Makita HMl500B User guide
Demolition Hammer
MODEL
INSTRUCTION MANUAL
HMl500B
SPECIFICATIONS
Blows per minute
1,300
~
Overall length Net weight
807
mm
(31-3/4")
kg (42 Ibs)
19
IMPORTANT
SAFETY
WARNING:
WHEN USING ELECTRIC TOOLS, BASIC SAFETY
INSTRUCTIONS
(For
All
Tools)
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE
THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL
INJURY, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
1.
KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
2.
CONSIDER WORK AREA ENVIRONMENT. Don't use power tools
or wet locations. Keep work area well
Don't use tool
KEEP CHILDREN AWAY.
3.
Don't let visitors contact tool or extension cord.
4.
STORE IDLE TOOLS. When not
or locked-up place
DON'T FORCE TOOL.
5.
it
was intended.
USE RIGHT TOOL. Don't force small tool or attachment to do the job of a
6.
heavy-duty tool. Don't use tool for purpose not intended.
7.
DRESS PROPERLY. Don't wear loose clothing or jewelry. They can be caught
in moving parts. Rubber gloves and non-skid footwear are recommended
when working outdoors. Wear protective hair covering to contain long hair.
8.
USE SAFETY GLASSES. Also use face or dust mask
dusty.
DON'T ABUSE CORD. Never carry tool by cord or yank
9.
receptacle. Keep cord from heat, oil, and sharp edges.
SECURE WORK. Use clamps or a vise to hold work. It's safer than using
IO.
your hand and
DON'T OVERREACH. Keep proper footing and balance at all times.
11.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and
12.
safer performance. Follow instructions for lubricating and changing accesÂsories. Inspect tool cords periodically and
rized service facility. Inspect extension cords periodically and replace if
damaged. Keep handles dry, clean, and free from oil and grease.
DISCONNECT TOOLS. When not in use, before servicing, and when chang-
13.
ing accessories, such as blades, bits, cutters.
in
presence of flammable liquids or gases.
All
visitors should be kept away from work area.
in
-
out of reach of children.
It
will do the job better and safer at the rate for which
it
frees both hands to operate tool.
lit.
Don't expose power tools to rain.
use, tools should be stored in dry, and high
if
cutting operation is
it
to disconnect from
if
damaged, have repaired by autho-
in
damp
2
14.
REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are removed from
it
on.
15.
AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger
on switch. Be sure switch is OFF when plugging
16.
OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only
extension cords intended for use outdoors and
17.
STAY ALERT. Watch what you are doing, use common sense. Don't operate
tool when you are tired.
18.
CHECK DAMAGED PARTS. Before further use of the tool, a guard or other
part that
operate properly and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation. A guard or other part
that is damaged should be properly repaired or replaced by an authorized
service center unless otherwise indicated elsewhere in this instruction
manual. Have defective switches replaced by authorized service center. Don't
use tool if switch does not turn
19.
GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded
surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.
20.
REPLACEMENT PARTS. When servicing, use only identical replacement parts.
21.
POLARIZED PLUGS. To reduce the risk of electric shock, this equipment has
a polarized plug (one blade is wider than the other). This plug will fit
polarized outlet only one way. If the plug does not
reverse the plug. If
the proper outlet.
is
damaged should be carefully checked to determine that
it
on and off.
it
still does not
Do
not change the plug in any way.
fit,
contact a qualified electrician to install
so
tool
before turning
in.
marked.
fit
fully in the outlet,
it
will
in
a
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle,
outlet, etc.) be sure the voltage supplied is the same as that specified on the
nameplate of the tool. A power source with voltage greater than that specified
for the tool can result in SERIOUS INJURY to the user
If
the tool.
voltage less than the nameplate rating is harmful to the motor.
in doubt,
DO
NOT PLUG IN THE TOOL. Using a power source with
-
as well as damage to
3
ADDITIONAL SAFETY RULES
1.
Wear a hard hat (safety helmet), safety glasses and/or face shield.
highly recommended that you wear a dust mask, ear protectors and thickly
padded gloves.
2.
Be sure the bit is secured
3.
Under normal operation, the tool is designed to produce vibration. The screws
can come loose easily, causing a breakdown or accident. Check tightness
of screws carefully before operation.
4.
In
cold weather or when the tool has not been used for a long time, let the
tool warm up for a while by operating
the lubrication. Without proper warm-up, hammering operation is difficult.
5.
Always be sure you have a firm footing.
Be sure no one is below when using the tool in high locations.
6.
Hold the tool firmly with both hands.
7.
Keep hands away from moving parts.
8.
Do
not leave the tool running. Operate the tool only when hand-held.
9.
Do
not point the tool at any one
fly out and injure someone seriously.
IO.
When chipping into walls, floors or wherever "live" electrical wires may be
DO
encountered,
Hold the tool by the insulated grasping surfaces to prevent electric shock
if you chip into a "live" wire.
11.
Do
not touch the bit or parts close to the bit immediately after operation;
they may be extremely hot and could burn your skin.
NOT TOUCH ANY METAL PARTS
in
place before operation.
it
under no load. This
in
the area when operating. The bit could
OF
THE TOOL!
will
loosen up
It
is also
SAVE THESE INSTRUCTIONS.
4
Loading...