Makita T22lDW Instruction Manual
Cordless
Applicable staples
Stanler
Staple capacity Dimensions
(L x W x H)
Net weight
I
MODEL T221D
MODEL T22lDW
With
Fast
Charger
Battery Cartridge 9100
Voltage Charging time
1
Hr.
9.6
V
INSTRUCTION MANUAL
Model DC9700 Fast Charger
Input output
A.C. only
50
Hz
~
60
Hz
D.C.
7.2
V,
9.6
V
SPEC
IF
I
CAT
I 0 N
S
Model T221D
199
mm
x
58
mm
x
193
mm
(7-7/8” x 2-114” x 7-518”)
1.7
kg
(3.7
Ibs)
Staple
Nos.
*1019,
*lo22
1010, 1013, 1016,
I
100
~~~~
*
Manufacturer reserves the right to change specifications
without
notice.
*
Note:
1.
Specifications may differ from country
to
country.
2.
Staples
with
mark are for soft material only.
IMPORTANT
SAFETY INSTRUCTIONS
(For
All Tools)
WARNING:
WHEN USING ELECTRIC TOOLS, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS
BE
FOLLOWED TO REDUCE
THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL
INJURY, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
1.
2.
3.
4.
5.
6.
7.
8.
9.
IO.
11.
12.
13.
2
KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp
or wet locations. Keep work area well
lit.
Don't expose power tools to rain.
Don't use tool in presence of flammable liquids or gases.
KEEP CHILDREN AWAY.
All
visitors should be kept away from work area.
Don't let visitors contact tool or extension cord.
STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high
or locked-up place
-
out of reach of children.
DON'T FORCE TOOL.
It
will
do the job better and safer at the rate for which
it
was intended.
USE RIGHT TOOL. Don't force small tool or attachment to do the job of a
heavy-duty tool. Don't use tool for purpose not intended.
DRESS PROPERLY. Don't wear loose clothing or jewelry. They can be caught
in moving parts. Rubber gloves and non-skid footwear are recommended
when working outdoors. Wear protective hair covering to contain long hair.
USE SAFETY GLASSES. Also use face or dust mask if cutting operation is
dusty.
DON'T ABUSE CORD. Never carry tool by cord or yank
it
to disconnect from
receptacle. Keep cord from heat, oil, and sharp edges.
SECURE WORK. Use clamps or a vise to hold work. It's safer than using
your hand and
it
frees both hands to operate
tool.
DON'T OVERREACH. Keep proper footing and balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and
safer performance. Follow instructions for lubricating and changing acces-
sories. Inspect tool cords periodically and if damaged, have repaired by autho-
rized service facility. Inspect extension cords periodically and replace if
damaged. Keep handles dry, clean, and free from oil and grease.
DISCONNECT TOOLS. When not in use, before servicing, and when chang-
ing accessories, such as blades, bits, cutters.
14.
REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are removed from tool before turning
it
on.
15.
AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger
on switch. Be sure switch is
OFF
when plugging in.
16.
OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only
extension cords intended for use outdoors and
so
marked.
17.
STAY ALERT. Watch what you are doing, use common sense. Don't operate
tool when you are tired.
18.
CHECK DAMAGED PARTS. Before further use of the tool, a guard or other
part that is damaged should be carefully checked to determine that
it
will
operate properly and perform its intended function. Check for alignment of
moving parts, binding
of
moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation. A guard or other part
that is damaged should be properly repaired or replaced by an authorized
service center unless otherwise indicated elsewhere in this instruction
manual. Have defective switches replaced by authorized service center. Don't
use tool
if
switch does not turn
it
on
and off.
19.
GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded
surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.
20.
REPLACEMENT PARTS. When servicing, use only identical replacement parts.
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle,
outlet, etc.) be sure the voltage supplied is the same
as
that specified on the
nameplate of the tool. A power source with voltage greater than that specified
for the tool can result
in
SERIOUS INJURY
to
the user
-
as well as damage to
the tool. If in doubt, DO NOT PLUG IN THE
TOOL.
Using a power source with
voltage less than the nameplate rating is harmful to the motor.
3
I
M
PO
RTANT
Length of Cord (Feet)
AWG Size of Cord
SAFETY
25
50
100 150
18 18 18 16
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
SAVE
THESE
INSTRUCTIONS
-
This manual
contains important safety and operating instructions for battery charger.
Before using battery charger, read all instructions and cautionary markings
on
(11
battery charger,
(2)
battery, and
(3)
product using battery.
CAUTION
-
To reduce risk of injury, charge only MAKITA Battery
7000,
9000
or
9100.
Other types of batteries may burst causing personal injury
and damage.
Do not expose charger to rain or snow.
Use of an attachment not recommended or sold by the battery charger
manufacturer may result
in
a risk of fire, electric shock, or injury to persons.
To reduce risk
of
damage to electric plug and cord, pull by plug rather than
cord when disconnecting charger.
Make sure cord is located
so
that
it
will not be stepped on, tripped over,
or otherwise subjected to damage or stress.
An extension cord should not be used unless absolutely necessary. Use of
improper extension cord could result in a risk of fire and electric shock.
If
extension cord must be used, make sure:
a. That pins on plug of extension cord are the same number, size, and shape
b. That extension cord is properly wired and in good electrical condition; and
c. That wire size is at least as large as the one specified in the table below.
TABLE
1
RECOMMENDED MINIMUM AWG SIZE FOR
EXTENSION CORDS
FOR
BATTERY CHARGERS
as those of plug on charger;
Do not operate charger with damaged cord or plug
-
replace them im-
mediately.
Do not operate charger if
it
has received a sharp blow, been dropped, or
otherwise damaged in any way; take
it
to a qualified serviceman.
Do not disassemble charger or battery cartridge; take
it
to a qualified
serviceman when service
or
repair is required. Incorrect reassembly may
result
in
a risk of electric shock or fire.
To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk.
4
ADDITIONAL SAFETY RULES
FOR CHARGER
&
BATTERY CARTRIDGE
1.
Do
not charge Battery Cartridge when temperature
is
BELOW 10°C
(5OOF)
2.
Do
not attempt to use a step-up transformer, an engine generator or
DC
power
3.
Do
not allow anything to cover or clog the charger vents.
4.
Always cover the battery terminals
with
the battery cover when the battery
5.
Do
not short the battery cartridge:
or
ABOVE 4OoC (104OF).
receptacle.
cartridge
is
not used.
(1)
Do
not touch the terminals
with
any conductive material.
(2)
Avoid storing battery cartridge
in
a container
with
other metal objects such
(3)
Do
not expose battery cartridge to water or rain.
as nails, coins, etc.
A battery short can cause a large current flow, overheating, possible burns
and even a breakdown.
6.
Do
not store the tool and Battery Cartridge
in
locations where the tempera-
7.
Do
not incinerate the Battery Cartridge even if
it
is severely damaged or is
ture may reach or exceed
5OoC
(122OF).
completely worn out. The battery cartridge can explode
in
a fire.
5
Loading...