Makita CORDLESS ANGLE DRILL DA390D, DA390DW Instruction Manual
Cordless
Angle
Drill
Capacities
Steel Wood
Wood
screw
10
mm
(3/8”) MODEL DA390D
10
mm
(3/8”)
MODEL DA390DW
With
Fast
Charger
weight
No
load speed Dimensions
(L x W
x
HI
(RPMI
INSTRUCTION MANUAL
10
mm
(318”)
SPEC
IF
I
CAT I 0
N
S
335
mm
x
59
mm
x
115
mm
(13-1/4” x 2-3/8” x 4-1/2”1
1.3 kg
12.9
Ibsl
800
12
mm
4.5
mm
x
20
mm
(15132”) (3116“ x 314”)
Model DA390D
Battery Cartridge 9000 Model DC9700 Fast Charger
Voltage
I
Charging time
I
Input
I
output
9.6 V
I
1 Hr.
I
A.C.
only 50
Hz
-
60 Hz
I
D.C.
7.2
V ~ 9.6
V
*
Manufacturer reserves the right to change specifications without notice.
*
Note: Specifications may differ from country to country.
IMPORTANT
SAFETY INSTRUCTIONS
(For
All
Tools)
WARNING:
WHEN USING ELECTRIC TOOLS, BASIC SAFE-
TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO
SONAL INJURY, INCLUDING THE FOLLOWING:
REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER-
READ
ALL
INSTRUCTIONS.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
CONSIDER WORK AREA ENVIRONMENT. Don’t use power tools
in
damp
or wet locations. Keep work area well
lit.
Don’t expose power tools to rain.
Don’t use tool
in
presence of flammable liquids or gases.
KEEP CHILDREN AWAY. All visitors should be kept away from work area.
Don’t let visitors contact tool or extension cord.
STORE IDLE TOOLS. When not
in
use, tools should be stored
in
dry, and high
or locked-up place
-
out of reach of children.
DON’T FORCE TOOL.
It
will do the job better and safer at the rate for which
it
was intended.
USE RIGHT TOOL. Don‘t force small tool or attachment to do the job of a
heavy-duty tool. Don‘t use tool for purpose not intended.
DRESS PROPERLY. Don’t wear loose clothing or jewelry. They can be caught
in moving parts. Rubber gloves and non-skid footwear are recommended
when working outdoors. Wear protective hair covering to contain long hair.
USE SAFETY GLASSES. Also use face or dust mask if cutting operation is
dusty.
DON’T ABUSE CORD. Never carry tool by cord or yank
it
to
disconnect from
receptacle. Keep cord from heat, oil, and sharp edges.
SECURE WORK. Use clamps or
a
vise
to
hold work. It’s safer than using
your hand and
it
frees both hands to operate tool.
DON’T OVERREACH. Keep proper footing and balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and
safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Inspect extension cords periodically and replace
if
damaged. Keep handles dry, clean, and free from oil and grease.
DISCONNECT TOOLS. When not
in
use, before servicing, and when chang-
ing accessories, such as blades, bits, cutters.
2
14.
15.
16.
17.
18.
19.
20.
REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are removed from tool before turning
it
on.
AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger
on switch. Be sure switch
is
OFF when plugging in.
OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only
extension cords intended for use outdoors and
so
marked.
STAY ALERT. Watch what you are doing, use common sense. Don’t operate
tool when you are tired.
CHECK DAMAGED PARTS. Before further use of the tool, a guard or other
part that is damaged should be carefully checked to determine that
it
will
operate properly and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual.
Have defective switches replaced by authorized service center. Don’t use
tool
if
switch does not turn
it
on and off.
GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded
surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.
REPLACEMENT PARTS. When servicing, use only identical replacement parts.
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle,
outlet, etc.) be sure the voltage supplied is the same as that specified on the
nameplate of the tool. A power source with voltage greater than that specified
for the tool can result in SERIOUS INJURY to the user
-
as well as damage to
the tool. If in doubt,
DO
NOT PLUG IN THE TOOL. Using a power source with
voltage less than the nameplate rating is harmful to the motor.
3
IMPORTANT SAFETY INSTRUCTIONS
Length of Cord (Feet)
25
50
100
AWG Size of Cord
18 18
18
I.
SAVE THESE INSTRUCTIONS
-
This manual
150
16
9.
Do not operate charger with damaged cord or plug
-
replace them im-
mediately.
IO.
Do not operate charger if
it
has received a sharp blow, been dropped, or
otherwise damaged
in
any way; take
it
to a qualified serviceman.
11.
Do not disassemble charger or battery cartridge; take
it
to a qualified
serviceman when service or repair is required. Incorrect reassembly may
result in a risk
of
electric shock or fire.
12.
To reduce risk of electric shock, unplug charger from outlet before attempt-
ing any maintenance or cleaning. Turning off controls
will
not reduce this risk.
4
Loading...