Please use this service manual with referring to the user guide (D.F.U) without fail.
- CD4000 -
272W855010 AO
3120 785 00040
First Issue:1999.06
MARANTZ DESIGN AND SERVICE
Using superior design and selected high grade components, MARANTZ company has created the ultimate in stereo sound.
Only original
it is famous.
Parts for your
ORDERING PARTS :
Parts can be ordered either by mail or by Fax.. In both cases, the correct part number has to be specified.
The following information must be supplied to eliminate delays in processing your order :
1. Complete address
2. Complete part numbers and quantities required
3. Description of parts
4. Model number for which part is required
5. Way of shipment
6. Signature : any order form or Fax. must be signed, otherwise such part order will be considered as null and void.
MARANTZ parts can insure that your MARANTZ product will continue to perform to the specifications for which
MARANTZ equipment are generally available to our National Marantz Subsidiary or Agent.
SUPERSCOPE TECHNOLOGIES, INC.SUPERSCOPE TECHNOLOGIES, INC.
MARANTZ PROFESSIONAL PRODUCTS
2640 WHITE OAK CIRCLE, SUITE A
AURORA, ILLINOIS 60504 USA
PHONE : 630 - 820 - 4800
FAX : 630 - 820 - 8103
CAUTION : After servicing this appliance and prior to returning to customer, measure the resistance between either primary AC
cord connector pins ( with unit NOT connected to AC mains and its Power switch ON ), and the face or Front Panel of product and
controls and chassis bottom.
Any resistance measurement less than 1 Megohms should cause unit to be repaired or corrected before AC power is applied, and
verified before it is return to the user/customer.
Ref. UL Standard No. 1492.
In case of difficulties, do not hesitate to contact the Technical
Department at above mentioned address.
990521A.O
2-1
General
Dimensions (WxHxD): 435 x 86 x 265mm
Weight: 2,9kg
Number of channels: 2
Output voltage (Line out): 2V
RMS
3dB
Unbalance left-right: 1dB
Frequency response: 20Hz-20kHz 0,4dB
Signal to noise ratio: 98 dB typ.
Dynamic range: 95dB typ. at 1kHz
THD: 0,0063% at 1kHz
Channel separation: 85dB typ. at 1kHz
All ICs and many other semiconductors are susceptible to
electrostatic discharges (ESD). Careless handling during
repair can reduce life drastically.
When repairing, make sure that you are connected with the
same potential as the mass of the set via a wristband with
resistance. Keep components and tools at this potential.
ATTENTION
Tous les IC et beaucoup d´autres semi-conducteurs sont
sensibles aux décharges statiques (ESD). Leur longévite
pourrait être considérablement écourtée par le fait qu´aucune
précaution nést prise à leur manipulation.
Lors de réparations, s´assurer de bien être relié au même
potentiel que la masse de l´appareil et enfileer le bracelet
serti d´une résistance de sécurité.
Veiller à ce que les composants ainsi que les outils que l´on
utilise soient également à ce potentiel.
WARNUNG
Alle ICs und viele andere Halbleiter sind empfindlich
gegenüber elektrostatischen Entladungen (ESD).
Unsorgfältige Behandlung im Reparaturfall kann die
Lebensdauer drastisch reduzieren.
Sorgen Sie dafür, daß sie im Reparaturfall über ein Pulsarmband mit Widerstand mit dem Massepotential des
Gerätes verbunden sind.
Halten Sie Bauteile und Hilfsmittel ebenfalls auf diesem
Potential.
AVAILABLE ESD PROTECTION EQUIPMENT :
anti-static table mat large 1200x650x1.25mm4822 466 10953
anti-static wristband4822 395 10223
connection box (3 press stud connections, 1M )4822 320 11307
extendible cable (2m, 2M , to connect wristband to connection box)4822 320 11305
connecting cable (3m, 2M , to connect table mat to connection box)4822 320 11306
earth cable (1M , to connect any product to mat or to connection box) 4822 320 11308
KIT ESD3 (combining all 6 prior products - small table mat)4822 310 10671
wristband tester4822 344 13999
AVAILABLE JIG for FR980
Extension PCB and wire kit4822 395 10815
ESD
WAARSCHUWING
Alle IC´s en vele andere halfgeleiders zijn gevoelig voor
electrostatische ontladingen (ESD).
Onzorgvuldig behandelen tijdens reparatie kan de levensduur
drastisch doen vermindern. Zorg ervoor dat u tijdens reparatie
via een polsband met weerstand verbonden bent met hetzelfde
potentiaal als de massa van het apparaat.
Houd componenten en hulpmiddelen ook op ditzelfde potentiaal.
AVVERTIMENTO
Tutti IC e parecchi semi-conduttori sono sensibili alle scariche
statiche (ESD).
La loro longevità potrebbe essere fortemente ridatta in caso di
non osservazione della più grande cauzione alla loro
manipolazione. Durante le riparationi occorre quindi essere
collegato allo stesso potenziale che quello della massa
delápparecchio tramite un braccialetto a resistenza.
Assicurarsi che i componenti e anche gli utensili con quali si
lavora siano anche a questo potenziale.
small 600x650x1.25mm4822 466 10958
Safety regulations require that the set be restored to its
original condition and that parts which are identical with
those specified be used.
Safety components are marked by the symbol
Les normes de sécurité exigent que l`appareil soit remis
à l`état d`origine et que soient utilisées les pièces de
rechange identiques à celles spécifiées.
Les composants de sécurité sont marqués
DANGER: Invisible laser radiation when open.
AVOID DIRECT EXPOSURE TO BEAM.
Varning !
Advarsel !
Osynlig laserstrålning när apparaten är öppnad och
spärren är urkopplad. Betrakta ej strålen.
Bei jeder Reparatur sind die geltenden Sicherheitsvorschriften zu beachten. Der Originalzustand des Gerätes
darf nicht verändert werden. Für Reparaturen sind Originalersatzteile zu verwenden.
Sicherheitsbauteile sind durch das Symbol markiert.
LASER PRODUCT
Usynlig laserstråling ved åbning når sikkerhedsafbrydere
er ude af funktion. Undgå udsaettelse for stråling.
SAFETY
Veiligheidsbepalingen vereisen, dat het apparaat in zijn
oorspronkeliijke toestand wordt teruggebracht en dat
onderdelen, identiek aan de gespecificeerde, worden toegepast.
De Veiligheidsonderdelen zijn aangeduid met het symbool
Le norme di sicurezza estigono che l´apparecchio venga
rimesso nelle condizioni originali e che siano utilizzati i
pezzi di ricambiago identici a quelli specificati.
Componenty di sicurezza sono marcati con
CLASS 1
Varoitus !
Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiina
näkymättömälle laserisäteilylle. Älä katso säteeseen !
After servicing and before returning the set to customer
perform a leakage current measurement test from all
exposed metal parts to earth ground, to assure no
shock hazard exists.
The leakage current must not exceed 0.5mA.
CS 53 103
"Pour votre sécurite, ces documents doivent être utilisés par
des spécialistes agréés, seuls habilités à réparer votre
appareil en panne".
4-1
CS 53 108
MECHANICAL INSTRUCTIONS
1) Loosen 7x screw as shown in picture 1.
picture 1
picture 2
2) Lift top cover as shown in picture 2.
3) Remove top cover.
Dismantling Top Cover
MECHANICAL INSTRUCTION
Dismantling Front
1) Press open/close button to open the tray. If the tray doesnít
work, turn counterclockwise a small screwdriver into the
hole as shown in picture 3. Then the tray comes out. After
the first centimeter it is possible to pull the tray out by
hand.
2) Release the door cover of the tray as shown in picture 4.
3) Loosen 2x screw as shown in picture 5.
4) Release 2x snap on button (see picture 5).
5) Release 2x snap on side (see picture 6).
6) Remove front.
4-2
Picture 3
Picture 4
3
3
44
Picture 5
Bottom view
Picture 6
5
Side view
4-3
CS 53 110
Dismantling hints CD Short Loader
Dismantling the tray
a) Press open/close button to open the tray. If the tray
doesn´t work, use a small screwdriver as shown in Fig.1
point 1 to move the tray outside. After the first centimetre
it is possible to pull the tray out by hand.
b) Release two snaps and remove tray.
Fig. 1
4-4
CS 53 111
Assembly of gear
a) Use a pin (e.g. a paperclip) to align the cam wheel (a)
withthe gear wheel (b). See Fig. 2.
b) Fix the wheels with the small plastic whashers.
Fig. 2
4-5
CS 53 112
c) Mount idle wheel 2 (c) and idle wheel 1 (d) in any
position. See Fig. 3.
d) Fix the idle wheel 1 (d) with the small plastic whasher.
e) Mount the driving belt.
f) Mount the pinion guiding assy and the cover as shown in
Fig. 4.
g) Turn the gear wheel (b) counter clockwise to
endposition.
Check if tray mechanism works correctly!
1) Turn the gear wheel (b) clockwise to its endposition
(Use a small screwdriver as shown in Fig. 1 point 1).
The tray has to move to inner position first and then the
CD mechanism has to move to its upper position.
2) Turn the gear wheel (b) counter clockwise to its
endposition.
The CD Mechanism has to move to its lower position first
and then the tray has to move outside.
h) Mount the CD Mechanism as shown in Fig. 5.
i) Mount the tray (Align the tray to the chassis and push it
inside).
Fig. 3
Fig. 4
Fig. 5
5-1
CS 53 113
HANDLING CHIP COMPONENTS
SERVICE TOOLS
TORX T10 screwdriver with shaftlength 150mm ......................................4822 395 50423
TORX screwdriver set SBC 163 ..............................................................4822 295 50145
Audio signal disc SBC 429......................................................................4822 397 30184
Playability test disc SBC444...................................................................4822 397 30245
Test disc 5(disc without errors) +
Test disc 5A (disc with dropout errors, black spots and fingerprints)
Burn in test disc (65 min. 1kHz signal at -30dB level without "pause") ...4822 397 30155
5-25-2
CS 53 114
N
Y
Y
N
TIME
Button pressed?
YN
TIME
Button pressed?
TIME
Button pressed?
DISPLAY
TEST
DISPLAY TEST
Fig. 1
Fig. 2
Display shows Fig. 1
Display shows Fig. 2
PROGRAM
EDIT
PEAK
REPEATREMTOTALTIME1 2 3 4
5678
9 101112
13 14 15 +
TRACKSHUFFLE1
PROG
EDIT
TOT1 2 3 4
5678
9 101112
13 14 15 +
TRACSHUFFLE1
NEXT
Button pressed?
Y
N
FOR CD TEST
see next page
Display becomes dark
Set is in stand by
PLAY
Button pressed?
Y
N
Set works as in normal Mode.
In case of failures error codes
according table 2 will be
displayed.
The CD PLAY Test is intended
to be used for continuously playing
a disc in order to detect intermittend
or not reproducible failures.
The error code indicates where the
failure can be found.
CD
TEST
CD PLAY
TEST
Table 2
CD PLAY TEST
SERVICE TEST PROGRAM
W = Warning
Error number remains on display till next warning/error
F = Fatal error
Set stops playing → Error number remains on display
PROGRAM
Button pressed?
Y
Y
N
N
STOP
Button pressed?
Display shows
8M
Output at
pin80 of 7800=1953,125Hz
QUARTZ
TEST
SHUFFLE
Button pressed?
Y
N
STOP
Button pressed?
Y
N
KEY
TEST
Y
N
any key pressed?
Display shows "--"
Display shows
corresponding key number
(see table 1)
Table 1
KEY TEST
To start service test
program hold
PLAY & STOP depressed
while plugging in
the mains cord
Display shows number of
ROM version
"S Vzz"
S stands for Service Testprogram
V stands for Software Version
In case of focus lost FOC ERR
will be displayed and
Focus Servo Test is entered again
It is possible to control the
slide motor with the
NEXT & PREV button
SERVICE TEST PROGRAM CD-Part
STP-CD Part CD713/CD723 (980429)
Since the CD-RW reflects much less light than an ordinary
CD-A, the gain of the HF-amplifier stage and the sensitivity
of the ADC inside the signal processor must be increased.
The gain is switched via the HG line (pin41 of CD7), the
ADC-sensitivity is switched via software (µP → CD7).
During start-up the correct mode is choosen automatically;
in the service test program it can be switched manually in
order to allow individual measurements in both conditions.
1VSSA1GNDsupply (analog) of CD7
2VDDA1+4Vsupply (analog) of CD7
3D1HF-preamp → CD7unipolar current input (central diode signal input)
4D2HF-preamp → CD7unipolar current input (central diode signal input)
5D3HF-preamp → CD7unipolar current input (central diode signal input)
6VRLGNDreference input for ADC
7D4HF-preamp → CD7unipolar current input (central diode signal input)
8R1HF-preamp → CD7unipolar current input (satellite diode signal input)
9R2HF-preamp → CD7unipolar current input (satellite diode signal input)
10IREFT→ CD7current reference for calibration ADC
11VRHnot connectedreference output from ADC
12VSSA2GNDsupply (analog) of CD7
13SELPLL+4Vselects whether internal clock multiplier PLL is used
14ISLICECD7 →current feedback from data slicer
15HFIN→ CD7comparator signal input
16VSSA3GNDsupply (analog) of CD7
17HFREF→ CD7comparator common mode input
18IREF→ CD7reference current pin (nom. VDD/2)
19VDDA2+4Vsupply (analog) of CD7
20TEST1GNDtest control input
21CRINX-Tal → CD7crystal/resonator input
22CDOUTX-Tal → CD7crystal/resonator output
23TEST2GNDtest control input
24CL16not connected16.9344MHz system clock output
25CL11not connected11.2896MHz or 5.6448MHz clock output (3-state)
26RACD7 → servo driverradial actuator output
27FOCD7 → servo driverfocus actuator output
28SLCD7 → servo driverslide actuator output
29TEST3GNDtest control input
30VDD1P+4Vsupply (digital) of CD7
31DOBMCD7 → digital outputbi-phase mark output (3-state)
32VSS1GNDsupply (digital) of CD7
33MOTO1CD7 → servo drivermotor output1 of CD7; versatile (3-state)
34MOTO2CD7 → servo drivermotor output2 of CD7; versatile (3-state)
35SBSYnot connectedsubcode block sync (3-state)
36SFSYnot connectedsubcode frame sync (3-state)
37RCKGNDsubcode clock input
38SUBnot connectedP to W subcode bits (3-state)
39VSS2GNDsupply (digital) of CD7
40V5not connectedversatile output pin of CD7
41V4not connected versatile output pin of CD7
42V3not connectedversatile output pin of CD7 (open drain)
43KILLCD7 →kill output; programmable (open drain)
44MISCnot connectedC2 error flag; output only defined in CD-ROM modes (3-state)
45DATACD7 → DACserial data output (3-state)
46WCLKCD7 → DACword clock output (3-state)
47VDD2P+4Vsupply (digital) of CD7
48BCLKCD7 → DACserial bit clock output (3-state)
49VSS3GNDsupply (digital) of CD7
50CL4not connected4.2336MHz µP clock output
51SDAµP → CD7µP interface data I/O line (open drain output)
52SCLµP → CD7µP interface clock line
53RABµP → CD7µP interface R/W and load control line
54SILDµP → CD7µP interface R/W and load control line
55NCno connection
56VSS4GNDsupply (digital) of CD7
57RESETµP → CD7power-on reset input (active low)
58STATUSnot connectedservo interrupt request line/CD7 status register output (open drain)
59VDD3C+4Vsupply core (digital)
60C2FAILnot connectedindication of correction failure (open drain)
61CFLGnot connectedcorrection flag output (open drain)
62V1→ CD7versatile input pin
63V2→ CD7versatile input pin
64LDONCD7 → 7820laser drive on output (open drain)
This assembly drawing shows a summary of all possible versions.
For components used in a specific version
see schematic diagram respectively partslist.
AF Board stage .6 19990505
7-3
7-3
1251 B1
1252 F14
1502 F4
1503 G7
1504 D14
1506 B14
1507 B3
2500 B2
2502 B5
2509 C9
2510 D9
2511 B10
2512 E10
2513 D13
2514 E13
2521 A9
2522 F9
2523 C1
2524 B7
2529 B9
2530 E8
2531 B6
2541 F5
2542 G5
2543 G6
3500 D2
3501 D3
3502 B3
3503 C3
3504 C3
3505 B5
3506 B7
3507 B7
3511 C9
3512 D9
3513 B11
3514 E11
3527 C10
3532 D11
3534 C10
3535 D2
3537 A9
3538 E9
3539 B12
3540 C12
3541 D12
3542 E12
3543 B12
3544 D12
3545 C12
3547 E12
3548 E3
3556 G6
5801 F5
6500 D11
7500 C2
7501 E2
7502 C6
7504 D11
7505-A E9
7505-B B9
7507 B13
7508 C13
7509 D13
7510 E13
F510 B1
F511 B1
F512 B1
F513 C1
F514 C1
F515 C1
F516 C1
F517 E2
F518 B6
F519 B7
F521 D8
F522 D8
F525 B14
F526 B14
F527 C14
F528 C14
F529 C14
F530 D14
F531 D14
F532 D14
F540 F4
F541 G4
F542 G4
F543 F6
F544 G6
F550 G14
F551 G14
F552 G14
F553 G14
F554 G14
F555 G14
F556 G14
F557 H14
1234567891011121314
AF Board / DAC part
A
TRANSFER OF AUDIO SAMPLES VIA SERIAL INTERFACE
left channel
MSB
CLOCK
WORD SELECT
DATA
CLOCK
WORD SELECT
DATA
LSB
right channel
MSB
LSB
4.23MHz
176.4kHz
TB 0.5 s/Div
+5V
3505
100R
2502
1
2
3
2531
220u
D1
FREQUENCY
DIVIDER
CONTROL
AND
TIMMING
F518F519
22n
A
7502
TDA1545A
VDD
LEFT
CHANNEL
REGISTER
RIGHT
CHANNEL
REGISTER
+5V
3506
2524
10K
3507
75
V
REF
GND
4
A
A
6
8
5V
5V
5V
A
5K6
F517
22n
3500
KILL
5K6
3501
B
C
1251
F510
1
F511
2
F512
3
F513
4
F514
5
F515
to/from ECO_SL
6
F516
7
EH-B
2523
10n
A
+10V
A
2500
STANDBY
7500
BC327-40
D
3535
BC558C
E
7501
D
10K
3503
100R
1507
3548
2K2
RT-01T1
A
3502
100R
3504
100R
+5V
STDBY
+10V
15K
47u
F521
F522
DIGITAL / OPTICAL OUT for CD723
2530
3537
220R
2521
220u
A
5
3,3V
6
3,3V
1n
2529
A
2510
220p
3512
3K3
VC
3
3,3V
3,3V
1n
-10V
A
3538
220R
8
2
4
-11,2V
2522
A
11,2V
7505-A
220u
VC
11,2V
7505-B
8
NJM4560D
Left
4
-11,2V
3511
3K3
2509
220p
KILL
1
2,1V
NJM4560D
Right
2,1V
3534
10K
2511
47u
5,4V
+5V
3527
47u
2512
2K2
BC557B
KILLP
-10V
35133514
+5V
47K
A
5,6V
7504
-8,3
6500
1N4148
3532
220K
47K
A
7
3539
1K
3543
1K
3540
1K
3545
1K
3541
1K
3544
1K
3542
1K
3547
1K
-8,3
-8,3
-8,3
-8,3
0V
7507
BC337-40
A
0V
7508
BC337-40
A
0V
7509
BC337-40
A
0V
7510
BC337-40
A
2513
2514
1506
F525
1
+10V
F526
-10V
F527
F528
A
F529
F530
A
F531
F532
Left
470p
A
Right
470p
A
2
3
4
5
EH-B
LINE OUT
YKC21-3418
3
1
2
1504
+10V
-10V
Left
AGND
Right
4
A
F
A
B
to headphone
C
D
E
F
1502
F540
3
F541
2
F542
1
to/from ECO_SL
PH-B
2541
1u
G
H
V
EVM
...DC voltages measured
in Play mode
5801
34
2
1
6
78
2542
100n
A
3556
10R
2543
100n
F543
F544
YKC21-3564
2
1
1252
F550
POWERED
1503
3
A
KILLI
STDBY
-VKK
F2
F1
D
+5V
F551
F552
F553
F554
F555
F556
F557
1
2
3
4
5
6
7
8
EH-B
G
to/from FRONT
H
1234567891011121314
7-4
AF Board Componentside view
7-4
98-05-29
3103 303 34026
E
B
C
This assembly drawing shows a summary of all possible versions.
For components used in a specific version
see schematic diagram respectively partslist.
This assembly drawing shows a summary
of all possible versions.
For components used in a specific version
see schematic diagram respectively partslist.