Makita HW120 Instruction Manual
INSTRUCTION MANUAL
Hot power
washer
HW120
WARNING: For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FURTHER REFERENCE
ENGLISH
HW120 Manual.qxd:Layout 1 21/7/08 10:23 Page 1
Contents
1. Technical data
2. General outline
3. Machine identification
4. Main parts
5. Safety instructions
6. Machine installation
7. Machine start up
8. Standard equipment
9. Options
10. Detergents
11. Single phase electrical diagram
12. Labels
13. Maintenance
14. Inner coil cleaning
15. EC Declaration of conformity
16. Causes and solutions
17. WEEE statement
HW120 Manual.qxd:Layout 1 21/7/08 10:23 Page 2
1. Technical data
MACHINE SPECIFICATION
Working Pressure 110 bar
Max Pressure 120 bar
Flow rate 510 l/hr
Max temperature 90ºC
Motor type Induction
Pump Triplex/ceramic coated pistons
Fuel type Diesel
Fuel tank capacity 8 Litres
Input wattage 2.2 kw
Volt age/Frequecy 230V/50 Hz
Motor insulation F class
Motor protection IPX5
Repulsive force of the gun to the max pressure 9.9 N
Unit vibrations 2.64 M/s2
Max water input pressure 12 bar
Net weight 78.7 kg
MACHINE DIMENSIONS
540mm
800mm
750mm
HW120 Manual.qxd:Layout 1 21/7/08 10:23 Page 3
2. General outline
3. Machine identification
The machine is exclusively meant for washing and cleaning with hot or
cold water surfaces apt to being treated with mechanical high pressure jet
system and subject to eventual chemical action of detergents. Before
using the cleaner, make sure that the identification plate is fixed on the
machine; if the plate is missing, please don’t use the machine and contact
immediately your dealer. Don’t leave the machine unattended in your work
environment. After the daily use, it is recommended to keep the cleaner in
a dry place protected from bad weather conditions.
HW120 Manual.qxd:Layout 1 21/7/08 10:23 Page 4
4. Main parts
1. Lance
2. High pressure hose
3. Feeding cable
4. Detergent suction
5. Detergent filter
6. Fuel tank
7. By-pass valve
8. High pressure pump
9. Electrical motor
10. Fuel pump
11. Burner motor
12. Boiler
13. Combustion head
14. Pressure switch
15. Electrical panel
16. ON/OFF switch
17. Thermostat
18. Pressure gauge
HW120 Manual.qxd:Layout 1 21/7/08 10:23 Page 5
5. Safety instructions
Make sure that the machine is constantly supplied with water.
Dry working would cause serious damages to the cleaner seal system.
• Electrical connections must be carried out by skilled/trained
personnel only.
• Never pull the power cord to disconnect the plug nor pull the hose
to move the machine.
• Don’t leave the machine in low temperature and protect it from frost
and general bad weather conditions.
• Avoid vehicles transit on the high pressure hose.
• While the machine is running do not cover it and avoid placing it where
there’s low air supply.
• If you are working indoors, it’s compulsory to install a fan to discharge
the exhaust gases outside.
• The fan terminal must not be obstructed. Don’t leave the lance or any
other object near the exhaust outlet.
• The nature of the gases as well as the high temperature are to be
considered very dangerous, the operator must thus be adequately
informed in order to avoid being scalded.
• Don’t leave the machine outside when it rains or when the weather
conditions are bad.
• The operators must wear protection clothes while using the machine.
• Don’t use the machine under the rain or in case of storms.
• Do not leave the machine for more than 5 minutes working with the gun
closed, the water temperature would increase rapidly causing serious
damages to the seal system.
• Each time the cleaner has to be switched off blow off the hose residual
pressure by using the gun.
• Do not use fuels different from the ones suggested by the manufacturer.
HW120 Manual.qxd:Layout 1 21/7/08 10:23 Page 6
Loading...