Magic Chef CER3520AAA, CER3520AAH, CER3520AAL, CER3520AAT, CER3540AAA Installation Instructions

INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE I~PPLIANCE

THE MANUAL IS INTENDED TO ASSIST IN THE INITIAL INSTALLATION AND ADJUSTMENTS OF THE RANGE.

ccccccccc ccccc ccccc

INSTALL OR SERVICE THIS RANGE.

ADJUSTMENt ALTERATION SERVICE

CLEARANCE DIMENSIONS

For complete information in regard to installation of range. see figures 1 and 2 on page 2. For SAFETY

CONSIDERATIONS, do not install a range in any combustible cabinetry which is not in accord with the installation

clearances shown in figure 1 on page 2.

CAUTION: SOME CABINETS AND BUILDING MATERIALS ARE NOT DE:SIGNED TO WITHSTAND

THE HEAT PRODUCED BY THE NORMAL SAFE OPERATION OF A LISTED APPLIANCE.
DISCOLORATION OR DAMAGE, SUCH AS DELAMINATION, MAY OCCUR.

8101P120-60

(03-95-00)

~

A. Do not attempt to operate this oven with the door open

since open-door operation can result in harmful
exposure to microwave energy. It is important not to
defeat or tamper with the safety interloc:ks.

B. Do not place any object between the oven front face

and the door or allow soil or cleaner residue to
accumulate on sealing surfaces.

c

Do not operate the oven if it is damaged. It is
particularly important that the oven door close

properly and that there is no damage to the: (1) Door

(bent), (2) hinges and latches (broken or loosened),

(3) door seals and sealing surfaces.

D

The oven should rlot be adjusted or repaired by
anyone except properly qualified service personnel. I

IMPORTANT -PLEASE KEEP FOR THE USE OF THE LOCAL ELEC:TRICAL INSPECTOR.

"A" = 30 inches minimum clearance between the top of the cooking surface and the
bottom of an unprotected wood or metal cabinet, or "A" = 24 inches minimum when

bottom of wood or metal cabinet is protected by not less than 1 /4-inch thick flame-

retar(jant millboard covered with not less than No. 28 MSG sheet steel, 0.015-inch

thick stainless steel, 0.024-inch thick aluminum, or 0.020-inch thick copper.

To eliminate the risk of burns orfire by reaching over heated surface units, cabinet
storage space located above the surface units should be avoided. If cabinet storage

is to be provided, the risk can be reduced by installing a range hood that projects

horizontally a minimum of 5 inches beyond the bottom of the cabinets.

1, 2, 3 -COMBUSTIBLE BUILDING WALLS.

4 -COMBUSTIBLE WALL CABINET.

A FREE-STANDING RANGE MAY BE IN~)TALLED ADJACENT TO (0" FROM) COMBUSTIBLE WALLS 1, 2 & 3

-2-

1611

36'1 COUNTER

TOP HEIGHT

5 3/411

3011 CAB I NET

OPENINGS.

UPPER & LOWER

PROVIDE FOR 120/240 VOLT
OUTLET IN THIS AREA.

Electric Free-Standing Ranges

The installation of a range designed for mobile home
installation must conform with the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home
Construction and Safety, Title 24 HUD, Part 280) or, when
such standard is not applicable, the Standard for
Manufactured Home Installations 1982 (Manufactured
Home Sites, Communities and Set-Ups), ANSI

A225.1-1984, or with local codes.

FIGURE 2

Place range where it will be well lighted. Do not set range

over holes in the floor or other locations where it may be

subject to strong drafts. Any opening in the wall behind the
range and in the floor under the range should always be
sealed. Make sure the flo~' of combustion or ventilation air is

not obstructed.

"j

~ TOP DEPTH

""

"-

2411 CAB I NET

DEPTH. I

r'

25 II NORMA L

COUNTER

"'-

-3-

~~