Makita EBH252L, EBH253U, EBH252U, EBH253L User Manual

EBH252U/EBH253U/EBH252L/EBH253L

GB Petrol Brushcutter

F Débroussailleuse thermique

LS Desbrozadora

INSTRUCTION MANUAL MANUEL D'INSTRUCTIONS MANUAL DE INSTRUCCIONES

EBH252U EBH253U

Important:

Read this instruction manual carefully before putting the Petrol Brushcutter into operation and strictly observe the safety regulations! Preserve instruction manual carefully!

Important :

Lisez attentivement ce manuel d'instructions avant d'utiliser la débroussailleuse thermique et respectez scrupuleusement les règlements de sécurité! Conservez précieusement ce manuel d'instructions!

Importante:

Lea esta manual de instrucciones con atención antes de utilizar la desbrozadora y ¡observe estrictamente las regulaciones de seguridad! ¡Conserve cuidadosamente su manual de instrucciones!

EBH252L EBH253L

English

Thank you very much for purchasing the MAKITA Petrol Brushcutter. We are pleased to recommend to you the MAKITA Petrol Brushcutter which is the result of a long development programme and many years of knowledge and experience. Please read this booklet which refers in detail to the various points that will demonstrate its outstanding performance. This will assist you to obtain the best possible result from your MAKITA Petrol Brushcutter.

SYMBOLS

You will note the following symbols when reading the instructions manual.

Read instruction manual and follow the warnings and safety precautions!

Table of Contents Page

Symbols .........................................................................2

Safety instructions .........................................................3

Technical data................................................................7

Designation of parts.......................................................9

Mounting of handle ......................................................10

Mounting of protector...................................................11

Mounting of cutter blade or nylon cutting head............12

Before start of operation ..............................................13

Correct handling of machine........................................15

Points in operation and how to stop ............................15

Resharpening the cutting tool ......................................17

Servicing instructions...................................................19

Storage ........................................................................22

Wear protective helmet, eye and ear protection!

Take Particular care and attention!

Forbidden!

Keep distance!

Flying object hazard!

No smoking!

No open ame!

Protective gloves must be worn!

Top permissible tool speed

Fuel (Gasoline)

Engine-manual start

Emergency stop

First Aid

Recycling

ON/START

OFF/STOP

Wear sturdy boots with nonslip soles. Steeltoed safety boots are recommended!

Kickback!

Keep the area of operation clear of all persons and pets!

SAFETY INSTRUCTIONS

General Instructions

– To ensure correct operation, user has to read this instruction manual to make

himself familiar with the handling of the Petrol Brushcutter. Users insufciently

informed will risk danger to themselves as well as others due to improper handling.

– It is recommended only to lend the Petrol Brushcutter to people who have

proven to be experienced with Petrol Brushcutters. Always hand over the instruction manual.

– First users should ask the dealer for basic instructions to familiarize oneself

with the handling of an engine powered cutter.

– Children and young persons aged under 18 years must not be allowed

to operate the Petrol Brushcutter. Persons over the age of 16 years may however use the device for the purpose of being trained only whilst under

supervision of a qualied trainer.

– Use Petrol Brushcutters with the utmost care and attention. – Operate the Petrol Brushcutter only if you are in good physical condition.

Perform all work calmly and carefully. The user has to accept liability for others.

– Never use the Petrol Brushcutter after consumption of alcohol or drugs, or if

feeling tired or ill.

Intended use of the machine

– The Petrol Brushcutter is only intended for cutter grass, weeds, Bushes,

undergrowth it should not be used for any other purpose such as Edging or hedge cutting as this may cause injury.

Personal protective equipment

– The clothing worn should be functional and appropriate, i.e. it should be tight-

tting but not cause hindrance. Do not wear either jewelry or clothing which

could become entangled with bushes or shrubs.

– In order to avoid either head-, eye-, hand-or foot injuries as well as to protect

your hearing the following protective equipment and protective clothing must be used during operation of the Petrol Brushcutter.

– Always wear a helmet where there is a risk of falling objects. The protective

helmet (1) is to be checked at regular intervals for damage and is to be replaced at the latest after 5 years. Use only approved protective helmets.

– The visor (2) of the helmet (or alternatively goggles) protects the face from

ying debris and stones. During operation of the Petrol Brushcutter always

wear goggles, or a visor to prevent eye injuries.

– Wear adequate noise protection equipment to avoid hearing impairment (ear

muffs (3), ear plugs etc.).

– The work overalls (4) protect against ying stones and debris.

We strongly recommend that the user wears work overalls.

– Special gloves (5) made of thick leather are part of the prescribed equipment

and must always be worn during operation of the Petrol Brushcutter.

– When using the Petrol Brushcutter, always wear sturdy shoes (6) with a non-

slip sole. This protects against injuries and ensures a good footing.

Starting up the Petrol Brushcutter

– Please make sure that there are no children or other people within a working

range of 15 meters (50 ft), also pay attention to any animals in the working vicinity.

– Before use always check that the Petrol Brushcutter is safe for operation:

Check the security of the cutting tool, the control lever for easy action and check for proper functioning of the control lever lock.

– Rotation of the cutting tool during idling speed is not allowed. Check with your

dealer for adjustment if in doubt. Check for clean and dry handles and test the function of the start/stop switch.

Diagrammatic gure

15 Meters

Start the Petrol Brushcutter only in accordance with the instructions. – Do not use any other methods for starting the engine!

– Use the Petrol Brushcutter and the tools only for such applications as

specied.

– Only start the Petrol Brushcutter engine, after the entire assembly is done.

Operation of the device is only permitted after all the appropriate accessories are attached!

– Before starting make sure that the cutting tool has no contact with hard

objects such as branches, stones etc. as the cutting tool will revolve when

starting. – The engine is to be switched off immediately in case of any engine problems. – Should the cutting tool hit stones or other hard objects, immediately switch off

the engine and inspect the cutting tool. – Inspect the cutting tool at short regular intervals for damage (detection of

hairline cracks by means of tapping-noise test). – Operate the Petrol Brushcutter only with the shoulder strap attached which is

to be suitably adjusted before putting the Petrol Brushcutter into operation. It

is essential to adjust the shoulder strap according to the user size to prevent

fatigue occurring during use. Never hold the cutter with one hand during use. – During operation always hold the Petrol Brushcutter with both hands.

Always ensure a safe footing. – Operate the Petrol Brushcutter in such a manner as to avoid inhalation of

the exhaust gases. Never run the engine in enclosed rooms (risk of gas

poisoning). Carbon monoxide is an odorless gas. – Switch off the engine when resting and when leaving the Petrol Brushcutter

unattended, and place it in a safe location to prevent danger to others or

damage to the machine. – Never put the hot Petrol Brushcutter onto dry grass or onto any combustible

materials. – The cutting tool has to be equipped with it appropriate guard.

Never run the cutter without this guard! – All protective installations and guards supplied with the machine must be

used during operation.

– Never operate the engine with faulty exhaust mufer.

– Shut off the engine during transport. – During transport over long distances the tool protection included with the

equipment must always be used. – Ensure safe position of the Petrol Brushcutter during car transportation to

avoid fuel leakage. – When transporting the Petrol Brushcutter, ensure that the fuel tank is

completely empty. –

When unloading the Petrol Brushcutter from the truck, never drop the Engine

to the ground or this may severely damage the fuel tank. –

Except in case of emergency, never drop or cast the Petrol Brushcutter to the

ground or this may severely damage the Petrol Brushcutter. – Remember to lift the entire equipment from the ground when moving the

equipment. Dragging the fuel tank is highly dangerous and will cause damage

and leakage of fuel, possibly causing re.

• Resting

• Transport

• Refuelling

• Maintenance

• Tool replacement

Refuelling

– Shut off the engine during refuelling, keep away from open ames and do not

smoke. – Avoid skin contact with mineral oil products. Do not inhale fuel vapor. Always

wear protective gloves during refuelling. Change and clean protective clothing

at regular intervals. – Take care not to spill either fuel or oil in order to prevent soil contamination

(environmental protection). Clean the Petrol Brushcutter immediately after

fuel has been spilt. – Avoid any fuel contact with your clothing. Change your clothing instantly if

fuel has been spilt on it (to prevent clothing catching re).

– Inspect the fuel cap at regular intervals making sure that it can be securely

fastened and does not leak. – Carefully tighten the fuel tank cap. Change location to start the engine (at

least 3 meters away from the place of refuelling). – Never refuel in closed rooms. Fuel vapors accumulate at ground lever (risk of

explosions). – Only transport and store fuel in approved containers. Make sure the fuel

stored is not accessible to children.

3 meters

Method of operation

– Only use the Petrol Brushcutter in good light and visibility. During the winter

season beware of slippery or wet areas, ice and snow (risk of slipping).

Always ensure a safe footing. – Never cut above waist height. – Never stand on a ladder and run the Petrol Brushcutter. – Never climb up into trees to perform cutting operation with the Petrol

Brushcutter. – Never work on unstable surfaces. – Remove sand, stones, nails etc. found within the working range.

Foreign particles may damage the cutting tool and can cause dangerous

kick-backs. – Before commencing cutting, the cutting tool must have reached full working

speed.

Kickback

– When operating the Petrol Brushcutter, uncontrolled kickback may occur. – This is particularly the case when attempting to cut within a blade segment

between 12 and 2 o’clock. – Never apply the Petrol Brushcutter within a segment between 12 and 2

o’clock. – Never apply this segment of the Petrol Brushcutter blade to solids, such as

bushes and trees, etc., having a diameter in excess of 3 cm or the Petrol

Brushcutter will be deected at great force with the risk of injuries.

Kickback prevention

To avoid kickbacks, observe the following:

– Operation within a blade segment between 12 and 2 o’clock presents positive

hazards, especially when using metal cutting tools. – Cutting operations within a blade segment between 11 and 12 o’clock, and

between 2 and 5 o’clock, must only be performed by trained and experienced

operators, and then only at their own risk.

Easy cutting with almost no kickback is possible within a blade segment

between 8 and 11 o’clock.

Cutting Tools

Employ only the correct cutting tool for the job in hand.

Caution: Kickback

Diagrammatic

gure

Diagrammatic

gure

EBH252U, EBH253U, EBH252L, EBH253L with cutter blade, Nylon cutting head For cutting thick materials, such as weed, high grass, bushes, shrubs, underwood, thicket etc. (max. 2 cm dia. thickness). Perform this cutting work by swinging the Petrol Brushcutter evenly in half-circles from right to left (similar to using a scythe).

Maintenance instructions

– The condition of the cutter, in particular of the cutting tool of the protective

devices and also of the shoulder strap must be checked before commencing

work. Particular attention is to be paid to the cutting blades which must be

correctly sharpened. – Turn off the engine and remove spark plug connector when replacing or

sharpening cutting tools, and also when cleaning the cutter or cutting tool.

Never straighten or weld damaged cutting tools.

– Operate the Petrol Brushcutter with as little noise and contamination as

possible. In particular check the correct setting of the carburetor. – Clean the Petrol Brushcutter at regular intervals and check that all screws

and nuts are well tightened.

– Never service or store the Petrol Brushcutter in the vicinity of naked ames.

– Always store the Petrol Brushcutter in locked rooms and with an emptied fuel

tank.

Observe the relevant accident prevention instructions issued by the relevant trade associations and by the insurance companies.

Do not perform any modications on the Petrol Brushcutter as this will endanger your safety.

The performance of maintenance or repair work by the user is limited to those activities as described in the instruction manual. All other work is to be done by an Authorized Service Agent. Use only genuine spare parts and accessories released and supplied by MAKITA. Use of non-approved accessories and tools means increased risk of accidents.

MAKITA will not accept any liability for accidents or damage caused by the use of non-approved cutting tools and xing devices of cutting tools,

or accessories.

First Aid

In case of accident make sure that a rst-aid box is available in the vicinity of the cutting operations. Immediately replace any item taken from the rst aid box.

When asking for help, please give the following information:

– Place of accident – What happened – Number of injured persons – Kind of injuries – Your name

Packaging

The MAKITA Petrol Brushcutter will be delivered in two protective cardboard boxes to prevent transport damage. Cardboard is a basic raw material and is therefore consequently reusable or suitable for recycling (waste paper recycling).

TECHNICAL DATA EBH252U, EBH252L

Model

EBH252U EBH252L

Bike handle Loop handle

Dimensions: length x width x height (without cutting blade) mm

Mass (without plastic guard and cutting blade) kg

Volume (fuel tank) L

1,770 x 620 x 490 1,770 x 330 x 265

5.7 5.2

0.5

Volume (oil tank) L 0.08

Engine displacement cm

24.5

Maximum engine performance kw 0.71 at 7,000 min

Engine speed at recommended max. spindle speed min

Maximum spindle speed (corresponding) min

Maximum fuel consumption kg/h

Maximum specic fuel consumption g/kwh

Idling speed min

Clutch engagement speed min

Carburetor type

-1

8,500

6,500

0.33

408

-1

3,000

3,750

WALBRO WYL

Ignition system type Solid state ignition

Spark plug type

NGK CMR4A

Electrode gap mm 0.7 - 0.8

Fuel Automobile gasoline

Engine Oil

SAE 10W-30 oil of API Ciassication,

Class SF or higher (4-stroke engine for automobile)

Cutting tools (cutter blade dia.) mm 230

Gear ratio 14/19

-1

TECHNICAL DATA EBH253U, EBH253L

Model

EBH253U EBH253L

Bike handle Loop handle

Dimensions: length x width x height (without cutting blade) mm

Mass (without plastic guard and cutting blade) kg

Volume (fuel tank) L

1,770 x 620 x 490 1,770 x 330 x 265

5.9 5.3

0.5

Volume (oil tank) L 0.08

Engine displacement cm

24.5

Maximum engine performance kw 0.71 at 7,000 min

Engine speed at recommended max. spindle speed min

Maximum spindle speed (corresponding) min

Maximum fuel consumption kg/h

Maximum specic fuel consumption g/kwh

Idling speed min

Clutch engagement speed min

Carburetor type

-1

8,500

6,500

0.33

408

-1

3,000

3,750

WALBRO WYL

Ignition system type Solid state ignition

Spark plug type

NGK CMR4A

Electrode gap mm 0.7 - 0.8

Fuel Automobile gasoline

Engine Oil

SAE 10W-30 oil of API Ciassication,

Class SF or higher (4-stroke engine for automobile)

Cutting tools (cutter blade dia.) mm 230

Gear ratio 14/19

-1

DESIGNATION OF PARTS

EBH252U EBH253U

⑪

⑮

⑬

④

⑯

⑭

⑫

⑨

⑤

⑩

⑦

EBH252L EBH253L

⑮

⑬

⑩

⑨

⑭

④

⑤

⑫

⑦

⑧

⑪

⑰

⑳

③

⑲

②

⑥

①

⑱

GB DESIGNATION OF PARTS

1 Fuel tank 2 Rewind starter 3 Air cleaner 4 I-O switch (on/off) 5 Spark plug 6 Exhaust mufer 7 Clutch case 8 Rear grip

9 Hanger 10 Handle 11 Control lever

12 Control cable 13 Shaft 14 Protector 15 Gear Case/Head case 16 Handle holder 17 Cutter blade 18 Nylon cutting head 19 Fuel ller cap 20 Starter knob 21 Exhaust pipe 22 Oil gauge

MOUNTING OF HANDLE

（1）

（2）

（3）

（4）

（5）

CAUTION: Before doing any work on the Petrol Brushcutter, always stop the

engine and pull the spark plug connector off the spark plug. Always wear protective gloves!

CAUTION: Start the Petrol Brushcutter only after having assembled it

completely.

For machines with bike handle models

– Loosen knob (1). – Place handle (4) between handle clamp (2) and handle holder (3). – Adjust handle (4) to an angle that provides a comfortable working position

and then secure by rmly hand-tightening knob (1).

CAUTION: Do not forget to mount spring (5).

For machines with loop handle

– Fix a barrier to the left side of the machine together with the handle for

operator protection.

– Do not adjust position of the loop handle too close to the control grip. Keep

not less than 250 mm distance between the handle and the grip. (a distance collar is provided for this purpose.)

Engine

MOUNTING OF PROTECTOR

To meet the applicable safety provisions, only the tool/ protector combinations as indicated in the table must be used.

Be sure to use genuine MAKITA cutter blades or nylon cutting head.

– The cutter blade must be well polished, free of cracks or

breakage. If the cutter blade hits against a stone during

operation, stop the engine and check the blade immediately. – Polish or replace the cutter blade every three hours of operation. – If the nylon cutting head hits against a stone during operation,

stop the engine and check the nylon cutting head immediately.

Metal blade

Protector for metal blades

CAUTION: The appropriate protector must always be installed, for

your own safety and in order to comply with accidentprevention regulations. Operation of the equipment without the guard being in place is not permitted. The outside diameter of the cutter blade must be 230 mm (9-1/16”). Never use any blades surpassing 230 mm (9-1/16”) in outside diameter.

– In use of the metal blade, x the protector (3) to the clamp (2) with two bolts

M6 x 30 (1).

NOTE: Tighten the right and left bolts evenly so that the gap between the clamp

(2) and the protector (3) will be constant.

Otherwise, the protector sometimes may not function as specied.

Nylon cutting head

(3)

Protector for

nylon cutting head

(1)

(2)

– In cases where the nylon cord cutter is to be used, be sure to mount the

nylon cord cutter protector (4) onto the metal blade protector (3). – Mount the nylon cord cutter protector (4) by holding down its central notch

while sliding it into place from the ank of the metal blade protector (3).

– Remove tape adhered to cutter, which cuts nylon cord, on nylon cord cutter

protector (4).

CAUTION: Be sure to push in nylon cord cutter protector (4) until it is fully

inserted. Take care not to injure yourself on the cutter for cutting the nylon cord.

(3)

(4)

Notch

MOUNTING OF CUTTER BLADE OR NYLON CUTTING HEAD

Turn the machine upside down, and you can replace the cutter blade or nylon cutting head easily.

– Insert the hex wrench through the hole in the gear case and rotate the

receiver washer (4) until it is locked with the hex wrench. – Loosen the nut (1) (left-hand thread) with the socket wrench and remove the

nut (1), cup (2), and clamp washer (3).

Mounting of cutterblade with the hex wrench still in place

– Mount the cutter blade onto the shaft so that the guide of the receiver washer

(4) ts in the arbor hole in the cutter blade. Install the clamp washer (3), cup

(2), and secure the cutter blade with the nut (1).

[Tightening torque: 13 - 23 N-m]

NOTE: Always wear gloves when handling the cutter blade. NOTE: The cutter blade-fastening nut (with spring washer) is a consumable

part. If there appears any wear or deformation on the spring washer, replace the nut.

Hex wrench

(4)

(3)

(2)

(1)

Hex wrench

Mounting of nylon cutting head

– The clamp washer (3), cup (2), and nut (1) are not necessary for mounting

the nylon cutting head. The nylon cutting head should go on top of the

receiver washer (4). – Insert the hex wrench through the hole in the gear case and rotate the

receiver washer (4) until it is locked with the hex wrench. – Then screw the nylon cutting head onto the shaft by turning it counter-

clockwise. – Remove the hex wrench.

– Make sure that the blade is the left way up.

(4)

Hex wrench

Rotation

Loosen

Tighten

BEFORE START OF OPERATION

Inspection and rell of engine oil

– Perform the following procedure, with the engine cooled down.

– While keeping the engine level, remove the oil gauge, and conrm that the oil is lled within the upper and lower limit marks.

When the oil is in short in such a way that the oil gauge touches the oil only by its tip, in particular with the oil gauge remaining inserted in the

crankcase without screwing-in (Fig. 1), rell new oil near the port (Fig. 2). – For reference, the oil rell time is about 10h (10 times or 10 tanks of oil rell).

If the oil changes in color or mixes with dirt, replace it with new one. (For the interval and method of replacement, refer to P 19)

Recommended oil: SAE 10W-30 oil of API Classication, Class SF or higher (4-stroke engine for automobile) Oil volume: Approx. 0.08L

Note: If the engine is not kept upright, oil may go into around the engine, and may be relled excessively.

If the oil is lled above the limit, the oil may be contaminated or may catch re with white smoke.

Point 1 in Replacement of oil: “Oil gauge”

– Remove dust or dirt near the oil rell port, and detach the oil gauge.

– Keep the detached oil gauge free of sand or dust. Otherwise, any sand or dust adhering to the oil gauge may cause irregular oil

circulation or wear on the engine parts, which will result in troubles.

– As an example to keep the oil gauge clean, it is recommended to insert the oil gauge on its knob side into the engine cover, as shown

in Fig. 3.

If oil adheres around

this tip, rell new oil.

Fig. 1

(1) Keep the engine level, and detach the oil gauge.

Fig. 2

Upper limit

(Edge of oil rell port)

Oil gauge

Fig. 3

(2) Fill oil up to the edge of the oil rell port. (Refer to Fig. 2 of the preceding

page).

Feed oil with the lubricant rell container.

(3) Securely tighten the oil gauge. Insufcient tightening may cause oil leakage.

Point 2 in Replacement of oil: “If oil spills out”

– If oil spills out between the fuel tank and engine main unit, the oil is sucked into through the cooling air intake port, which will

contaminate the engine. Be sure to wipe out spilt oil before start of operation.

REFUELING

Handling of fuel

It is necessary to handle fuel with utmost care. Fuel may contain substances similar to solvents. Refueling must be performed in a sufciently

ventilated room or in the open air. Never inhale fuel vapor, and keep fuel away from you. If you touch fuel repeatedly or for a long time, the skin becomes dry, which may cause skin disease or allergy. If fuel enters into the eye, clean the eye with fresh water. If your eye remains still irritated, consult your doctor.

Storage period of fuel

Fuel should be used up within a period of 4 weeks, even if it is kept in a special container in a well-ventilated shade. If a special container is not used or if the container is not covered, fuel may deteriorate in one day.

STORAGE OF MACHINE AND REFILL TANK

– Keep the machine and tank at a cool place free from direct sunshine. – Never keep the fuel in the cabin or trunk.

Fuel

The engine is a four-stroke engine. Be sure to use an automobile gasoline (regular gasoline or premium gasoline).

Points for fuel

– Never use a gasoline mixture which contains engine oil. Otherwise, it will cause excessive carbon accumulation or mechanical troubles. – Use of deteriorated oil will cause irregular startup.

Refueling WARNING: INFLAMMABLES STRICTLY PROHIBITED

Gasoline used: Automobile gasoline (unleaded gasoline)

– Loosen the tank cap a little so that there will be no difference in atmospheric

pressure. – Detach the tank cap, and refuel, discharging air by tilting the fuel tank so

that the refuel port will be oriented upward. (Never rell fuel full to the oil rell

port.) – Wipe well the periphery of the tank cap to prevent foreign matter from

entering into the fuel tank. – After refueling, securely tighten the tank cap.

● If there is any aw or damage on the tank cap, replace it.

● The tank cap is consumable, and therefore should be renewed every two to

three years.

Fuel tank cap

Fuel upper limit

Fuel tank

CORRECT HANDLING OF MACHINE

Attachment of shoulder strap

– Adjust the strap length so that the cutter blade will be kept parallel with the

ground.

Detachment

For EBH252L, EBH253L

– In an emergency, push the notches (1) at both sides, and you can detach the

machine from you.

Be extremely careful to maintain control of the machine at this time. Do not

allow the machine to be deected toward you or anyone in the work vicinity.

WARNING: Failure to maintain complete control of the machine at all could

result in serious bodily injury or DEATH.

(1)

Hanger

For EBH252U, EBH253U

– In case of emergency, remove the emergency detachment lever (2) by pulling

strongly with a nger. The machine sill detach from body.

Be extremely careful to maintain control of the machine at this time. Do not

allow the machine to be deected toward you or anyone in the work vicinity.

WARNING: Failure to maintain complete control of the machine at all could

result in serious bodily injury or DEATH.

Hanger

(2)

POINTS IN OPERATION AND HOW TO STOP

Observe the applicable accident prevention regulations!

STARTING

Move at least 3 m away from the place of refuelling. Place the Petrol Brushcutter on a clean piece of ground taking care that the cutting tool does not come into contact with the ground or any other objects.

A: Cold start

1) Set this machine on a at space.

STOP

OPERATION

Lock-off lever

(1)

Throttle lever

STOP

(1)

OPERATION

Throttle lever

High speed

Low speed

EBH252L EBH253L

Low speed

High speed

Lock-off lever

EBH252U EBH253U

2) Set the I-O switch (1) to OPERATION.

3) Choke lever

Close the choke lever. Choke opening:

– Full closing in cold or when the engine is cold. – Full or half opening in restart just after stop of operation.

4) Primer pump Continue to push the primer pump until fuel enters into the primer pump. (In

general, fuel enters into the primer pump by 7 to 10 pushes.) If the primer pump is pushed excessively, an excess of gasoline returns to the fuel tank.

5) Recoil starter Pull the start knob gently until it is hard to pull (compression point). Then,

return the start knob, and pull it strongly.

Never pull the rope to the full. Once the start knob is pulled, never release

your hand immediately. Hold the start knob until it returns to its original point.

Carburetor

Primer Pump

6) Choke lever When the engine starts, open the choke lever.

– Open the choke lever progressively while checking the engine operation.

Be sure to open the choke lever to the full in the end.

– In cold or when the engine is cooled down, never open the choke lever

suddenly. Otherwise, the engine may stop.

7) Warm-up operation Continue warm-up operation for 2 to 3 minutes.

Note: – If the starter handle is pulled repeatedly when the choke lever remains at “CLOSE” position, the engine will not start easily due to

excessive fuel intake.

– In case of excessive fuel intake, remove the spark plug and pull the starter handle slowly to remove excess fuel. Also, dry the electrode

section of the spark plug.

OPEN

Caution during operation:

If the throttle lever is opened fully in a no-load operation, the engine rotation is increased to 10,000 min-1 or more. Never operate the engine at a higher speed than required and at an approximate speed of 6,000 - 8,500 min-1.

B: Startup after warm-up operation

1) Push the primer pump repeatedly.

2) Keep the throttle lever at the idling position.

3) Pull the recoil starter strongly.

4) If it is difcult to start the engine, open the throttle by about 1/3.

Pay attention to the cutter blade which may rotate.

Attention in Operation

When the engine is operated upside down, white smoke may come out from the mufer.

STOPPING

1) Release the throttle lever (2) fully, and when the

engine rpm has lowered, set the I-O switch to STOP the engine will now stop.

2) Be aware that the cutting head may not stop

immediately and allow it to slow down fully.

STOP

(1)

(2)

EBH252L EBH253L

(2)

STOP

(1)

EBH252U EBH253U

ADJUSTMENT OF LOW-SPEED ROTATION (IDLING)

When it is necessary to adjust the low-speed rotation (idling), perform it by the carburetor adjusting screw.

CHECKUP OF LOW-SPEED ROTATION

– Set the low-speed rotation to 3,000 min-1.

If it is necessary to change the rotation speed, regulate the adjusting screw

(illustrated on the right), with Phillips screwdriver. – Turn the adjusting screw to the right, and the engine rotation will increase.

Turn the adjusting screw to the left, and the engine rotation will drop. – The carburetor is generally adjusted before shipment. If it is necessary to

readjust it, please contact Authorized Service Agent.

Adjusting screw

Carburetor

RESHARPENING THE CUTTING TOOL

CAUTION: The cutting tools mentioned below must only be resharpened by an

– cutter blade

An expert resharpening and balancing service is provided by Authorized

Service Agents.

authorized facility. Manual resharpening will result in imbalances of the cutting tool causing vibrations and damage to the equipment.

NOTE: To increase the service life of the cutter blade it may be turned over

once, until both cutting edges have become blunt.

NYLON CUTTING HEAD

The nylon cutting head is a dual string trimmer head capable of both automatic and bump & feed mechanisms. The nylon cutting head will automatically feed out the proper length of nylon cord by the changes in centrifugal force caused by increasing or decreasing

rpms. However, to cut soft grass more efciently, bump the nylon cutting head

against the ground to feed out extra cord as indicated under operation section.

Operation

– Increase the nylon cutting head speed to approx. 6,000 min-1.

Low speed (under 4,800 min-1) is not suitable, the nylon cord will not feed out

properly at low speed. – The most effective cutting area is shown by the shaded area.

If the nylon cord does not feed out automatically proceed as follows:

1. Release the throttle lever to run the engine idle and then squeeze the

throttle lever fully. Repeat this procedure until the nylon cord feeds out to the proper length.

2. If the nylon cord is too short to feed out automatically with the above

procedure, bump the knob of the nylon cutting head against the ground to feed out the nylon cord.

3. If the nylon cord does not feed out with procedure 2, rewind/replace the

nylon cord by following the procedures described under “Replacing the nylon cord.”

Replacing the nylon cord

– First, stop the engine. – Press on the housing latches inward to lift off the cover, then remove the

spool.

Most effective cutting area

Idle speed

Knob

Full speed

Cover

– Hook the center of new nylon cord into the notch in the center of the spool,

with one end of the cord extending about 80 mm (3-1/8”) more than the other.

Then wind both ends rmly around the spool in the direction of the head

rotation (left-hand direction indicated by LH and right-hand direction by RH on

the side of the spool).

– Wind all but about 100 mm (3-15/16”) of the cords, leaving the ends

temporarily hooked through a notch on the side of the spool.

Press

Spool

Latches

Press

80 mm (3-1/8”)

For left hand rotation

Spool

100 mm (3-15/16”)

Notches

– Mount the spool in the housing so that the grooves and protrusions on the

spool match up with those in the housing. Keep the side with letters on

the spool visible on the top. Now, unhook the ends of the cord from their

temporary position and feed the cords through the eyelets to come out of the

housing.

Eyelets

– Align the protrusion on the underside of the cover with the slots of the

eyelets.

Then push cover rmly onto the housing to secure it.

SERVICING INSTRUCTIONS

Cover

Protrusion

Slot of eyelet

CAUTION: Before doing any work on the Petrol Brushcutter, always stop the engine and pull the plug cap off the spark plug (see “checking the

To ensure a long service life and to avoid any damage to the equipment, the following servicing operations should be performed at regular intervals.

spark plug”). Always wear protective gloves!

Daily checkup and maintenance

– Before operation, check the machine for loose screws or missing parts. Pay particular attention to the tightness of the cutter blade or nylon

cutting head.

– Before operation, always check for clogging of the cooling air passage and the cylinder ns.

Clean them if necessary. – Perform the following work daily after use:

• Clean the Petrol Brushcutter externally and inspect for damage.

• Clean the air lter. When working under extremely dusty conditions, clean the lter the severall times a day.

• Check the blade or the nylon cutting head for damage and make sure it is rmly mounted.

• Check that there is sufcient difference between idling and engagement speed to ensure that the cutting tool is at a standstill while the

engine is idling (if necessary reduce idling speed). If under idling conditions the tool should still continue to run, consult your nearest Authorized Service Agent.

– Check the functioning of the I-O switch, the lock-off lever, the control lever, and the look button.

REPLACEMENT OF ENGINE OIL

Deteriorated engine oil will shorten the life of the sliding and rotating parts to a great extent. Be sure to check the period and quantity of replacement.

ATTENTION: In general, the engine main unit and engine oil still remain hot just after the engine is stopped. In replacement of oil,

conrm that the engine main unit and engine oil are sufciently cooled down. Otherwise, there may remain a risk of

scald.

Note: If the oil lled above the limit, it may be contaminated or may catch re with white smoke.

Interval of replacement: Initially, every 20 operating hours, and subsequently every 50 operating hours Recommended oil: SAE10W-30 oil of API Classication SF Class or higher (4-stroke engine oil for automobile)

In replacement, perform the following procedure.

1) Conrm that the tank cap is tightened securely.

2) Detach the oil gauge.

Keep the oil gauge free from dust or dirt.

Fuel tank cap

Oil gauge

3) Place waste or paper near the oil rell port.

4) Detach the oil gauge, and drain oil, tilting the main unit toward the oil rell

port. Drain oil in a container for orderly disposal.

Waste or paper

5) Keep the engine level, and feed new oil up to the edge of the oil rell port.

In rell, use a lubricant rell container.

6) After rell, securely tighten the oil gauge. Insufcient tightening of the oil

gauge will lead to oil leakage.

POINTS ON OIL

– Never discard replaced engine oil in garbage, earth or sewage ditch. Disposal of oil is regulated by law. In disposal, always follow the

relevant laws and regulations. For any points remaining unknown, contact Authorized Service Agent.

– Oil will deteriorate even when it is kept unused. Perform inspection and replacement at regular intervals (replace with new oil every 6

months).

CLEANING OF AIR CLEANER

DANGER: INFLAMMABLES STRICTLY PROHIBITED

Interval of Cleaning and Inspection: Daily (every 10 operating hours)

– Turn the choke lever to the full close side, and keep the carburetor off from

dust or dirt.

– Remove the air cleaner cover-xing bolts.

– Pull the cover lower side and detach the air cleaner cover.

– If oil adheres to the element (sponge), squeeze it rmly.

– For heavy contamination:

1) Remove the element (sponge), immerse it in warm water or in waterdiluted neutral detergent, and dry it completely.

2) Clean the element (felt) with gasoline, and dry it completely.

– Before attaching the element, be sure to dry it completely. Insufcient drying

of the element may lead to difcult startup.

– Wipe out with waste cloth, oil adhering around the air cleaner cover and plate

breather.

– Immediately after cleaning is nished, attach the cleaner cover and tighten it

with xing bolts. (In remounting, rst place the upper claw, and then the lower

claw.)

Element (sponge)

Air cleaner cover

Fixing bolt

Plate

Breather Part

Element (felt)

Points in Handling Air Cleaner Element

– Clean the element several times a day, if excessive dust adheres to it. – If operation continues with the element remaining not cleared of oil, oil

in the air cleaner may fall outside, resulting in oil contamination.

Pick this part and remove the element (felt).

CHECKING THE SPARK PLUG

– Only use the supplied universal wrench to remove or to install the spark plug. – The gap between the two electrodes of the spark plug should be 0.7 - 0.8 mm

(0.028” - 0.032”). If the gap is too wide or too narrow, adjust it. If the spark plug is clogged or contaminated, clean it thoroughly or replace it.

CAUTION: Never touch the spark plug connector while the engine is running

(danger of high voltage electric shock).

SUPPLY OF GREASE TO GEAR CASE

– Supply grease (Shell Alvania 2 or equivalent) to the gear case through the

grease hole every 30 hours. (Genuine MAKITA grease may be purchased from your MAKITA dealer.)

CLEANING OF FUEL FILTER

WARNING: INFLAMMABLES STRICTLY PROHIBITED

Interval of Cleaning and Inspection: Monthly (every 50 operating hours)

Suction head in the fuel tank

– The fuel lter (1) of the suction head is used to lter the fuel required by the

carburetor.

– A periodical visual inspection of the fuel lter is to be conducted. For that

purpose open the tank cap, use a wire hook and pull out the suction head through the tank opening. Filters found to have hardened, been polluted or clogged up are to be replaced.

– Insufcient fuel supply can result in the admissible maximum speed being

exceeded. It is therefore important to replace the fuel lter at least quarterly to

ensure satisfactory fuel supply to the carburetor.

0.7 mm - 0.8 mm (0.028” - 0.032”)

Gear case

Grease hole

Fuel pipe

House clamp

Fuel

lter (1)

REPLACEMENT OF FUEL PIPE

Fuel pipe

CAUTION: INFLAMMABLES STRICTLY PROHIBITED

Interval of Cleaning and Inspection: Daily (every 10 operating hours) Replacement: Annually (every 200 operating hours)

Replace the fuel pipe every year, regardless of operating frequency. Fuel

leakage may lead to re.

If any leakage is detected during inspection, replace the oil pipe immediately.

INSPECTION OF BOLTS, NUTS AND SCREWS

– Retighten loose bolts, nuts, etc. – Check for fuel and oil leakage. – Replace damaged parts with new ones for safety operation.

CLEANING OF PARTS

– Keep the engine always clean.

– Keep the cylinder ns free of dust or dirt. Dust or dirt adhering to the ns will

cause piston seizure.

REPLACEMENT OF GASKETS AND PACKINGS

In reassembling after the engine is dismounted, be sure to replace the gaskets and packings with new ones. Any maintenance of adjustment work that is not included and described in this manual is only to be performed by Authorized Service Agents.

STORAGE

WARNING: When draining the fuel, be sure to stop the engine and conrm that the engine cools

down.

Just after stopping the engine, it may still hot with possibility of burns, inammability and re.

ATTENTION: When the machine is kept out of operation for a long time, drain up all fuel from the

fuel tank and carburetor, and keep it at a dry and clean place.

– Drain up fuel from the fuel tank and carburetor according to the following

procedure:

1) Remove the fuel tank cap, and drain fuel completely. If there is any foreign matter remaining in the fuel tank, remove it completely.

2) Pull out the fuel lter from the rell port using a wire.

3) Push the primer pump until fuel is drained from there, and drain fuel coming into the fuel tank.

4) Reset the lter to the fuel tank, and securely tighten the fuel tank cap.

5) Then, continue to operate the engine until it stops.

– Remove the spark plug, and drip several drops of engine oil through the

spark plug hole.

– Gently pull the starter handle so that engine oil will spread over the engine,

and attach the spark plug. – Attach the cover to the cutter blade. – During storage, keep the rod horizontal or keep the machine upright with the

blade edge oriented upward. (In this case, pay full attention to prevent the

machine from falling.)

Never store the machine with the cutter blade edge oriented downward.

Lubricating oil may spill out. – Keep the drained fuel in a special container in a well-ventilated shade.

Drain fuel

Humidity

Attention after long-time storage

– Before startup after long-time shutdown, be sure to replace oil (refer to P 19). Oil will deteriorate while the machine is kept out of

operation.

Fault location

Fault System Observation Cause

Engine not starting or with

difculty

Warm start problems Tank lled ignition spark

Engine starts but dies Fuel supply Tank lled Incorrect idling adjustment, carburetor contaminated

Ignition system Ignition spark O.K. Fault in fuel supply or compression system, mechanical

defect

No ignition spark STOP-switch operated, wiring fault or short circuit, spark

plug or connector defective, ignition module faulty

Fuel supply Fuel tank lled Incorrect choke position, carburetor defective, fuel supply

line bent or blocked, fuel dirty.

Compression No compression when

pulled over

Mechanical fault Starter not engaging Broken starter spring, broken parts inside of the engine

existing

Cylinder bottom gasket defective, crankshaft seals damaged, cylinder or piston rings defective or improper sealing of spark plug

Carburetor contaminated, have it cleaned

Insufcient performance Several systems may

simultaneously be affected

Fuel tank vent defective, fuel supply line interrupted, cable or STOP-switch faulty

Engine idling poor Air lter contaminated, carburetor contaminated, mufer

clogged, exhaust duct in the cylinder clogged

Item

Operating time

Before

operation

After

lubrication

Daily (10h)

30h 50h 200h

Shutdown/

rest

Corres-

ponding P

Engine oil

Tightening parts (bolt, nut)

Replace *

Inspect 21

Clean/inspect —

Inspect/clean 13

Fuel tank

Drain fuel *

Throttle lever Check function —

Stop switch Check function 17

Cutting blade Inspect 11

Low-speed rotation Inspect/adjust 17

Air cleaner Clean 20

Ignition plug Inspect 21

Cooling air duct Clean/inspect 21

Inspect 21

Fuel pipe

Replace *

—

Gear-case grease Rell 21

Fuel lter Clean/replace 21

Clearance between air intake valve and air discharge valve

Adjust *

Engine overhaul *

Carburetor Drain fuel *

*1 Perform initial replacement after 20h operation. *2 For the 200 operating hour inspection, request Authorized Service Agent or a machine shop. *3 After emptying the fuel tank, continue to run the engine and drain fuel in the carburetor.

—

TROUBLESHOOTING

Before making a request for repairs, check a trouble for yourself. If any abnormality is found, control your machine according to the description of this manual. Never tamper or dismount any part contrary to the description. For repairs, contact Authorized Service Agent or local dealership.

State of abnormality Probable cause (malfunction) Remedy

Failure to operate primer pump Push 7 to 10 times

Low pulling speed of starter rope Pull strongly

Lack of fuel Feed fuel

Clogged fuel lter Clean

Broken fuel tube Straighten fuel tube

Deteriorated fuel Deteriorated fuel makes starting more difcult.

Replace with new one. (Recommended replacement: 1 month)

Excessive suction of fuel Set throttle lever from medium speed to high

speed, and pull starter handle until engine starts. Once engine starts, cutter blade

Engine does not start

Detached plug cap Attach securely

Contaminated spark plug Clean

Abnormal clearance of spark plug Adjust clearance

Other abnormality of spark plug Replace

Abnormal carburetor Make request for inspection and maintenance.

Starter rope cannot be pulled Make request for inspection and maintenance.

Abnormal drive system Make request for inspection and maintenance.

Insufcient warm-up Perform warm-up operation

Choke lever is set to “CLOSE” although engine is warmed up.

Engine stops soon Engine speed does not increase

Cutter blade does not rotate Loosened cutter blade-tightening nut Tighten securely

Stop engine immediately

Main unit vibrates abnormally Broken, bent or worn cutter blade Replace cutter blade

Stop engine immediately

Cutter blade does not stop immediately High idling rotation Adjust

Stop engine immediately

Engine does not stop Detached connector Attach securely

Run engine at idling, and set choke lever to CLOSE

Clogged fuel lter Clean

Contaminated or clogged air cleaner Clean

Abnormal carburetor Make request for inspection and maintenance.

Abnormal drive system Make request for inspection and maintenance.

Twigs caught by cutter blade or dispersionpreventing cover.

Abnormal drive system Make request for inspection and maintenance.

Loosened cutter blade-tightening nut Tighten securely

Shifted convex part of cutter blade and cutter

blade support tting.

Abnormal drive system Make request for inspection and maintenance.

Detached throttle wire Attach securely

Abnormal drive system Make request for inspection and maintenance.

Abnormal electric system Make request for inspection and maintenance.

starts rotating. Pay full attention to cutter blade.

If engine will not start still, remove spark plug, make electrode dry, and reassemble them as

they originally are. Then, start as specied.

Set to “OPEN”

Remove foreign matter

Attach securely

When the engine does not start after warm-up operation: If there is no abnormality found for the check items, open the throttle by about 1/3 and start the engine.

+ 56 hidden pages