INSTALLATION INSTRUCTIONS
Louver Kit
For Use with MGE/MCE/MHP Series Magic-Pak® Units
This manual must be left with the homeowner for future reference.
WARNING
The Magic-Pak® unit must be installed with approved
wall sleeve and grille accessories for safe operation.
Improper installations could result in property damage,
personal injury, or death.
WARNING
Installation
Magic-Pak louvers are designed for installation on MagicPak Wall Sleeves.
In accordance with the 2014 Florida Building Code, it may
be required to use specic fastening methods depending
on the risk category and wind exposure classication
of the project where the equipment is being installed.
Please refer to our wind load certication documentation
prescribing installation and fastener requirements at www.
magic-pak.com/literature.
Adequate safety precautions should be taken to protect
personnel. Improper installations could result in property
damage, personal injury, or death.
Shipping and Packing List
Qty Description
1 Louver
1 Mounting Hardware Packet
1 Installation Instructions
Gasket
1
(Factory-installed for aluminum louvers)
(Field-installed for plastic louvers)
Manufactured By
Allied Air Enterprises LLC
A Lennox International, Inc. Company
215 Metropolitan Drive
West Columbia, SC 29170
*P508024-01*
(P) 508024-01
NOTE: Louvers should be tethered during the installation
process to reduce the risk of dropping.
Gasket -
Attached to
V-Shaped
Louver
Divider
Panel
1. Remove cardboard template (if present) from wall
sleeve opening.
2. Apply supplied gasket to the interior at surface of the
V-shaped dividing louver (see gure above). Gasket
must align with wall sleeve divider panel (or unit fan
panel if using ASLEEVE-3) to form a seal between
louver and divider panel.
NOTE: Gasket is factory-applied to aluminum louvers.
Louver
Wall Sleeve
Assembly
508024-01 Issue 2109 Page 1 of 3
3. Install fasteners into the louver’s two upper and
two lower mounting holes. Do not seat fasteners
5. Install two middle fasteners.
6. Tighten all fasteners to secure louver to wall sleeve.
completely (leave approximately 1/8” to 1/4” gap for
tment in step 4).
NOTE: If additional sealing between wall sleeve and louver
is desired, it is important to only caulk the left, right, and top
4. Guide louver through wall sleeve opening and insert
fasteners into upper and lower key holes of the wall
sides. A gap between the bottom of the louver and the wall
sleeve is required to allow proper rain water drainage.
sleeve.
Magic-Pak Model
MGE MHP MCE
Accessory Nomenclature
**MGE4-11-091*P
**MGE4-11-121*P
**MGE4-11-181*P
**MGE4-11-241*P
**MGE4-11-301*P
**MGE4-11-361*P
*MHP4-11-091*P
Polypropylene Louver Kit - White
(29" Height)
Polypropylene Louver Kit - White
(33" Height)
Polypropylene Louver Kit - White
(45" Height)
Polypropylene Louver Kit - Sandstone
(29" Height)
Polypropylene Louver Kit - Sandstone
(33" Height)
Polypropylene Louver Kit - Sandstone
(45" Height)
Polypropylene Louver Kit - Beige
(29" Height)
Polypropylene Louver Kit - Beige
(33" Height)
Polypropylene Louver Kit - Beige
(45" Height)
Polypropylene Louver Kit - Taupestone
(29" Height)
Polypropylene Louver Kit - Taupestone
Polypropylene Louvers
(33" Height)
Polypropylene Louver Kit - Taupestone
(45" Height)
Polypropylene Louver Kit - White
(29" Height / MGE)
Polypropylene Louver Kit - White
(33" Height / MGE)
Polypropylene Louver Kit - White
(45" Height / MGE)
Polypropylene Louver Kit - Sandstone
(29" Height / MGE)
Polypropylene Louver Kit - Sandstone
(33" Height / MGE)
Polypropylene Louver Kit - Sandstone
(45" Height / MGE)
Wall sleeve and louver sizes equal to the required wall opening dimensions for the unit size
●
○ Optional: Wall sleeves and louvers can be oversized to maintain a uniform appearance
ALVRPWHT-1 ● ● ● ● ● ● ●
ALVRPWHT-2 ● ● ●
ALVRPWHT-3 ● ● ● ● ● ● ● ● ● ● ● ●
ALVRPSAN-1 ● ● ● ● ● ● ●
ALVRPSAN-2 ● ● ●
ALVRPSAN-3 ● ● ● ● ● ● ● ● ● ● ● ●
ALVRPBGE-1 ● ● ● ● ● ● ●
ALVRPBGE-2 ● ● ●
ALVRPBGE-3 ● ● ● ● ● ● ● ● ● ● ● ●
ALVRPTPST-1 ● ● ● ● ● ● ●
ALVRPTPST-2 ● ● ●
ALVRPTPST-3 ● ● ● ● ● ● ● ● ● ● ● ●
ALVRPWHTMGE-1 ● ● ● ●
ALVRPWHTMGE-2 ●
ALVRPWHTMGE-3 ●
ALVRPSANMGE-1 ● ● ● ●
ALVRPSANMGE-2 ●
ALVRPSANMGE-3 ●
Table 1. Available Louver Kits
*MHP4-11-121*P
*MHP4-11-181*P
*MHP4-11-241*P
*MHP4-11-301*P
*MHP4-11-361*P
*MCE4-11-091*P
*MCE4-11-121*P
*MCE4-11-181*P
*MCE4-11-241*P
*MCE4-11-301*P
*MCE4-11-361*P
508024-01Issue 2109Page 2 of 3