Coi| E|ec ric Range
Care & CJeaning ................... 17-20
Sdf-CHean Oven
Qeaning Procedures
Maintenance ......................... 21-22
OvenWindow
Oven Light
Troubleshooting ................... 23-24
Warranty & Service .................... 25
Guide de utilisateur ................... 26
Gu_a del Usuario ......................... 54
Form No. B/11/04 Part No 8113P473-60 ,3;)2004 Maytag Appliances Sales Co. Litho USA
[nstaller: Please leave this rnanuaIwith this appfiance
Consumer: Phase read and keep this manual for future
reference. Keep sales receipt and, or canceled check as proof
of purchase.
Mode[ Number
Serial Number
Date of Purchase
if you have questions, call:
1-800-688-1120 {U.S.A.and Canada_
1-800-688-2080 { U.S.TTY for
hearing or speech impaired}
(Mon.-FrL 8 am-8 pm Eastern Time}
in our continuing effort to [mprovethe qualityand performance
of our cooH ng products, it ma} be necessary to make changes
to the appliance without revising this guide.
For service intfermatie#, see page 25.
To ensure proper and safe operation: Appliance must be
properly installed and grounded by a qualified technician.
Do not attempt to adjust, repair, service, or replace any paRR
of your appliance unless it is specifically recommended in
this guide. All other servicing should be referred to a
qualified servicer.
Always disconnect power to appliance before servicing.
ALL RANGES CAN TiP AND
CAUSE iNJURiES TO PERSONS
_ INSTALL ANTra:TraP DEVICE
PACKED WiTH RANGE-
, FOLLOW ALL [NSTALLATmON
tipping of the appliance from o
abnormal usage or by
loading of the oven door, the appliance must
be secured by a properly installed anti4ip
device.
Warning and Important Safety Instructions appearing in this
guide are not meant to cover all possible conditions and
situations that may occur. Common sense, caution, and care
must be exercised when installing, maintaining, or operating
the appliance.
Always contact the manufacturer about problems or
conditions you do not understand.
Recognize Safety Symbols, Words, Labels
WARNnNG _ Hazards or unsafe practices which COULD
CA[JT_ON - Hazards or' unsafe practices which COULD
result in minor persona[ injury.
Read and follow aH instructions before using this
appliance to prevent the potential risk of fire, electric
shock, personal injury or damage to the appliance as a
result of improper usage of the appliance. Use appliance
only for its intended purpose as described in this guide.
To check if device is properly installed, look underneath
range with a flashlight to make sure one of the rear leveling
legs is properly engaged in the bracket slot. The anti-tip
device secures the rear bveiing legto the floor when
properly engaged. You should check this anytime the
range has been moved.
To Prevent Fire or Smoke
Be sure air packing materials are removed from the appli-
ance before operating it.
Keep area around appliance dear and free from combus-
tible materials. Flammable materials should not be stored in
an oven.
Many plastics are vuLnerabLeto heat. Keep plastics away
from paRRsof the appliance that may become warm or hot.
To prevent grease fires, do not Letcooking grease or other
flammable materials accumulate in or near the appliance.
in Case of Fire
Use dry chemical or foam-type extinguisher or baking soda
to smother fire or flame. Never use water on a grease fire.
1. Turn off appliance to avoid spreading the flame.
2. NEVER pick up or move a flaming pan.
3. Smother oven fire or flame by dosing the oven door.
Child Safety
NEVER store items of interest to children Jncabinets above
an appliance, Children climbing on the app!!ance or on the
appliance door to reach items could be seriously injured.
NEVER leave children alone or unsupervised near the
appliance when it is in use or is stfll hot. Children should
never be allowed to sit or stand on any part of the appliance
as they could be injured or burned.
Children must be taught that the appliance and utensils in it
can be hot. Let hot utensils cool in a safe place, out of reach
of small children. Children should be taught that an appliance
is not a toy. Children should not be allowed to playwith
controls or other parts of the appliance.
About Your Appmianee
NEVER USean app!!ance aSa step to reach cabinets above,
Misuse of appliance door, such as stepping, leaning or
sitting on the dooh may result in possible tipping of the
To prevent potential hazard to the user and damage to the
appliance, do not use appliance as a space heater to heat or
warm a room. Also, do not use the oven as a storage areafor
food or cooking utensils.
Do not obstruct the flow of air by blocking the oven venL
DO NOT TOUCH HFATING ELEMENTS OR iNTERiOR
SURFACESOF OVEN. Heating elements may be hot even
though they are dark in color, interior surfaces of any oven
become hot enough to cause burns. During and after use, do
not touch, or let clothing or other flammable materials contact
heating elements or interior surfaces of oven until they have
had sufficient time to cool Other surfaces of the appliance
may become hot enough to cause burns - among these
surfaces are: oven vent opening, surface near this opening,
oven door and window of oven door.
Do not touch a hot oven light bulb with a damp cloth as the
bulb could break. Should the bulb break disconnect power to
the appliance before removing bulb to avoid electrical shock
NEVER use aluminum foil to cover an oven rack or oven
bottom. Misuse could result in risk of electric shock, fire, or
damage to the appliance. Use foil only as directed in this
guide.
Cooking Safety
Never heat an unopened food container in the oven. Pressure
build-up may cause container to burst resulting in serious
personal injury or damage to the appliance.
Use dry, sturdy potholders. Damp potholders may cause
burns from steam. Dish towels or other substitutes should
never be used as potholders because they can trail across hot
elements and ignite or get caught on appliance parts.
Wear proper apparel. Loose fitting or long hanging-sleeved
apparel should not be worn while cooking. Clothing may
ignite and cause burns if garment comes in contact with
heating elements.
Always place oven racks in the desired positions while oven is
cool. Slide oven rack out to add or remove food, using dry,
sturdy potholders. Always avoid reaching into the oven to add
or remove food. If a rack must be moved while hot, use a dry
potholder. Do not let potholder contact hot element in oven.
Use racks only in the oven in which they were shipped/
purchased.
Use care when opening the oven door. Let hot air or steam
escape before removing or replacing food.
PREPARED FOOD WARNING: Follow food manufactureCs
instructions. If a plastic frozen food container and/or its cover
distorts, warps, or is otherwise damaged during cooking,
immediately discard the food and its container. The food
could be contaminated.
Do not allow aluminum foil or meat probe to contact heating
element.
Always turn off allcontrols when cooking is completed.
Utensim Safety
Follow the manufacturer's directions when using oven
cooking bags.
This appliance has been tested for safe performance using
conventional cookware. Do not use any devices or accesso-
ries that are not specifically recommended inthis guide. Do
not use eyelid covers, stove top grills or add-on oven convec-
tion systems. The use of devices or accessories that are not
expressly recommended inthis guide can create serious
safety hazards, result in performance problems, and reduce
the life of the components of the appliance.
2
If pan issmaller than element, a portion of the element will be
exposed to direct contact and could ignite clothing or
potholder.
Only certain types of glass, glass!ceramic, ceramic, eaRRhen-
ware, or other glazed utensils aresuitable for cooktop or oven
service without breaking due to the sudden change in
temperature. Follow utensil manufacturer's instructions when
using glass.
Turn pan handle toward center of cooktop, not out into the
room or over another surface elemenL This reduces the risk
of burns, ignition of flammable materials, or spillage [f pan is
accidently bumped or reached by small children.
Be sure utensil is large enough to properly contain food and
avoid boi[overs. Pan size is particularly important in deep fat
frying. Be sure pan will accommodate the volume of food that
is to be added as we[[ as the bubble action offal
Never let a pan boil dry as this could damage the utensil and
the appliance.
Deep Fat Fryers
Use extreme caution when moving the grease pan or dispos-
ing of hot grease. Allow grease to cool before attempting to
move pan.
Ventimating Hoods
Clean range hood and filters frequently to prevent grease or
other flammable materials from accumulating on hood or
filter and to avoid grease fires.
When flaming foods under the hood, turn the fan on.
C eaning Safety
Clean cooktop with caution. Turn off all controls and wait for
appliance paRRsto cool before touching or cleaning. Clean
with caution. Usecare to avoid steam burns if a wet sponge
or cloth is used to wipe spills on a hot surface. Some cleaners
can produce noxious fumes if applied to a hot surface.
Clean only paRRslisted in this guide.
NEVER leave surface units unattended especially when using
high heat An unattended boi[over could cause smoking and
a greasy spi[[over can cause a fire.
This appliance isequipped with different size surface ele-
ments. Select pans with flat bottoms large enough to cover
element. Fitting pan size to element will improve cooking
efficiency.
CoimEmements
To prevent damage to removable heating elements, do not
immerse, soak or clean in a dishwasher or self-clean oven. A
damaged element could short resulting in a fire or shock
hazard.
Make sure drip bowls are in place as absence of these bowls
during cooking could damage wiring.
Protectmve Liners: Do not use aluminum foil to line surface
unit drip bowls or oven bottoms, except as suggested inthe
manual Improper installation of these liners may result in a
risk of electric shock or fire.
Se f-C ean Oven (select models}
DOnot !eaveracks,broiling pan,food orco0kJng utensils,etc.
Do not clean door gasket The door gasket is essential for a
good seal. Care should be taken not to rub, damage, or move
the gasket.
Do not use oven cleaners or oven liners of any kind in or
around any paRRof the self-clean oven.
Before self-cleaning the oven, remove broiler pan, oven racks
and other utensils, and wipe off excessive spillovers to
prevent excessive smoke or flare ups.
It is normal for the cooktop of the range to become hot
during a self-clean cycle. Therefore, touching the cooktop
during a clean cycle should be avoided.
3
l portant Safety Notice and
The California Safe Drinking Water and Toxic Enforcement
Act of 1986 (Proposition 65) requires the Governor of Califor-
nia to publish a list of substances known to the State of
California to cause cancer or reproductive harm, and requires
businesses to warn customers of potential exposures to such
substances.
Users of this appliance are hereby warned that when the
oven is engaged in the self-clean cycle, there may be some
low-level exposure to some of the listed substances, including
carbon monoxide. Exposure to these substances can be
minimized by properly venting the oven to the outdoors by
opening the windows and!or door in the room where the
appliance is located during the self-clean cycle.
UMPORTANT NOTICE REGARDUNG PET BURDS: Never
keep pet birds in the kitchen or in rooms where the fumes
from the kitchen could reach. Birds have a very sensitive
respiratory system. Fumes released during an oven self-
cleaning cycle may be harmful or fatal to birds. Fumes
released due to overheated cooking off,fat, margarine and
overheated non-stick cookware may be equally harmful.
Save These instructions for Future Reference
4
Surface Controls
Use to turn on the surface elements. An hfhite choice of
heat settings is avaiHabHefrom Low to High. The knobs can
be set on or between any of the settings.
Setting the Controls
1. Place pan on surface element.
2. Push in and turn the knob in either direction to the desired
heat setting.
° The control panel is marked to identify which _J_
element the knob controls. For example, the
graphic at right indicates left front element.
3. There is an element "ON" indicator light on the control
panel. When any surface control knob is turned on, the
light will turn on. The light will turn off when all the
surface elements are turned off.
4. After cooking, turn knob to OFF. Remove pan.
Suggested Heat Settings
The size,type of cookware and cooking operation will affect the
heat setting. For information on cookware and other factors
affecting heat settings, refer to "Cooking Made Simple" booklet.
High (10): Use to bring
warm and melt chocolate |
Low (2): Use to keep foods 1
and butter. |
Me& Low (3°4):
Use to continue
cooking covered
foods or steam
foods.
[
3
4
liquid to a boil. Always
reduce setting to a lower
heat when liquids begin to
boil or foods begin to cook.
OFF I
J
Mediu_
fVledium (5-7): Use to
maintain slow boil for
large amounts of liquids
and for most frying
operations.
(Style varies by model]
Medo High (8-9): Use
to brown meat, heat oil
for deep fat frying or
sauteing. Maintain fast
boil for large amounts
of liquids.
BEFORECOOK|N61 AFTER COOKING
o Always place a pan on the surface unit before you turn it o Make sure sutrace unit is turned off.
on. To prevent damage to rail .]e. never operate surface - Clean up messy spills as soon as possible.
unit without a pan in place.
o NEVER use the cooktop as a storage area for rood or
cookware
[:)BRING COOK|NG
o Besure you know which knob controls which surface
unit. Make sure you turned on the correct surface unit.
• Begin cooking on a higher heat setting then reduce to a
lower setting to complete the operation. Never use a
high heat setting for extended cooking.
o NEVER allow a pan to boil dry. This could damage the
pan and the appliance
o NEVER [ouch cooktop until it has cooled. Expect some
parts of the cooktop, especially around the surface units.
te uecome warm or hot during cooking. Use potholders
to protect hands.
OTHERTraPS
° If cabinet storage msprovided directly above cooking
sur[ace. limit it to items that are infrequently used and can
be safely storee n an area subjected to heat. Tempera-
lures ma,_be unsafe for items such as volatile liquids,
cleaners or aerosol sprays.
• NEVER leave any items, especially plastic items, on the
cooktop. The hot air from the vent may ignite flammable
kems melt or soften plastics, or increase pressure in
closed containers causing them to burst
NEVER allow aluminum foil. meat probes or any other
metal obiect, other than a pan on a surface element, to
...............................
5
Coi E ement Surface
° Cban cooktop after each use.
° Wipe acidic or sugary spills as soon as the cooktop
has coobd as these spills may discobr or etch the
porcelain.
To protect drip bowl finish:
° To bssen discobradon and crazing, avoid using high
heat for bng periods.
° Do not use oversized cookware. PansshouM not
extend more than 1-2 inches beyond the dement.
° When home canning or cooking with big pots, use
the Canning Ebment [Modal CE1}.Contact your
dealer for details or caii 1-877-232-6771 USA
or 1-800-688-8408 Canada to order.
, Clean frequently. (See page 19.}
Coil Dements
, When an element is on, itwill cycle on and off to maintain the
heat setting.
° Coil dements are self-cleaning. Do not immerse in water.
To remove: When cool, raise ele-
menL Carefully pull out and away
from receptacle.
To replace: Insert dement ter-
minals into receptacle. Guide the
dement into place. Pressdown on
the outer edge of element until it
sits level on drip bowl
TERMINALS
Drip BowRs
The drip bowls under each surface element catch boilovers and
mustalways be used. Absence of drip bowls during cooking may
damage wiring.
To prevent the risk of electric shock or fire, never line drip bowls
with aluminum foil
Drip bowls wiii discolor {blue/gold stains} or craze over time if
overheated. This discoloration or crazing is permanent. This wiii
not affect cooking performance.
6
Manua C ean Oven ControJ
(select models}
BAKE
TIMER CLOCK CANCEL ....
A B
NOTE: The dispDy wiil show 12:00when the appliance is first connected to power or if power is interrupted. The Bake and Broil
indicators Hightwhen function is pressed.
A
B
D
E
F
Bake
BroiH
Timer
Clock
CANCEL
Aor_'
Use for baking and roasting.
Use for broiling and top browning.
Sets timer.
Use to set time-of-day clock.
Cancels all operations except timer
and clock.
Enters or changes time, oven
temperature. Sets HI or LO broil
Using the Touchpads
Pressthe desired pad.
Pressthe A or V pad to enter time or temperature.
° A beep will sound each time a function pad ispressed. There
is no beep for the A or V pad.
° A double beep wiii sound if a programming error occurs.
Note: Four seconds after pressing the A or V pad, the
time or temperature will automatically be entered. Ifmore
than 30 seconds elapse between touching a function pad
and the A or V pad, the function will be canceled and the
display will return to the previous display.
Setting the CJock
1. Pressthe Clock pad.
° The clock time cannot be set if the control is pro-
grammed for a bake, broil or timing operation.
c D E F
2. Set the correct time of day using the A or V pads. If the
A or V pad is not pressed within 30 seconds, the program
will cancel Pressthe Clock pad and begin again.
Setting the Timer
The timer can be set from one minute 001} up to 99 hours
and 59 minutes (99:59}. Timewill be displayed in minutes and
not in seconds. THE TIMER DOES NOT OONTROL THE
OVEN.
1. Pressthe Timer pad.......
° 0:00wiii iight and the coion (:} wiii flash in TIMER
the display. ...........
2. Pressthe A or Y"pad until the desired time is .....
displayed.
, The timer will begin as soon as the time is set.
° The flashing colon indicates that a timing
operation is in progress. (The colon wiii not
flash if the time of day or oven temperature is
displayed.}
° Two short beeps signal the end of the operation. "0:00"
wiii appear in the display.
If desired, press the Clock pad and the time of day wiii
briefly reappear in the display during a timing operation.
If desired, press the Bake or Broil pads and the current
temperature setting wiii briefly reappear in the display
during a timing operation.
To cancel the timer operation:
Press and hold the Timer pad for several seconds.
Baking, Roasting and Broiling
For addKionaHbaking, roasting and broiling thnes and tips, see
"Cooking Made Simple" booHeL
Setting the Controls For Baking or Roasting:
1. Press Bake pad.
, 000 wHHHightand the Bake indicator Hight BAK[:
wHHflash in the dispHay.
, If you press the Bake pad and do not set an oven
temperature within 30 seconds, the program wHH
automatically cancel and the time of day will reappear
in the display.
2. Press the A or V pad until the desired oven ......................
temperature is displayed.
, The oven temperature can be set from 170°
to 550° R
350° will appear in the display when either
A or V pad is pressed once.
Press and tap the A or V pad to change the oven
temperature by 5° increments or press and hold
the A or V pad to change the oven temperature
by 10° increments.
1O0° or the actual oven temperature, whichever is
higher, will appear in the display when the oven turns
on,
, The temperature in the display will increase in 5°
increments until preset temperature is reached. A single
beep will sound when the oven is preheated.
, Allow 10 to 15minutes for the oven to preheat.
, To recall preset temperature during preheat, press the
Bake pad. The temperature will be displayed for three
seconds.
Setting the Controls For Broiling:
For best results, use pan designed for broiling.
1. Place broiler pan on recommended rack position. (See
2. Pressthe Broil pad. B!_OH....
3. Pressthe A pad to select Hi (high:) broil or the
4. Preheat broil element for three minutes. Broil with the oven
5. After broiling, press Cancel to turn the oven .................
chart on page 15.]
° "SEt" will light and the Broil indicator light
will flash in the display.
V pad to set Lo (Jew] broil.
° Select Hi broil for normal broiling.
° Select Lo broil for low temperature broiling to
avoid excessive browning of longer cooking
foods like poultry.
° If you do not select Hi or Lo Broil within 30 seconds, the
program will automatically cancel and the time of day
will reappear in the display.
door open to the first stop position (about 4 inches:).
off and remove the broiler pan from the oven.
The current time of day will reappear in the
display.
° To change oven temperatare during cooking, press
the Bake pad, then press the A or V pad until the
desired temperature is displayed.
, To change oven temperature during preheat, press
the Bake pad twice, then pressthe A or V pad until
the desired temperature is displayed.
3. Place food in the oven. Check food for aloneness at the
minimum cooking time.
4. At the end of cooking, press the Cancel pad
to turn the oven off and remove the food from
the oven.
The oven features an automatic shut-off. Ifthe oven is
left on for 12 hours it will automatically turn off and 000
will appear in the display. Press the Cancel pad and the
time of day will reappear in the display.
Oven Knob Control
(:select models)
Oven Temp Knob B,o,
The Oven Temp Knob is used to
select and mamtah the oven tem-
perature. Always turn this knob just to
the desired temperature. Do not turn
to a higher temperature and then back. 4oo
Setting the Control for Baking and Roasting:
1. Push in and turn Oven Temp knob to desired temperature.
Allow 10-15 minutes for preheating.
2. Place food in the center of oven. Check food for aloneness
at minimum time in recipe. Cook longer if necessary.
3. Remove food from the oven and turn the Oven Temp knob
to OFF.
500
OFF
Warm
350 300
Setting the Control for Broiling:
1. For best results, use a broiling pan. Place the broiler pan
on recommended rack position (seechart on page 15).
2. Turn OvenTemp knob to Broil or, for lower temperature
broiling, to 450° F.
Lower temperature broiling avoids excessive browning
of longer cooking foods such as poultry.
3. Preheat broil element for three minutes. Broil with the oven
door open to the first stop position (about 4 inches).
4. Check the aloneness by cutting a slit in the meat near the
center to check the color.
5. After broiling, turn the Oven Temp knob to OFF.Remove
the broiler pan from the oven.
Nete: Foradditional baking, roasting and broiling tips, see
"Cooking Made Simple" booklet.
9
Seff Clean Oven Control
(select models)
A B
BAKE
V
C
D
TIMER
........... HOLD
COOl@,
E
The control panel isdesigned for easein programming. Thedispiaywindow on thecontrol shows time of day, timer and ovenfunctions.
Control panel shown includes model specific features. (Styling may vary depending on modeL}
A
Broil
B
Bake
C
Aor_
L'Moreor Less}
D
Timer
Cook & Hold
Clean
G!
Delay
H
Clock
Keep Warm
CANCEL
Use for broiling and top browning.
Use for baking and roasting.
Enters or changes time, oven
temperature. Sets HI or LO broil
Sets timer.
Bakes for a preset time, then holds food
warm for 1hour.
Use to set self-clean cycle.
Programs the oven to start baking at
a later time.
Use to set time-of-day clock.
Use to keep cooked food warm in oven.
Cancels all operations except timer
and clock.
Using the Touchpads
Pressthe desired pad.
Pressthe A or _' pad to enter time or temperature.
° A beep wiii sound when any pad is touched.
° A double beep wiii sound if a programming error occurs.
Note: Four seconds after pressing the A or V pad, the
time or temperature will automatically be entered. If more
than 30 seconds elapse between touching a function pad
and the A or V pad, the function will be canceled and the
display will return to the previous display.
........................................ ............ KEEP
CLEAN DELAY CLOCK
F G H J
The clock can be set to display time in a 12-hour or 24-hour
format. The clock is set at the factory for the 12-hour format.
To change the clock to 24-hour format:
Pressand hold the CANCEL and Delay
pads for three seconds.
2.
Pressthe A or Y"pad to select 12
or 24 hour.
3.
Set the time of day following the
directions below.
To set the Clock:
1. Pressthe Clock pad.
° Time of day and the colon flash in the
display.
2. Pressthe A or V pad to set the time of day.
° Colon continues flashing.
3. Pressthe Clock pad again or wait four
seconds.
When electrical power is supplied or after a power
interruption, the last clock time before power was
interrupted wiii flash.
To recall the time of day when another time function is
showing, press the Clock pad.
Clock time cannot be changed when the oven has been
programmed for cook or clean Delay or Cook & Hold.
-- DELAY
CLOCK
10
To cancem the Clock display:
If you do not want the thne of day to dispiay:
Press and hoid the CANCEL and CHockpads .........
for three seconds. The time of day wiii
disappear from the dispiay
When the chockdispiay is cancelled, press
the CHockpad to brbfiy dispiay the time
of day.
-- CLOCK
To restore the Clock display:
Press and hoid the CANCEL and CHockpads for three sec-
onds. The time of day wiii reappear in the dispiay.
The timer can be set from one minute (00:01} up to 99 hours
and 59 minutes @9:59}.
The timer can be used independently of any other oven
activity. Itcan also be set while another oven function is
operating.
The Timer does not control the oven. It only controls a
beeper.
To set the Timer:
1.
Press the Timer pad. nMER
.0:00 iights in the dispiay.
, The coion flashes in the dispiay.
Press the A or V pad untii the
correct time appears in the dispiay.
, The coion wiii continue to flash.
3,
PressTimer pad again or wait four seconds.
° The colon continues flashing and the time begins
counting down.
° The last minute of the timer countdown wiii be displayed
as seconds.
4. At the end of the set time, one long beep wiii sound.
s¢_ ¸_¸ ,_
To cancel the Timer:
1. Press and hold the Timer pad for three seconds.
OR
2. Press the Timer pad and set the time to 00:00.
Locking the Controms
The touchpad controls can be locked for safety',cleaning, or
to prevent unwanted use. They will not function when locked.
If the oven is currently in use, the controls cannot be locked.
The current time of day will remain in the display when the
controls are locked.
To leek:
Press and hold the CANCEL and Cook &
Hold pads for three seconds.
LOCKflashes in the display.
To unmoek:
Press and hold the CANCEL and Cook & Hold
pads for three seconds.
LOCKdisappears from the display.
COOK&
HOLD
Fault Codes
BAKE or LOCK may flash rapidiy in the dispiay to aiert you if
there is an error or a problem. If BAKE or LOCKflash in the
display, press CANCEL pad. If BAKE or LOCK continue to
flash, disconnect power to the appliance. Wait a few minutes,
and then reconnect power. If the flashing still continues,
disconnect power to the appliance and call an authorized
servicer.
To set Bake:
1.
Pressthe Bake pad. BAKE
° "BAKE" wiii flash.
° 000 wiii iight in the display.
2. Select the oven temperature. The oven tempera-
ture can be set from 170° to 550°. Press or press
and hold the A or V" pads.
° 350°wiii iight when either pad is first pressed.
, Pressthe A pad to increase the temperature.
, Pressthe V pad to decrease the temperature.
3. Press Bake pad again or wait four seconds.
° BAKE will stop flashing and light in the display.
° 100° or the actual oven temperature wiii display. The
temperature will rise in 5° increments until the preset
temperature is reached.
4. Allow the oven to preheat for 8-15 minutes.
° When the set oven temperature is reached, one long
beep will sound.
° To recall the set temperature during preheat, press the
Bake pad.
5. Placefood in center of oven, allowing a minimum of two
inches between utensil and oven walls.
V
11
0. Checkcookingprogress.CookHongerifneeded.
7. Whencookingisfinished,pressCANCEL.
8. Removefoodfromtheoven.
Baking Notes:
To change oven temperature daring cooking, press
the Bake pad, then press the A or V pad untiHthe
desired temperature is dispHayed.
To change oven temperature during preheat, press
the Bake pad twice, then press the A or V pad untiH
the desired temperature is dispHayed.
If you forget to turn off the oven, it will automatically turn
off at the end of 12 hours. If you wish to deactivate this
feature, see page 14.
For additionaHbaking and roasting tips, see "Cooking
Made SimpW' booHet.
When the cooking time has eJapsed:
, Four beeps will sound.
, "BAKE" will turn off.
, "HOLD" and "WARM" will light.
, 170°will display.
After one hoar in HOLD WARM:
, "End" wiii display.
° The time of day reappears in the display.
TO canceJ Cook & Hold at any time:
Press the CANCEL pad. Remove food from oven.
Baking Differences Between Your OJd
and New Oven
It is normal to notice some baking time differences between a
new ovenand an old one. See"Adjusting the OvenTemperature"
on page 14.
Cook & HoJd
Cook & Hold allows you to bake for a preset amount of time,
followed by a one-hour Keep Warm cycle.
TO set Cook & Hemal: ............
1. Press the Cook & Hold pad. HOLD
° "BAKE" and "HOLD" flash.
, 000 lights in the display.
2. Select the oven temperature. The oven tempera- A
ture can be set from 170° to 550°- Pressor press
and hold the A or V pad.
° Press the A pad to increase the temperature. V
° Press the _' pad to decrease the temperature.
3. Press Cook & Hold again OR wait four seconds.
° "HOLD" flashes.
° 00:00flashes in the display.
Enter the amount of time you want to bake by pressing the
A or V pad. Bake time can be set from ten minutes
(00:10:)to 11 hours, 59 minutes (11:59}.
, "BAKE" and "HOLD" light in the display.
° The baking time wiil light in the display.
° The baking time wiil start counting down.
De ay Bake
as dairy products, pork, poultry, or seafood.
When using Belay, the oven begins to cook later in the day.
Set the amount of time that you want to delay before the oven
turns on and how long you want to cook. The oven begins to
heat at the selected time and cooks for the specified length of
time, then keeps food warm for up to one hour.
Delay time can be set from 10 minutes (00:10] to 11 hours, 59
To set a Demayed Baking cycle:
1. Pressthe Delay pad..........
° "DELAY" flashes. DEL_?f
, 00:00flashes in the display. '.............
2. Press the A or V pad to set the delay time.
While "DELAY" is still flashing:
3. Pressthe Cook & Hold pad.
, 000 lights in the display.
, "BAKE" and "HOLD" flash. ..........
4, Press A pad to set the baking temperature,
° 00:00and "HOLD" flash.
, "BAKE" stays lit.
COOH{&
12
5. Press A pad to set the baking time+
, The Dday time, "DELAY", "BAKE" and "HOLD" Hightin
the dispiay.
When the Delay time has expired:
, "DELAY" will turn off=
, Baking time isdispiayed=
, "BAKE" and "HOLD" are dispiayed=
To set a Delay when Cook & Hold has already
beea programmed:
1. Press the Delay pad. DELAY
° "DELAY" flashes. ............................
, 00:00appears .......
2. Press the A or V pad to set the dday time+
, After four seconds, "DELAY" will
stay Hitto remind you that a de.,layed
cooking cycle has been set. ........................
When the Delay time has expired
and the oven starts:
, The baking time will be dispiayed.
, "DELAY" will turn off=
, "BAKE" and "HOLD" will remain Hit=
To cancel:
Press the CANCEL pad...................................... .................
, AHtimed and untimed cooking functions will be
canceled+
, The time of day will reappear in the display.
Notes:
Do not use delayed baking for items that require a
preheated oven, such as cakes, cookies+and breads.
Do not use delayed baking if oven is already hot.
Keep Warm
For safely keeping foods warm or for warming breads and
plates+
To set Keep Warm:
1. Pressthe Keep Warm pad. Ii(EIIxCP
° "WARM" flashes. ...........
° 000 appears in the display.
Select the Keep Warm temperature. The Keep
Warm temperature can be set from 145° to 190°.
Pressor press and hold the A or V pad.
° 170° will light when either pad is first pressed.
, Press the A pad to increase the temperature.
° Pressthe V pad to decrease the temperature.
"WARM" and the temperature wiii be displayed while Keep
Warm is active.
To cancel Keep Warm:
1. Pressthe CANCEL pad.
2. Removefood from the oven.
Keep Warm Notes:
° Foroptimal food quality, oven cooked foods should be kept
warm for no longer than 1 to 2 hours.
° To keep foods from drying, cover looselywith foil or a lid.
° To warm dinner rolls:
- cover rolls loosely with foil and place in oven.
- press Keep Warm and A pads to set 170° F.
- warm for 12-15 minutes.
, To warm plates:
- place 2 stacks of up to four plates each in the oven.
- press Keep Warm and A pads to set 170° F.
- warm for five minutes, turn off the oven and leave plates
in the oven for 15 minutes more.
WAII_M
/¸.>¸¸¸%¸
13
- use only oven-safe plates, check with the manufacturer.
- do not set warm dishes on a cold surface as rapid
temperature changes could cause crazing or breakage.
Automatic Shut-Off/Sabbath
Mode
The oven will automatically turn off after 12 hours if you
accidentally Heaveit on. This safety' feature can be turned off.
TO cancel the 12-hour shut-off and run the
oven continuously for 72 hours:
1. Set the oven to bake Cseepage 11}....................
2. Press and hoid the CHockpad for five seconds. C_OCK
, SAb wifl be dispiayed and flash for five seconds.
, SAb wifl then be dispiayed condnuousiy until turned off
or until the 72-hour time limit is reached.
, "BAKE" will also be displayed if a bake cycle is in use
while the oven is in Sabbath Mode.
All other functions EXCEPTBAKE {Timer. Keep Warm.
Clean, etc.} are locked out during the Sabbath Mode.
To cancel Bake when in Sabbath Mode:
Press CANCEL. ................
, "BAKE" will turn off in the display.
, No beeps will sound.
To cancel the Sabbath Mode:
1. Press the Clock pad for five seconds.
OR
2. After 72 hours, the Sabbath Mode will end.
, SAb will flash for five seconds.
Adjusting the Oven Temperature
Oven temperatures are carefully tested for accuracy at the
factory. It is normal to notice some baking or browning
differences between a new oven and an old one= As ranges
get older, the oven temperature can shift.
You may adjust the oven temperature if you think the oven is
not baking or browning correctly. To decide how much to
change the temperature, set the temperature 25° higher or
lower than your recipe recommends, then bake. The results
of the "test" should give you an idea of how much to adjust
the temperature=
To adjust the oven temperature:
1. Press Bake.
2.
Enter 550° by pressing the A pad.
3.
Pressand hold the Bake pad for several
seconds or until 0° appears in the display.
If the oven temperature was previously adjusted, the
change wiii be displayed. Forexample, if the oven tem-
perature was reduced by 15° the display wiii show "-15 °''.
Pressthe A or V pad to adjust the temperature.
Eachtime a pad is pressed, the temperature changes by
5°. The oven temperature can be increased or decreased
by 5° to 35°.
The time of day will automatically reappear in the display.
You do not need to readjust the oven temperature if there
is a power failure or interruption. Broiling and cleaning
temperatures cannot be adjusted.
BAKE
, The time of day will return to the display.
Sabbath Mode Notes:
, Sabbath Mode can be turned on at any time with or
without the oven on.
° Sabbath Mode cannot be turned on if the touchpads are
locked out or when the door is locked.
, If the oven is baking when Sabbath Mode is set. "BAKE"
will go out at the end of the baking cycle. There will be
no audible beeps.
, When the Sabbath Mode is started, no preheat beep wiii
sound.
, Aii prompts, messages and beeps are deactivated when
Sabbath Mode is active.
, Pressing CANCELwiii cancel a Bake cycle, however the
controi wiii stay in the Sabbath Mode.
° If power faiis, the oven wiii power up in Sabbath Mode with
72 hours remaining and no cycle active.
14
To set Broih
1. Press the Broil pad.
" "BROIL" flashes.
° SETis dispiayed.
2. Press the A pad to set HI broii or press the V pad to set
LO broil
° HI or LO wiii be dispiayed.
° Seiect HIbroii (550° F}for normai broiiing. Seiect
LO broii (450° F])for How-temperature broiiing of ionger
cooking foods such as pouitry.
3. After four seconds, the oven wiii start.
° "BROIL" wiii remain Hit.
4. For optimum browning, preheat broii eiement for 3-4
minutes before adding food.
5. Piace food in the oven. Leave oven door open about four
inches (the first stop]).
BRQ_....
6. Turn meat once about haifway through cooking.
7. When food is cooked, press the CANCEL pad.
Remove food and broiier pan from the oven.
, The time of day wiii reappear in the
dispiay.
Broil Notes:
, Forbest results when broiling, use a pan designed for
broiiing.
, Expect broi[ times to increase and browning to be
siightiy [ighter if appiiance is instaiied on a 208-voit
circuit.
, HI is used for most broiling. Use LO broil when broiling
longer cooking foods. The lower temperature allows
food to cook to the well done stage without excessive
browning.
, Broil times may be longer when the lower broiling
temperature is selected.
, Foradditional broiling tips and temperatures, refer to the
"Cooking Made Simple" bookleL
Broiling Chart
I j
FOODS POSiTiON + , DONENESS COOK TiME
Beef
Steak, 1" thick
Hamburgers, 3/4" thick
Pork
Bacon
Chops, 1"
Ham - precooked slice, 1/2" thick
Poamtry
Chicken Pieces
Seafood
Fish Steaks, buttered, 1" thick
Fillets
* The top rack position is #5.
Note: This chart is a suggested guide. The times may vary with the food being cooked.
4
4
4
4
4
4
3 or 4 Weii Done 28 - 38 minutes
Medium
Weii Done
Weii Done
Weii Done
Weii Done
Warm
Flaky
Flaky
15 - 18 minutes
19 - 23 minutes
15 - 18 minutes
6 - 10 minutes
22 - 26 minutes
8 - 12 minutes
LO Broii
10 - 15 minutes
8 - 12 minutes
15
Oven Vent
When the oven is in use, the area near the vent may become
hot enough to cause burns. Never block the vent opening.
OVEN VENT
/
Be sure the drip bow[ in the vent location
has a hole in the center. Do not cover
the drip bowHwith aHuminum fo&
OVEN VENT
OPENING
Oven Light
Press the Oven Light switch on the controH pand to
turn the oven Highton and off.
oven Hght
Oven Bottom
Protect oven bottom against spiHHovers,especiaHHyacidic or
sugary spiHHs,as they may discoHorthe porceHainenamel Use
the correct pan size to avoid spiHHoversand boiHovers.Do not
place utensils or aluminum foil directly on the oven
bottom.
To replace:
1. Place rack on the rack support in the oven
2. Tilt the front end up slightly. Slide rack back until it clears
the lock-stop position.
3. Lower front and slide back into the oven.
Do not cover an entire rack with aluminum foil or place foil
on the oven bottom. Raking results will be affected and
damage may occur to the oven bottom.
Rack Positions
RACK 5 (highest
position): Used for
toasting bread or
broiling thin, non-fatty
foods.
RACK 4: Used for
most broiling.
RACK 3: Used for most
baked goods on a
cookie sheet or jelly roll pan, layer cakes, fruit pies, or frozen
convenience foods.
RACK 2: Used for roasting small cuts of meal casseroles,
baking loaves of bread, bundt cakes or custard pies.
RACK 1: Used for roasting large cuts of meat and poultry,
frozen pies, dessert souffles or angel food cake.
MULTIPLE RACK COOKING:
Two rack: Use rack positions 2 and 4, or and 4,
5
__4
--3
__2
--!
/
Oven Racks
° DOnot attempt to change the rack position when the oven
is hot.
. Do nut use the oven for storing food or cookware,
The oven has two racks. All racks are designed with a lock-
stop edge.
To remove:
1. Pull rack straight out until it
stops at the lock-stop posi-
tion.
2, Lift up on the front of the rack
and pull out,
Haft Rack Accessory
A half rack, to increase oven capac-
ity, isavailable as an accessory'. Itfits
in the left, upper portion of the oven
and provides space for a vegetable
dish when a large roaster is on the
lower rack. Contact your dealer for
the "HALFRACK" Accessory Kit
or call 1-877-232-8771 USA or
1-800-888-8408 Canada.
16
Se f-C ean Oven (select models}
Note: For manuai dean oven, see page 20. 1
• It is normal for parts of the range to become hot duripg a
self-dean cycle,
• To prevent personal injur_ and damage to the oven door
do not attempt to open door when "LOCK" is displayed,
o Avoid touching cooktop door. window or oven vent area
Do not use commercial oven cleaners on the oven finish
or around any part of the oven. The} wiii damage the
finish or parts.
6. Wipe up sugary and acidic spiiiovers such as sweet
potatoes, tomato, or miik-based sauces. PorceHainename]
is acid-resbtant, not acid-proofi The porceiain finish may
discoior if acidic spiiis are not wiped up before a seif-ciean
cycie.
To set Self-Clean:
Note: Oven temperature must be bellow 400° Fto program
a dean cycie.
1. Close the oven door.
2. Move door lock lever right to the locked position.
The self-clean cycle uses above-normal cooking temperatures
to automatically clean the oven interior. Do not force the oven
door or lock lever open. This mayresult in exposure to high
temperatures and be a burn hazard.
It is normal for flare-ups, smoking, or flaming to occur during
cleaning if the oven is heavily soiled. It is better to clean the
oven regularly rather than to wait until there is a heavy build-
up of soii in the oven.
During the cleaning process, the kitchen should be well
ventilated to get rid of normal odors associated with cleaning.
Before Seff-CJeaning
1. Turn off the oven light before cleaning. The light may burn
2. Remove broiler pan, all pans, and oven racks from the
oven. The oven racks wiii discolor and may not slide easily
after a self-clean cycle if they are not removed.
3. Clean oven frame, door frame, area outside of gasket, and
around the opening in the door gasket with a nonabrasive
cleaner such as Bon Ami* or detergent and water. The
self-cleaning process does not
clean these areas. They should be
cleaned to prevent soil from baking
on during the clean cycle. (The
gasket is the seal around the oven
door and window}.
a. To prevent damage, do not clean or
rub the gasket around the oven
door. The gasket is designed to seal in heat during the
clean cycle.
5. Wipe up excess grease or spillovers from the oven bottom.
This prevents excessive smoking, flare-ups or flaming
during the clean cycle.
3. Press the Clean pad. CLEAN
, "CLEAN" flashes in the display. ................
If the door is not closed, beeps wiii sound and "DOOR" wiii
display. If the door is not closed within 45 seconds, the
self-cleaning operation wiii be canceled and the display
will return to the time of day.
4. Press the A or Y pad...........................
° "CL-M" (Medium Soil, 3 hours} is displayed.
5. Press the A or V pad to scroii through the
self-cleaning settings.
CL-H" (Heavy Soil, 4 hours} ..................
CL-M" (Medium soil, 3 hours}
CL-L" (Light Soil, 2 hours}
Choosing the soil level of the oven automatically programs
the self-cleaning time.
6. After four seconds, the oven will start cleaning.
° The cleaning time will start counting down in the display.
"LOCK" wiii appear in the display.
"CLEAN" wiii appear in the display.
To
Delay a SeJf-Ciean Cycle: ...........................
1.
Press the Delay pad. DELAY
° "DELAY" flashes.
00:00wiii appear in the display.
Press the A or V pad to set the amount of
time you want to delay the cycle. Delay time
can be set from ten minutes @0:10}to 11 hours,
59 minutes (11:59}.
eonto
* Brand names for cleaning products are registered trademarks of the respective manufacturers.
17
3. PresstheCleanpad.
, "CLEAN"wiiiflash. CLEAN
4. PresstheA orV pad. ,
, "CL-M"(MediumSoft,3hours}
isdisplayed.
5. PresstheA orV padtoscrollthroughthe
self-cleaningsettings.
CL-H"(HeavySoft,4hours}
CL-M"(Mediumsoft,3hours}
CL-L"(LightSoft,2hours}
Choosingthesoftleveloftheovenautomaticallyprograms
theself-cleaningtime.
6. Afterfourseconds,CLEAN,DELAYandLOCKwillappear
inthedisplaytoshowthattheovenissetforadelayed
cleanoperation.Thedelaytimeisdisplayed.
Jf the oven has already been set for a clean
cycle and you wish to set a delay:
1. Press the Delay pad. DELAY
, "DELAY" flashes...........
, 00:00will appear in the display.
2. Press the A or V pad to set the amount of
time you want to delay the cycle.
After four seconds, CLEAN, DELAY and LOCK
will appear in the display to show that the oven
is set for a delayed clean operation. The delay
time is displayed.
When the Self-Clean cycle starLs:
° "DELAY" wfl] turn off.
During the Seff-C_ean Cycle
When LOCK shows hi the dispiay, the door cannot be opened.
To prevent damage to the door, do not force the door open
when LOCK is displayed.
Smoke and Sin!!ms
You may see some smoke and smell an odor the first few
times the oven is cleaned. This is normal and will lessen in
time.
Smoke may also occur if the oven is heavily soiled or if a
broiler pan was left in the oven.
Sounds
As the oven heats,you may hear sounds of metal parts
expanding and contracting. This is normal and will not
damage the oven.
After Seff-C_eaning
About one hour after the end of the self-clean cycle, "LOCK"
will turn off. The door can then be opened. The door can then
be opened. Move door lock lever to the left to unlock.
Some soil may leave a light gray, powdery ash. Remove
it with a damp cloth. If soft remains after wiping, that means
the clean cycle was not long enough. The soft will be re-
moved during the next clean cycle.
if oven racks were left in the oven and do not slide
smoothly after a clean cycle, wipe racks and rack supports
with a small amount of vegetable oil to make them easier to
move.
Fine lines may appear in the porcelain because it went
through heating and cooling. This is normal and wiii not
affect performance.
A white discoloration may appear after cleaning if acidic
or sugary foods were not wiped up before the self-clean
cycle. This discoloration is normal and will not affect perfor-
mance.
, The clean time will appear in the display.
To cancem the Self-Clean cycle: .................................
Press the CANCEL pad.
° All words disappear from the display. .........................................
° All functions are canceled.
° The time of day appears in the display.
, If the oven door is left open, "DOOR" wiii flash in the
display and a signal will beep until the door is closed
and the Clean pad is pressed again.
, The oven door will be damaged if the oven door is
forced to open when "LOCK" is still displayed.
18
Cleaning Procedures
, Besur app a.ce a.pa ,areCooMb for .an.m ng
t !f a part !s rem°ved, besure it is correctly replaced.
PROCEDURE
Porcelain enamel is glass fused on metal and may crack or chip with misuse. It is acid resistant, not acid
Cooktop -
Porcelain Enamel
proof. All spillovers, especially acidic or sugar}, spillovers, should bewiped up immediately with a dry cloth.
, When cool, wash with soapy water, rinse and dry.
, Never wipe off awarm or hot surface with a damp cloth. This may cause cracking or chipping.
, Never use oven cleaners, abrasive or caustic cleaning agents on exterior finish of range.
Brand names are registered trademarks of the
respective manufacturers.
** To order call 1-877-232-6771 USAor
1-800-688-8408 Canaca.
Broiler Pan and
insert
Clock and
Control Pad
Area
Control Knobs
Drip Bowls -
Porcelain
(select models}
Drip Bowls =
Chrome/Painted
Enamel
(select models}
Never cover insert with aluminum foil as this prevents the fat from draining to the pan below.
° Place soapy cloth over insert and pan; let soak to loosen soil=
° Wash inwarm soapywater. Use scouring pad to remove stubborn soil
, Broiler pan and insert can be cleaned in dishwasher.
° To activate "Control Lock" for cleaning, see page 11.
° Wipe with adamp cloth and dry. Do not use abrasive cleaning agents as they mayscratch the finish.
° Glass cleaners may be used if sprayed on a cloth first. BO NOTspray directly on controlpad and
display area.
° Remove knobs in the OFF position by pulling forward.
, Wash, rinse and dry. Do not use abrasive cleaning agents as they may scratch the finish.
, Turn on each dement to be sure the knobs have been correctly replaced.
Porcelain may discolor or craze if overheated. This is normal and wiii not affect cooking performance.
, When cool, wash after each use, rinse and dr}, to prevent staining or discoloration. May be washed in the
dishwasher.
° To clean heavy soil, soak in hot sudsy water, then usea mild abrasive cleaner such as Soft Scrub* and a
plastic scouring pad.
° Forburned on soil, remove from range, place on newspapers and carefully spray with commercial oven
cleaner. {Do not spray surrounding surfaces.} Placein plastic bagand allow tosoak several hours. Wearing
rubber gloves, remove from bag, wash, rinse and dr},.
, When cool, wash after each use, rinse and dry to prevent staining or discoloration.
° To clean heavy soil, soak in hot sudsy water, then use a mild abrasive cleaner such as Soft Scrub* and
a plastic scouring pad. Do not use abrasive cleaning agents.
Oven Window
and Door - Glass
(select models}
, Avoid using excessive amounts of water which may seep under or behind glass causing staining.
° Wash with soapand water. Rinsewith clear water and dry. Glasscleaner can be used ifsprayed on a cloth
first.
° Do not useabrasive materials such asscouring pads,steel wool or powdered cleaners asthey wiii scratch
glass.
19
PART PROCEDURE
Oven interior Seif-Dleam
, Follow hstmctions on page 17-18 to set a self-clean cycle=
Manual Clean:
° CHeanfrequentHyusing miHdabrasive cleaners and a pHasticpad.
, Do not use metallic scouring pads because they will scratch the surface.
° When using commerciaHoven cleaners follow the manufacturer's instructions.
, Wipe up acidic spills (tomato or milk based foods:)as soon as possible with soap and water. If the spill
is not wiped up, it may discolor the porcelain.
To make cleaning easier, remove the oven door, if desired. (See Maintenance section on
page 21,_
Oven Racks , Clean with soapy water.
° Remove stubborn soil with cleansing powder or soap-filled scouring pad. Rinse and dr},.
, Racks will permanently discolor and may not slide smoothly if left in the oven during a self-clean
operation. If this occurs, wipe the rack edge and rack support with a small amount of vegetable oil to
restore ease of movement, then wipe off excess oil.
Stainless Steel ° DO NOT USEANY CLEANING PRODUCT CONTAINING CHLORINE BLEACH.
(select modds_) ° DO NOT USE ABRASIVE OR ORANGE CLEANERS.
° ALWAYS WIPE WITH THE GRAIN WHEN CLEANING.
. Daily Cleaning/LigM Soil -- Wipe with one ofthe following - soapywater, white vinegar/water sohJtion,
Formula 409 Glass and Surface Cleaner* or a similar glass cleaner - using a sponge or soft cloth. Rinse
and dry. To polish and help prevent fingerprints, follow with Stainless Steel Magic Spray (Part No.
20000008)**.
° Moderate/Heavy Soil -- Wipe with one of the following -Bon Ami, Smart Cleanser, or Soft Scrub* -
using a damp sponge or soft cloth. Rinseand dry'.Stubborn soils may be removed with a damp multi-
purpose Scotch-Brite* pad; rub evenlywith the grain. Rinse and dr},.To restore luster and remove streaks,
follow with Stainless Steel Magic Spray_,
, Discoloration -- Using a damp sponge or soft cloth, wipe with Cameo Stainless Steel Cleaner*. Rinse
immediately and dry,.To remove streaks and restore luster, follow with Stainless Steel Magic Spray_,
Oven Door (select , When cool, wash with warm soapy water, rinse and dry'. Neverwipe a warm or hot surface with a damp
models:), Storage cloth as this may damage the surface and may cause a steam burn.
Drawer, Door ° Forstubborn soil, use mildly abrasive cleaning agents such as baking soda pasteor Bon AmL* Do not use
Handle, Side abrasive, caustic or harsh cleaning agents such assteel woo] pads or oven cleaners. These products wi]]
Panels - Painted scratch or permanently damage the surface.
Enamel NOTE: Use a dry towel or cloth to wipe up spills, especially acidic or sugary spills. Surface may
discolor or dull if soil is not immediately removed. This is especially important for white surfaces.
* Brand names for cleaning products are registered trademarks of the respective manufacturers.
*_To order direct, call 1-877-232-8771 USA or 1-800-888-8408 Canada.
20
Oven Door
Oven Window (select models}
To protect the oven door window:
o Do net place excessiveweight on or stand on an open
oven door. This could cause the range to tip over. break
Do not attempt to open or close door or operate oven until
door is properly replaced.
Never place fingers between hinge and front oven frame.
Hinge arms are spnng mounted. If accidentally hit. the
hinge will slam shut against oven frame and could injure
To remove:
1. When cool, open the oven door to
the first stop position (opened
about four inches}.
2. Grasp door at each side. Do not
use the door handle to lift door.
3. Lift up evenly until door clears
hinge arms.
To replace:
1. Grasp door at each side.
2. Align slots in the door with the hinge arms on the range.
3. Slide the door down onto the hinge arms until the door is
completely seated on the hinges. Push down on the top
corners of the door to completely seat door on hinges.
Door should not appear crooked.
Note: The oven door on a new range may feel "spongy"
when it is closed. This is normal and will decrease with use.
1. Do not use abrasive cleaning agents such as steel wool
scouring pads or powdered cleansers as they may scratch
the glass.
2. Do not hit the glass with pots, pans, furniture, toys, or other
objects.
3. Do not close the oven door until the oven racks are in
place.
Scratching, hitting, jarring or stressing the glass may weaken
its structure causing an increased risk of breakage at a later
date.
i Disconnect p0wei to range be[ore replacing l!ght bu!b.
when replacing bulb,
o Do not touch hot bulb with adamp cloth asthis may cause
the bulb to break.
To Replace Oven Light Bulb:
1. When oven is cool, hold bulb cover in place, then slide wire
retainer off cover.
Note: Bulb cover wiii fail if not held in place while removing
wire retainer.
2. Remove bulb cover and light bulb. BuL_covER
3. Replace with a @-watt appli-
ance bulb.
4. Replace bulb cover and se-
cure with wire retainer.
5. Reconnect power to range.
Resetclock.
21
RETAINER
Leve ing Legs
Be suEethe ant!-tip bracket secures one of the rear
from accidentafly tipping,
Storage [}rawer
Do not store phstic, paper products, food or flammab!e
materials in this drawer. The drawer may become too warm
for these items when the oven is in use.
To replace:
1. Fit the ends of the drawer glides into the rails in the range.
2. Lift up the front of the drawer and gently push in to the first
stop position.
3. Lift drawer up again and push until drawer is closed.
Convenience Outlet
(Canadian models only}
The convenience outlet is located on
the lower left side of the backguard.
Be sure appliance cords do not rest
on or near the surface element. If the
surface element is turned on, the
cord and outlet wiii be damaged.
The convenience outlet circuit
breaker may trip if the small appli-
ance plugged into it exceeds 10
amps. To reset the circuit breaker,
press the switch located on the
lower edge of the backguard.
CIRCUIT BREAKER
The storage drawer can be removed to allow you to clean under
the range.
To remove:
1. Empty drawer and puff out to the first stop position.
2. Lift up the front of the drawer.
3. Puffout to the second stop position.
a. Grasp sides and lift drawer top up and out.
22
PROBLEM SOLUTION
For most concerns, try these first. , Check if oven controb have been properiy set.
° Check to be sure piug is secumiy inserted into receptacle.
° Check or re-set circuit breaker. Check or repiace fuse.
, Check power suppiy.
Part or atomof appmiance does not
work.
Clock, indicator words, and/or
lights operate but oven does
not heat.
Baking resumts are not as
expected or differ from
previous oven.
Food is not broiming properly or
smokes excessively.
° Check if surface and/or oven controb have been properiy set. See pages 5-16=
° Check if oven door is unbcked after serif-dean cycb. Seepage 18.
° Check if oven is set for a ddayed cook or clean program. See pages 12& 17.
° Check if Control Lock is activated=See page 11.
° Check if control is in Sabbath Mode. See page 14.
° Oven may be set for a Cook & Hold or delay function.
° The Control Lock may have been set. Seepage 11.
° Make sure the oven vent has not been blocked. See page 16for location.
° Check to make sure range is level.
° Temperatures often var},'between a new oven and an old one.As ovens age,the oven
temperature often "drifts" and may become hotter or cooler. See page 14for
instructions on adjusting the oven temperature (select models[). NOTE: It is not
recommended to adjust the temperature if only one or two recipes are in question.
° See "Cooking Made Simple" booklet for more information on bakeware and
baking.
° Check oven rack positions. Food may be too close to dement.
, Broil dement was not preheated.
° Aluminum foil was incorrectly used. Never line the broiler insert with foil.
° Oven door was closed during broiling. Leavethe door open to the first stop position
@bout 4 inches}.
, Trim excess fat from meat before broiling.
° A soiled broiler pan was used.
, Voltage in house may be low.
Oven wimmnot semf-cmean
(select models).
Oven did not cmeanproperly
(semect modems).
Oven door will not unlock after
self-clean cycle (select models).
, Check to make sure the cycle is not set for a delayed start. See page 17.
° Check if door is closed.
° Check if control is in Sabbath Mode. See page 14.
° Oven may be over 400° F.Oven temperature must be below 400° Fto program a
clean cycle.
° Longer cleaning time may be needed.
° Excessivespillovers, especially sugar}, and/or acidic foods, were not removed prior
to the self-clean cycle.
, Oven interior is still hot. Allow about one hour for the oven to cool after the
completion of a self-clean cycle. The door can be opened when the LOCK is not
displayed.
° The control and door may be locked. See page 11.
cont.
23