Makita 6201D Instruction Manual
Cordless Driver Drill
Capacities
Steel Wood Wood screw Machine screw
Equipped with Electric Brake
MODEL 6201D
MODEL 6201DW
With Fast Charger
Dimensions
Net
No
load speed IRPM)
High Low
1L
x W x
H) weight
INSTRUCTION MANUAL
*
Battery Cartridge 9100
Voltage Charging time
9.6
V
1
Hr.
SPECIFICATIONS
Model
DC9700 Fast Charger
Input output
A.C.
only
50
Hz - 60
Hz
D.C.
7.2
V,
9
6
V
Model
6201D
10
mm
21
mm
6.1
mm
x
55
mm
-
-
350
237
mm
x
57
mm x 243
mm
1.7
kg
(318'7
1
113116")
I
l1/4"
x
2-3/16")
I
6mm
'"4''
1
1
I
19-318" x 2-114" x 9-9/16") I 13.7
lbsl
I
M
PO
RTANT
SAFETY INSTRUCTIONS
(For
All Tools)
WARNING:
WHEN USING ELECTRIC TOOLS, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE
THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL
INJURY, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
1.
2.
3.
4.
5.
6.
7.
a.
9.
IO.
11.
12.
13.
2
KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
CONSIDER WORK AREA ENVIRONMENT. Don't use power tools
in
damp
or wet locations. Keep work area well
lit.
Don't expose power tools to rain.
Don't use tool
in
presence of flammable liquids or gases.
KEEP CHILDREN AWAY. All visitors should be kept away from work area.
Don't let visitors contact tool or extension cord.
STORE IDLE TOOLS. When not
in
use, tools should be stored in dry, and high
or locked-up place
-
out of reach of children.
DON'T FORCE TOOL.
It
will do the job better and safer at the rate for which
it
was intended.
USE RIGHT TOOL. Don't force small tool or attachment to do the job of a
heavy-duty tool. Don't use tool for purpose not intended.
DRESS PROPERLY. Don't wear
loose
clothing or jewelry. They can be caught
in moving parts. Rubber gloves and non-skid footwear are recommended
when working outdoors. Wear protective hair covering to contain long hair.
USE SAFETY GLASSES. Also use face or dust mask if cutting operation
is
dusty.
DON'T ABUSE CORD. Never carry tool by cord or yank
it
to disconnect from
receptacle. Keep cord from heat, oil, and sharp edges.
SECURE WORK. Use clamps or a vise to hold work. It's safer than using
your hand and
it
frees both hands to operate tool.
DON'T OVERREACH. Keep proper footing and balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and
safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Inspect extension cords periodically and replace if
damaged. Keep handles dry, clean, and free from oil and grease.
DISCONNECT TOOLS. When not
in
use, before servicing, and when chang-
ing accessories, such as blades, bits, cutters.
14.
REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are removed from tool before turning
it
on.
15.
AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger
on switch. Be sure switch is
OFF
when plugging
in.
16.
OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only
extension cords intended for use outdoors and
so
marked.
17.
STAY ALERT. Watch what you are doing, use common sense. Don't operate
tool when you are tired.
18.
CHECK DAMAGED PARTS. Before further use of the tool, a guard or other
part that is damaged should be carefully checked to determine that
it
will
operate properly and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation. A guard or other part
that is damaged should be properly repaired or replaced
by
an authorized
service center unless otherwise indicated elsewhere
in
this instruction
manual. Have defective switches replaced by authorized service center. Don't
use tool
if
switch does not
turn
it
on and off.
19.
GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded
surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.
20.
REPLACEMENT PARTS. When servicing, use only identical replacement parts.
VOLTAGE WARNING: Before connecting the tool
to
a
power source (receptacle,
outlet, etc.) be sure the voltage supplied is the same as that specified on the
nameplate of the tool. A power source with voltage greater than that specified
for the tool can result in SERIOUS INJURY to the user
-
as well as damage to
the tool. If
in
doubt, DO NOT PLUG IN THE TOOL. Using a power source with
voltage less than the nameplate rating is harmful to the motor.
3
I.
SAVE THESE INSTRUCTIONS
-
This manual
Length of Cord (Feet)
25
AWG Size of Cord
18
50
100 150
18 18
16
4
ADDITIONAL SAFETY RULES
FOR
CHARGER
&
BATTERY CARTRIDGE
1.
Do
not charge Battery Cartridge when temperature is BELOW 10°C
(50OF)
2.
Do
not attempt to use a step-up transformer, an engine generator or DC power
3.
Do
not allow anything to cover or clog the charger vents.
4.
Always cover the battery terminals with the battery cover when the battery
5.
A battery short can cause a large current flow, overheating, possible burns
or ABOVE
4OoC
(104OF).
receptacle.
cartridge is not used.
and even a breakdown.
(1) Do not touch the terminals with any conductive material.
(2)
Avoid storing battery cartridge
in
a container with other metal objects such
(31
Do
not expose battery cartridge to water or rain.
ture may reach or exceed 5OoC (122OF).
completely worn out. The battery cartridge can explode in a fire.
as nails, coins, etc.
6.
Do
not store the tool and Battery Cartridge in locations where the tempera-
7.
Do
not incinerate the Battery Cartridge even
if
it
is severely damaged or is
ADDITIONAL SAFETY RULES
1.
Be aware that this tool is always in an operating condition, because
it
does
2.
Always be sure
you
have a firm footing.
3.
Hold the tool firmly.
4.
Keep hands away from rotating parts.
5.
When drilling into walls, floors or wherever "live" electrical wires may be
encountered,
DO
NOT TOUCH ANY METAL PARTS OF THE TOOL!
Hold the tool only by the insulated grasping surfaces to prevent electric shock
if you drill into a "live" wire.
not have
to
be
plugged into an electrical outlet.
Be sure no one is below when using the tool
in
high locations.
6.
Do
not leave the tool running. Operate the tool only when hand-held.
7.
Do
not touch the drill
bit
or the workpiece immediately after operation; they
may be extremely hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
5
Loading...