Makita 4351FCT, 4351FCTJ Manual

ENGLISH

INSTRUCTION MANUAL

Jig Saw

4351T

4351CT

4351FCT

008029

DOUBLE INSULATION

WARNING:

For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

ENGLISH

SPECIFICATIONS

Model			4351T	4351CT	4351FCT
Length of stroke			26 mm	26 mm	26 mm
		Wood	135 mm	135 mm	135 mm
Max. cutting capacities		Steel	10 mm	10 mm	10 mm
		Aluminum	20 mm	20 mm	20 mm
Strokes per minute (min-1)			2,800	800 - 2,800	800 - 2,800
Overall length			271 mm	271 mm	271 mm
Net weight			2.4 kg	2.5 kg	2.5 kg
Safety class				/II

•Due to our continuing programme of research and development, the specifications herein are subject to change without notice.

•Note: Specifications may differ from country to country.

END201-2

Symbols

The following show the symbols used for the equipment. Be sure that you understand their meaning before use. Read instruction manual.

DOUBLE INSULATION

Only for EU countries

Do not dispose of electric equipment together with household waste material! In observance of European Directive 2002/96/EC on waste electric and electronic equipment and its implementation in accordance with national law, electric equipment that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.

ENE019-1

Intended use

The tool is intended for the sawing of wood, plastic and metal materials. As a result of the extensive accessory and saw blade program, the tool can be used for many purposes and is very well suited for curved or circular cuts.

ENF002-1

Power supply

The tool should be connected only to a power supply of the same voltage as indicated on the nameplate, and can only be operated on single-phase AC supply. They are double-insulated in accordance with European Standard and can, therefore, also be used from sockets without earth wire.

For Model 4351T

ENG101-1

For European countries only Noise

The typical A-weighted noise level determined according to EN60745-2-11:

Sound pressure level (LpA) : 85 dB(A) Uncertainty (K) : 3 dB(A)

The noise level under working may exceed 85 dB (A).

Wear ear protection.

ENG220-1

Vibration

The vibration total value (tri-axial vector sum) determined according to EN60745-2-11:

Work mode : cutting chipboard

Vibration emission (ah,CW) : 7 m/s2 Uncertainty (K) : 1.5 m/s2

ENG304-1

Work mode : cutting sheet metal

Vibration emission (ah,CM) : 4.5 m/s2 Uncertainty (K) : 1.5 m/s2

For Model 4351CT, 4351FCT

ENG101-1

For European countries only Noise

The typical A-weighted noise level determined according to EN60745-2-11:

Sound pressure level (LpA) : 85 dB(A) Uncertainty (K) : 3 dB(A)

The noise level under working may exceed 85 dB (A).

Wear ear protection.

ENG220-1

Vibration

The vibration total value (tri-axial vector sum) determined according to EN60745-2-11:

Work mode : cutting chipboard

Vibration emission (ah,CW) : 6.5 m/s2 Uncertainty (K) : 1.5 m/s2

2

ENG304-1

Work mode : cutting sheet metal

Vibration emission (ah,CM) : 4.5 m/s2 Uncertainty (K) : 1.5 m/s2

ENH101-7

EC-DECLARATION OF CONFORMITY

Model; 4351T, 4351CT, 4351FCT

We declare under our sole responsibility that this product is in compliance with the following standards of standardized documents;

EN60745, EN55014, EN61000 in accordance with Council Directives, 2004/108/EC, 98/37/EC.

CE2006

000230

Tomoyasu Kato

Director Responsible Manufacturer:

Makita Corporation

3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN Authorized Representative in Europe:

Makita International Europe Ltd.

Michigan Drive, Tongwell, Milton Keynes, Bucks MK15 8JD, ENGLAND

GEA001-3

General Safety Rules

WARNING! Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

SAVE THESE INSTRUCTIONS.

Work area safety

1.Keep work area clean and well lit. Cluttered and dark areas invite accidents.

2.Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

3.Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

4.Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

5.Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

6.Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

7.Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

8.When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

Personal safety

9.Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

10.Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

11.Avoid accidental starting. Ensure the switch is in the off-position before plugging in. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents.

12.Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

13.Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

14.Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

15.If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.

Use of these devices can reduce dust-related

hazards.

Power tool use and care

16.Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

17.Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot

3

be controlled with the switch is dangerous and must be repaired.

Holding the work by hand or against your body leaves it unstable and may lead to loss of control.

18.Disconnect the plug from the power source 3. Always use safety glasses or goggles.

and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

Ordinary eye or sun glasses are NOT safety glasses.

4.Avoid cutting nails. Inspect workpiece for any nails and remove them before operation.

5.Do not cut oversize workpiece.

19.Store idle power tools out of the reach of 6. Check for the proper clearance beyond the

children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

20.Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

21.Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

22.Use the power tool, accessories and tool bits etc. in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from

those intended could result in a hazardous situation.

Service

23.Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

24.Follow instruction for lubricating and changing accessories.

25.Keep handles dry, clean and free from oil and grease.

GEB016-1

workpiece before cutting so that the blade will not strike the floor, workbench, etc.

7.Hold the tool firmly.

8.Make sure the blade is not contacting the workpiece before the switch is turned on.

9.Keep hands away from moving parts.

10.Do not leave the tool running. Operate the tool only when hand-held.

11.Always switch off and wait for the blade to come to a complete stop before removing the blade from the workpiece.

12.Do not touch the blade or the workpiece immediately after operation; they may be extremely hot and could burn your skin.

13.Do not operate the tool at no-load unnecessarily.

14.Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data.

15.Always use the correct dust mask/respirator for the material and application you are working with.

SAVE THESE INSTRUCTIONS.

WARNING:

MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to jig saw safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury.

1.Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.

2.Use clamps or another practical way to secure and support the workpiece to a stable platform.

4