Magnavox DP-170-MS-8 Service manual

SERVICE MANUAL

DVD PLAYER

DP170MS8

STANDBY-ON PREV NEXTPLAY STOP OPEN/CLOSE

IMPORTANT SAFETY NOTICE

Proper service and repair is important to the safe, reliable operation of all
Funai Equipment. The service procedures recommended by Funai and
described in this service manual are effective methods of performing
service operations. Some of these service special tools should be used
when and as recommended.

It is important to note that this service manual contains various CAUTIONS
and NOTICES which should be carefully read in order to minimize the risk
of personal injury to service personnel. The possibility exists that improper
service methods may damage the equipment. It also is important to
understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE.
Funai could not possibly know, evaluate and advice the service trade of all
conceivable ways in which service might be done or of the possible
hazardous consequences of each way. Consequently, Funai has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a
service procedure or tool which is not recommended by Funai must first
use all precautions thoroughly so that neither his safety nor the safe
operation of the equipment will be jeopardized by the service method
selected.

TABLE OF CONTENTS

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-1

Laser Beam Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2-1

Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3-1

Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4-1

Cabinet Disassembly Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5-1

How to Initialize the DVD Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6-1

Firmware Renewal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7-1

Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8-1

Schematic Diagrams / CBA’s and Test Points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9-1

Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-10-1

Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11-1

System Control Timing Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12-1

IC Pin Function Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13-1

Lead Identifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14-1

Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15-1

Mechanical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-16-1

Electrical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17-1

HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC.

Manufactured under license from Dolby Laboratories. “Dolby” and the
double-D symbol are trademarks of Dolby Laboratories.

SPECIFICATIONS

Item Conditions Unit Nominal Limit

1. Video Output 75 Ω load Vpp 1.0 ± 0.1

2. Coaxial Digital Out 75 Ω load mVpp 500 ± 50

3. Audio (PCM)
3-1. Output Level 1 kHz, 0 dB Vrms 1.9
3-2. S/N dB 120
3-3. Freq. Response
DVD fs = 48 kHz, 20 Hz ~ 22 kHz dB ± 1.0
CD fs = 44.1 kHz, 20 Hz ~ 20 kHz dB ± 1.0
3-4. THD+N
DVD 1 kHz, 0 dB % 0.005
CD 1 kHz, 0 dB % 0.005

Notes:

1. All Items are measured without pre-emphasis unless otherwise specified.

2. Power supply: AC 120 V, 60 Hz

3. Load Impedance: 100 kΩ load (Audio Output)

4. Room Ambient: +25 °C

1-1-1 E6E71SP

LASER BEAM SAFETY PRECAUTIONS

This DVD player uses a pickup that emits a laser beam.

Do not look directly at the laser beam coming
from the pickup or allow it to strike against your
skin.

The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep
your eyes at least 30 cm away from the pickup lens when the diode is turned on. Do not look directly at the laser
beam.

CAUTION: Use of controls and adjustments, or doing procedures other than those specified herein, may result in
hazardous radiation exposure.

Drive Mechanism
Assembly

Laser Beam Radiation

Laser Pickup

Turntable

CAUTION

LASER RADIATION

WHEN OPEN. DO NOT

STARE INTO BEAM.

Location: Top of DVD mechanism.

1-2-1 E7NLSP

IMPORTANT SAFETY PRECAUTIONS

Product Safety Notice

Some electrical and mechanical parts have special
safety-related characteristics which are often not
evident from visual inspection, nor can the protection
they give necessarily be obtained by replacing them
with components rated for higher voltage, wattage,
etc. Parts that have special safety characteristics are
identified by a # on schematics and in parts lists. Use
of a substitute replacement that does not have the
same safety characteristics as the recommended
replacement part might create shock, fire, and/or other
hazards. The Product’s Safety is under review
continuously and new instructions are issued
whenever appropriate. Prior to shipment from the
factory, our products are carefully inspected to confirm
with the recognized product safety and electrical
codes of the countries in which they are to be sold.
However, in order to maintain such compliance, it is
equally important to implement the following
precautions when a set is being serviced.

Precautions during Servicing

A. Parts identified by the # symbol are critical for

safety. Replace only with part number specified.

B. In addition to safety, other parts and assemblies

are specified for conformance with regulations
applying to spurious radiation. These must also be
replaced only with specified replacements.
Examples: RF converters, RF cables, noise
blocking capacitors, and noise blocking filters, etc.

C. Use specified internal wiring. Note especially:

1) Wires covered with PVC tubing

2) Double insulated wires

3) High voltage leads

D. Use specified insulating materials for hazardous

live parts. Note especially:

1) Insulation tape

2) PVC tubing

3) Spacers

4) Insulators for transistors

E. When replacing AC primary side components

(transformers, power cord, etc.), wrap ends of
wires securely about the terminals before
soldering.

F. Observe that the wires do not contact heat

producing parts (heat sinks, oxide metal film
resistors, fusible resistors, etc.).

G. Check that replaced wires do not contact sharp

edges or pointed parts.

H. When a power cord has been replaced, check that

5 - 6 kg of force in any direction will not loosen it.

I. Also check areas surrounding repaired locations.
J. Be careful that foreign objects (screws, solder

droplets, etc.) do not remain inside the set.

K. When connecting or disconnecting the internal

connectors, first, disconnect the AC plug from the
AC outlet.

1-3-1 DVDN_ISP

Safety Check after Servicing

Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts, and
wires have been returned to their original positions. Afterwards, do the following tests and confirm the specified
values to verify compliance with safety standards.

1. Clearance Distance

When replacing primary circuit components, confirm
specified clearance distance (d) and (d’) between
soldered terminals, and between terminals and
surrounding metallic parts. (See Fig. 1)

Table 1: Ratings for selected area

Chassis or Secondary Conductor

Primary Circuit

AC Line Voltage Clearance Distance (d), (d’)

120 V ≥ 3.2 mm (0.126 inches)

Note: This table is unofficial and for reference only. Be

sure to confirm the precise values.

2. Leakage Current Test

Confirm the specified (or lower) leakage current
between B (earth ground, power cord plug prongs) and
externally exposed accessible parts (RF terminals,
antenna terminals, video and audio input and output
terminals, microphone jacks, earphone jacks, etc.) is
lower than or equal to the specified value in the table
below.

Measuring Method (Power ON):

Insert load Z between B (earth ground, power cord plug
prongs) and exposed accessible parts. Use an AC
voltmeter to measure across the terminals of load Z.
See Fig. 2 and the following table.

d' d

Fig. 1

Exposed Accessible Part

Z

AC Voltmeter
(High Impedance)

Earth Ground

B

Power Cord Plug Prongs

Table 2: Leakage current ratings for selected areas

AC Line Voltage Load Z Leakage Current (i) Earth Ground (B) to:

120 V

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

0.15 µF CAP. & 1.5 kΩ RES.
Connected in parallel

i ≤ 0.5 mA Peak Exposed accessible parts

1-3-2 DVDN_ISP

Fig. 2

STANDARD NOTES FOR SERVICING

Circuit Board Indications

1. The output pin of the 3 pin Regulator ICs is
indicated as shown.

Top View

Out

2. For other ICs, pin 1 and every fifth pin are
indicated as shown.

Pin 1

3. The 1st pin of every male connector is indicated as
shown.

Pin 1

Input

In

Bottom View

5

10

Pb (Lead) Free Solder

When soldering, be sure to use the Pb free solder.

How to Remove / Install Flat Pack-IC

1. Removal

With Hot-Air Flat Pack-IC Desoldering Machine:

1. Prepare the hot-air flat pack-IC desoldering
machine, then apply hot air to the Flat Pack-IC
(about 5 to 6 seconds). (Fig. S-1-1)

Fig. S-1-1

Instructions for Connectors

1. When you connect or disconnect the FFC (Flexible
Foil Connector) cable, be sure to first disconnect
the AC cord.

2. FFC (Flexible Foil Connector) cable should be
inserted parallel into the connector, not at an
angle.

FFC Cable

Connector

CBA

* Be careful to avoid a short circuit.

2. Remove the flat pack-IC with tweezers while
applying the hot air.

3. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)

4. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)

CAUTION:

1. The Flat Pack-IC shape may differ by models. Use
an appropriate hot-air flat pack-IC desoldering
machine, whose shape matches that of the Flat
Pack-IC.

2. Do not supply hot air to the chip parts around the
flat pack-IC for over 6 seconds because damage
to the chip parts may occur. Put masking tape
around the flat pack-IC to protect other parts from
damage. (Fig. S-1-2)

1-4-1 DVDN_SN

3. The flat pack-IC on the CBA is affixed with glue, so
be careful not to break or damage the foil of each
pin or the solder lands under the IC when
removing it.

With Soldering Iron:

1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder
flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)

CBA

Masking
Tape

Tweezers

Hot-air
Flat Pack-IC
Desoldering
Machine

Flat Pack-IC

Fig. S-1-2

Flat Pack-IC

Desoldering Braid

Soldering Iron

Fig. S-1-3

2. Lift each lead of the flat pack-IC upward one by
one, using a sharp pin or wire to which solder will
not adhere (iron wire). When heating the pins, use
a fine tip soldering iron or a hot air desoldering
machine. (Fig. S-1-4)

Sharp
Pin

Fine Tip
Soldering Iron

3. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)

4. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)

Fig. S-1-4

1-4-2 DVDN_SN

With Iron Wire:

1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder
flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)

2. Affix the wire to a workbench or solid mounting
point, as shown in Fig. S-1-5.

3. While heating the pins using a fine tip soldering
iron or hot air blower, pull up the wire as the solder
melts so as to lift the IC leads from the CBA
contact pads as shown in Fig. S-1-5.

4. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)

5. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)

Note: When using a soldering iron, care must be

taken to ensure that the flat pack-IC is not
being held by glue. When the flat pack-IC is
removed from the CBA, handle it gently
because it may be damaged if force is applied.

Hot Air Blower

2. Installation

1. Using desoldering braid, remove the solder from
the foil of each pin of the flat pack-IC on the CBA
so you can install a replacement flat pack-IC more
easily.

2. The “●” mark on the flat pack-IC indicates pin 1.
(See Fig. S-1-7.) Be sure this mark matches the 1
on the PCB when positioning for installation. Then
presolder the four corners of the flat pack-IC. (See
Fig. S-1-8.)

3. Solder all pins of the flat pack-IC. Be sure that
none of the pins have solder bridges.

Example :

Pin 1 of the Flat Pack-IC
is indicated by a " " mark.

Fig. S-1-7

To Solid
Mounting Point

CBA

Tweezers

Iron Wire

Soldering Iron

Fig. S-1-5

Fine Tip
Soldering Iron

Flat Pack-IC

or

Presolder

Flat Pack-IC

CBA

Fig. S-1-8

Fig. S-1-6

1-4-3 DVDN_SN

Instructions for Handling Semi­conductors

Electrostatic breakdown of the semi-conductors may
occur due to a potential difference caused by
electrostatic charge during unpacking or repair work.

1. Ground for Human Body

Be sure to wear a grounding band (1 MΩ) that is
properly grounded to remove any static electricity that
may be charged on the body.

2. Ground for Workbench

Be sure to place a conductive sheet or copper plate
with proper grounding (1 MΩ) on the workbench or
other surface, where the semi-conductors are to be
placed. Because the static electricity charge on
clothing will not escape through the body grounding
band, be careful to avoid contacting semi-conductors
with your clothing.

<Incorrect>

<Correct>

1MΩ

CBA

Grounding Band

1MΩ

CBA

Conductive Sheet or
Copper Plate

1-4-4 DVDN_SN

CABINET DISASSEMBLY INSTRUCTIONS

1. Disassembly Flowchart

This flowchart indicates the disassembly steps to gain
access to item(s) to be serviced. When reassembling,
follow the steps in reverse order. Bend, route, and
dress the cables as they were originally.

[1] Top Cover

[2] Front Unit

[5] Reinforce Plate

[7] DVD Main CBA Unit

[8] DVD Mechanism

[9] AV CBA

[10] Plate Holder

2. Disassembly Method

[3] Function CBA

[4] Front Assembly

[6] Rear Panel

[11] Main PCB Holder

ID/

Loc.

No.

[11]

↓

(1)

Note:

(1) Identification (location) No. of parts in the figures
(2) Name of the part
(3) Figure Number for reference
(4) Identification of parts to be removed, unhooked,

unlocked, released, unplugged, unclamped, or
desoldered.
P = Spring, L = Locking Tab, S = Screw,
CN = Connector
* = Unhook, Unlock, Release, Unplug, or Desolder
e.g. 2(S-2) = two Screws (S-2),
2(L-2) = two Locking Tabs (L-2)

(5) Refer to “Reference Notes.”

Part

Main PCB
Holder

↓

(2)

Fig.
No.

D8 (S-11) ---

↓

(3)

Removal

Remove/*Unhook/

Unlock/Release/

Unplug/Desolder

↓

(4)

Note

(5)

↓

ID/

Loc.

No.

[1] Top Cover D1 5(S-1) ---

[2] Front Unit D2

[3]

[4]

[5]

[6] Rear Panel D4 4(S-3), (S-4), (S-5) 4

[7]

[8]

[9] AV CBA D7 (S-8), (S-9) ---

Part

Function
CBA

Front
Assembly

Reinforce
Plate

DVD Main
CBA Unit

DVD
MechanismD5D6

Fig.

No.

D3 *3(L-4) ---

D3 ---------- ---

D4 2(S-2) ---

D5

*4(L-1), *2(L-2),
*3(L-3), *CN2001

(S-6), *CN201,
*CN301, *CN401,
*CN601

4(S-7)

Removal

Remove/*Unhook/

Unlock/Release/

Unplug/Desolder

Note

1

2
4

2
3

About tightening screws

When tightening screws, tighten them with the
following torque.

Screws Torque

(S-1), (S-2), (S-3), (S-4),
(S-5), (S-6), (S-7), (S-8),
(S-9), (S-10), (S-11)

0.45 ± 0.05 N·m

[10]

Plate
Holder

D8 (S-10) ---

1-5-1 E6E71DC

Reference Notes

1. CAUTION 1: Locking Tabs (L-1), (L-2) and (L-3)
are fragile. Be careful not to break them.

1) Release four Locking Tabs (L-1), then release

two Locking Tabs (L-2).

2) Release three Locking Tabs (L-3).

3) Disconnect connector CN2001, then remove

the Front Unit.

2. CAUTION 2: Electrostatic breakdown of the laser
diode in the optical system block may occur as a
potential difference caused by electrostatic charge
accumulated on cloth, human body etc., during
unpacking or repair work.
To avoid damage of pickup follow next procedures.

1) Short the three short lands of FPC cable with

solder before removing the FFC cable (CN201)
from it. If you disconnect the FFC cable
(CN201), the laser diode of pickup will be
destroyed. (Fig. D5)

2) Disconnect the Connectors (CN301), (CN401)

and (CN601). Remove screw (S-6) and lift the
DVD Main CBA Unit. (Fig. D5)

3. CAUTION 3: When reassembling, confirm the
FFC cable (CN201) is connected completely. Then
remove the solder from the three short lands of
FPC cable. (Fig. D5)

4. CAUTION 4: When installing the DVD Main CBA
Unit with a screw, hold and press the DVD Main
CBA Unit to align the HDMI connector with the
connector’s hole for HDMI on the Rear Panel.

(L-2)

(L-4)

(L-1)

(L-3)

(L-4)

[3] Tray Panel

CN2001

(L-1)

(L-2)

[2] Front Unit

Fig. D2

[3] Function CBA

[1] Top Cover

(S-1)

(S-1)

[4] Front Assembly

Fig. D3

(S-1)

Fig. D1

1-5-2 E6E71DC

[5] Reinforce
Plate

(S-2)

(S-2)

[6] Rear Panel

(S-5)

(S-3)

Fig. D4

(S-4)

(S-3)

(S-7)

(S-7)

[8] DVD
Mechanism

Fig. D6

[7] DVD Main CBA Unit

(S-6)

CN601

CN201

CN301

CN401

A

Short the three short lands by soldering.
(Either of two places.)

[9] AV CBA

(S-8)

(S-9)

Fig. D7

FPC Cable

View for A

Fig. D5

1-5-3 E6E71DC

(S-10)

[10] Plate Holder

(S-11)

[11] Main
PCB Holder

Fig. D8

3. How to Eject Manually

1. Turn the unit over.

2. Insert the shaft less than a diameter of 3 mm (e.g. screwdriver) straightly into the opening as shown.

3. Turn the shaft along with the opening clockwise.

4. Repeat steps 2 and 3 until the tray will open.

5. Pull the tray slowly manually

View for B

Rear

Turn the shaft along with
the opening clockwise.

Shaft
(e.g. screwdriver)

Opening

B

Front

1-5-4 E6E71DC

HOW TO INITIALIZE THE DVD PLAYER

To put the program back at the factory-default,
initialize the DVD player as the following procedure.

1. Press [1], [2], [3], [4], and [DISPLAY] buttons on
the remote control unit in that order.
Fig. a appears on the screen.

"

" differs depending on the models.

*******

MODEL : *******

Version
Region

: *.**

: *

EXIT: POWEREEPROM CLEAR : CLEAR

Fig. a

"

" differs depending on the models.

*******

2. Press [CLEAR] button on the remote control unit.
Fig. b appears on the screen.

MODEL : *******

Version
Region

: *.**

: *

EXIT: POWEREEPROM CLEAR : CLEAR

EEPROM CLEAR : OK

Fig. b

When “OK” appears on the screen, the factory
default will be set.

3. To exit this mode, press [STANDBY-ON] button.

1-6-1 E6E71NT

FIRMWARE RENEWAL MODE

1. Turn the power on and remove the disc on the tray.

2. To put the DVD player into version up mode, press
[9], [8], [7], [6], and [SEARCH] buttons on the
remote control unit in that order. The tray will open
automatically.
Fig. a appears on the screen and Fig. b appears
on the VFD.

"

" differs depending on the models.

*******

F/W Version Up Mode Model No : *******

Please insert a DISC

for F/W Version Up.

VERSION : *.**

EXIT: POWER

Fig. a Version Up Mode Screen

Fig. b VFD in Version Up Mode

The DVD player can also enter the version up
mode with the tray open. In this case, Fig. a will be
shown on the screen while the tray is open.

3. Load the disc for version up.

4. The DVD player enters the F/W version up mode
automatically. Fig. c appears on the screen and
Fig. d appears on the VFD. If you enter the F/W for
different models, “Disc Error” will appear on the
screen, then the tray will open automatically.

"

" differs depending on the models.

*******

(*1)

F/W Version Up Mode Model No : *******

VERSION : ************.***
Reading...

VERSION : *.**

The appearance shown in (*1) of Fig. c is
described as follows:

No. Appearance State

1 Reading... Sending files into the memory
2 Erasing... Erasing previous version data
3 Programming... Writing new version data

5. After programming is finished, the tray opens
automatically. Fig. e appears on the screen and
the checksum in (*2) of Fig. e appears on the VFD
(Fig. f).

"

" differs depending on the models.

*******

(*2)

F/W Version Up Mode

VERSION : ************.***
Completed

SUM : 7ABC

Model No : *******
VERSION : *.**

Fig. e Completed Program Mode Screen

Fig. f VFD upon Finishing the Programming Mode (Example)

At this time, no button is available.

6. Remove the disc on the tray.

7. Unplug the AC cord from the AC outlet. Then plug
it again.

8. Turn the power on by pressing the [STANDBY-ON]
button and the tray will close.

9. Press [1], [2], [3], [4], and [DISPLAY] buttons on
the remote control unit in that order.
Fig. g appears on the screen.

"

" differs depending on the models.

*******

Fig. c Programming Mode Screen

Fig. d VFD in Programming Mode (Example)

MODEL : *******

Version
Region

: *.**

: *

EXIT: POWEREEPROM CLEAR : CLEAR

Fig. g

1-7-1 E6E71FW

10. Press [CLEAR] button on the remote control unit.
Fig. h appears on the screen.

"

" differs depending on the models.

*******

MODEL : *******

Version
Region

: *.**

: *

EXIT: POWEREEPROM CLEAR : CLEAR

EEPROM CLEAR : OK

Fig. h

When “OK” appears on the screen, the factory
default will be set. Then the firmware renewal
mode is complete.

11. To exit this mode, press [STANDBY-ON] button.

1-7-2 E6E71FW

BLOCK DIAGRAMS

System Control / Servo Block Diagram

FIP

FL2001

SEGMENT

GRID

KEY

KEY-1 5

5

CN2001 CN2101

KEY-2 3

3

MATRIX

FUNCTION CBA

KEY-3 4

K2 1

KEY-4 6

K1 2

4

1

6

2

IC2001

IC101

(MICRO CONTROLLER)

(FRONT PANEL CONTROL)

~

789

23

17

~

7G

1G

a/KEY-1

IC462

+3.3V

IC461

+3.3V

1

b/KEY-2

c/KEY-3

RESET70

RESET

1 3

RESET

2 1

12

10

11

131416

i

f

g

h

e

d/KEY-4

FP-STB

FP-DOUT

FP-CLK

FP-DIN

2

1

27

28

CN1001

FP-STB 24

FP-DOUT 21

FP-CLK 23

FP-DIN 22

REMOTE 25

24

21

23

22

25

CN401

54

56

53

55

49

FP-DIN

FP-STB

FP-CLK

REMOTE

FP-DOUT

DRIVE

312

SPDL

66

-

+

-

+

SPINDLE

MOTOR

DRIVE

12

11

SLD

67

645

23

-

+

SLED

MOTOR

DRIVE

17

18

(OP AMP)

IC202

SP-ROT

121

14

13

12

VREF

(SERVO DRIVE)

IC301

FOCUS DRIVE

FD-OFST

127

124

26

25

27

-

+

-

+

FOCUS

ACTUATOR

DRIVE

15

16

24

TRACKING

TD-OFST

126

123

-

+

-

+

TRACKING

ACTUATOR

DRIVE

14

13

SL-ADS

122

8

10

3

4

K1

K2

V-SENSE

80

80

9

+3.3V

675

+5V

REMOTE

RM2001

AV CBA

SENSOR

TRAY-IN

64

DVD MAIN CBA UNIT

1 NOTE:

Either IC461 or IC462 is used for DVD MAIN CBA UNIT.

FS(+)

FS(-)

TO DIGITAL SIGNAL

TS(+)

TS(-)

PROCESS BLOCK

DIAGRAM

1-8-1

1SP(+)

2SP(-)

6TRAY-IN

3GND

4SL(-)

SLED

MOTOR

5SL(+)

M

CN301

DRIVE CBA

TRAY-IN

M

SPINDLE

MOTOR

E6E71BLS

Digital Signal Process Block Diagram

TO

VIDEO

/AUDIO

BLOCK

DIAGRAM

SPDIF

I2C-SCL

I/P-SW

AUDIO SIGNAL

VIDEO SIGNAL

I2C-SDA

AUDIO-MUTE

8

46

61

I/P-SW

I2C-SDA

AUDIO-MUTE

47

I2C-SCL

PCM-DATA0

152

PCM-BCK

PCM-LRCK

151

149

PCM-SCLK

150

148

AUDIO(L)

AUDIO(R)

146

AUDIO D/A

144

CONVERTER

VIDEO-C

VIDEO-Y(I/P)

131

139

C

Y(I/P)

D/A

D/A

TO

VIDEO-Cr/Pr

Cr/Pr

NTSC/PAL

ENCODER

VIDEO

129

D/A

/AUDIO

BLOCK

DIAGRAM

VIDEO-Cb/Pb

~

9

130

Cb/Pb

D/A

YC(0-7)

~

141718

IC103 (FLASH ROM)

~

293638

EXADT (0-15)

FLASH

ROM

~

~

~

1

9

45

162548

EADR (16-19)

DATA

RAM

DSP

DECODER

EXTERNAL

MEMORY

I/F

INST.

ROM

STREAM

I/F

DECODER

I/F

ECC

DATA

RAM

I/O

INST.

ROM

PROCESSOR

DMA

AUDIO

DVD/CD

FORMATTER

19

LATCH

9

EADR (0, 9-15) EADR (0-15)

~

12

D TYPE

IC104 (LATCH)

~

2

EXADT (0, 9-15)

19

LATCH

9

I/F

VIDEO

I/F

DATA

CACHE

UMAC

BCU

SERIAL

GENERAL

I/O

CPU

I/F

READ

MEMORY

INTERRUPT

32BIT

CONTROLLER

CPU

TIMER

WATCH DOG

TIMER

REMOTE

CONTROL

CPU

I/F

WATCH DOG

TIMER

TIMER

32BIT CPU

BCU

INST

CACHE

DEBUG

EXADT (0-15), EADR (16-19)

EADR (1-8)

~

12

D TYPE

IC105 (LATCH)

~

2

EXADT (0-15), EADR (16-19)

EXADT (1-8)

SDRAM ADDRESS(0-10)

IC101 (MICRO CONTROLLER)

~

194

209

SDRAM ADDRESS(0-10)

~~

222629

IC501 (SDRAM)

34

2

SDRAM

SDRAM DATA(0-15)

~

159

SDRAM DATA(0-15)

~

134253

178

INST.

ROM

DATA

RAM

INTERRUPT

5

9

GND(LD)

GND(CD-PD)

CONTROLLER

CD/DVD

79

GND(DVD-PD)

63

GND(CD-PD)

62

FS

TS

FS(+)

CN201

FS(+) 2

TO SYSTEM

CONTROL/SERVO

FS(-)

TS(+)

FS(-) 3

TS(+) 1

BLOCK DIAGRAM

TS(-)

TS(-) 4

DVD MAIN CBA UNIT

PICK-UP

UNIT

E6E71BLD

RF

SIGNAL

PROCESS

CIRCUIT

999897

100

115

116

113

114

~

CN201

C16

A17

B15

D18

CD/DVD 19

DETECTOR

106

104

AMP

Q251,Q252

Q253,Q254

AMP

CN201

CD-LD 10

DVD-LD 8

105

PD-MONI 7

103

6

GND(DVD-PD)

1-8-2

Video / Audio Block Diagram

VIDEO-Cb/Pb

OUT

VIDEO-Y

AUDIO SIGNAL

JK1404

JK1401

S-VIDEO OUT

VIDEO SIGNAL

43

2

1

YC

WF3

13

14

DRIVER

2dB

AMP

2dB

VIDEO OUT

(COMPOSITE)

15

AMP

2dB

AMP

OUT

2dB

11

AMP

VIDEO-Cr/Pr

OUT

10

2dB

AMP

5

DIGITAL

JK1202

AMP

Q1351

AUDIO OUT

(COAXIAL)

(AMP)

IC1201

+9V

JK1404

167

3

AUDIO(L)-

OUT

2

AUDIO(R)-

OUT

Q1201

5

Q1202

+3.3V

Q1204

CNF01

SWITCHING

QF01, QF03

ICF04

(3.3V<-->5V CONVERTER)

119

HPD

HDMI-CONNECTOR

DDC

HOT PLUG

DETECT

6

5

2

3

120

121

I/F

SCL

151916

TMDS DATA2+

TMDS DATA1-

TMDS DATA1+

TMDS DATA0-

TMDS DATA0+

TMDS CLOCK+

7

10

12

16

TMDS CLOCK-

12

10

TMDS DATA2-

SDA

649

3

1

182014

22

24

TMDS

TRANSMITTER

TMDS

ENCODER

IC1402 (VIDEO DRIVER)

WF1

DVD MAIN CBA UNIT AV CBA

LPF DRIVER

4dB

AMP

3

LPF DRIVER

4dB

AMP

1

WF2

CN1601

88VIDEO-Y(I/P)

10 10VIDEO-C

CN601

VIDEO-Y(I/P)

VIDEO-C

TO DIGITAL

SIGNAL PROCESS

LPF DRIVER

4dB

AMP

6

66VIDEO-Cb/Pb

44VIDEO-Cr/Pr

VIDEO-Cb/Pb

VIDEO-Cr/Pr

BLOCK DIAGRAM

LPF DRIVER

4dB

AMP

8

WF6

CN601 CN1601

WF4

3

I/P-SW
3

SPDIF

I/P-SW

16

SPDIF

16

AUDIO(L)

TO DIGITAL

14

AUDIO(R)

12 12AUDIO(L)

14

AUDIO(R)

AUDIO-MUTE

SIGNAL PROCESS

BLOCK DIAGRAM

WF5

13 13AUDIO-MUTE

ICF09 (HDMI INTERFACE)

IIC

I/F

113

114

I2C-SCL

I2C-SDA

AUDIO

I/F

33

38

43

PCM-SCLK

PCM-LRCK

PCM-DATA0

TO DIGITAL

SIGNAL PROCESS

HDCP

CIPHER/

ENCRYPTOR

AV

CONTROLLER

41

45

PCM-BCK

BLOCK DIAGRAM

VIDEO

I/F

~

81

83~86

90

YC(0-7)

1-8-3

E6E71BLV

Power Supply Block Diagram

NOTE:

The voltage for parts in hot circuit is measured using

hot GND as a common terminal.

EV+1.2V

TO CN401

4,5

CN1001

EV+3.3V

6,7,8

EV+10V10P-ON+5V9P-ON+3.3V20PWRCON

11,12

"Ce symbole reprèsente un fusible à fusion rapide."

"This symbol means fast operating fuse."

CAUTION !

For continued protection against fire hazard,

replace only with the same type fuse.

ATTENTION : Pour une protection continue les risqes

d'Incele n'utiliser que des fusible de même type.

Risk of fire-replace fuse as marked.

D1003

F

A V

T1001

-FL

F1

F2

IC1002

RECTIFIER

D1008

11

2

EV+5V

P-ON+9V

EV+3.3V

+1.2V REG.

SCHOTTKY

BARRIER

D1030

12

P-ON+5V

SCHOTTKY

BARRIER

131514

4

SW+10V

Q1002

D1009

RECTIFIER

SW+3.3V

Q1011

SW+5V

Q1004

16

SWITCHING

Q1006,Q1007

D1016

RECTIFIER

17

6

18

7

SWITCHING

Q1005

IC1001

ERROR

VOLTAGE DET

SWITCHING

Q1015

1

4

SWITCHING

Q1016

2

3

312

REG

IC1006

(SHUNT REGULATOR)

CAUTION !

Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.

If Main Fuse (F1001) is blown , check to see that all components in the power supply

circuit are not defective before you connect the AC plug to the AC power supply.

Otherwise it may cause some components in the power supply circuit to fail.

BRIDGE

RECTIFIER

D1001, D1002

D1004, D1005

LINE

FILTER

L1001

1A 250V

HOT CIRCUIT. BE CAREFUL.

F1001

AC1001

AC CORD

F

SWITCHING

Q1031

SWITCHING

Q1003

A V

CONTROL

1-8-4

Q1008

AV CBA

HOT

LATCH

E6E71BLP

SCHEMATIC DIAGRAMS / CBA’S AND TEST POINTS

Standard Notes

WARNING

Many electrical and mechanical parts in this chassis
have special characteristics. These characteristics
often pass unnoticed and the protection afforded by
them cannot necessarily be obtained by using
replacement components rated for higher voltage,
wattage, etc. Replacement parts that have these
special safety characteristics are identified in this
manual and its supplements; electrical components
having such features are identified by the mark “#” in
the schematic diagram and the parts list. Before
replacing any of these components, read the parts list
in this manual carefully. The use of substitute
replacement parts that do not have the same safety
characteristics as specified in the parts list may create
shock, fire, or other hazards.

Notes:

1. Do not use the part number shown on these
drawings for ordering. The correct part number is
shown in the parts list, and may be slightly
different or amended since these drawings were
prepared.

2. All resistance values are indicated in ohms
(K = 10

3. Resistor wattages are 1/4W or 1/6W unless
otherwise specified.

4. All capacitance values are indicated in µF
(P = 10

5. All voltages are DC voltages unless otherwise
specified.

3

, M = 106).

-6

µF).

1-9-1 E8N_SC

LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON
THE FOLLOWING PAGES:

1. CAUTION:

FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE

F

A V

SAME TYPE FUSE.
ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQES D'INCELE N'UTILISER
QUE DES FUSIBLE DE MÊME TYPE.
RISK OF FIRE-REPLACE FUSE AS MARKED.

This symbol means fast operating fuse.
Ce symbole represente un fusible a fusion rapide.

2. CAUTION:

Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F1001) is blown, first check to see that all components in the power supply circuit are not
defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components
in the power supply circuit to fail.

3. Note:

1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.

2. To maintain original function and reliability of repaired units, use only original replacement parts which are
listed with their part numbers in the parts list section of the service manual.

4. Voltage indications for PLAY and STOP mode on the schematics are as shown below:

2

1

(Unit: Volt)

The same voltage for
both PLAY & STOP modes

5.0

3

5.0
(2.5)

Indicates that the voltage
is not consistent here.

PLAY mode
STOP mode

5. How to read converged lines

1-D3
Distinction Area

Line Number
(1 to 3 digits)

Examples:

1. "1-D3" means that line number "1" goes to the line number
"1" of the area "D3".

2. "1-B1" means that line number "1" goes to the line number
"1" of the area "B1".

3

AREA D3

2

1

ABCD

AREA B1

1-D3

1-B1

6. Test Point Information

: Indicates a test point with a jumper wire across a hole in the PCB.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.

1-9-2 E8N_SC

DVD Main 1/4 Schematic Diagram

1 NOTE:
Either IC461 or IC462 is used for DVD MAIN CBA UNIT.

1-9-3

E6E71SCD1

DVD Main 2/4 Schematic Diagram

1-9-4

E6E71SCD2

DVD Main 3/4 Schematic Diagram

1-9-5

E6E71SCD3

DVD Main 4/4 Schematic Diagram

1-9-6

E6E71SCD4

AV 1/3 Schematic Diagram

"Ce symbole reprèsente un fusible à fusion rapide."

CAUTION !

For continued protection against fire hazard,
replace only with the same type fuse.
ATTENTION : Pour une protection continue les risqes
d'Incele n'utiliser que des fusible de même type.
Risk of fire-replace fuse as marked.

"This symbol means fast operating fuse."

A V

F

CAUTION !

Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F1001) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.

NOTE:

The voltage for parts in hot circuit is measured using
hot GND as a common terminal.

1-9-7

E6E71SCAV1

AV 2/3 Schematic Diagram

1-9-8

E6E71SCAV2

AV 3/3 & Function Schematic Diagram

7G

6G

REPEAT

A
ALL

TITLE

B

i

f

i

5G 4G 3G 2G 1G

CHP

REC
TRK

c

VCR

GROUP

a

b

d

ef

g

HDVCD

SACD

PSCAN

DVD

A

PM

FL2001 MATRIX CHART

7G 6G 5G 4G 3G 2G 1G

a

b

REPEAT

c

A

d

B

e

ALL

f

g

h

ii

a

b

c

d

e

ff

g

GROUP

TITLE

a

b

c

d

e

f

g

VCR

a

b

c

d

e

f

g

a

b

c

d

e

f

g

CHP

a

b

c

d

e

f

g

TRK

REC

SACD

PSCAN

DVD

A
P

M

HD

V

CD

1-9-9

E6E71SCAV3

AV CBA Top View

"Ce symbole reprèsente un fusible à fusion rapide."

CAUTION !

For continued protection against fire hazard,
replace only with the same type fuse.
ATTENTION : Pour une protection continue les risqes
d'Incele n'utiliser que des fusible de même type.
Risk of fire-replace fuse as marked.

"This symbol means fast operating fuse."

A V

F

CAUTION !

Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F1001) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.

NOTE:

The voltage for parts in hot circuit is measured using
hot GND as a common terminal.

Because a hot chassis ground is present in the power
supply circut, an isolation transformer must be used.
Also, in order to have the ability to increase the input
slowly, when troubleshooting this type power supply
circuit, a variable isolation transformer is required.

1-9-10

BE6E20F01012-A

AV CBA Bottom View

NOTE:

The voltage for parts in hot circuit is measured using
hot GND as a common terminal.

"Ce symbole reprèsente un fusible à fusion rapide."

CAUTION !

For continued protection against fire hazard,
replace only with the same type fuse.
ATTENTION : Pour une protection continue les risqes
d'Incele n'utiliser que des fusible de même type.
Risk of fire-replace fuse as marked.

"This symbol means fast operating fuse."

A V

F

CAUTION !

Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F1001) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.

Because a hot chassis ground is present in the power
supply circut, an isolation transformer must be used.
Also, in order to have the ability to increase the input
slowly, when troubleshooting this type power supply
circuit, a variable isolation transformer is required.

WF3

C1402
PLUS LEAD

WF1

PIN 8 OF
CN1601

WF2

PIN 10 OF
CN1601

WF4

PIN 12 OF
CN1601

WF5

PIN 14 OF
CN1601

WF6

PIN 16 OF
CN1601

1-9-11

BE6E20F01012-A

Function CBA Top View

Function CBA Bottom View

1-9-12

BE6E20F01012-B

WAVEFORMS

WF1

Pin 8 of CN1601

WF2

Pin 10 of CN1601

WF5

Pin 14 of CN1601

20µs0.2VVIDEO-Y

AUDIO(R) 0.5V 0.5ms

WF6

Pin 16 of CN1601

VIDEO-C 0.2V 20

WF3

C1402 PLUS LEAD

VIDEO-CVBS 0.5V 20

WF4

Pin 12 of CN1601

µ

s

SPDIF 1V 0.1

µ

s

NOTE:

Input
DVD: COLOR BAR SIGNAL (WITH 1KHz AUDIO SIGNAL)

µ

s

(WF1~WF6)

AUDIO(L) 0.5V 0.5ms

1-10-1

E8NWF

AC CORD

FUNCTION CBA

K2 11K1 22KEY-2 33KEY-3 44KEY-1 55KEY-4 6

CN2001 CN2101

CN2101 is soldered

directly to the PCB.

6

WIRING DIAGRAM

CN601

CN201CN301

GND(DVD-PD)
GND(CD-PD)

I/P-SW 33
VIDEO-Cr/Pr 44
GND 55
VIDEO-Cb/Pb 66
GND 77
VIDEO-Y(I/P) 88
GND 99
VIDEO-C 1010
AUDIO-GND 1111

CN1601

AUDIO(L) 1212
AUDIO-MUTE 1313
AUDIO(R) 1414
AUDIO-GND 1515
SPDIF 1616

(CN1601 is soldered directly to the PCB.)

P-ON+5V

CD/DVD

VREF

GND

CD-LD

GND(LD)

DVD-LD

PD-MONI

TS(-)

FS(-)
FS(+)
TS(+)

20
19

D

18

A

17

C

16

B

15

NU

14
13

NU

12
11
10

9
8
7
6
5
4
3
2
1

HDMI-CONNECTOR

4

DETECTOR

7 9 11 2 3 6 5

FS

TS

DIGITAL

AUDIO OUT

(COAXIAL)

S-VIDEO

OUT

AUDIO(R)-

OUT

AUDIO(L)-

OUT

VIDEO OUT

(COMPOSITE)

VIDEO-Cr/Pr

OUT

VIDEO-Cb/Pb

OUT

VIDEO-Y

OUT

AV CBA

EV+1.2V 4

4

EV+1.2V 5

5

EV+3.3V 6

6

EV+3.3V 7

7

EV+3.3V 8

8

P-ON+3.3V 9

9

P-ON+5V 10

10

EV+10V 11

11

EV+10V 12

12

GND 13

13

GND 14

14

CN1001

GND 15

15

GND 16

16

GND 17

17

GND 18

18

GND 19

19

(CN1001 is soldered directly to the PCB.)

PWRCON 20

20

FP-DOUT 21

21

FP-DIN 22

22

FP-CLK 23

23

FP-STB 24

24

REMOTE

25

CN401

25

DVD MAIN CBA UNIT

TRAY-IN

6

SL(+)

5

SL(-)

4

GND

3

SP(-)

2

SP(+)

1

M

SLED

MOTORMSPINDLE

DVD MECHANISM

MOTOR

DRIVE CBA PICK UP UNIT

TRAY-IN

1-11-1

E6E71WI

SYSTEM CONTROL TIMING CHARTS

Tray Close ~ Play / Play ~ Tray Open

Tray IN
(TL221)

Sled Drive
(TP303)

Disc Drive
(TP301)

Focus Drive
(TP304)

Tracking Drive
(TP302)

3.3V

0V

1.65V

0V

1.65V

0V

1.65V

0V

1.65V

Tr ay
Close

Disc
Rotation

Play

Disc
Stop

Tr ay
Open

0V

1-12-1 E8NTI

IC PIN FUNCTION DESCRIPTIONS

IC2001 (FRONT PANEL CONTROL)

Pin

IN/

No.

OUT

1 IN FP-CLK Clock Input
2 IN FP-STB Serial Interface Strobe
3 IN K1 Key Data 1 Input
4 IN K2 Key Data 2 Input
5-VSS GND
6 - VDD Power Supply

7OUTa / KEY-1

8OUTb / KEY-2

9 OUT c / KEY-3

10 OUT d / KEY-4

11
12 f

OUT

13 g
14 h
15 - VEE Pull Down Level
16 OUT i Segment Output
17
18 6G
19 5G

OUT

20 4G
21 3G
22 2G
23 1G
24 - VDD Power Supply
25 - VSS GND
26 IN OSC Oscillator Input
27 OUT FP-DOUT Serial Data Output
28 IN FP-DIN Serial Data Input

Signal

e

7G

Name

Function

Segment Output / Key
Source-1

Segment Output / Key
Source-2

Segment Output / Key
Source-3

Segment Output / Key
Source-4

Segment Output

Grid Output

1-13-1 E6E71PIN

LEAD IDENTIFICATIONS

E

CB

KIA4558P/P

8

KTA1266-Y-AT/P
KTC3203-Y-AT/P

5

E

CB

MM1637XVBE

16

KTA1267-Y-AT/P
KTC3199-GR-AT/P
KTC3205-Y-AT/P
KRA110M-AT/P
KRC103M-AT/P

9

2SK3498

GDS

PT6313-S-TP(L)

28

15

1

TL432A-TA

123

1: R
2: A
3: K

4

PS2561A-1(W)

1

2

1: A
2: K
3: E
4: C

1

4
3

8

UTC1117YA

123

1: GND
2: Vout
3: Vin

1

Note:

A: Anode
K: Cathode
E: Emitter
C: Collector
B: Base
R: Reference
G: Gate
D: Drain
S: Source

14

1-14-1 E6E71LE

Cabinet

EXPLODED VIEWS

2L081

2L021

2B38

Function CBA

See Electrical Parts List
for parts with this mark.

Some Ref. Numbers are
not in sequence.

2L011

2L021

2L021

2B5

2L051

2L081

2L021

1B1

DVD Main CBA Unit

2L105

2L031

2L051

2L011

A21

A16

JK1202

JK1401

2B1

A22

A17

JK1404

AV CBA

2L071

2L011

F1001

AC1001

2L032

2L041
2L044

2L011

2L011

2L041

A23

A1X

2B3

A13

A15

A29

A13

1-15-1 E6E71CEX

Packing

X1

S2

X10

X9

S4

X5

X2

X4

S2

Unit

A22

S1

1-15-2 E6E71PEX

MECHANICAL PARTS LIST

PRODUCT SAFETY NOTE: Products marked with a

# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.

NOTE: Parts that are not assigned part numbers
(---------) are not available.

Ref. No. Description Part No.

A1X FRONT ASSEMBLY E6E71UD 1VM222881
A13 FOOT(REAR) E5710UD 0VM415007
A15 CHASSIS E5932UD 0VM101372
A16 TOP COVER(BLACK) E6A36UD 1VM322548
A17 REAR PANEL E6E71UD 1VM222896
A21 MODEL NO.LABEL(U) E6E71UD ---------­A22 LABEL BAR CODE E5900UD ---------­A23 TELEPHONE NO. LABEL H9670UD ---------­A29 LABEL EAS L0951UB ---------­1B1 DVD MECHA E7 HDMi N79F1KVM N79F1KVM
2B3 MAIN PCB HOLDER E5932UD 0VM204593D
2B5 REINFORCE PLATE E6A60UD 1VM321919
2B38 PLATE HOLDER E6A35UD 1VM322595
2L011 SCREW TAP TIGHT M3X5 BIND HEAD+BLK NI GBHC3050
2L021 SCREW S-TIGHT M3X10 BIND HEAD+ GBJS3100
2L031 SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080
2L032 SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060
2L041 SCREW B-TIGHT M3X8 BIND HEAD+ GBHB3080
2L044 S-TIGHT SCREW M3X6 BIND HEAD+BLACK GBHS3060
2L051 SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060
2L071 SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060
2L081 SCREW TAP TIGHT WASHER+ P-TIGHT GCJP3080
2L105 SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080

PACKING

S1 GIFT BOX CARTON E6E71UD 1VM323727
S2 SIDE PAD E6E71UD 1VM121072
S4 UNIT BAG E5500UD 0VM411683

ACCESSORIES

X1 REMOTE CONTROL UNIT NA474UD NA474UD
X2 DRY BATTERY R03/2S XB0M451T0006
X4 ACCESSORY BAG E5700UD 0VM415576
X5 AV CORD 1000/BLACK WPZ0102TM018
X9 HDMI CABLE 1800MM BLACK WPZ0182TSN01
X10# OWNERS MANUAL E6E71UD 1VMN23457

20070307 1-16-1 E6E71CA

ELECTRICAL PARTS LIST

PRODUCT SAFETY NOTE: Products marked with a

# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.

NOTES:

1. Parts that are not assigned part numbers (---------)
are not available.

2. Tolerance of Capacitors and Resistors are noted
with the following symbols.

C.....±0.25% D.....±0.5% F.....±1%

G.....±2% J......±5% K.....±10%

M.....±20% N.....±30% Z.....+80/-20%

DVD MAIN CBA UNIT

Ref. No. Description Part No.

DVD MAIN CBA UNIT N7CFPKUP

AV ASSEMBLY

Ref. No. Description Part No.

AV ASSEMBLY
Consists of the following:

AV C BA
FUNCTION CBA

AV CBA

Ref. No. Description Part No.

AV C BA
Consists of the following:

CAPACITORS

C1001# ACROSS THE LINE CAP. 0.068µF/250V CT2E683DC016
C1003 ELECTROLYTIC CAPACITOR

C1004 ELECTROLYTIC CAPACITOR

C1005 CERAMIC CAP. B K 120pF/500V CCD2JKP0B121
C1006# SAFETY CAP. 2200pF/250V CCD2EMA0E222
C1007 ELECTROLYTIC CAP. 3300µF/6.3V CE0KMASDL332
C1009 ELECTROLYTIC CAP. 1000µF/6.3V M CE0KMASDL102
C1010 CERAMIC CAP.(AX) CH J 680pF/50V CA1J681TU008
C1013 POLYESTER FILM CAP. (PB FREE) 0.0033µF/

C1017 CERAMIC CAP.(AX) Y M 0.01µF/16V CCA1CMT0Y103
C1018 ELECTROLYTIC CAP. 100µF/6.3V M CE0KMASDL101
C1021 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C1022 CHIP CERAMIC CAP.(1608) B K 0.022µF/50V CHD1JK30B223
C1029 CERAMIC CAP.(AX) X K 2200pF/16V CCA1CKT0X222
C1032 ELECTROLYTIC CAP. 10µF/16V M CE1CMASDL100
C1033 FILM CAP.(P) 0.022µF/50V J CA1J223MS029
C1034 ELECTROLYTIC CAP. 470µF/6.3V M CE0KMASDL471
C1035 ELECTROLYTIC CAP. 1000µF/16V M CE1CMASDL102
C1037 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C1038 ELECTROLYTIC CAP. 1000µF/6.3V M CE0KMASDL102
C1039 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104

ZT250TA2R2M6BB

ZR200TA820M12BB

100V J

1VSA15409

----------

----------

----------

CA2E2R2DYG02

CA2D820DYG01

CA2A332DT018

Ref. No. Description Part No.

C1047 POLYESTER FILM CAP. (PB FREE) 0.022µF/

C1048 ELECTROLYTIC CAP. 220µF/16V M CE1CMASDL221
C1049 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C1050 ELECTROLYTIC CAP. 1000µF/10V M CE1AMASDL102
C1051 ELECTROLYTIC CAP. 220µF/10V M CE1AMASDL221
C1053 ELECTROLYTIC CAP. 22µF/10V M CE1AMASDL220
C1201 ELECTROLYTIC CAP. 10µF/16V M CE1CMASDL100
C1202 ELECTROLYTIC CAP. 10µF/16V M CE1CMASDL100
C1205 CHIP CERAMIC CAP. CH J 220pF/50V CHD1JJ3CH221
C1206 CHIP CERAMIC CAP. CH J 220pF/50V CHD1JJ3CH221
C1207 CHIP CERAMIC CAP.(1608) CH J 68pF/50V CHD1JJ3CH680
C1208 CHIP CERAMIC CAP.(1608) CH J 68pF/50V CHD1JJ3CH680
C1221 ELECTROLYTIC CAP. 10µF/16V M H7 CE1CMASSL100
C1222 ELECTROLYTIC CAP. 10µF/16V M CE1CMASDL100
C1223 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C1224 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C1245 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C1246 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C1247 ELECTROLYTIC CAP. 470µF/6.3V M CE0KMASDL471
C1249 ELECTROLYTIC CAP. 47µF/16V M H7 CE1CMASSL470
C1351 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
C1352 ELECTROLYTIC CAP. 47µF/6.3V M H7 CE0KMASSL470
C1359 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C1360 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C1394 ELECTROLYTIC CAP. 47µF/16V M CE1CMASDL470
C1395 ELECTROLYTIC CAP. 1000µF/6.3V M CE0KMASDL102
C1398 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C1402 ELECTROLYTIC CAP. 470µF/6.3V M CE0KMASDL471
C1421 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C1422 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
C1441 CHIP CERAMIC CAP.(1608) B K 1µF/10V CHD1AK30B105
C1442 ELECTROLYTIC CAP. 1000µF/6.3V M CE0KMASDL102
C1461 CHIP CERAMIC CAP.(1608) B K 1µF/10V CHD1AK30B105
C1462 ELECTROLYTIC CAP. 220µF/6.3V M CE0KMASDL221
C1481 CHIP CERAMIC CAP.(1608) B K 1µF/10V CHD1AK30B105
C1482 ELECTROLYTIC CAP. 220µF/6.3V M CE0KMASDL221
C1522 ELECTROLYTIC CAP. 10µF/16V M CE1CMASDL100
C1524 ELECTROLYTIC CAP. 100µF/10V M CE1AMASDL101
C1531 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C1532 ELECTROLYTIC CAP. 22µF/6.3V M CE0KMASDL220
C1533 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C1534 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C1537 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C2001 ELECTROLYTIC CAP. 22µF/50V M CE1JMASDL220
C2002 ELECTROLYTIC CAP. 22µF/50V M CE1JMASDL220
C2003 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C2004 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C2031 ELECTROLYTIC CAP. 100µF/10V M CE1AMASDL101
C2032 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C2647 CERAMIC CAP.(AX) CH J 680pF/50V CA1J681TU008

100V J

CA2A223DT018

CONNECTORS

CN1001 WIRE ASSEMBLY FFC 22P 22P/90MM/WHITE WX1E6E71-022
CN1601 WIRE ASSEMBLY FFC 14P 14P/110MM/WHITE WX1E6E71-014
CN2001 FFC CONNECTOR IMSA-9615S-06A-PP-A JC96J06ER007

DIODES

D1001 RECTIFIER DIODE 1N4005 NDQZ001N4005
D1002 RECTIFIER DIODE 1N4005 NDQZ001N4005
D1003 RECTIFIER DIODE BA157 NDQZ000BA157
D1004 RECTIFIER DIODE 1N4005 NDQZ001N4005

20070307 1-17-1 E6E71EL

Ref. No. Description Part No.

D1005 RECTIFIER DIODE 1N4005 NDQZ001N4005
D1007 ZENER DIODE MTZJT-7722B QDTB00MTZJ22
D1008 SCHOTTKY BARRIER DIODE SB340 NDQZ000SB340
D1009 RECTIFIER DIODE FR202-B/P NDQZ000FR202
D1011 RECTIFIER DIODE BA157 NDQZ000BA157
D1012 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1016 RECTIFIER DIODE BA157 NDQZ000BA157
D1017 ZENER DIODE MTZJT-7718B QDTB00MTZJ18
D1018 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1022 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1024 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1025 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1030 RECTIFIER DIODE FR202-B/P NDQZ000FR202
D1046 ZENER DIODE MTZJT-775.6C QDTC0MTZJ5R6
D1047 ZENER DIODE MTZJT-775.1B QDTB0MTZJ5R1
D1048 ZENER DIODE MTZJT-7713B QDTB00MTZJ13
D1049 ZENER DIODE MTZJT-778.2A QDTA0MTZJ8R2
D1053 PCB JUMPER D0.6-P10.0 JW10.0T
D1054 PCB JUMPER D0.6-P10.0 JW10.0T
D1055 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1056 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1057 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1058 PCB JUMPER D0.6-P10.0 JW10.0T
D1059 PCB JUMPER D0.6-P10.0 JW10.0T
D1060 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1073 PCB JUMPER D0.6-P5.0 JW5.0T
D1301 ZENER DIODE MTZJT-775.6A QDTA0MTZJ5R6
D2041 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D2042 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D2043 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D2044 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133

ICS

IC1001# PHOTOCOUPLER PS2561A-1(W) QPEWPS2561A1
IC1002 IC VOLTAGE REGULATOR UTC1117YA NSZBA0T2H002
IC1006 SHUNT REGULATOR TL432A-TA NSZBA0T2T002
IC1201 IC OP AMP KIA4558P/P NSZBA0SJY035
IC1402 DRIVER FOR DVD MM1637XVBE QSZBA0TMM102
IC2001 VFD DRIVER/CONTROLLER IC PT6313-S-

TP(L)

NSZBA0TG2007

COILS

L1001# LINE FILTER 20MH 3905 LLBG00ZKT008
L1007 CHOKE COIL ELC10D220EM LLC220KMS003
L1009 RADIAL TYPE CHOKE COIL CW68-470K-

L1010 RADIAL TYPE CHOKE COIL CW68-470K-

L1350 INDUCTOR(100µH K) LAP02TA101K LLAXKATTU101
L1351 INDUCTOR(0.47µH K) LAP02TAR47K LLAXKATTUR47
L1521 PCB JUMPER D0.6-P5.0 JW5.0T
L1522 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
L2031 INDUCTOR(100µH K) LAP02TA101K LLAXKATTU101

841040NP

841040NP

LLBD00PKV023

LLBD00PKV023

TRANSISTORS

Q1002 TRANSISTOR KTA1267-Y-AT/P NQSYKTA1267P
Q1003 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q1004 TRANSISTOR KTC3203-Y-AT/P NQSYKTC3203P
Q1005 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q1006 TRANSISTOR KTA1267-Y-AT/P NQSYKTA1267P
Q1007 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q1008 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q1011 TRANSISTOR KTC3205-Y-AT/P NQSYKTC3205P
Q1015 TRANSISTOR KRA110M-AT/P NQSZKRA110MP
Q1016 NPN TRANSISTOR KRC103M-AT/P NQSZKRC103MP
Q1031# FET 2SK3498(T6L1FUNANQ QF1Z02SK3498

Ref. No. Description Part No.

Q1201 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q1202 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q1204 TRANSISTOR KTA1266-Y-AT/P NQSYKTA1266P
Q1351 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q1352 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P

RESISTORS

R1002 CARBON RES. 1/4W J 330 Ω RCX4JATZ0331
R1004 METAL OXIDE FILM RES. 1W J 100k Ω RN01104ZU001
R1005 CARBON RES. 1/4W J 2.7M Ω RCX4JATZ0275
R1006 CARBON RES. 1/4W J 2.7M Ω RCX4JATZ0275
R1008 CARBON RES. 1/4W J 620 Ω RCX4JATZ0621
R1009 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R1010 CARBON RES. 1/6W J 15k Ω RCX6JATZ0153
R1011 METAL OXIDE FILM RES. 1W J 1.2 Ω RN011R2ZU001
R1015 CARBON RES. 1/6W J 560 Ω RCX6JATZ0561
R1016 CARBON RES. 1/6W J 22k Ω RCX6JATZ0223
R1019 CHIP RES. 1/10W F 1.5k Ω RRXAFR5H1501
R1020 CARBON RES. 1/4W J 1.2k Ω RCX4JATZ0122
R1021 CHIP RES. 1/10W J 2.7k Ω RRXAJR5Z0272
R1022 CHIP RES. 1/10W J 820 Ω RRXAJR5Z0821
R1023 CHIP RES. 1/10W F 1.0k Ω RRXAFR5H1001
R1025 CHIP RES. 1/10W J 15k Ω RRXAJR5Z0153
R1029 CARBON RES. 1/6W J 470k Ω RCX6JATZ0474
R1032 CARBON RES. 1/6W J 3.3k Ω RCX6JATZ0332
R1034 CARBON RES. 1/6W J 390k Ω RCX6JATZ0394
R1035 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102
R1036 CARBON RES. 1/6W J 100k Ω RCX6JATZ0104
R1037 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R1038 CARBON RES. 1/6W J 100k Ω RCX6JATZ0104
R1039 CARBON RES. 1/6W J 470k Ω RCX6JATZ0474
R1043 METAL OXIDE FILM RES. 1W J 3.3 Ω RN013R3ZU001
R1044 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R1051 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R1052 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R1054 CHIP RES. 1/10W J 560 Ω RRXAJR5Z0561
R1059 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R1061 CARBON RES. 1/4W J 1.2k Ω RCX4JATZ0122
R1062 CARBON RES. 1/4W J 1.2k Ω RCX4JATZ0122
R1067 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R1068 CHIP RES. 1/10W J 330 Ω RRXAJR5Z0331
R1069 CARBON RES. 1/6W J 82 Ω RCX6JATZ0820
R1072 CHIP RES. 1/10W J 330 Ω RRXAJR5Z0331
R1073 METAL OXIDE FILM RES. 2W J 1.2 Ω RN021R2ZU001
R1074 METAL OXIDE FILM RES. 2W J 1.8 Ω RN021R8ZU001
R1075 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R1078 CARBON RES. 1/4W J 330 Ω RCX4JATZ0331
R1079 PCB JUMPER D0.6-P5.0 JW5.0T
R1080 CHIP RES. 1/10W J 2.7k Ω RRXAJR5Z0272
R1081 CHIP RES. 1/10W F 220 Ω RRXAFR5H2200
R1083 CARBON RES. 1/4W J 1.8 Ω RCX4JATZ01R8
R1084 CHIP RES. 1/10W J 220k Ω RRXAJR5Z0224
R1085 CHIP RES. 1/10W J 6.8k Ω RRXAJR5Z0682
R1086 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R1091 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R1096 PCB JUMPER D0.6-P5.0 JW5.0T
R1205 CHIP RES. 1/10W F 11k Ω RRXAFR5H1102
R1206 CHIP RES. 1/10W F 11k Ω RRXAFR5H1102
R1207 CHIP RES. 1/10W J 6.8k Ω RRXAJR5Z0682
R1208 CHIP RES. 1/10W J 6.8k Ω RRXAJR5Z0682
R1209 CHIP RES. 1/10W F 27k Ω RRXAFR5H2702
R1210 CHIP RES. 1/10W F 27k Ω RRXAFR5H2702
R1221 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104

20070307 1-17-2 E6E71EL

Ref. No. Description Part No.

R1222 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R1223 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471
R1224 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471
R1225 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R1226 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R1227 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221
R1228 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221
R1240 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R1245 CHIP RES. 1/10W J 10 Ω RRXAJR5Z0100
R1274 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R1351 CHIP RES. 1/10W J 2k Ω RRXAJR5Z0202
R1352 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222
R1353 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222
R1354 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221
R1355 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R1356 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R1392 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R1396 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471
R1397 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471
R1402 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R1421 CHIP RES. 1/10W F 200 Ω RRXAFR5H2000
R1422 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R1441 CHIP RES. 1/10W F 200 Ω RRXAFR5H2000
R1442 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R1443 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R1461 CHIP RES. 1/10W F 200 Ω RRXAFR5H2000
R1462 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R1481 CHIP RES. 1/10W F 200 Ω RRXAFR5H2000
R1482 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R1613 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R1614 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R2001 CARBON RES. 1/6W J 10 Ω RCX6JATZ0100
R2002 CHIP RES. 1/10W J 68k Ω RRXAJR5Z0683
R2012 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R2013 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R2014 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R2015 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R2016 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R2031 CHIP RES. 1/10W J 6.8k Ω RRXAJR5Z0682
R2032 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R2033 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R2041 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R2042 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R2043 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R2044 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103

MISCELLANEOUS

2B1 HOLDER F.I.P. E5900UD 0VM416070
AC1001# AC CORD PB8B2F9110A-055 WAC0162LW004
F1001# FUSE CURRENT PEG20C0NG001 PEG20C0NG001
FH1001 FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002
FH1002 FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002
FL2001 V.F.D. 7-BT-298NYM TVFD150FT014
JK1202 RCA JACK(BLACK) MSP-251V-01 NI FE LF JXRL010LY125
JK1401 S TYPE JACK MDC-050V-2.4 LF(B110 JXEL040LY003
JK1404 JACK RCA PCB L 06 MSP-246V29-65NI-F JXRL060LY153
RM2001 SENSOR REMOTE RECEIVER KSM-602LU2S USESJRSKK048
T1001# SWITCHING TRANS 7714 LTT2PC0KT022

FUNCTION CBA

Ref. No. Description Part No.

FUNCTION CBA
Consists of the following:

CONNECTOR

CN2101 6P FFC AV PCB TO SW PCB WX1E5900-005

SWITCHES

SW2101 TACT SWITCH SKQSAF001A SST0101AL041
SW2104 TACT SWITCH SKQSAF001A SST0101AL041
SW2105 TACT SWITCH SKQSAF001A SST0101AL041
SW2106 TACT SWITCH SKQSAF001A SST0101AL041
SW2107 TACT SWITCH SKQSAF001A SST0101AL041
SW2108 TACT SWITCH SKQSAF001A SST0101AL041

----------

20070307 1-17-3 E6E71EL

© 2007 Funai Electric Co., Ltd.

All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto
is strictly prohibited.

Information in this document is subject to change without notice. Funai reserves the right to change the content
herein without the obligation to notify any person or organization of such changes.

with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way
without the express written consent of Funai. All other trademarks used herein remain the exclusive property of
their respective owners. Nothing contained in this manual should be construed as granting, by implication or
otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any
other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights
to the fullest extent of the law.

DP170MS8

E6E71UD

2007-03-28