SCOPE
：
(1) SHAPES AND DIMENSIONS
(2) ELECTRICAL SPECIFICATIONS
(3) CHARACTERISTICS
This specification applies to the Pb Free high current type SMD inductors for
MSCDRI-2D11HP-SERIES
PRODUCT INDENTIFICATION
MSCDRI - 2D11HP - 3R3 N
① ② ③ ④
① Product Code
② Dimensions Code
③ nductance Code
④ Tolerance Code
A: 3.00±0.2 mm
B: 3.00±0.2 mm
C: 1.20 Max. mm
D: 4.50 Max. mm
E: 2.10 Typ. mm
F: 1.00 Typ. mm
SEE TABLE 1
TEST INSTRUMENTS
L : HP 4284A PRECISION LCR METER (or equivalent)
RDC : CHROMA MODEL 16502 MILLIOHMMETER (or equivalent)
(3)-1 Ambient temperature ……......... ＋60℃ Max.
(3)-2 Operate temperature range ...... －40℃～＋125℃
(Including self temp. rise)
(3)-3 Storage temperature range ...... －40℃～＋125℃
MAG.LAYERS
MSCDRI-2D11HP-SERIES Page 1/8
TABLE 1
MAGLAYERS
PT/NO.
MSCDRI-2D11HP-1R5□
Inductance Percent Test Resistance Rated DC Current
L(μH) Tolerance Frequency RDC(Ω) Max. IDC1(A) IDC2(A)
1.5 N 100kHz/0.25V 80m 1.35 1.60 1R5
Marking
MSCDRI-2D11HP-2R2□
MSCDRI-2D11HP-3R3□
MSCDRI-2D11HP-4R7□
MSCDRI-2D11HP-6R2□
MSCDRI-2D11HP-6R8□
MSCDRI-2D11HP-100□
MSCDRI-2D11HP-220□
MSCDRI-2D11HP-330□
※ □ specify the inductance tolerance,M(±20%),N(±30%)
※ IDC1： Based on inductance change (△L/Lo： ≦ drop 35%) @ ambient temp. 25℃
IDC2： Based on temperature rise (△T： 40℃ TYP.)
Rated DC Current： The less value which is IDC1 or IDC2.
2.2 M,N 100kHz/0.25V 0.120 1.10 1.30 2R2
3.3 N 100kHz/0.25V 0.173 0.90 0.90 3R3
4.7 N 100kHz/0.25V 0.238 0.75 0.85 4R7
6.2 M,N 100kHz/0.25V 0.371 0.63 0.65 6R2
6.8 N 100kHz/0.25V 0.371 0.63 0.65 6R8
10 M,N 100kHz/0.25V 0.559 0.52 0.52 100
22 M,N 100kHz/0.25V 1.300 0.33 0.40 220
33 M,N 100kHz/0.25V 1.520 0.25 0.35 330
MAG.LAYERS
MSCDRI-2D11HP-SERIES Page-2/8
(4) RELIABILITY TEST METHOD
MECHANICAL
TEST ITEM SPECIFICATION TEST DETAILS
Substrate bending
△L/Lo≦±5%
There shall be direction is made approximately 3mm.(keep time 30 seconds)
no mechanical PCB dimension shall the page 7/9
damage or elec- F(Pressurization)
trical damege.
The sample shall be soldered onto the printed circuit board
in figure 1 and a load applied unitil the figure in the arrow
PRESSURE ROD
figure-1
Vibration
Solderability
△L/Lo≦±5%
There shall be and a frequency of from 10 to 55Hz/1 minute repeated should
no mechanical be applied to the 3 directions (X,Y,Z) for 2 hours each.
damage. (A total of 6 hours)
New solder Flux (rosin, isopropyl alcohol{JIS-K-1522}) shall be coated
More than 90% over the whole of the sample before hard, the sample shall
The sample shall be soldered onto the printed circuit board
and when a vibration having an amplitude of 1.52mm
then be preheated for about 2 minutes in a temperature of
130～150℃ and after it has been immersed to a depth 0.5mm
below for 3±0.2 seconds fully in molten solder M705 with
a temperature of 245±5℃.
More than 90% of the electrode sections shall be couered
with new solder smoothly when the sample is taken out of
the solder bath.
MAG.LAYERS
MSCDRI-2D11HP-SERIES
Page-3/8
Loading...