Makita DA4030, DA4031 User Manual

ENGLISH (Original instructions)

INSTRUCTION MANUAL

Angle Drill

DA4030
DA4031

DOUBLE INSULATION

WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

1

003008

ENGLISH (Original instructions)

SPECIFICATIONS

Model DA4030

Capacities

No load speed (min-1) 1,200 1,200 300

Overall length (With an extended spade grip) 417 mm ( 491 mm) 462 mm (536 mm)

Safety class /II

• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

Wood

Net weight 5.5 kg 6.3 kg

Symbols

The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.

Intended use
The tool is intended for drilling in wood, metal and
plastic.

Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated in accordance with European
Standard and can, therefore, also be used from sockets
without earth wire.

･ Read instruction manual.

･ DOUBLE INSULATION

･ Only for EU countries

Do not dispose of electric equipment
together with household waste material!
In observance of European Directive
2002/96/EC on waste electric and
electronic equipment and its
implementation in accordance with
national law, electric equipment that
have reached the end of their life must
be collected separately and returned to
an environmentally compatible
recycling facility.

Auger bit 38 mm 38 mm

Self-feed bit 65 mm 65 mm 118 mm

Hole saw ----- ----- 152 mm

Steel 13 mm 13 mm

END201-5

For Model DA4031

For European countries only
Noise

The typical A-weighted noise level determined according
to EN60745:

Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)

Wear ear protection

Vibration

The vibration total value (tri-axial vector sum)
determined according to EN60745:

Work mode: drilling into metal
Vibration emission (a
Uncertainty (K) : 1.5 m/s

The declared vibration emission value has been

•

measured in accordance with the standard test
method and may be used for comparing one tool

ENE032-1

ENF002-1

with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the

power tool can differ from the declared emission
value depending on the ways in which the tool is
used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).

2

DA4031

High Low

) : 87 dB(A)

pA

) : 98 dB(A)

WA

) : 2.5 m/s2 or less

h,D

2

ENG102-2

ENG202-3

ENG901-1

A

ENH101-12

EC Declaration of Conformity

We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):

Designation of Machine:

ngle Drill

Model No./ Type: DA4031
are of series production and

Conforms to the following European Directives:

And are manufactured in accordance with the following
standards or standardised documents:

The technical documentation is kept by our authorised
representative in Europe who is:

000230

98/37/EC until 28th December 2009 and then with
2006/42/EC from 29th December 2009

EN60745

Makita International Europe Ltd,
Michigan, Drive, Tongwell,
Milton Keynes, MK15 8JD, England

30th January 2009

Tomoyasu Kato

Director

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, JAPAN

GEA005-2

General Power Tool Safety
Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or
serious injury.

Save all warnings and
instructions for future reference.

The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.

2. Do not operate power tools in explosive

atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

3. Keep children and bystanders away while
operating a power tool. Distractions can cause

you to lose control.

Electrical safety

4. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will

reduce risk of electric shock.

5. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.

7. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords

increase the risk of electric shock.

8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.

9. If operating a power tool in a damp location is

unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply. Use of an

GFCI reduces the risk of electric shock.

Personal safety

10. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while

operating power tools may result in serious
personal injury.

11. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.

12. Prevent unintentional starting. Ensure the

switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools

with your finger on the switch or energising power
tools that have the switch on invites accidents.

13. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.

14. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.

15. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing, and gloves

3