Cylinder, Crankcase, Hood
45cc BRUSH CUTTER Model DBC4510
Item Part No. No. No. Used Description
1 386 100 100 1 Short Block 45cm
2 386 131 010 1 Cylinder φ43mm
3 957 132 386 1 Piston Assy φ43mm (Old 386 132 000)
4 386 132 010 1 Piston Ring φ43mm
5 385 132 030 1 Piston Pin
6 385 132 040 2 Spring Ring
7 965 527 010 1 Gasket
8 385 111 100 1 Crankcase Assy
9 385 120 100 1 Crankshaft Assy
10 960 102 129 2 Ball Bearing
11 939 620 371 1 Key
12 962 211 033 1 Needle Cage 10x14x13
13 962 900 057 1 Radial Ring 12x20x5
14 900 006 217 1 Disc 25x35x1.5 (Type 1)
3
15 962 900 024 1 Radial Ring 12x32x7 (Type 1)
962 900 060 1 Radial Seal [Replaces Items 14 & 15
(Type 1)]
16 908 505 555 4 Screw M5x55
17 913 467 304 4 Screw 6.7x30
19 385 118 011 1 Hood
21 908 605 205 4 Screw M5x10x20
22 386 110 011 1 Motor Housing
23 001 131 020 1 Nipple
24 965 452 060 1 Tube 150mm (Sold by Meter)
25 965 404 240 2 Plug
27 928 014 000 4 Cup Spring (Added)
Special parts for USA
26 980 114 201 1 Label
09-2001
Clutch Case, Ignition Coil, Flywheel
Item Part No.
1 385 217 000 1 Clutch Case Assy
2 965 403 380 2 Ring Buffer
3 965 903 062 1 Clamping Ring
4 908 006 255 1 Screw M6x25
5 913 467 254 4 Screw 6,7x25
8 010 181 000 1 Clutch Shoe, Set
9 385 184 020 1 Spring
12 385 141 012 1 Flywheel (Old 385 141 011)
13 928 308 001 1 Spring Washer
14 920 308 024 1 Hexagonal Nut M8x1
15 385 143 031 1 Ignition Coil (Old 385 143 030)
16 965 605 411 1 Plug
17 908 605 205 2 Screw M5x10x20
18 970 502 110 1 Insulating Hose 100mm
19 970 310 200 1 Ignition Cable 160mm
20 385 147 100 1 Plug Cap Includes Spring
Accessories
A01 965 603 014 1 Spark Plug
(Sold by Meter)
(Sold by Meter)
Starter
No. No. Used Description
1 385 160 103 1 Starter Assy
(Old 385 160 102)
3 957 404 691 1 Starter Grip
4 957 160 385 1 Starter Repair Set
5 385 162 020 1 Cable Drum
6 385 163 100 1 Rewind Spring
7 385 166 040 1 Starter Wheel
8 920 308 024 1 Hexagonal Nut M8x1
9 908 605 205 4 Screw M5x10x20
10 980 114 147 1 Makita Label
Special Parts for USA
9a 908 305 405 1 Screw M5x20x40
11 385 174 020 1 Muffler Guard
12 965 551 280 4 Clamping Sleeve
13 385 174 030 4 Spacer
Accessories
A02 387 164 010 1 Starter Rope φ 3.0X1.3M
SD 4100 4.0 1 Starter Rope 1/8" x 250’
2 Model DBC4510
Muffler, Air Filter
Item Part No.
1 957 174 385 1 Muffler
2 908 405 145 5 Screw M5x14
3 965 527 040 1 Gasket
4 385 174 011 1 Cooling Plate
6 965 527 030 1 Gasket
7 385 131 071 1 Intermediate Flange CPL
8 965 527 020 1 Gasket
10 385 154 010 1 Adjusting Guide
11 028 150 740 1 Choke Lever
12 385 150 030 1 Choke Linkage
13 385 150 020 1 Spring Shackle
14 915 135 130 1 Screw 3,5x13
15 001 173 060 2 Nut
16 965 527 060 1 Gasket
17 385 173 100 1 Air Filter
18 385 118 060 1 Cover
19 908 605 145 2 Screw M5x7x14
Special Parts for USA, Canada, Austrialia & New Zealand
20 385 174 301 1 Muffler Assy
21 385 174 080 1 Spark Arrester Screen CPL
Carburetor Parts (WALBRO WT-225A)
No. No. Used Description
1 385 151 001 1 Carbutetor CPL WT-225A
2 021 151 160 1 Pump Cover
3 001 151 400 1 Idle Stop Screw (S)
4 021 151 230 1 Pressure Spring
5 118 151 190 1 Screw
6 957 151 010 1 Pump Diaphragm Set
7 021 151 120 1 Diaphragm Cover
8 118 151 020 5 Screw
9 957 151 020 1 Control Diaphragm Set
10 385 151 040 1 Throttle Shaft
11 371 151 310 1 Spring
12 001 151 680 1 Throttle Shutter
13 118 151 060 2 Screw
15 108 151 350 1 Shaft Clip
18 385 151 020 1 Shaft Assy - Choke
19 001 151 350 1 Choke Shutter
20 118 151 170 1 Friction Ball
21 118 151 160 1 Friction Spring
22 001 151 420 1 Main Adjustment Screw (H)
23 021 151 530 1 Spring (H)
24 001 151 410 1 Idling Adjustment Screw (L)
25 021 151 480 1 Spring (L)
26 021 151 180 1 Screen
27 957 150 040 1 Set Control Parts
3 Model DBC4510
Fuel Tank
Item Part No.
No. No. Used Description
25 385 114 611 1 Tank Assy, Blue
26 957 114 010 1 Vent Valve CPL
27 965 452 060 1 Tube 110mm (Sold by Meter)
28 010 114 045 1 Tank Plug CPL
29 963 601 420 1 Suction Head CPL
30 963 601 150 1 Suction Head
31 928 605 500 1 Disc
32 965 452 480 1 Tube 160mm (Sold by Meter)
34 385 310 631 1 Clamping Piece, Blue
35 908 006 305 1 Screw M6x30
36 924 106 400 1 Washer
37 920 206 000 1 Hexagonal Nut M6
38 385 365 010 1 Inserting Plate
39 965 403 380 2 Ring Buffer
40 385 316 010 1 Orifice Plate
41 913 467 164 2 Screw 6,7x16
45 980 114 673 1 Label DBC4510
Handle, Bowden Cable
Item Part No.
No. No. Used Description
1 369 313 203 1 Operating Lever Assy
(Old 369 313 202)
2 385 726 070 1 Bowden Cable CPL
3 385 310 161 1 Handle
4 369 313 290 1 Handle Half, Right, CPL
5 369 313 080 1 Handle Half, Left
6 369 311 042 1 Throttle Lever (~ 1998)
369 311 080 1 Throttle Lever ( 1999 ~)
7 369 311 071 1 Spring
8 975 001 210 1 Short-Circuit Switch
9 915 735 100 Screw 3,5x10
10 965 903 080 1 Clamping Ring φ 31
11 908 006 255 1 Screw M6x25 (Old 913 660 254)
21 385 176 010 1 Retaining Clip
22 913 455 204 1 Screw 5,5x20
23 965 401 018 1 Rubber Bush
25 387 311 100 1 Handle, Left
26 957 310 610 1 Clamping Holder Set, Blue
27 900 108 555 1 Hexagonal Screw M8x55
28 924 108 400 1 Washer
29 908 005 165 2 Screw M5x16
4 Model DBC4510
Main Pipe, Bevel Gear, Protection Hood
Item Part No.
No. No. Used Description
1 010 261 020 1 Main Pipe Assy
2 385 228 030 1 Transmission Shaft
5 980 114 628 1 Label
6 980 114 148 1 Makita Label
7 980 114 119 1 Label
11 908 005 165 4 Screw M5x16
12 385 341 021 1 Plate (Old 385 341 020)
14 957 341 010 1 Line Cutter
16 908 005 125 3 Screw M5x12
20 385 200 203 1 Bevel Gear Assy
23 962 900 055 1 Radial Ring
24 900 210 104 1 Hexagonal Head Screw M10x1,25x10
25 963 604 084 1 Gasket
26 908 005 125 1 Screw M5x12
27 908 005 255 2 Screw M5x25
30 385 228 020 1 Distance Ring
33 385 224 012 1 Mounting Disc
Item Part No.
No. No. Used Description
34 385 224 022 1 Pressure Disc
35 385 228 041 1 Safety Nut M12x1,5 L
40 957 341 020 1 Protection Cover Reinforcement CPL
41 385 224 520 1 Covering Washer
Accessories
A03 010 341 612 1 Protection Hood Assy (F/Line)
(Old 010 341 611)
A04 010 341 630 1 Protection Hood CPL φ 200 (F/Blade)
010 341 640 1 Protection Hood CPL φ 225 (F/Blade)
A05 957 385 272 1 Tool Locking Syst. CPL
A06 385 218 020 1 Sliding Cup
A20 010 224 400 1 Winding Preventer Com.
5 Model DBC4510
Accessories
Item Part No.
No. No. Used Description
12 385 260 040 1 Snaphook
13 385 260 030 1 Safety Pin
14 385 260 050 1 Shoulder Protection Slips
15 385 260 060 1 Plastic Clip
Accessories
A01 965 603 014 1 Spark Plug
A02 387 164 010 1 Starter Rope φ 3 x 1.3M
SD 4100 4.0 1 Starter Rope 1/8" x 250’
A03 010 341 612 1 Protection Hood Assy (F/Line)
(Old 010 341 611)
A04 010 341 630 1 Protection Hood CPL φ 200 (F/Blade)
010 341 640 1 Protection Hood CPL φ 225 (F/Blade)
A05 957 385 272 1 Tool Locking Syst. CPL
A06 385 218 020 1 Sliding Cup
A07 385 224 300 1 Steel Bush Cutter φ 300x20mm Arbor
A08 385 224 700 1 Chisel Type Saw Blade φ 200
385 224 600 1 Chisel Type Saw Blade φ 225
A09 385 341 411 1 Protection Case for A07
A10 370 341 450 1 Protection Case for A08, A16 & A17
A11 941 719 131 1 Universal Wrench 19/13
A12 944 340 001 1 Screwdriver
A13 940 827 000 1 Angled Screwdriver
A14 370 260 100 1 Professional Harness
(Includes Item 12-15)
A15 384 260 100 1 Double Shoulder Harness
(Includes Items 12)
A16 385 224 140 1 Star Blade φ 255
A17 385 224 200 1 8 Tooth Eddy Blade
A18 385 224 500 1 Dual Line Trimming Head (LH)
A19 384 224 502 1 Dual Line Trimming Head
(Old 384 224 500 & 384 224 501)
A20 010 224 400 1 Winding Preventer Com.
A21 B-01971 1 Nylon Line .095 X 16.4’
- - - 950 004 001 1 Plastic Bag (Not Shown)
6 Model DBC4510
Loading...