How it Works
Majestic Appliances
Loading...
WQP8-9122
Instruction Manual
14 pgs1.06 Mb0

Majestic Appliances 17-1021, WQP8-9122 Installation Instruction

Installation Instruction
PN 17-1021 WQP8-9122
MAJESTIC APPLIANCES DIV OF MSI 3201 Northwest Lower River Road, #9, Vancouver, WA 98660 USA
WWW.majesticappliances.com
r---------------------------------------------------------------------------------------------------------r---
Installation Preparation
MATERIALS YOU WILL NEED
o
2 #8 flat head wood screws, 5/8" long to secure dishwasher to underside of countertop or to side of cabinetry (Taped to top or side of dishwasher)
o
Side and top trim pieces
o
Ferrule, compression nut and 900Elbow (3/8"NPT external thread on one end, opposite end sized to fit water supply)
o
Thread seal tape
o
UL Listed wire nuts
Materials For New Installations Only:
o
Air gap for drain hose, if req uired
o
Waste tee for house plumbing, if applicable
o
Electrical cable or power cord, if applicable
o
Screw type Hose clamps
o
Strain relief for electrical connection.
o
Hand shut-off valve (recommended)
o
Water line 3/8" min. copper or 112" min. Plastic (plastic must be tested for temperature and pressure)
o
Coupler for extending drain line, if applicable
E
Wood Screws
Trim Pieces
Air Gap
Ii
~
~
MID)
@])eiU)
Hand
Thread
Waste Tee
Shut-off
Seal Tape
Wire Nuts
Valve
900Elbow, Ferrule and Compression nut
Electrical Cable (or Power cord)
Hot Water Line
~~
0
rn
Screw Tape
Strain Relief
Coupler
Hose Clamps
TOOLS
o
Head screwdriver
o
5/16" and" nutdriver
o
6" Adjustable wrench
o
Level
o
Carpenters square
o
Measuring tape
o
Safety glasses
o
Flashlight
o
Bucket to catch water when flushing the line
o
15/16" socket (optional for skid removal)
o
Gloves
o
Tubing cutter
o
Drill and approprivate bits
o
Hole saw set
Level
I"
Carpenters Square
Hole Saw Sei
Flashlight
Tubing Cutter
Safety Glasses
Gloves
6" Adj ustable
Wrench
Measuring Tape
Drilland Bits
1
Installation Preparation
UNIT DIMENSIONS WAYS OF DRAIN CONNECTIONS
23"
33"-35'
Figure 1
DEPTH: 23"(5S0mm) WIDTH: lS"(450mm)
HEIGHT: 33"-35"
(S40-S90mm)
PREPARE THE LOCATION
The dishwasher should be installed in the kitchen near
the sink, which will easier connect the water and drain suppJy lines.
A build-in dishwasher must be enclosed on the top, both
sides and the back.
33"35-112" Underside of
Countertop to Flo r
,/------'-----i
Min.
IS"
6"
Floor must be Even With Room Floor
Figure 2
DEPTH: 24"(610mm) WIDTH: lS"(460mm)
HEIGHT: 33"-35-1I2"(S40-900mm)
CONNER INSTALLATION
If you install the dishwasher
into a corner, allow 2" min. Clearance between dishwasher
and adjacent cabinet, wall or other appliances. Allow 22" min. Clearance from the front of the dishwasher for door opening.
Minimum Clearance
¥
C
I/r.---------"II ~
22"
Figure 3
The type of drain installation depends on the following question.
o
Air gap is required by the local codes and ordinances
o
Waste tee less than 18" minimum above the floor.
Ifboth answers are yes, choose A and B. Or you should choose C and D ..
A) air gap with waste tee
r-0
A
Figure 4
B) air gap with disposer
r-0
A
Figure 5
Figure 6
D) disposer ~
Figure 7
2
Installation Preparation
PREPARE ELECTRICAL WIRING
A WARNING!
FORPERSONALSAFET~ Remove house fuse or open circuit breaker before beginning installation. Do not use an extension cord or adapter
plug with this appliance.
GROUNDING INSTRUCTIONS--Power Cord Models This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of
electric shock by providing a path ofleast resistance for electric current. This appliance is equipped with a cord
having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate
outlet that is installed in an accordance with all local codes and ordinances.
A WARNING!
Improper connection of the equipment-grounding conductor can result in a risk of electric shock .Check with a qualified
electrician or service representative if you are in doubt wether the appliance is properly grounded. Do you modify the plug
provided with the appliance; Hit will not fit the outlet, have a proper outlet installed by a qualified electrician.
GROUNDING INSTRUCTIONS--Cable Direct
This appliance must be connected to a grounded metal, permanent wiring system ,or an equipment-grounding
conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on appliance.
ELECTRICAL REQUIREMENT
This dishwasher is designed for operation on an adequately wired individual 120VAC, 60HZ, and connected to an individual, properly grounded branch circuit, protected by a 15 or 20 amp circuit breaker or time-delay fuse.
lf
the electric supply provided does not meet the above specifications, it is recommended that a licensed electrician
install an approved outlet. Your dishwasher circuit should not be used for any other appliance while the dishwasher is in operation as the dishwasher requires the full capacity ofthe circuit. lf
the wall socket you plug the dishwasher's power cord into is controlled by a switch, turn off the switch before
installation.
1 The power-supply socket for the appliance shall be
installed in a cabinet or on a wall adjacent to the undercounter space in which the appliance is to be installed.
2 There shall be an opening through the partition
between the compartments specified in 1 that is . large enough for the attachment plug to pass through. The longest dimension of the opening shall not be
more than 38mm.
3 The edges of the opening specified in 2 shall, ifthe
partition is wood, be smooth and rounded, or, if the partition is metal, be covered with an edge protector provided for this purpose by the manufacturer; and
Figure 8
4 Care shall be exercised, when the appliance is
installed or removed, to reduce the likelihood of damage to the power-supply cord.
ELECTRICAL CONNECTION
Electrical connection is on the right front of dishwasher. For cable direct connections the cable must be routed as shown. Cable must extend a minimum of24" from the rear
wall. For power cord connections, install a 3-prong grounding type receptacle in the sink cabinet rear wall, 6" min.
Or 16" max. From the opening, 6" to 16" above the floor.
3
Installation Instructions
PREPARE WATER LINE
The line may enter from either side, rear or floor within the shaded area.
The line may pass through the same hole as the eledtrical cable and drain hose. Or, cut an additional. Ifpower cord with cord with plug is used, water line must not pass through power cord hole.
f
/1
/ I I '
-----,1/ // ,
I "
/f' / ,
I ,
=====£t
~:~n"
o;~:
5"j- 4~"+5'~: ,4" ",
II
Shut-off. Hole
-I 1-- -,
~ Valve,.} ( -------- ~
HODI====c::r_-_-_, I
H I I
:: 2
----t------
I
From
Cabine
,
I,
19" From Wall
K
2" From Floor
Cabinet Face--
Figure 9
WATER LINE CONNECTION
Note to Consumer
Midea dishwasher could use both hot water and cold wate .
* Turn off the water supply. * We suggest you installing a hand shut-off valve in an
accessible location, such as under the sink.
* Water connection is on the left side of the dishwasher.
Install the hot water inlet line, using no less than 3/8" O.D. Copper tubing. Route the line as shown and extend forward at least 19" from rear wall.
* Flush water line to clean out debris. * The water pressure must be O.04~1 Mpa.
ADJUST DOOR BALANCE
Our company have adjusted door balance well. If you do not satisfy the tension of spring or after installing the door panel, you may adjust the spring
* if door drops open when released, increase spring
tension. If door closes when released, decrease tension.
Increase
,T
Spring
;- t~:::~~.
Spring
'Ienston
Figure 10
ADJUSTMENT
If door does not open easily or fall too quickly, you should adjust the tension of door spring. Pull out bolt and insert it into lower or higher hole, the spring
tension will be increase or decrease. If you do not
satisfy the tension still, repeat the process.
REMOVE TOEKICK
Remove the toe kick.
Figure 11
4
Installation Instructions
INSTALL POWER CORD
Skip this step if dishwasher will be direct wired or has a factory installed power cord.
The power cord and connections must comply with the National Electrical Code, Section 422 and/or local codes and ordinances.
Figure 12
A C
Remove Insert Power
Junction Box Cord Wires Thr
Cover Strain Relief
{D-~"d_::::~---i
B
Check That White, Black and
Green Dishwasher Wires Are Threaded
Thru Small Hole in Bracket
D
UseULListed
Wire Nuts
* Connect incoming power cord white (or ribbed) to
dishwasher white, black (or smooth) to black and Ground to dishwasher green wire. Use UL listed wire nuts of appropriate size.
* Replace j unction box cover. Be sure wires are not
pinched under the cover.
POSITION WATER LINE AND HOUSE WIRING
Position water supply line and house wiring on the floor ofthe opening to avoid interference with base of
dishwasher and components under dishwasher.
Figure 13
SLIDE DISHWASHER INTO CABINET
INSERT DRAIN HOSE AND
CONNECT WATER LINE
Upright the dishwasher and position in the front of opening. Insert drain hose into cabinet wall hole. If a power cord is used, guide the end through a separate hole.
Figure 14
Connect the water line of dishwasher into user water line.
DO NOT PUSH AGAINST FRONT PANEL WITH KNEES. DAMAGE WILL OCCUR. Slide dishwasher into the opening a few inches at a time.
Figure 15
As you proceed, pull the drain hose through the opening under the sink. Stop pushing when the dishwasher is a few inches forward of adjacent cabinetry.
Make sure drain hose is not kinked under the dishwasher and there is no interference with the water line and wiring or any other component.
5
I
Installation Instructions
LEVEL DISHWASHER
IMPORTANT-- Dishwasher must be level for proper dish rack operation and wash performance.
*
Place level on door and rack track inside the tub as
shown to check that the dishwasher is level.
*
Level the dishwasher by adjusting the four leveling.
* If adjustment to the right rear leveling leg is required,
loosen junction box bracket screw and rotate bracket clockwise.
Check
Level Front
to Back
t~k~~~~~~
Check Level
"'==..JT:c:--"\----j
\,rI
Side To Side
Turn Legs
to Adjust
Figure 16
Figure 15
POSITION DISHWASHER, SECURE TO CABINET
The dishwasher must be secured to the countertop or the cabinet sides. When countertops are made of wood use Method 1. Some models are supplied with side
mounting brackets for use when countertops are granite or other materials that will not accept screws. Use
Method 2 to secure dishwasher at the sides.
Method 1
Secure Dishwasher To Wood countertop
Position dishwasher so that the door lines up with the
front face of adjacent cabinet.
Brackets Wood Countertop
~
/
Figure 18
j j
~~~r
: : 3/4"
e e
Figure 17
IMPORTANT--Check to be sure the dishwasher is center ed in the opening and there is no interference with adjacent cabinets when opening or closing the door top with the 2 Phillips screws provided ..
* Position dishwasher so that the door lines up with the
front face of adjacent cabinet.
IMPORTANT: Check to be sure the dishwasher is centered in the opening and there is no interference with adjacent cabinets when opening or closing the door
6
Loading...
+ 17 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use