Makita 6040D Instruction Manual
Cordless
Drill
No
load speed Dimensions
IL
x W x
H)
Capacities
IRPM)
SteelIWood Wood
screw
MODEL 6040D
MODEL 6040DW
With Quick
Charger
Not
weight
INSTRUCTION MANUAL
SPECIFICATIONS
10
mm
1318")
I
(3116''
x
314")
4.5
mm
x
20
mm
450
I
195
mm
x
48
mm
x
166
mm
0.8
kg
(7-518"
x
1-718"
x
6-112")
I
11.7
Ibs)
Model DC4100A
Quick Charger
Input
I
output
I
Charging time
3
Hr
I
DC
6
4V
I
~~
A
C.
only
50
Hz
-
60
Hz
Manufacturer reserves the right to change specifications without notice.
Note: Specifications may differ from country to country.
IMPORTANT
SAFETY
INSTRUCTIONS
(For
All
Tools)
WARNING:
WHEN USING ELECTRIC TOOLS, BASIC SAFE-
REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER-
TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO
SONAL INJURY, INCLUDING THE FOLLOWING:
READ
ALL
INSTRUCTIONS.
1.
2.
3.
4.
5.
6.
7.
8.
9.
IO.
11.
12.
13.
2
KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
CONSIDER WORK AREA ENVIRONMENT. Don't use power tools
in
damp
or wet locations. Keep work area well
lit.
Don't expose power tools to rain.
Don't use tool
in
presence of flammable liquids or gases.
KEEP CHILDREN AWAY. All visitors should be kept away from work area.
Don't
let
visitors contact tool or extension cord.
STORE IDLE TOOLS. When not
in
use, tools should be stored
in
dry, and high
or locked-up place
-
out
of
reach of children.
DON'T FORCE TOOL.
It
will do the job better and safer at the rate for which
it
was intended.
USE RIGHT TOOL. Don't force small tool
or
attachment to do the job of a
heavy-duty tool. Don't use tool for purpose not intended.
DRESS PROPERLY. Don't wear loose clothing
or
jewelry. They can be caught
in moving parts. Rubber gloves and non-skid footwear are recommended
when working outdoors. Wear protective hair covering to contain long hair.
USE SAFETY GLASSES. Also use face or dust mask if cutting operation is
dusty.
DON'T ABUSE CORD. Never carry tool by cord or yank
it
to disconnect from
receptacle. Keep cord from heat, oil, and sharp edges.
SECURE WORK. Use clamps or a vise to hold work. It's safer than using
your hand and
it
frees both hands to operate tool.
DON'T OVERREACH. Keep proper footing and balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and
safer performance. Follow instructions for lubricating and changing accesÂsories. Inspect tool cords periodically and if damaged, have repaired by autho-
rized service facility. Inspect extension cords periodically and replace
if
damaged. Keep handles dry, clean, and free from oil and grease.
DISCONNECT TOOLS. When not
in
use, before servicing, and when chang-
ing accessories, such as blades, bits, cutters.
14.
REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are removed from tool before turning
it
on.
15.
AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool
with
finger
on switch. Be sure switch is OFF when plugging in.
16.
OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only
extension cords intended for use outdoors and
so
marked.
17.
STAY ALERT. Watch what you are doing, use common sense. Don't operate
tool when you are tired.
18.
CHECK DAMAGED PARTS. Before further use of the tool, a guard
or
other
part that is damaged should be carefully checked to determine that
it
will
operate properly and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced by an authorized servÂice center unless otherwise indicated elsewhere in this instruction manual.
Have defective switches replaced by authorized service center. Don't use
tool if switch does not turn
it
on and off.
19.
GUARD AGAINST ELECTRIC SHOCK. Prevent body contact
with
grounded
surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.
20.
REPLACEMENT PARTS. When servicing, use only identical replacement parts.
VOLTAGE WARNING: Before connecting the tool to
a
power source (receptacle,
outlet, etc.1 be sure the voltage supplied is the same as that specified on the
nameplate of the tool. A power source with voltage greater than that specified
for the tool can result in SERIOUS INJURY to the user
-
as well as damage to
the tool. If
in
doubt, DO NOT PLUG IN THE TOOL. Using a power source with
voltage less than the nameplate rating is harmful to the motor.
3
IMPORTANT SAFETY INSTRUCTIONS
I.
SAVE
THESE
INSTRUCTIONS
-
This manual
contains important safety and operating instructions for battery charger.
2.
Before using battery charger, read all instructions and cautionary markings
on
(1)
battery charger,
(2)
battery, and
13)
product using battery.
3.
CAUTION
-
To reduce risk of injury, charge only MAKITA type recharge-
able batteries. Other types of batteries may burst causing personal injury
and damage.
4.
Do
not expose charger to rain
or
snow.
5.
Use of an attachment not recommended or sold by the battery charger
manufacturer may result
in
a risk of fire, electric shock, or injury to persons.
6.
To reduce risk of damage to electric plug and cord,
pull
by plug rather than
cord when disconnecting charger.
7.
Make sure cord is located
so
that
it
will not be stepped on, tripped over,
or
otherwise subjected to damage or stress.
8.
Do
not operate charger with damaged cord
or
plug
-
replace them im-
mediately.
9.
Do
not operate charger if
it
has received a sharp blow, been dropped, or
otherwise damaged
in
any way; take
it
to a qualified serviceman.
IO.
Do
not disassemble charger or battery cartridge; take
it
to a qualified
serviceman when service or repair is required. Incorrect reassembly may
result in a risk of electric shock
or
fire.
1 1.
To reduce risk of electric shock, unplug charger from outlet before attempting
any maintenance or cleaning. Turning off controls will not reduce this risk.
4
Loading...