sub-woofer = YES.
input, then play.
FM and AM antenna outlets.
Try changing location where the AM indoor antenna is set up.
Install an FM outdoor antenna.
erase preset data. If that happens, input the preset data again.
Select different position from which equipment will be controlled.
Move closer to this unit.
Remove offending object.
50
HDMI
SYMPTOM CAUSE REMEDY
The display does not appear over an HDMI connection.
The SR4002/5002 OSD menu does not appear over an HDMI connection.
Time is needed for the display of an HDMI connection to appear.
Audio is not played back over an HDMI connection.
DVD-Audio is not played back over an HDMI connection.
Super Audio CD is not played back over an HDMI connection.
The connected monitor or projector does not support HDCP. • Connect to equipment that supports HDCP.
The HDMI input of on the TV is not on. Set HDMI input so that it turns on, as explained in the TV’s instruction manual.
The HDMI output on the source component (DVD, Set Top Box, etc.) is not on.
The HDMI mode is not correctly set on the unit. Set HDMI input on the FUNC INPUT SETUP menu as explained on page 33.
The HDMI output video resolution of the source component (DVD, Set Top Box, etc.) does not match the TV specifi cations.
The device is connected with a non-standard HDMI cable. A 5 m or shorter cable is recommended to ensure stable operation and prevent image quality
Power to the unit is off. (When the unit is on standby, HDMI connections cannot be turned on.)
The connection between HDMI components was not authenticated.
The unit SETUP menu does not support HDMI output. Use the COMPONENT VIDEO, S-VIDEO or VIDEO output.
The connection is being authenticated between the HDMI devices.
The HDMI audio output of the source component (DVD, Set Top Box, etc.) is not on.
The signal format of the source component (DVD, Set Top Box, etc.) is not supported by the unit.
The unit is set to the HDMI audio “THROUGH” mode. In the “THROUGH” mode, sound is not produced from the unit. Set it to “ENABLE”. (see page 30)
The DVD player does not support CPPM, therefore it cannot output HDMI audio.
The current HDMI connection does not support Super Audio CDs.
• Please change the method of connection.
Set HDMI output so that it turns on, as explained in the source component’s instruction manual.
Set the resolution so that it matches, as explained in the instruction manuals of both components.
deterioration.
Turn on the power to the unit.
Shut off and then turn the power back on to the unit, TV and source component.
There is nothing wrong with the system. Some HDMI devices require time for authentication.
Set the HDMI audio output so that it turns on, as explained in the source component’s instruction manual.
Set the HDMI audio output so that it can connect to the unit, as explained in the source component’s instruction manual.
• Use a DVD-Audio player that supports CPPM.
• Turn on PCM downsampling on the DVD player.
• Use an analog connection.
Use an analog connection.
ENGLISH
51
ENGLISH
XM SATELLITE RADIO
If a problem should arise, fi rst check the following.
1. Are the connections correct?
2. Have you operated the receiver according to the operating instructions?
3. Are the speakers and other components operating properIy?
If this unit is not operating properly, Check the items listed in the table beIow. Should the problem persist, there may be a malfunction. Disconnect the power immediately and contact your store of purchase.
SYMPTOM CAUSE REMEDY
“ANTENNA” is displayed. XM terminal and the XM Mini-Tuner and Home Dock is not
properly connected.
Check that the connection are correct.
“NO SIGNAL” is displayed. The signal cannot be received. Reposition your XM Mini-Tuner and Home Dock.
Receiving only XM channels 0 and 1.
The XM Tuner is not activated. Contact XM Radio.
Note:
Sometimes, when “PROTECT” is shown on the unit’s display, the standby indicator fl ashes slowly (twice a second). When this happens, turn off the unit’s power and remove the power cable. Then follow the procedure described below:
• Check to ensure that the speaker cables connected to the unit have not been connected with + and - connections reversed.
• Checktoensurethatthespeakercablesconnectedtotheunitarenotshort-circuiting(checktheconnectionsbothontheunitandonthespeakers).
(Check that the playback volume is not greater than the unit can handle.)
• Check that the playback volume is not greater than the unit can handle.
After completing the above checks, connect the power cable and switch the unit back ON using the remote control. Then, after reducing the volume, start playback and check that “PROTECT” is not appearing on the display and that there is no problem with speaker connections to the unit or with sound reproduction. If the same problem re-occurs, please contact your local service center to have it repaired.
On rare occasions, the unit will go into standby mode with the standby indicator fl ashing rapidly (eight times a second). When this happens, it means that some major problem has occurred with the unit. Quickly disconnect the power cable and take the unit to your local service center to have it repaired.
7.1 CH INPUT (SR4002) MULTI (SR5002)
AV SURROUND RECEIVER SR4002
INPUT SELECTOR
S.SPEAKER B
7.1 CH INPUT
STANDBY
SETUP MIC
PHONES
POWER ON/STANDBY
SIMPLE
EXIT ATT
SETUP
VOLUME
UP
DOWN
SIMPLE
PURE
SURROUND
SETUP
DIRECT
MODE
AUTO
HT-EQ
MENU
MEMORY
DISPLAY
ENTER
CLEAR
T-MODE
EXIT
BAND
ATT
MUTE
AUX 1 INPUT
DIGITAL
RLVIDEO
S-VIDEO
AUDIO
FRONT KEY (BUTTON) LOCK OF THE UNIT
If the SIMPLE SETUP and EXT buttons on the front panel are both pressed at the same time for three seconds or more, all the buttons on the front panel, (excluding the POWER ON/OFF button), as well as the INPUT SELECTOR knob and VOLUME knob, will become locked. “F-KEY LOCK!” will appear in the display. Release the lock by pressing the same two keys again at the same time for three seconds or more. “F-KEY UNLOCK” will appear in the display, and the keys will unlock.
GENERAL MALFUNCTION
If the equipment malfunctions, this may be because an electrostatic discharge or AC line interference has corrupted the information in the equipment memory circuits. Therefore:
- disconnect the plug from the AC line supply
- after waiting at least three minutes, reconnect the plug to the AC line supply
- re-attempt to operate the equipment
Memory backup
• In case a power outage occurs or the power cord is accidentally unplugged, this unit is equipped with a backup function to prevent memory data such as the preset memory from being erased.
52
HOW TO RESET THE UNIT
Should the operation or display seem to be abnormal, reset the unit with the following procedure. To turn on the SR4002, press and hold the 7.1CH INPUT and ATT buttons simultaneously for 3 seconds or more. To turn on the SR5002, press and hold the MULTI and ATT buttons simultaneously for 3 seconds or more. Remember that the procedure will reset the settings of the SOURCE, Surround mode, delay time, TUNER
TECHNICAL SPECIFICATIONS
Frequency Range ...................................87.5 – 108.0 MHz
Usable Sensitivity ................................IHF 1.8 µV/16.4 dBf
Signal to Noise Ratio ......................Mono/Stereo 75/70 dB
Distortion ........................................ Mono/Stereo 0.2/0.3 %
Stereo Separation ............................................1 kHz 45 dB
Alternate Channel Selectivity ....................± 300 kHz 60 dB
Image Rejection ............................................98 MHz 70 dB
Tuner Output Level ..............1 kHz, ± 75 kHz Dev 800 mV
AM TUNER SECTION
Frequency Range ......................................520 – 1710 kHz
Signal to Noise Ratio ................................................. 50 dB
Usable Sensitivity .........................................Loop 400µV/m
Distortion ..................................... 400Hz, 30 % Mod. 0.5 %
Selectivity ....................................................± 20 kHz 70 dB
AUDIO SECTION (SR4002)
Power Output (20 Hz – 20 kHz/THD=0.08%)
Front L&R ................................................8 ohms 80 W / Ch
Center .....................................................8 ohms 80 W / Ch
Surround L&R .........................................8 ohms 80 W / Ch
Surround Back L&R ................................8 ohms 80 W / Ch
Front L&R ............................................. 6 ohms 105 W / Ch
Center .................................................. 6 ohms 105 W / Ch
Surround L&R ...................................... 6 ohms 105 W / Ch
Surround Back L&R ............................. 6 ohms 105 W / Ch
Input Sensitivity/Impedance ..................180 mV/ 47 Kohms
Signal to Noise Ratio(Analog Input / Pure Direct) ....... 105 dB
Frequency Response (Analog Input / Pure Direct)
..............................................8 Hz – 100 kHz (± 3 dB)
(Digital Input / 96 kHz PCM)
............................................... 8 Hz – 45 kHz (± 3 dB)
AUDIO SECTION (SR5002)
Power Output (20 Hz – 20 kHz/THD=0.08%)
Front L&R ................................................8 ohms 90 W / Ch
Center .....................................................8 ohms 90 W / Ch
Surround L&R .........................................8 ohms 90 W / Ch
Surround Back L&R ................................8 ohms 90 W / Ch
Front L&R ..............................................6 ohms 110 W / Ch
Center ...................................................6 ohms 110 W / Ch
Surround L&R .......................................6 ohms 110 W / Ch
Surround Back L&R ..............................6 ohms 110 W / Ch
Input Sensitivity/Impedance ..................180 mV/ 47 Kohms
Signal to Noise Ratio(Analog Input / Pure Direct) ....... 105 dB
Frequency Response (Analog Input / Pure Direct)
..............................................8 Hz – 100 kHz (± 3 dB)
(Digital Input / 96 kHz PCM)
................................................8 Hz – 45 kHz (± 3 dB)
VIDEO
Television Format ....................................................... NTSC
Input Level/Impedance ..............................1 Vp-p/75 ohms
Output Level/Impedance ...........................1 Vp-p/75 ohms
Video Frequency Response ..........5 Hz to 8 MHz (– 1 dB)
Video Frequency (Component)
.......5 Hz to 80 MHz (– 1 dB)
S/N ............................................................................. 60 dB
GENERAL (SR4002)
Power Requirement ....................................AC 120 V 60Hz
Power Consumption ................................................. 450 W
Weight .................................................... 25.1 lbs (11.4 Kg)
GENERAL (SR5002)
Power Requirement ....................................AC 120 V 60Hz
Power Consumption ................................................. 500 W
Weight .................................................... 27.1 lbs (12.3 Kg)
ACCESSORIES
Remote Controller RC5001SR .......................................... 1
AAA-size batteries ............................................................ 2
FM Antenna ........................................................................1
AM Loop Antenna ..............................................................1
Front AUX Jack Cover .......................................................1
AC Power Cord ..................................................................1
Microphone MC-10 ............................................................1
User Guide .........................................................................1
Warranty Card (USA x 1, Canada x 1)
DIMENSIONSFM TUNER SECTION
17-5/16 ins. (440 mm)
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
SIMPLE
PURE
SURROUND
MODE
POWER ON/STANDBY
MULTI SPEAKER
MULTI
STANDBY
SETUP MIC
PHONES
SETUP
DIRECT
AUTO
HT-EQ
MENU
MEMORY
DISPLAY
ENTER
EXIT
BAND
Specifi cations subject to change without prior notice.
VOLUME
UP
DOWN
CLEAR
T-MODE
ATT
MUTE
AUX 1 INPUT
DIGITAL
RLVIDEO
S-VIDEO
AUDIO
(23 mm)
29/32 ins.
(341 mm)
13-7/16 ins.
(20 mm)
13/16 ins.
5-3/4 ins.
(146 mm)
(14 mm)
9/16 ins.
(384 mm)
15-1/8 ins.
(160 mm)
6-5/16 ins.
ENGLISH
53
SETUP CODES
TV
Acer .......................................................... 1141
Admiral .................................1002, 1009, 1089
Aiko ..........................................................1059
Aiwa ................................................1117, 1118
Akai ..........................................................1001
Amtron ...................................................... 1023
Anam ........................................................ 1113
Anam National ......................1023, 1069, 1092
AOC ........................... 1003, 1024, 1049, 1127
Audiovox ................................................... 1023
Bell & Howell ..................................1009, 1025
Benq ............................................... 1104, 1142
Broksonic .................. 1003, 1097, 1098, 1113
Celebrity ................................................... 1001
Citizen ..................................1003, 1013, 1023
1026, 1059, 1063
Colortyme ....................................... 1003, 1043
Contec ...................................................... 1113
Contec/Cony ........................1023, 1045, 1047
Craig .......................... 1020, 1022, 1023, 1113
Crown .............................................1023, 1067
Curtis Mathes .......................1003, 1013, 1025
1026, 1062, 1103, 1110
Daewoo ..................... 1003, 1013, 1024, 1035
1036, 1059, 1084, 1101
Daytron .................................1003, 1013, 1016
Dimensia ........................................1103, 1110
Dumont .................................1003, 1010, 1153
Electroband .............................................. 1001
Electrohome .............. 1001, 1003, 1069, 1133
Emerson ...............................1003, 1013, 1015
1020, 1021, 1022, 1023 1025, 1038, 1044, 1045 1048, 1055, 1061, 1094 1096, 1099, 1101, 1113
Envision .................................................... 1003
Fisher ........................ 1025, 1051, 1091, 1160
Fujitsu ........................ 1038, 1124, 1125, 1155
Funai ....................................1023, 1038, 1113
Gateway ...................................................1150
GE ............................ 1003, 1018, 1022, 1046
1054, 1069, 1085, 1103 1110, 1113, 1133, 1136, 1153
Goldstar ................................1003, 1013, 1024
1030, 1045, 1080
Hallmark ................................................... 1003
Hisense ....................................................1116
Hitachi ....................... 1003, 1012, 1031, 1032
1037, 1041, 1045, 1047 1065, 1068, 1082, 1088 1094, 1139, 1140, 1145, 1159
Infi nity ....................................................... 1067
Janeil ........................................................ 1134
JBL ........................................................... 1067
JC Penney ............................1003, 1013, 1018
1019, 1024, 1026 1046, 1047, 1054 1063, 1083, 1085 1100, 1103, 1110 1112, 1133, 1154
Jensen ...................................................... 1003
JVC .......................................1028, 1029, 1045
1047, 1050, 1060, 1065
Kawasho .........................................1001, 1003
Kenwood ..................................................1003
Kloss Novabeam ....... 1023, 1056, 1057, 1134
KTV ......................................1013, 1023, 1033
1034, 1073, 1099, 1113
LG ...................................................1024, 1030
M.Wards ...............................1002, 1009, 1038
Magnavox .............................1003, 1052, 1053
1056, 1057, 1063 1067, 1081, 1106
Marantz ..................... 1003, 1031, 1067, 1122
Mitsubishi .............................1003, 1024, 1051
1115, 1122, 1133
Motorola .........................................1014, 1069
NEC ................. 1003, 1012, 1024, 1043, 1069
NET-TV ........................................... 1137, 1150
Orion ...............................................1020, 1096
Panasonic ........ 1017, 1067, 1069, 1095, 1111
Philips ........................ 1003, 1011, 1045, 1052
1054, 1056, 1057, 1058 1063, 1067, 1069, 1106
Pioneer .................................1003, 1018, 1037
1070, 1071, 1094 1145, 1147, 1149
Plasmsync ................................................ 1135
Portland ..................... 1003, 1013, 1024, 1059
Price Club ................................................. 1026
Prism ........................................................ 1018
1100, 1112, 1154
Proscan ..................... 1004, 1005, 1006, 1007
1008, 1085, 1103, 1110
Proton ............................................. 1003, 1045
Quasar ............ 1010, 1069, 1073, 1111, 1153
Radio Shack .........................1003, 1013, 1015
1023, 1024, 1025, 1045 1100, 1103, 1110, 1113
RCA ......................................1003, 1004, 1005
1006, 1007, 1008 1014, 1024, 1049, 1069 1075, 1079, 1085, 1087 1088, 1093, 1094, 1101 1103, 1110, 1113, 1153
Realistic ..................... 1013, 1015, 1023, 1025
1045, 1100, 1103, 1110
Runco ............................................. 1010, 1153
Sampo ...................................................... 1150
Samsung ................... 1003, 1013, 1024, 1026
1040, 1045, 1062, 1078 1083, 1090, 1100, 11051114 1120, 1121, 1146, 1148, 1157
Sansui ......................................................1119
Sanyo ........................ 1003, 1025, 1051, 1072
1077, 1091, 1156, 1157, 1158
Sharp ....................................1003, 1013, 1014
1015, 1045, 1055, 1064 1066, 1076, 1089, 1123
Signature .................................................. 1009
Sony .....................................1001, 1102, 1108
Soundesign ..... 1003, 1023, 1038, 1063, 1113
Starlite ...................................................... 1023
Supre-Macy .............................................. 1134
Sylvania ................................1003, 1039, 1042
1052, 1053, 1056, 1057 1063, 1067, 1089, 1151
Symphonic ...........................1023, 1039, 1044
Tandy ........................................................ 1014
Tatung ....................................................... 1069
Technics ...................................................1018
Techwood ....................................... 1003, 1018
Teknika ...................... 1003, 1009, 1013, 1023
1024, 1026, 1038, 1045 1047, 1059, 1063, 1111, 1113
Telecaption ............................................... 1074
Toshiba .................................1003, 1019, 1025
1026, 1042, 1074, 1098 1107, 1111, 1135, 1136
Totevision .................................................1013
Universal ........................................1046, 1054
Video Concepts ........................................ 1113
Viewsonic .............................1006, 1022, 1109
1128, 1129, 1130, 1131 1138, 1143, 1145, 1150
Wards ...................................1003, 1009, 1015
1024, 1038, 1044, 1046 1052, 1054, 1056, 1057 1067, 1086, 1103, 1110
White Westinghouse ......................1001, 1101
Yamaha ..........................................1003, 1024
Zenith ...................................1003, 1009, 1010
1132, 1144, 1153
VCR
Admiral ...........................................3026, 3060
Adventura ................................................. 3035
Aiko ..........................................................3038
Aiwa ................................................3035, 3039
Akai ................................................3003, 3053
3054, 3072, 3073
American High .........................................3009
Asha ......................................................... 3021
Audio Dynamics ...................3034, 3040, 3083
Audiovox ................................................... 3052
Beaumark ....................................... 3017, 3021
Bell & Howell ............................................3029
Broksonic .......................................3029, 3075
Calix .........................................................3052
Candle ..................................3012, 3021, 3034
3038, 3050, 3052, 3056
Canon ............................................. 3008, 3009
Capehart .................................................. 3050
Carver .............................................3045, 3062
CCE ................................................ 3038, 3067
Challenger ................................................ 3078
Citizen ............. 3012, 3021, 3038, 3052, 3056
Colortyme ....................................... 3034, 3079
Colt ........................................................... 3067
Craig .......................... 3021, 3032, 3052, 3067
Criterion .................................................... 3067
Curtis Mathes .................................3008, 3009
3021, 3034, 3063
Cybernex .................................................. 3021
Daewoo ................................3035, 3038, 3050
Daytron ...........................................3038, 3050
DBX ......................................3034, 3040, 3083
Denon ....................................................... 3005
i
Dimensia ..............................3004, 3063, 3085
Dixon ..............................................3077, 3081
Dynatech .................................................. 3035
Electrohome ............................................. 3052
Electrophonic ...........................................3052
Emerson .................... 3009, 3015, 3016, 3017
3018, 3019, 3022, 3035 3047, 3052, 3054, 3073
Fisher .............................................3029, 3032
Fuji .................................................. 3003, 3009
Funai ..............................................3035, 3056
Garrard ..................................................... 3035
GE ........................................3004, 3008, 3009
3021, 3028, 3058 3063, 3074, 3085
Go Video ..............................3021, 3036, 3037
3052, 3067, 3068, 3069
Goldstar ..................... 3021, 3031, 3034, 3052
Gradiente .......................................3035, 3052
Harley Davidson ....................................... 3035
Harman Kardon ..............................3034, 3045
Harwood ................................................... 3067
Headquarter ............................................. 3029
Hitachi ............. 3004, 3005, 3055, 3072, 3074
Homeline .................................................. 3052
Instant Replay .......................................... 3009
JBL ........................................................... 3002
JC Penney ................. 3005, 3008, 3009, 3017
3021, 3029, 3034, 3040 3052, 3062, 3067, 3083
JCL ........................................................... 3009
Jensen ............................................ 3005, 3072
JVC .......................................3014, 3015, 3034
3040, 3041, 3042 3048, 3049, 3072, 3083
Kenwood ................... 3029, 3034, 3048, 3072
KLH ..........................................................3067
Kodak .............................................3009, 3052
LG ...................................................3031, 3052
Lloyds ...................................3034, 3035, 3056
Logik ......................................................... 3067
LXI ............................................................ 3052
Magnasonic ..........................3038, 3052, 3067
Magnavox .............................3008, 3009, 3010
3045, 3067, 3071
Magnin ...........................................3021, 3052
Marantz ................................3009, 3029, 3034
3040, 3045, 3062, 3083
Marta ........................................................ 3052
MEI ........................................................... 3009
Memorex ..............................3005, 3009, 3021
3026, 3029, 3032, 3035 3052, 3060, 3067, 3071
MGA ...............................................3022, 3073
MGN Technology ......................................3021
Midland ..................................................... 3056
Minolta ...................................................... 3005
Mitsubishi .............................3005, 3022, 3023
3025, 3048, 3052, 3073
Montgomery Ward ..........................3026, 3060
Motorola ...............................3009, 3026, 3060
MTC ................................................3021, 3067
Multitech ...............................3021, 3035, 3067
NEC ......................................3033, 3034, 3040
3048, 3072, 3083
Nikko ........................................................3052
Noblex ......................................................3021
Olympus ................................................... 3009
Optimus ................................3026, 3052, 3060
Optonica ................................................... 3027
Orion .......................... 3015, 3017, 3047, 3052
Panasonic ........ 3006, 3007, 3008, 3009, 3067
Pentax ..................................3005, 3034, 3074
Philco ............... 3005, 3008, 3009, 3047, 3062
Philips .............. 3009, 3010, 3027, 3045, 3062
Pilot ..........................................................3052
Pioneer .................................3005, 3040, 3046
3048, 3061, 3080, 3083
Portland .................................................... 3050
Proscan ................................3004, 3063, 3085
Protec ....................................................... 3067
Proton ....................................................... 3067
Pulsar ........................ 3021, 3038, 3056, 3071
Quarter ........................................... 3029, 3084
Quartz ............................................3029, 3084
Quasar ...........................................3008, 3009
Radio Shack .............. 3021, 3052, 3009, 3008
3035, 3027, 3060, 3026
Radix ........................................................ 3052
Randex ..................................................... 3052
RCA ......................................3004, 3005, 3009
3021, 3046, 3054, 3057 3061, 3063, 3074, 3085
Realistic ..................... 3008, 3009, 3012, 3021
3026, 3027, 3029, 3032 3035, 3052, 3060, 3084
Ricoh ..............................................3002, 3059
Runco ....................................................... 3071
Samsung ..............................3013, 3020, 3021
3056, 3068, 3069, 3070
Sanky ...................................3026, 3060, 3071
Sansui ............. 3040, 3048, 3067, 3072, 3083
Sanyo ...................................3021, 3029, 3032
Scott .......................... 3012, 3017, 3022, 3052
Sears ....................................3005, 3009, 3029
3032, 3034, 3052, 3084
Sharp ......................... 3026, 3027, 3060, 3064
Shintom ................................3003, 3005, 3067
Shogun ..................................................... 3021
Signature ........................................ 3026, 3060
Signature 2000 .....................3026, 3029, 3084
Singer ........................ 3002, 3009, 3059, 3067
Sony .......................... 3001, 3003, 3043, 3065
STS ................................................3005, 3009
Sylvania ................................3008, 3009, 3022
3035, 3045, 3062, 3076
Symphonic ...........................3034, 3035, 3056
Tandy .............................................. 3029, 3084
Tashiko .....................................................3052
Tatung ....................................................... 3072
Teac ................................................ 3035, 3072
Technics .........................................3007, 3009
Teknika .................................3009, 3035, 3052
TMK .......................................................... 3021
Toshiba .................................3005, 3011, 3012
3022, 3051, 3073
Totevision .......................................3021, 3052
Unitec ....................................................... 3056
Unitech ..................................................... 3021
Vector Research ........ 3012, 3034, 3040, 3083
Victor ..............................................3040, 3083
Video Concepts ..............................3012, 3034
3040, 3073, 3083
Videosonic ................................................3021
Wards ...................................3005, 3009, 3012
3021, 3026, 3027 3032, 3035, 3045 3052, 3060, 3061, 3067
White Westinghouse ......................3035, 3056
XR-1000 ...............................3009, 3035, 3067
Yamaha ................................3029, 3034, 3040
3072, 3083, 3084
Zenith .............. 3030, 3052, 3053, 3059, 3071
DVD
Aiwa ................................................2036, 2037
Apex ...... 2012, 2017, 2018, 2019, 2021, 2034
BOSE .............................................2038, 2039
Denon ............................................. 2047, 2048
Funai ........................................................2049
GE ............................. 2009, 2020, 2029, 2033
Harman Kardon ........................................ 2061
Hitachi ..................................2008, 2012, 2031
JVC .......................................2006, 2010, 2040
2041, 2042, 2043
Kenwood ........................................2053, 2054
Koss ..........................................................2058
Magnavox .................. 2007, 2011, 2023, 2025
Marantz ....................................................2025
Mitsubishi .......................................2011, 2015
Onkyo ....................................................... 2062
Oritron ............................................2009, 2030
Panasonic .................. 2003, 2015, 2016, 2055
Philips ...................................2007, 2011, 2058
Pioneer .................................2002, 2014, 2056
Proscan ................................2009, 2020, 2032
RCA ................. 2005, 2009, 2020, 2035, 2057
Sampo ...................................................... 2041
Samsung ......... 2008, 2012, 2022, 2024, 2027
Sanyo .............................................2050, 2052
Sharp ..............................................2044, 2045
Sherwood ................................................. 2051
Sony .....................................2001, 2013, 2059
Toshiba ...................... 2004, 2008, 2026, 2028
Yamaha ..........................................2046, 2060
Zenith .......................................................2010
DSS
Alphastar .................................................. 4027
BSB .......................................................... 4021
Chaparral .................................................4039
DIRECTV .......................................4001, 4016
DISH Network ..........................................4030
Drake ........................................................ 4026
Echostar .......... 4007, 4017, 4018, 4019, 4020
Express Vu ............................................... 4017
Fujitsu ....................................................... 4025
GE ........................................4002, 4008, 4009
General Instruments ......................4036, 4037
Hitachi ............................................4001, 4015
ii
Hughes ........................................... 4001, 4016
Janeil ........................................................ 4025
JVC ........................................................... 4017
Mitsubishi .................................................4001
Panasonic .......................................4004, 4010
Philips ............................................. 4031, 4035
Proscan ..................... 4002, 4008, 4009, 4011
Radio Shack ...................................4036, 4037
RCA ........................... 4002, 4008, 4009, 4029
Realistic .................................................... 4040
Rural Cable .............................................. 4036
Samsung ........................................ 4022, 4027
Sony .....................................4003, 4012, 4014
Star Choice ..............................................4032
Star Trak ...................................................4024
STS ..........................................................4038
SuperDish ................................................4028
Toshiba ........................................... 4001, 4034
Uniden ..................................4005, 4006, 4013
Video Pall .................................................4025
Zenith .............................................4025, 4033
iii
www.marantz.com
You can find your nearest authorized distributor or dealer on our website.
is a registered trademark.
07/2007 00M32CW851250 mzh-dPrinted in China
Loading...