Manitowoc Ice E-0600 User Manual

E-0600 STACKING KIT

Installation Instructions

1. Installation of E-0600 Series Ice Machine and Storage Bin:
A. Open bin carton, lay carton on its side, and remove cardboard liner from inside bin. Place the liner on the floor in

front of the carton and slide the bin onto the liner. Attach four bin legs, set the bin upright, and check for damage.
Move bin to the set-up location and level. The legs are ad justable for leveling. If the legs are not used, use shim s
to level the bin. The NSF (National Sanitation Foundation) requires that a bin not on legs m ust be sealed to the
floor using mastic around the entire perimeter on the bottom of the bin.

B. See service manual for uncrating and inspection of both ice machines.
C. Remove the top cover from the lower ice machine.
D. Place the control bulb bracket on the back edge of bin, in the center (see FIG. 4).
E. Place cover from E-0600 kit on ice machine and replace screws. Set ice machine on the bin squarely.
F. Remove front panel, top cover, and end panel from second ice machine.

2. Thermostat Control Installation (see FIG. 2):
A. Remove thermostat control from E-0600 carton. Locate control on partition panel, under tim er box and toggle

switch. Mark two hole locations on panel using bracket holes as a guide. Drill two 1/8” holes and m ount control
to partition panel with two sheet metal screws.

B. Wiring Control (see FIG. 2 and FIG. 3).

a. Remove white plug located on partition panel (ice making compartment) underneath timer box and insert

7/8” bushing from kit. Insert two wire leads from thermostat control through partition panel into com pressor
compartment. Run leads up to and through smaller of the two bushings in partition panel and into timer box (see FIG.

2).

Remote and water m achines: See FIG. 2. Air m achines: See FIG. 3. Rem ove lead wire marked #16 from
toggle switch and connect to one lead from thermostat with double quick-connect from kit. Connect other
lead from thermostat to center quick-connect on toggle switch.

C. Place ice machine end panel and cover back on and set machine on top of first machine, carefully and squarely.
D. Remove the ice chutes and damper doors from upper and lower ice machines.
E. Remove the water curtain from the lower ice machine.
F. Pass the thermostat bulb through the ice chute opening in the upper machine (see FIG. 4).
G. Remove the screw on the bin switch housing and place a plas tic clamp on the thermostat tubing. Put the housing

screw through the clamp and replace screw and clamp to housing (see FIG. 4).

H. Remove the right-hand water curtain hanger screw and put a plastic clam p on the therm ostat tubing. Carefully

bend the tubing back to the evaporator position. Mount the clamp and curtain hanger back to original position.

I. Remove the right-hand harvest rack bracket screw and pl ace a plastic clam p on the therm ostat tubing. Put screw

through clamp and mount clamp to the harvest rack.

J. Feed the tubing through the right-hand corner of the ice chute opening. Carefully bend the tubing straight back to

the bin wall and then over to the plastic clam p on the br acket. Slide the bulb into the clam p on the bracket and
tighten the screws. Place a plastic clamp over the tubing a nd attach to the base of the machine with a sheet metal
screw.

K. Replace the lower ice m achine water curtain. Make sure the curtain can open and close freely without hitting on

the control tubing. If the curtain does hit the tubing, bend tubing enough to allow the curtain to pass.

3. Installation of Stacking Kit Ice Chutes (see FIG. 5 and 6):

A. Rem

ove the water pump from
studs. Rem ove electrical plug from socket. Lift the pump out of the water trough and disconnect the plastic
tubing. Reverse these steps for later installation.

B. Place ice chute “A” in lower ice chute opening in base.

Manitowoc Ice, Inc.

2110 South 26 Street, P.O. Box 1720, Manitowoc, WI 54221-1720 USA 8000893
Telephone [phone], Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879 Sheet 1 of 2

Web Site - www.manitowocice.com Rev. 06/06/01

C. Make sure the bin control tube has clearance between the base opening and ice chute.

the lower ice m achine. Take the water pum p and slide it up and off the mounting

D. Put the damper door, which was rem oved on an earlier step, in the ice chute. Rotate the dam per door. With the

door in the open position, the counterweight should trip th e micro-switch lever. When you hear the micro-switch
giving a clicking sound, y ou know the door is operating properly . If y ou don’t hear the switch clicking, loosen
the screws on the switch housing and move it closer to the counterweight.

E. To install the center ice chute “B”, the widest part of the chute is the top, and the flanged side should face the

front of the ice m achine. Insert the top of the center ice chute into the lower m achine ice compartment and slide
the top of the chute into the upper m achine ice chute opening from the bottom until it clears ice chute “A”. After
it clears the lower ice chute, let it sit on the chute and proceed to step F.

F. Place upper ice chute “C” into ice chute opening of the top ice machine base. Make sure the bin control bulb has

clearance between the base opening and ice chute.

G. Place damper door in ice chute. Make sure the damper door trips the micro-switch when opened. If not, return to

part 3, step D.

H. The center chute “B” fits over the outside of the upper chute. From inside the lower ice compartment, slide center

ice chute “B” onto the upper chute “C”. Fasten center chute to the upper chute with four sheet metal screws.

I. Take the bottom of the center chute and align the rivnuts on th e sides of the chute with the slots on the side of ice

chute “A”. The bottom of the center chute fits on the in side of the lower chute. Take a knurled m achine screw
and a lock washer and place in slot on lower chute. Tighten screw into rivnut.

J. Place center chute cover “D” on center chute and screw in place with ten sheet m etal screws. Drive six screws

through the cover into center chute, two screws into upper chute, two screws into lower chute.

K. Replace water pump in lower ice machine (see part 3, step A).

4. Bin Control Setting:

A. The top machine should shut off when the ice level in th e storage bin reaches the bulb. If the top machine shuts

off with the ice level in the bin above the control bul b, turn the black knob m arked colder counterclockwise
approximately 1/4 turn. If the ice level is below the bul b when the top ice m achine shuts off, turn the knob 1/4
turn clockwise.

B. Proceed to service manual for electrical and water hook-up and start-up procedure.

Parts List

Part Number

Description Quantity Required

6555414 Lower Ice Chute Assembly 1
6820824 Center Ice Chute Assembly 1
6555714 Upper Ice Chute Assembly 1
157481 Center Ice Chute Cover 1
5124641 #8 Sheet Metal Screws, Type B 20
5544591 #8 Shakeproof Lock Washers 20
5012041 Knurled Machine Screws 2
2350041 Ranco Bin Thermostat Control w/Bracket 1
302461 Bulb Bracket 1
5650031 Plastic Clamps 4
6026444 Top Cover Assy. 1

Sheet 2 of 2

Rev. 06/06/01

8000893