Mackie ONYX400F User Manual
FireWire Connection
The Onyx 400F is equipped with two 6-pin FireWire
connectors and comes with a 6-pin to 6-pin FireWire
cable. This works with Macintosh laptops and desktops,
and most PC desktops with a built-in FireWire connector or with a PCI or PCMCIA FireWire card added.
Many laptop PCs have a 4-pin FireWire connector. If
this is the case, you will need to purchase a 6-pin to 4pin FireWire adapter cable. These are readily available
at computer stores or online.
2 4 6
Owner’s Manual
1 3 5
6-pin Male FireWire
6-pin FireWire Wiring:
Pin 1 = Power
Pin 2 = Ground
Pin 3 = TPB–
Pin 4 = TPB+
1 2 3 4
4-pin Male FireWire
4-pin FireWire Wiring:
Pin 1 = TPB–
Pin 2 = TPB+
Pin 3 = TPA–
Pin 4 = TPA+
Pin 5 = TPA–
Pin 6 = TPA+
Appendix C: Technical Info
Onyx 400F Specifi cations
Frequency Response
Mic Input to Line Output (Gain @ unity):
@48 kHz
+0, –3 dB, 10 Hz to 24 kHz
@96 kHz
+0, –3 dB, 10 Hz to 48 kHz
@192 kHz
+0, –3 dB, 10 Hz to 96 kHz
Mic Input to Digital Output (S/PDIF, 192 kHz sample rate):
+0, –3 dB, 10 Hz to 96 kHz
Distortion (THD & IMD)
Mic Input to Line Output (@ +4 dBu output):
1 kHz input
Mic Input to Digital Output (S/PDIF, 48 kHz sample rate):
THD+N: < 0.001%, 20 Hz to 20 kHz BW,
10mV rms input, gain at –1 dB FS output
THD+N: < 0.003%, 20 Hz to 20 kHz BW,
@ +4 dBu, preamp at unity gain
Dynamic Range
>107 dB (Mic In to Line Out)
Noise
Signal-to-Noise:
Equivalent Input Noise (E.I.N.), 20 Hz to 20 kHz Bandwidth,
150Ω source impedance:
–129 dBu @ +60 dB gain
Common Mode Rejection Ratio (CMRR)
Mic In: >60 dB @ 1 kHz, Gain @ maximum
Crosstalk
Mic Input to Line Output:
< –100 dB @ 1 kHz, +10 dBu signal on adjacent
input, 150Ω source impedance
Input Gain Control Range
Mic In: 0 dB to +60 dB
Line In: –20 dB to + 40 dB
>87 dB (ref. +4 dBu, Mic In to Line Out, Gain @ unity)
Owner’s Manual
31
Phantom Power
+48 VDC
Rated Output
Line: +4 dBu
Maximum Rated Output:
+24 dBu @ Balanced Line-Level Outputs
Input Impedance
Mic Input: 2.4 kΩ balanced
ONYX 400F
Inst Input: 1 MΩ
Line: 20 kΩ balanced, 10 kΩ unbalanced
Digital Output Connectors
One BNC connector for external word clock output
One RCA connector for S/PDIF output
One 5-pin DIN for MIDI output
DSP
TMS320C6713 Floating-Point Digital Signal Processor
operating at 225 MHz, delivering up to 1350 million
fl oating-point operations per second (MFLOPS),
1800 million instructions per second (MIPS), and
450 million multiply-accumulate operations per
second (MMACS)
Output Impedance
Line: 100 Ω balanced
Signal Level LEDs
–40 dB, –20 dB, –10 dB (normal operating level),
OL = 22 dBu
Sample Frequency Selections
44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz,
176.4 kHz, 192 kHz
Analog Input Connectors
Four balanced XLR/TRS mic/line inputs
Four balanced 1/4" TRS line inputs
Two 1/4" TS high-impedance instrument inputs
Analog Output Connectors
Eight balanced 1/4" TRS line-level outputs
Digital Input Connectors
One BNC connector for external word clock input
One RCA connector for S/PDIF input
One 5-pin DIN for MIDI input
Two 6-pin FireWire input/output
AC Power Requirements
Power Consumption: 20 watts
Universal AC Power Supply:
100 VAC – 240 VAC, 50-60 Hz
Physical Dimensions and Weight
Height: 1.75 in/44 mm
Width: 17.50 in/445 mm (main body of unit)
19.00 in/483 mm (with rack ears)
Depth: 7.63 in/194 mm (including front knobs and
rear BNC jack)
Weight: 5.6 lb/2.5 kg
LOUD Technologies Inc. is always striving to improve our products by incorporating new and improved materials, components,
and manufacturing methods. Therefore, we reserve the right to
change these specifi cations at any time without notice.
“Mackie.”, “Onyx,” and the “Running Man” are registered
trademarks of LOUD Technologies Inc. All other brand names
mentioned are trademarks or registered trademarks of their
respective holders, and are hereby acknowledged.
©2005 LOUD Technologies Inc. All Rights Reserved.
32
7.6 in/194 mm
1.75 in/
ONYX 400F
44 mm
(1 rack space)
17.5 in/445 mm
WEIGHT
5.6 lb/
2.5 kg
19.0 in/483 mm
4321
Loading...