Makita HM1317C, HM1317CB, HM1307CB, HM1307C User Manual

ENGLISH (Original instructions)

INSTRUCTION MANUAL

Electric Breaker

HM1317C HM1307C HM1317CB HM1307CB

DOUBLE INSULATION

WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

010282

ENGLISH (Original instructions)

SPECIFICATIONS

Model HM1317C HM1307C HM1317CB HM1307CB

Blows per minute 730 - 1,450

Overall length 715 mm 824 mm

Net weight 17.0 kg 15.3 kg 19.0 kg 17.3 kg

• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.

• Note: Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

Symbols

The following show the symbols used for the equipment. Be sure that you understand their meaning before use.

･ Read instruction manual.

･ DOUBLE INSULATION

･ Only for EU countries

Intended use The tool is intended for chiselling work in concrete, brick, stone and asphalt as well as for driving and compacting with appropriate accessories.

Power supply The tool should be connected only to a power supply of the same voltage as indicated on the nameplate, and can only be operated on single-phase AC supply. They are double-insulated in accordance with European Standard and can, therefore, also be used from sockets without earth wire.

For Model HM1307C

For European countries only Noise

The typical A-weighted noise level determined according to EN60745:

Sound pressure level (L Sound power level (L

Safety class /II

END201-4

Uncertainty (K) : 3 dB(A)

Vibration

The vibration total value (tri-axial vector sum) determined according to EN60745:

Work mode : chiseling function with side handle Vibration emission (a Uncertainty (K) : 2.0 m/s

Do not dispose of electric equipment together with household waste material! In observance of European Directive 2002/96/EC on waste electric and electronic equipment and its implementation in accordance with national law, electric equipment that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.

ENE045-1

For Model HM1307CB

For European countries only Noise

The typical A-weighted noise level determined according to EN60745:

Sound pressure level (L Sound power level (L Uncertainty (K) : 3 dB(A)

Vibration

The vibration total value (tri-axial vector sum) determined according to EN60745:

ENF002-1

Work mode : chiseling function with side handle Vibration emission (a Uncertainty (K) : 1.5 m/s

For Model HM1317C

For European countries only Noise

The typical A-weighted noise level determined according to EN60745:

ENG102-2

Sound pressure level (L Sound power level (L Uncertainty (K) : 3 dB(A)

) : 81 dB(A)

) : 101 dB(A)

Wear ear protection

) : 12.5 m/s

h,CHeq

) : 81 dB(A)

) : 101 dB(A)

Wear ear protection

) : 12.0 m/s

h,CHeq

) : 81 dB(A)

) : 101 dB(A)

Wear ear protection

ENG216-2

ENG102-2

ENG216-2

ENG102-2

Vibration

ENG216-2

The vibration total value (tri-axial vector sum) determined according to EN60745:

Work mode : chiseling function with side handle Vibration emission (a Uncertainty (K) : 1.5 m/s

h,CHeq

) : 8.5 m/s

For Model HM1317CB

ENG102-2

For European countries only Noise

The typical A-weighted noise level determined according to EN60745:

Sound pressure level (L Sound power level (L Uncertainty (K) : 3 dB(A)

Wear ear protection

) : 81 dB(A)

) : 101 dB(A)

ENG216-2

Vibration

The vibration total value (tri-axial vector sum) determined according to EN60745:

Work mode : chiseling function with side handle Vibration emission (a Uncertainty (K) : 1.5 m/s

The declared vibration emission value has been

•

h,CHeq

) : 7.0 m/s

ENG901-1

measured in accordance with the standard test method and may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the

power tool can differ from the declared emission value depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).

ENH213-1

EC Declaration of Conformity

We Makita Corporation as the responsible manufacturer declare that the following Makita machine(s):

Designation of Machine:

Electric Breake

Model No./ Type: HM1307C,HM1307CB,HM1317C,HM1317CB are of series production and

Conforms to the following European Directives:

2000/14/EC, 98/37/EC until 28th December 2009 and then with 2006/42/EC from 29th December

2009 And are manufactured in accordance with the following standards or standardised documents:

EN60745 The technical documentation is kept by our authorised representative in Europe who is:

Makita International Europe Ltd,

Michigan, Drive, Tongwell,

Milton Keynes, MK15 8JD, England The conformity assessment procedure required by Directive 2000/14/EC was in Accordance with annex VIII. Notified Body:

TUV Rheinland Product Safety GmbH,

identification no. 0197 Model HM1307C

Measured Sound Power Level: 101dB

Guaranteed Sound Power Level: 103dB

Model HM1307CB

Measured Sound Power Level: 101dB

Guaranteed Sound Power Level: 104dB

Model HM1317C

Measured Sound Power Level: 101dB

Guaranteed Sound Power Level: 103dB

Model HM1317CB

Measured Sound Power Level: 101dB

Guaranteed Sound Power Level: 104dB

000230

8th April 2009

Tomoyasu Kato

Director

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, JAPAN

GEA005-3

General Power Tool Safety Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or dark areas invite accidents.

2. Do not operate power tools in explosive

atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

3. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

4. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will

reduce risk of electric shock.

5. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

6. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

7. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords

increase the risk of electric shock.

8. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

9. If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

10. Use of power supply via a RCD with a rated

residual current of 30mA or less is always recommended.

Personal safety

11. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

12. Use personal protective equipment. Always wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

13. Prevent unintentional starting. Ensure the

switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools

with your finger on the switch or energising power tools that have the switch on invites accidents.

14. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

15. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

16. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing, and gloves away from moving parts. Loose clothes,

jewellery or long hair can be caught in moving parts.

17. If devices are provided for the connection of

dust extraction and collection facilities, ensure these are connected and properly used.

Use of dust collection can reduce dust-related hazards.

Power tool use and care

18. Do not force the power tool. Use the correct power tool for your application. The correct

power tool will do the job better and safer at the rate for which it was designed.

19. Do not use the power tool if the switch does

not turn it on and off.

be controlled with the switch is dangerous and must be repaired.

20. Disconnect the plug from the power source

and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting the power tool accidentally.

21. Store idle power tools out of the reach of

children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

22. Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

23. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

Any power tool that cannot

+ 8 hidden pages