Makita 6040DW User Manual
Cordless
MODEL 6040D
MODEL 6040DW
With Quick
INSTRUCTION MANUAL
Drill
Charger
SPECIFICATIONS
Capacities
SteelIWood Wood
10
mm
1318")
Model DC4100A
Manufacturer reserves the right to change specifications without notice.
Note: Specifications may differ from country to country.
A
C.
I
Quick Charger
Input
only
50
4.5
(3116''
~~
Hz
mm
-
screw
x
x
60
20
314")
Hz
mm
No
load speed Dimensions
IRPM)
output
DC
I
6
4V
450
I
I
195
(7-518"
mm
IL
x
x
x W x
48
1-718"
I
I
mm
H)
x
x
166
6-112")
mm
I
Charging time
3
Hr
Not
weight
0.8
11.7
kg
Ibs)
IMPORTANT
SAFETY
WARNING:
WHEN USING ELECTRIC TOOLS, BASIC SAFE-
INSTRUCTIONS
(For
All
Tools)
TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO
REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING:
READ
1.
2.
3.
4.
5.
6.
7.
8.
9.
IO.
11.
12.
13.
ALL
KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
CONSIDER WORK AREA ENVIRONMENT. Don't use power tools
or wet locations. Keep work area well
Don't use tool
KEEP CHILDREN AWAY. All visitors should be kept away from work area.
Don't
let
STORE IDLE TOOLS. When not
or locked-up place
DON'T FORCE TOOL.
it
was intended.
USE RIGHT TOOL. Don't force small tool
heavy-duty tool. Don't use tool for purpose not intended.
DRESS PROPERLY. Don't wear loose clothing
in moving parts. Rubber gloves and non-skid footwear are recommended
when working outdoors. Wear protective hair covering to contain long hair.
USE SAFETY GLASSES. Also use face or dust mask if cutting operation is
dusty.
DON'T ABUSE CORD. Never carry tool by cord or yank
receptacle. Keep cord from heat, oil, and sharp edges.
SECURE WORK. Use clamps or a vise to hold work. It's safer than using
your hand and
DON'T OVERREACH. Keep proper footing and balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and
safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Inspect extension cords periodically and replace
damaged. Keep handles dry, clean, and free from oil and grease.
DISCONNECT TOOLS. When not
ing accessories, such as blades, bits, cutters.
INSTRUCTIONS.
lit.
Don't expose power tools to rain.
in
presence of flammable liquids or gases.
visitors contact tool or extension cord.
in
use, tools should be stored
-
out
of
reach of children.
It
will do the job better and safer at the rate for which
or
attachment to do the job of a
or
jewelry. They can be caught
it
frees both hands to operate tool.
in
use, before servicing, and when chang-
in
damp
in
dry, and high
it
to disconnect from
if
2
14.
REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are removed from tool before turning
it
on.
15.
AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool
on switch. Be sure switch is OFF when plugging in.
16.
OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only
extension cords intended for use outdoors and
17.
STAY ALERT. Watch what you are doing, use common sense. Don't operate
tool when you are tired.
18.
CHECK DAMAGED PARTS. Before further use of the tool, a guard
part that is damaged should be carefully checked to determine that
operate properly and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual.
Have defective switches replaced by authorized service center. Don't use
tool if switch does not turn
19.
GUARD AGAINST ELECTRIC SHOCK. Prevent body contact
surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.
20.
REPLACEMENT PARTS. When servicing, use only identical replacement parts.
it
on and off.
so
marked.
with
with
finger
or
other
it
will
grounded
VOLTAGE WARNING: Before connecting the tool to
outlet, etc.1 be sure the voltage supplied is the same as that specified on the
nameplate of the tool. A power source with voltage greater than that specified
for the tool can result in SERIOUS INJURY to the user
the tool. If
voltage less than the nameplate rating is harmful to the motor.
in
doubt, DO NOT PLUG IN THE TOOL. Using a power source with
a
power source (receptacle,
-
as well as damage to
3
IMPORTANT SAFETY INSTRUCTIONS
I.
SAVE
contains important safety and operating instructions for battery charger.
2.
Before using battery charger, read all instructions and cautionary markings
on
(1)
3.
CAUTION - To reduce risk of injury, charge only MAKITA type rechargeable batteries. Other types of batteries may burst causing personal injury
and damage.
4.
Do
not expose charger to rain
5.
Use of an attachment not recommended or sold by the battery charger
manufacturer may result
6.
To reduce risk of damage to electric plug and cord,
cord when disconnecting charger.
7.
Make sure cord is located
or
otherwise subjected to damage or stress.
8.
Do
not operate charger with damaged cord
mediately.
9.
Do
not operate charger if
otherwise damaged
IO.
Do
not disassemble charger or battery cartridge; take
serviceman when service or repair is required. Incorrect reassembly may
result in a risk of electric shock
1 1.
To reduce risk of electric shock, unplug charger from outlet before attempting
any maintenance or cleaning. Turning off controls will not reduce this risk.
THESE
battery charger,
in
INSTRUCTIONS
(2)
battery, and
or
in
a risk of fire, electric shock, or injury to persons.
so
that
it
has received a sharp blow, been dropped, or
any way; take
or
13)
product using battery.
snow.
pull
it
will not be stepped on, tripped over,
or
plug - replace them im-
it
to a qualified serviceman.
fire.
-
This manual
by plug rather than
it
to a qualified
4
Loading...