ENGLISH (Original instructions)
INSTRUCTION MANUAL
Cordless Multi Tool
DTM40
DTM50
IMPORTANT: Read Before Using.
012764
1
ENGLISH (Original instructions)
SPECIFICATIONS
Model DTM40 DTM50
Oscillation per minute 6,000 - 20,000 (min-1)
Oscillation angle, left/right 1.6 ﾟ (3.2 ﾟ total)
Overall length 324 mm
Standard battery cartridge
Net weight
* NOTE: For continuous operation, high capacity battery cartridge BL1430, BL1440, BL1830, BL1840 and BL1850 are recommended.
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
without dust extraction attachment
with dust extrac tion attachment
Rated voltage D.C. 14.4 V D.C. 18 V
BL1430/
BL1440
1.9 kg 1.7 kg 2.0 kg 1.8 kg
2.0 kg 1.8 kg 2.1 kg 1.9 kg
END221-2
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
Intended use
The tool is intended for sawing and cutting wood, plastic,
gypsum, non-ferrous metals, and fastening elements (e.
g. unhardened nails and staples). It is also intended for
working soft wall tiles, as well as dry sanding and
scraping of small surfaces. It is especially for working
close to edge and flush cutting.
Noise
The typical A-weighted noise level determined according
to EN60745:
･ Read instruction manual.
･ Wear safety glasses.
Cd
･ Only for EU countries
Ni-MH
Li-ion
Do not dispose of electric equipment or
battery pack together with household
waste material!
In observance of European Directive
2002/96/EC on waste electric and
electronic equipment, 2006/66/EC on
batteries and accumulators and waste
batteries and accumulators and their
implementation in accordance with
national laws, electric equipment and
battery pack that have reached the end
of their life must be collected separately
and returned to an environmentally
compatible recycling facility.
ENE080-1
ENG905-1
2
BL1415*/
BL1415N*
BL1830/ BL1840/
BL1850
BL1815*/ BL1815N*/
BL1820*
Work mode: Sanding
Sound pressure level (LpA) : 78 dB (A)
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
Work mode: Cutting with plunge cut saw blade
Model DTM40
Sound pressure level (LpA) : 82 dB (A)
Sound power level (L
Uncertainty (K) : 3 dB (A)
) : 93 dB (A)
WA
Model DTM50
Sound pressure level (LpA) : 84 dB (A)
Sound power level (L
Uncertainty (K) : 3 dB (A)
) : 95 dB (A)
WA
Work mode: Cutting with segmental saw blade
Sound pressure level (LpA) : 81 dB (A)
Sound power level (L
Uncertainty (K) : 3 dB (A)
) : 92 dB (A)
WA
Work mode: Scraping
Model DTM40
Sound pressure level (LpA) : 81 dB (A)
Sound power level (L
Uncertainty (K) : 3 dB (A)
) : 92 dB (A)
WA
Model DTM50
Sound pressure level (LpA) : 83 dB (A)
Sound power level (L
Uncertainty (K) : 3 dB (A)
) : 94 dB (A)
WA
Wear ear protection
Vibration
ENG900-1
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Work mode: Sanding
Vibration emission (ah) : 2.5 m/s2 or less
Uncertainty (K) : 1.5 m/s
2
Work mode: Cutting with plunge cut saw blade
Model DTM40
Vibration emission (ah) : 9.5 m/s
Uncertainty (K) : 1.5 m/s
2
2
Model DTM50
Vibration emission (ah) : 10.0 m/s
Uncertainty (K) : 1.5 m/s
2
2
Work mode: Cutting with segmental saw blade
Model DTM40
Vibration emission (ah) : 5.0 m/s
Uncertainty (K) : 1.5 m/s
2
2
Model DTM50
Vibration emission (ah) : 5.5 m/s
Uncertainty (K) : 1.5 m/s
2
2
Work mode: Scraping
Model DTM40
Vibration emission (ah) : 7.5 m/s
Uncertainty (K) : 1.5 m/s
2
2
Model DTM50
Vibration emission (ah) : 9.5 m/s
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
•
2
2
ENG901-1
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
•
The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
For European countries only
EC Declaration of Conformity
Makita declares that the following Machine(s):
Designation of Machine:
Cordless Multi Tool
Model No./ Type: DTM40, DTM50
Conforms to the following European Directives:
2006/42/EC
They are manufactured in accordance with the following
standard or standardized documents:
EN60745
The technical file in accordance with 2006/42/EC is
available from:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
31.12.2013
000331
Yasushi Fukaya
Director
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions.
Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
3
ENH101-17
GEA006-2
5. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
7. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
9. If operating a power tool in a damp location is
unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply. Use of an
GFCI reduces the risk of electric shock.
Personal safety
10.
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication.
moment of inattention while operating power tools
may result in serious personal injury.
11. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
12. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
13. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
14. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
15.
Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts.
Loose clothes, jewellery or
long hair can be caught in moving parts.
16. If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
Power tool use and care
17. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
18. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
19. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
20. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
21. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
A
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
22. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
23. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
Battery tool use and care
24. Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
25. Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
26. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. Shorting the battery
terminals together may cause burns or a fire.
27. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may
cause irritation or burns.
4
Loading...