* TO PREVENT FIRE OR SHOCK HAZARD. DO NOT EXPOSE THIS APPLIANCE TO RAINOR MOISTURE.
*THIS APPLIANCE SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING WATER AND THAT NO
OBJECT FILLED WITH LIQUIDS SUCH AS VASES SHALL BE PLACED ON APPARATUS.
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other
prong. The wide blade or the third prong are provided for your safety
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
) Only use attachments/accessories specified by the manufacturer.
11
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid
injury from tip-over
13 ) Unplug this apparatus during lightning storms or when unused for long periods of time.
14 ) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
.
, such as power-supply cord or plug is damaged, liquid has been spilled or objects
. A grounding type plug has two blades and a third grounding
. If the provided plug does not
S3125A
1
Safety instructions/Features
www.karaoke.at
15) Grounding or Polarization This product may be equipped with a polarized alternating current line plug
(a plug having one blade wider than the other). This plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug.
If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat
the safety purpose of the polarized plug.
entilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable
16) V
operation of the product and to protect it from overheating, and these openings must not be blocked
or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other
similar surface. This product should not be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer's instructions have been adhered to.
17) The MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall
remain readily operable.
Class 1 Laser Product
CAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
PRODUCT COMPLIES WITH DHHS RULE 21 CFR SUBCHAPTER J IN EFFECT AT DATE
OF MANUFACTURE.
CAUTION: INVISIBLE LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM.
Class II equipment symbol
This symbol indicates that the unit has
a double insulation system
Features
-Complete karaoke system supports DVD,DVD-R,
DVD-RW,VCD,CDG,MP3,MP4,PHOTO-CD,CD,CD-R and CD-RW
-Support USB/SD Card,MP3 record function to let you record
your own vocal to the USB/SD Card(USB/SD Card not included)
-Inputs:Guitar and Keyboard inputs/two MIC inputs/three RCA A/V inputs
-Outputs:Two RCA A/V /Balanced audio
one stereo 1/4 inch audio pre-out /5.1CH audio out
-7-band equalizer
-Digital echo with repeat and delay controls
-Digital key control
-Remote control
-50W+50W music power(peak to peak)
-AC 1
15V/230V and PAL/NTSC compatible for worldwide use
2
Specifications and package Contents
www.karaoke.at
Specifications
● AC Input Voltage
● Audio Output Power
● AV1 audio input sensitivity
● Video input sensitivity
● Microphone Input Sensitivity
● Keyboard/Guitar Input Sensitivity
● Video Output Level
● Audio Output Level
● S/N Ratio
● Dimension
● Weight
AC 115V 60Hz/AC 230V 50Hz
100 W (peak to peak)
500 mV
1 V (peak to peak)
8 mV
8 mV
1 V (peak to peak)
1000 mV
90 dB
18.3" x 12.8" x 16.5" (L x W x H)
35.4 lbs
Package Contents
Items Quantities
BOOMER Unit (1)
A/V RCA Cable (1)
Remote Control (1)
AC Power Cord (1)
AAA Batteries (2
)
A/V RCA Cable (1)
BOOMER
BOOMER Unit (1)
AC Power Cord (1)
Note
If you find that any of the items mentioned above are missing
from the box, please contact MadBoy before proceeding.
AAA Batteries (2)
3
COPY MP3
REC
BOOMER
Remote Control (1)
Basic Connections
TV
www.karaoke.at
Since the BOOMER contains built-in power amplifiers, speakers, DVD/CDG/CD player, USB player, and SD
card player, the BOOMER can be used as a self-contained sound system. However, the BOOMER contains
various audio video outputs to allow the BOOMER to be connected to multiple TV sets, external sound
systems, and/or multiple sound effect devices. The following content demonstrates the procedures for
connecting the BOOMER to the AC outlet and other audio video devices.
Connecting to the AC outlet
To power the BOOMER
230
VOLTAGE SELECTOR
What you will need
●AC power cord (included)
●Surge-protector (recommended) or a power outlet
Note: Before turning on the power make sure the red voltage selector [Fig. A] under
the AC input is set to the proper voltage. It should be set to 115V for North America
and 230V for most European countries. Make sure you know the proper voltage for
your region before turning on the BOOMER.
1.Connect the AC end of the power cord into the AC input on the rear panel of the BOOMER
2.Connect the other end to a surge-protector or available power outlet
Connecting to a TV / video monitor with a RCA input
What you will need
●1 RCA-style video cable (included)
●TV / video monitor with a RCA video input
Connect one end of the RCA video cable to the yellow Video Out on the rear panel of the BOOMER.
1.
2.The BOOMER has two RCA-type VIDEO OUTPUT jacks for connecting to TVs or monitor devices.
Both VIDEO OUTPUTS can be connected simultaneously
3.Connect the other end of the RCA video cable to the Video Input on a TV / video monitor
[Fig. A]
.
TV
4
Basic Connections
www.karaoke.at
Connecting to an audio mixer or TV with RCA audio inputs
●using three ¼-inch stereo audio cables (not included).
●using one audio amplifier with XLR audio inputs.
●using one audio amplifier with ¼-inch audio inputs.
●using 1 audio mixer or TV with RCA audio inputs
1.
AUDIO OUTPUT 1 & 2 CONNECTIONS:
●Connect one end of the L/R (red & white) RCA cable to the red
and white audio outputs labeled
AUDIO OUTPUT 1 & 2 on the rear panel of the BOOMER.
●Connect the other end of the L/R (red & white) RCA cable to
the audio input on an audio mixer or TV
.
2.BALANCED AUDIO OUTPUT CONNECTIONS:
●Connect one end of the XLR cables to the left and right BALANCED AUDIO OUTPUT jacks on the BOOMER.
●Connect one end of the XLR cables to the left and right AUDIO/LINE/AUX INPUT jacks on the external device.
3.¼ INCH PRE-OUT CONNECTIONS:
●Connect one end of the ¼ inch audio cables to the left and right PRE-OUT jacks on the BOOMER.
●Connect one end of the ¼ inch audio cables to the left and right AUDIO/LINE/AUX INPUT jacks on
the external device.
PRE-OUT
4.CONNECTING EFFECTS USING THE EFFECT INSERT:
1.Connect one end of the ¼ inch stereo audio cables to the GUITAR EFFECT, KEYBOARD EFFECT
MIC EFFECT inserts on the rear panel of the BOOMER.
2.Connect the other end of the ¼ inch stereo audio cables to the sound effect device.
3.By using the built-in EFFECT INSERT you can add external effects to vocals and/or guitar or keyboard or
microphone without compromising the quality of the original signal.
, or
5
DVD Output Connections
www.karaoke.at
The insert is a break point in the input channel signal path, It allows the signal to be taken out from this BOOMER,
through an external equipment such as a Limiter,Compressor,Equalizer, Effector,and then back to the BOOMER,
the input jack can be used with ¼ inch phone jack,the signal will be send out through TIP of the ¼ inch phone
jack and back to the BOOMER through RING of the ¼ inch phone jack.
DVD OUTPUT CONNECTIONS
1.Connecting to a Dolby Pro logic amplifier
The BOOMER allows DVD audio output for 5.1 or 7.1 configurations.
With a 5.1 amplifier
ML, CEN, SL, MR, SW and SR outputs on the BOOMER. Connect the plug from the other side of each cable to
the corresponding ML, CEN, SL, MR, SW and SR inputs on your 5.1 amplifier
A 7.1 Pro Logic configuration requires 2 additional RCA cables to be connected from the FL and FR outputs of
the BOOMER to your 7.1 Amplifier.
, you will need six RCA patch cables. Connect the plug from one side of each cable to the
.
2.Connecting to a TV with component video
Using 3 appropriate component video cables (usually color coded red, blue and green), connect a set of plugs
to the COMPONENT VIDEO OUT jacks (Y-U/Pb-V/Pr) on the BOOMER and plug the other set of plugs to the
COMPONENT VIDEO IN jacks (Y
jacks may be labeled differently (i.e. Pr/Pb/Y or Cr/Cb/Y or R-Y/B-Y/Y etc.). You will need to press the MODE
button on the remote control to toggle between YUV for Component Video, and S-Video. You can only use the
MODE button when there is no disc inserted in the disc tray
-U/Pb-V/Pr) on your television. On some TVs, the component video input
.
6
DVD Output Connections
www.karaoke.at
3.Connecting to a DTS receiver/decoder
Using either a RCA-ended COAXIAL cable suited for digital audio use or an OPTICAL cable, connect one
end to the appropriate jack on the BOOMER (COAXIAL or OPTICAL) and the other end to the appropriate jack
(COAXIAL or OPTICAL). If you have both coaxial and optical inputs on your DTS decoder/receiver
recommended to use an optical connection as those cables eliminate the possibility of EMI (electromagnetic
interference). has 5.1 or 7.1 channel RCA inputs, you can use the 5.1 or 7.1 channel output jacks on
the BOOMER.
, it is
AV input connections
What you will need
●3 RCA-style A/V cable (included)
●2 A/V output Device
1.Connect one end of the 3 RCA-style A/V cable to the A/V VIDEO/L/R input labeled AV1/AV2/ AV3 on the front
panel of the BOOMER.
2.Connect the other end of the 3 RCA-style A/V cable to the A/V VIDEO/L/R output on an A/V output Device.
7
Loading...
+ 22 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.