Makita UH200DWEX, UH200DW User Manual

ENGLISH (Original instructions)

INSTRUCTION MANUAL

Cordless Hedge Trimmer

UH200D

IMPORTANT: Read Before Using.

010965

1

ENGLISH (Original instructions)

r

SPECIFICATIONS

Model UH200D

Blade length 200 mm

Strokes per minute (min-1) 1,250

Overall length 460 mm

Net weight 1.2 kg

• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.

• Specifications and battery cartridge may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

Symbol

The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.

Intended use
The tool is intended for trimming hedges.

Noise
The typical A-weighted noise level determined according
to EN60745:

The noise level under working may exceed 80 dB (A).

･ Take particular care and attention.

･ Read instruction manual.

･ Do not expose to rain.

･ Danger; be aware of thrown objects.

･ Keep bystanders away.

･ Cutting means continues to run after the

Cd

･ Only for EU countries

Ni-MH
Li-ion

Sound pressure level (L
Uncertainty (K) : 2.5 dB(A)

Rated voltage D.C. 10.8 V

END011-3

Vibration

The vibration emission value determined according to
EN60745 :

Vibration emission (a
Uncertainty (K) : 1.5 m/s

The declared vibration emission value has been

•

measured in accordance with the standard test
method and may be used for comparing one tool
with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

motor is switched off.

Do not dispose of electric equipment or
battery pack together with household
waste material!
In observance of European Directive
2002/96/EC on waste electric and
electronic equipment, 2006/66/EC on
batteries and accumulators and waste
batteries and accumulators and their
implementation in accordance with
national laws, electric equipment and
battery pack that have reached the end
of their life must be collected separately
and returned to an environmentally
compatible recycling facility.

ENE014-1

ENG104-2

WARNING:

• The vibration emission during actual use of the

power tool can differ from the declared emission
value depending on the ways in which the tool is
used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).

For European countries only

EC Declaration of Conformity

We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):

Designation of Machine:

Cordless Hedge Trimme

Model No./ Type: UH200D
Specifications: see "SPECIFICATIONS" table.

are of series production and

) : 73.7 dB(A)

pA

Conforms to the following European Directives:

2000/14/EC, 2006/42/EC

Wear ear protection.

) : 2.5 m/s2 or less

h

2

ENG244-1

ENG901-1

ENH021-5

2

And are manufactured in accordance with the following
standards or standardised documents:

EN60745
The technical documentation is kept by our authorised
representative in Europe who is:

Makita International Europe Ltd,

Michigan, Drive, Tongwell,

Milton Keynes, MK15 8JD, England
The conformity assessment procedure required by
Directive 2000/14/EC was in Accordance with annex V.
Measured Sound Power Level: 81.8dB
Guaranteed Sound Power Level: 84dB

000230

27.8.2009

Tomoyasu Kato

Director

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, JAPAN

GEA006-2

General Power Tool Safety
Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or
serious injury.

Save all warnings and
instructions for future reference.

The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.

2. Do not operate power tools in explosive

atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.

Electrical safety

4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will

reduce risk of electric shock.

5. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.

7. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords

increase the risk of electric shock.

8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.

9. If operating a power tool in a damp location is

unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply. Use of an

GFCI reduces the risk of electric shock.

Personal safety

10. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while

operating power tools may result in serious
personal injury.

11. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.

12. Prevent unintentional starting. Ensure the

switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with

your finger on the switch or energising power tools
that have the switch on invites accidents.

13. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.

14. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.

15. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes,

jewellery or long hair can be caught in moving
parts.

16. If devices are provided for the connection of

dust extraction and collection facilities,
ensure these are connected and properly used.

Use of dust collection can reduce dust-related

3

hazards.

Power tool use and care

17. Do not force the power tool. Use the correct
power tool for your application. The correct

power tool will do the job better and safer at the
rate for which it was designed.

18. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.

19. Disconnect the plug from the power source

and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such

preventive safety measures reduce the risk of
starting the power tool accidentally.

20. Store idle power tools out of the reach of

children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are

dangerous in the hands of untrained users.

21. Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

22. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.

23. Use the power tool, accessories and tool bits

etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power

tool for operations different from those intended
could result in a hazardous situation.

Battery tool use and care

24. Recharge only with the charger specified by
the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of fire
when used with another battery pack.

25. Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and fire.

26. When battery pack is not in use, keep it away

from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. Shorting the battery

terminals together may cause burns or a fire.

27. Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may

cause irritation or burns.

Service

28. Have your power tool serviced by a qualified

repair person using only identical replacement
parts. This will ensure that the safety of the power

tool is maintained.

29. Follow instruction for lubricating and

changing accessories.

30. Keep handles dry, clean and free from oil and

grease.

GEB062-2

CORDLESS HEDGE TRIMMER
SAFETY WARNINGS

1. Hold the power tool by insulated gripping

surfaces only, because the cutter blade may
contact hidden wiring. Cutter blades contacting

a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an
electric shock.

2. Keep all parts of the body away from the cutter

blade. Do not remove cut material or hold
material to be cut when blades are moving.
Make sure the switch is off when clearing
jammed material. A moment of inattention while

operating the hedge trimmer may result in serious
personal injury.

3. Carry the hedge trimmer by the handle with

the cutter blade stopped. When transporting
or storing the hedge trimmer always fit the
cutting device cover. Proper handling of the

hedge trimmer will reduce possible personal injury
from the cutter blades.

4. Do not use the hedge trimmer in the rain or in wet
or very damp conditions. The electric motor is not
waterproof.

5. First-time users should have an experienced
hedge trimmer user show them how to use the
trimmer.

6. The hedge trimmer must not be used by children
or young persons under 18 years of age. Young
persons over 16 years of age may be exempted
from this restriction if they are undergoing training
under the supervision of an expert.

7. Use the hedge trimmer only if you are in good
physical condition. If you are tired, your attention
will be reduced. Be especially careful at the end of
a working day. Perform all work calmly and
carefully. The user is responsible for all damages
to third parties.

8. Never use the trimmer when under the influence of
alcohol, drugs or medication.

9. Check to make sure that the voltage and
frequency of the power supply correspond to the
specifications given on the identification plate. We

4

recommend the use of a residual-current-operated
circuit breaker (ground-fault circuit interrupter) with
a tripping current of 30 mA or less, or an earth
leakage current protector.

10. Work gloves of stout leather are part of the basic
equipment of the hedge trimmer and must always
be worn when working with it. Also wear sturdy
shoes with anti-skid soles.

11. Before starting work check to make sure that the
trimmer is in good and safe working order. Ensure
guards are fitted properly. The hedge trimmer
must not be used unless fully assembled.

12. Make sure you have a secure footing before
starting operation.

13. Hold the tool firmly when using the tool.

14. Do not operate the tool at no-load unnecessarily.

15. Immediately switch off the motor and remove the
battery cartridge if the cutter should come into
contact with a fence or other hard object. Check
the cutter for damage, and if damaged repair
immediately.

16. Before checking the cutter, taking care of faults, or
removing material caught in the cutter, always
switch off the trimmer and remove the battery
cartridge.

17. Switch off the trimmer and remove the battery
cartridge before doing any maintenance work.

18. When moving the hedge trimmer to another
location, including during work, always remove the
battery cartridge. Never carry or transport the
trimmer with the cutter running. Never grasp the
cutter with your hands.

19. Clean the hedge trimmer and especially the cutter
after use, and before putting the trimmer into
storage for extended periods. Lightly oil the cutter
and put on the cover. The cover supplied with the
unit can be hung on the wall, providing a safe and
practical way to store the hedge trimmer.

20. Store the hedge trimmer with the cover on, in a dry
room. Keep it out of reach of children. Never store
the trimmer outdoors.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.

CORDLESS GRASS SHEAR
SAFETY WARNINGS

WARNING! IMPORTANT READ CAREFULLY all

safety warnings and all instructions BEFORE USE .

Failure to follow the warnings and instructions may result
in electric shock, fire and/or serious injury.

Save all warnings and
instructions for future reference.

General instructions

1. To ensure correct operation, user has to read this
instruction manual to make himself familiar with
the handling of the equipment. Users insufficiently
informed will risk danger to themselves as well as
others due to improper handling.

2. Never allow people unfamiliar with these
instructions, people (including children) with
reduced physical, sensory or mental capabilities,
or lack of experience and knowledge to use the
equipment. Local regulations can restrict the age
of the operator.

3. Use the equipment with the utmost care and
attention.

4. Operate the equipment only if you are in good
physical condition. Perform all work calmly and
carefully. Use common sense and keep in mind
that the operator or user is responsible for
accidents or hazards occurring to other people or
their property.

5. Never operate the machine while people,
especially children, or pets are nearby.

6. Never use the equipment after consumption of
alcohol or drugs, or if feeling tired or ill.

7. The motor is to be switched off immediately in
case that the equipment shows any problem or
abnormal sign.

8. Switch off and remove the battery cartridge when
resting and when leaving the equipment
unattended, and place it in a safe location to
prevent danger to others or damage to the
equipment.

9. Don't force the equipment. it will do the job better
and with less likelihood of a risk of injury at the rate
for which it was designed.

10. Don't overreach. Keep proper footing and balance
at all times.

Personal protective equipment

1. Dress Properly. The clothing worn should be
functional and appropriate, i.e. it should be
tight-fitting but not cause hindrance. Do not wear
either jewelry or clothing which could become

5

GEB070-2

entangled. Wear protective hair covering to
contain long hair.

2. Wear eye protection and stout shoes at all times
while operating the machine.

Electrical and battery safety

1. Avoid dangerous environment. Don't use the
equipment in damp or wet locations or expose it to
rain. Water entering an equipment will increase
the risk of electric shock.

2. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one
type of battery pack may create a risk of fire when
used with another battery pack.

3. Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.

4. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
burns or a fire.

5. Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.

6. Do not dispose of the battery(ies) in a fire. The cell
may explode. Check with local codes for possible
special disposal instructions.

7. Do not open or mutilate the battery(ies). Released
electrolyte is corrosive and may cause damage to
the eyes or skin. It may be toxic if swallowed.

Starting up the equipment

1. Make sure that there are no children or other
people nearby, also pay attention to any animals in
the working vicinity. Otherwise stop using the
equipment.

2. Before use always check that the equipment is
safe for operation. Check the security of the
cutting tool and the guard and the switch
trigger/lever for easy and proper action. Check for
clean and dry handles and test the function of the
start/stop.

3. Check damaged parts before further use of the
equipment. A guard or other part that is damaged
should be carefully checked to determine that it
will operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other condition that may affect
its operation. A guard or other part that is damaged
should be properly repaired or replaced by our

authorized service center unless indicated
elsewhere in this manual.

4. Switch on the motor only when the hands and feet
are away from the cutting tool.

5. Before starting make sure that the cutting tool has
no contact with any objects.

Method of operation

1. Only use the equipment in good light and visibility.
During the winter season beware of slippery or wet
areas, ice and snow (risk of slipping). Always
ensure a safe footing.

2. Take care against injury to feet and hands from the
cutting tool.

3. Never stand on a ladder and run the equipment.

4. Never climb up into trees to perform cutting
operation with the equipment.

5. Never work on unstable surfaces.

6. Remove sand, stones, nails etc. found within the
working range. Foreign particles may damage the
cutting tool and can cause dangerous kick-backs.

7. Should the cutting tool hit stones or other hard
objects, immediately switch off the motor and
inspect the cutting tool.

8. Inspect the cutting tool at short regular intervals for
damage (detection of hairline cracks by means of
tapping-noise test).

9. Before commencing cutting, the cutting tool must
have reached full working speed.

10. The cutting tool has to be equipped with the
appropriate guard. Never run the equipment with
damaged guards or without guards in place!

11. All protective installations and guards supplied
with the equipment must be used during operation.

12. Always remove the battery cartridge from the
equipment:

− whenever leaving the equipment unattended;

− before clearing a blockage;

− before checking, cleaning or working on the

equipment;

− after striking a foreign object;

− whenever the equipment starts vibrating

abnormally.

13. Always ensure that the ventilation openings are
kept clear of debris.

Cutting Tools

1. Employ only the correct cutting tool for the job in
hand.

Maintenance instructions

1. The condition of the equipment, in particular of the
cutting tool of the protective devices must be
checked before commencing work.

2. Turn off the motor and remove the battery
cartridge before carrying out maintenance,

6