Magma A10-918 User Manual

OWNER’S MANUAL

™

Gourmet Series Marine Gas Grill

Model A10-918

For questions regarding performance, assembly,
operation, parts, or returns, contact the experts
at MAGMA by calling TOLL FREE IN U.S.A. AND
CANADA 1-800-86-MAGMA
7:00 a.m. - 5:00 p.m. Pacific Time Monday thru
Friday or e-mail us at [e-mail]

Read all instructions before operating. Save manual for future reference.

IMPORTANT SAFETY WARNINGS

READ ALL INSTRUCTIONS BEFORE OPERATING.

• USE OUTDOORS ONLY.

• DO NOT USE THIS APPLIANCE INSIDE THE BOAT OR ANY ENCLOSED SPACE.

• GRILLS RADIATE HEAT. CLEARANCE FROM COMBUSTIBLES, 24” SIDES AND
BACK. NEVER USE UNDER AWNINGS, PATIO COVERS, ETC.

• USE PROPANE GAS ONLY. FUEL STORAGE SHOULD BE IN COMPLIANCE WITH
THE AMERICAN BOAT AND YACHT COUNCIL (ABYC) STANDARDS A-1 (9),
MARINE LIQUIFIED PETROLEUM GAS (LPG) SYSTEMS.

• FOR NATURAL GAS APPLICATION CONTACT MAGMA.

• ALWAYS LIGHT GRILL WITH LID OPEN.

• NEVER LEAVE HOT GRILL UNATTENDED.

• USE HOT PAD WHEN HANDLING.

• ALWAYS TURN GRILL OFF AFTER USE.

Each Magma®Gas Grill is individually fire tested before it leaves the factory.

For this reason, the burner on your grill may be slightly discolored.

INSTALLATION INSTRUCTIONS

•Uses standard 1-lb. disposable propane canisters (DOT-39 NRC 228/286).

•Prior to installing valve, become familiar with the valve function and graphics
on valve knob. Never force the knob. Always turn or push gently.

•Turn control valve to “lock” and install gas canister being careful not to
cross the threads. Check for leaks prior to use.

•Position valve with gas bottle as shown (A).
Gently insert valve stem into valve chamber
while rotating until valve stem key aligns
with valve chamber lock detent allowing
valve to fully insert. Rotate gas canister
down and away so knob faces you (B) or
straight up (C) depending on application.

CONTROL VALVE REGULATOR

2

(C)

(A)

(B)

Fasteners are supplied for both Single Mount and Dual Mount grill mounting

MOUNT HARDWARE

options. See Magma Catalog or Website for best mount selection.

Single mount through-bolt

applications

4 Carriage bolts & lock nuts.

Single mount non-through-bolt

applications, including Style 1 “Levelock”

4 Hex head bolts & lock washers.

Dual mount applications

4 Carriage bolts & lock nuts. Only 4 bolts

required for grill mounting. Place bolts (2 per

side) diagonally from each other as shown.

Carriage bolt

& lock nut

Hex head bolt
& lock washer

ON-BOARD FUEL SYSTEMS APPLICATION

•For on-board LPG (Propane) Systems, use Magma Type 3-Low Output­Low Pressure LPG Control Valve and Magma Low Pressure LPG Hose Kit.

•For on-board CNG (Natural Gas) Systems, use Magma Type 4-Low Output­Low Pressure Natural Gas Control Valve.

See Magma website for
replacement part numbers
and valve applications.

www.MagmaProducts.com

Grill Grates

Lid Lock

Radiant Plate

Liner

Match Light
Hole

Burner

Outer Shell

Valve Chamber

Mount
Support Pad

Slide Out
Grease Tray

Control Valve
Regulator
Type 1 Low­Output Shown

Piezo Igniter

3

OPERATING PROCEDURES

OPERATE ONLY ON “LOW” WHEN LID IS CLOSED.
ALWAYS OPERATE WITH GREASE TRAY IN PLACE.

WARNING: Do not overheat grill.
Stainless Steel loses anti-corrosive characteristics when subjected to extreme
heat. Most grilling is done on low temperature with the lid closed. If medium
or high heat is required, grill with lid open.

• Open lid during lighting.

• Depress knob and rotate counter-clockwise to the “HIGH” flame position.

• Push Piezo Igniter.

• Visually confirm ignition through match light hole.

• Turn knob to adjust flame.

• If grill does not light, repeat process.

• Open lid during lighting.

• Depress knob and rotate counter-clockwise to the “HIGH” flame position.

• Hold match or gas flame long lighter up to the match light hole.

• Visually confirm ignition through match light hole.

• Empty and clean grease tray prior to each use.

• Trim excess fats from meat.

• Use non-oil based marinades.

• Reduce heat.

• Use water spray directly on flare-ups.

NOTE: Before lighting, lid lock must be positioned not to engage. Open lid
and turn lock to locked position, or bring lock latch up to handle in open
position and flip lock actuator back onto handle.

Before lighting your grill, be sure that …

•

Grill is secure and properly mounted.

•

Internal components and grease tray are clean and correctly positioned.

•

You have plenty of gas in the canister.

•

Gas canister is attached properly and there are no gas leaks.

•

Lid lock has been set not to engage.

•

You have a water spray bottle handy to cool a hot grill or stop any flare-ups.

• Always disconnect the fuel canister from the valve prior to stowing.

• Stow the valve in a clean, dry area to protect from corrosion to valve.

•

Always store propane in a sealed propane storage locker that allows leakage

to vent overboard or use Magma A10-210 Propane Storage Tote.
Never stow below decks

MATCH LIGHTING INSTRUCTIONS

Magma Grills do not require pre-heating.

LIGHTING INSTRUCTIONS

TO REDUCE FLARE-UP

PRACTICAL HINTS:

STOWING TIPS

4

ELECTRODE SPARK ADJUSTMENT

CAUTION: Spark can cause small shock. Do not leave fin­gers on or near electrode wire while engaging igniter.

• Electrode wire should be
exit hole in burner

A

approximately 1/8” from gas

. Carefully adjust wire if required.

DISASSEMBLY & RE-ASSEMBLY

•

Lift radiant plate up & out of left slot (see B) and remove by sliding it out of
right slot (see C).

•

Remove burner screw (see B) and remove burner. Check burner for grease
residue or spider webs that may obstruct gas flow. CAUTION: WHEN REPLAC­ING BURNER, CUT SLOT IN BURNER MUST FACE DOWN.

•

To remove liner from outer shell you must disconnect the electrode wire (see
D). First remove the two screws on valve chamber (see D) and remove the
cover plate. Gently pull wire off connector (see D). It is not necessary to
remove electrode from liner.

•

Remove Lid and liner by removing hinge screws and lock nuts with 3/16”
hex key wrench (supplied) and 1/2” wrench or pliers. CAUTION: LOCK NUTS
MUST BE INSTALLED WITH LOCKING INDENT MARKS SHOWING (see E).
IMPROPER INSTALLATION WILL DAMAGE THE HINGE SCREW AND LOCK NUT.

•

Lift liner out of outer shell by lifting up on liner lip on back side of liner
(see F). When replacing liner, be sure top lip of liner installs over top edge of
outer shell (start with corners of lip and work in).

• Inspect burner, remove any obstructions.

• Clean as indicated in Maintenance (page 6).

• To re-assemble, reverse the procedure.

Disconnect wire

B

Left
side
slot

C

Right
side
slot

D

Burner screw

E

Locking
Indents

5

Electrode

Electrode

F

Screws

Liner Lip

Liner

Outer Shell

MAINTENANCE

Propane (LPG)

Gas Regulator

A10-225
Hose Kit

To other LPG

appliance
or use cap

Shut off

valve

Cylinder Valve

Gauge

Type 3

Valve

Solenoid

Gourmet

Gas Grill

Typical Marine &
R.V. Application

Align valve stem key
to valve chamber
lock detent and rotate

Gourmet
Gas Grill

Gourmet

Gas Grill

Type 3
Valve

About Stainless Steel - Stainless steel exposed to prolonged periods of high heat will change
color and texture. Magma grills require no preheating. Not preheating will keep your grill cooler
and greatly extend the life and beauty of your grill. Texture and color change is normal on
interior components and will not affect the product’s operation or performance.

Exterior Stainless Steel Components - Cleaning the exterior surface after every use will help
prevent discoloration. Use soapy water with a soft cloth or sponge. Rinse thoroughly with fresh
water and dry. We recommend covering the grill between uses. Optional covers are available
from Magma retailers or direct from Magma. CAUTION: ABRASIVE PADS OR CLEANERS WILL
DAMAGE THE FINISH.

Interior Components - Remove heavy residue from grill and empty grease tray between
each use. We recommend complete disassembly and cleaning at least once a year depending
on amount of use (see page 5) and always prior to long term storage. For burnt-on residue we
recommend Easy-Off brand Oven & Grill Cleaner. If cleaner is used on liner or lid, complete
disassembly is recommended to remove any cleaner residue left between components. Wash
all components with soapy water after using cleaner. CAUTION: AVOID CONTACT OF IGNITER
AND ELECTRODE WIRE AND WIRE CONNECTORS WITH OVEN CLEANER.
Grill Grates - Clean with brass wire brush while grill is warm. Use Oven & Grill cleaner for
burnt-on residue. Wash with soapy water and dry prior to storage.

Ceramic Electrode - Located just beside the burner, it should be kept clean of grease and
debris. Be careful not to damage the ceramic insulation or bend the wire. See page 5 for
electrode spark adjustment.

Control Valve - All valves are set and tested at our factory. Do not attempt to adjust or
disassemble the valve in any way. Call Magma if you suspect it is not adjusted properly. Clean
valve with a cloth and remove any debris obstructing the gas outlet orifice using a pin or needle.

Repair/Replacement Parts - See Magma’s Website for a complete list of Repair or
Replacement Parts. www.MagmaProducts.com

USING GRILL WITH ON-BOARD LPG (PROPANE) SYSTEMS

• Magma On-Board LPG (Propane) Valves
and Hose Kits allow Magma Grills to be
installed within a boats existing on-board,
pre-regulated low pressure LPG (Propane)
system.

• Use only Magma Type 3 Low
Pressure LPG (Propane) Valves. See
our Valve Application Guide at www.
MagmaProducts.com for correct valve.

• In North America use Magma A10-225

LPG 10' Hose Kit in conjunction with
Type 3 Valve. Outside North America check

your local dealer for proper hose and fittings.

• A primary shutoff valve (supplied with
A10-225 hose kit) must be used with this
control valve at point of connection into
your system. This allows shut off of gas
supply to hose leading to grill.

6

TROUBLE SHOOTING GUIDE

Problem

Burner will not
light with igniter

Burner will not
light even with
match

Flare-up

Possible Cause

Igniter electrode covered with
grease or residue

Igniter/electrode too far from
burner

Igniter/electrode wire loose or
disconnected

Wire is shorted causing spark
from wire before electrode

No spark being generated

No gas flow

Obstructed gas flow/debris or
spider webs in burner tube

Excessive cooking temperature

Grease and/or residue build-up

Excessive fat in meats

Possible Solution

Clean igniter electrode

Adjust electrode until proper
spark appears (see page 5)

Reconnect wire between ignit­er & electrode (see page 5)

Call Magma

Call Magma

Check fuel level, refill cylinder
or replace canister

Clean valve orifice and burner,
check all lines (see page 6)

Operate only on low when
lid is closed
Reduce flame level
Leave lid open
Use water spray to cool

Clean components

Trim fat from cuts of meat
before grilling

Yellow sooty flame

Blow-out

Excessive oils in marinades

Obstructed gas flow/debris or
spider webs in burner tube

Flame too low

Wind directly on burner

Obstructed gas flow

7

Use non-oil based marinades

Check and clean valve orifice
and burner (see page 6)

Increase flame

Block wind when opening lid

Clean burner or valve orifice
(see page 6)

83-918 1105

Magma Products, Inc.

3940 Pixie Avenue, Lakewood, CA 90712 • USA

Phone [phone] • e-mail: [e-mail]

www.MagmaProducts.com

Magma Products, Inc. guarantees this gas grill to be free from defects in materials or workmanship to the original consumer. This guarantee is for the periods
herein specified when used under normal and reasonable conditions, one (l) year from the date of original purchase. This warranty does not include the cost of
property damage or any inconvenience due to the failure of the product. Nor does it cover damage due to misuse, abuse, accident, or damage resulting from
transportation of the product. Nor does it include damage resulting from the commercial use of this product. If the product fails to operate due to a defect in
materials or workmanship during the warranty period, the defective part will be repaired or replaced at Magma's option. If you wish to obtain performance under
this limited warranty, you should contact Magma's Customer Service Department via telephone at 562-627-0500 or 800-86-MAGMA, or via e-mail at
[e-mail], or via U.S. Postal Service mail at “Magma Products, Inc., attention Customer Service, 3940 Pixie Ave. Lakewood, CA, 90712.“ The defective
part, along with proof of purchase, must be returned postage prepaid to Magma Products, Inc. We suggest that you keep your purchase receipt as we may require
reasonable proof of purchase.

In the state of California only, if refinishing or replacement of the product is not commercially practicable, the retailer selling the product, or Magma Products,
Inc., will refund the purchase price paid for the product, less the amount directly attributable to use by the original consumer prior to the discovery of the
nonconformity. In addition, in the state of California only, you may take the product to the retail establishment from which it was purchased or to any retail
establishment selling this product in order to obtain performance under this warranty.

All implied warranties, including the implied warranties of merchantability and fitness for a particular purpose, are limited in duration to the express warranty
periods specified herein for the parts described herein.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Neither Magma dealers, nor the
retail establishment selling this product has any authority to make any warranties or to promise remedies in addition to or inconsistent with those stated above.
Magma's maximum liability shall not exceed the purchase price of the product paid by the original consumer. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusions may not apply to you. The warranty gives you specific legal rights and you may also have
other rights which vary from state to state.

MAGMA and the Magma logo are registered trademarks of Magma Products, Inc.
Newport is a trademark of Magma Products, Inc.
Patent pending.

CALIFORNIA PROPOSITION 65 – WARNING – The burning of gas cooking fuel generates some by-products, which are on the list of substances,
which are known by the State of California to cause cancer or reproductive harm. California law requires businesses to warn customers of
potential exposure to such substances. To minimize exposure to these substances, always operate this unit according to the use and care
manual, ensuring you provide good ventilation when cooking with gas.

Contents

x 4 x 4

A

B

C

x 4x 4

A) (1) 3/16” Hex key wrench for lid removel.
B) Pack of (4) 1/4”-20 x 5/8” hex head screws

and internal lock washers for “Levelock”
single mount application.

C) Pack of (4) 1/4”-20 x 5/8” carriage bolts and

lock nuts for dual mount and single mount
applications and table legs.

LIMITED WARRANTY