Lynx L30POD, LPSGE-1, LSB1-1, LSB2-1, LSB2PC-1 Care & Use Manual
...
*, " - - " Ê , -
Care & Use of Your
Lynx Professional Grill
A Message to Our Customers…
Thank You for choosing LYNX as your new gas grill. With proper use and care, we’re confident that our product will provide years of trouble-free service. Careful attention has been put
into every detail of this grill and, by reading this entire manual before your first use, you will be
assured of maximum performance and enjoyment.
This manual also contains important safety tips and some hints for better grilling. Please keep it
in a convenient location so it will be available to answer any future questions. Should your LYNX
grill change ownership, please make sure that the new owner receives this manual.
We love to hear from our customers. Please feel free to contact us with any questions or problems, or to share a new recipe. Please include the model number of your grill in your correspondence. Thanks again for your purchase. Enjoy!
This manual covers the following 2008 Lynx products:
Installation, Care and Use
of Your Lynx Professional
Cooking Product
GRILL MODELS
L27 & L27F
L27R & L27FR
L30R & L30FR
L36R & L36FR
L42R & L42FR
PROSEAR MODELS
L30PSR & L30PSFR
L36PSR & L36PSFR
L42PSR & L42PSFR
L54PSR & L54PSFR
LPSGE
SIDE BURNER MODELS
LSB2PC
LSB1
LSB2
F O R O U T D O O R U S E O N LY
IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE
CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH. READ THIS MANUAL
THOROUGHLY BEFORE INSTALLATION, USE OR SERVICING OF THIS EQUIPMENT
C A L I F O R N I A P R O P O S I T I O N 6 5 WA R N I N G
The burning of gas cooking fuel generates some by-products, which are on the list of substances, which are
known by the State of California to cause cancer or reproductive harm. California law requires businesses to
warn customers of potential exposure to such substances. To minimize exposure to the substances, always
operate this unit according to the use and care instructions found in this manual. Be certain to provide
adequate ventilation when cooking. California Proposition 65 lists “Silica, crystalline” which is used in one of
the components of the IR burner, as an agent known to the state of California to cause cancer.
N O T E TO I N S TA L L E R
This manual must remain with grill. Check your local building codes for proper method of installation. In
the absence of local codes, this unit should be installed in accordance with National Fuel Gas Code No. ANSI
Z21.58D-2002 USA or CAN/CGA-B149.1/.2 Natural Gas/Propane Code.(Canada) latest edition or the National
Electrical Code ANSI/NFPA No. 70 or the Canadian Electrical Code CGA 1.6b2005 or latest edition.
In Massachusetts: All gas products must be installed using a “ Massachusetts “ licensed
plumber or gas tter. A “T” handle type manual gas valve must be installed in the gas supply
line to this appliance. This applies to permanently installed natural gas and propane instal-
lations. This does not apply to propane portable installations using a 20 pound tank (not
included) plus regulator and hose assembly, which is supplied with propane gas grills.
Rev. 12-07
Important Safety Considerations
WARNING! Read this manual carefully and completely before using your grill to reduce the risk of re, burn
hazard or other injury, and to ensure proper installation and servicing.
F O R Y O U R S A F E T Y
If you smell gas:
1. Shut o gas to the appliance.
2. Extinguish any open ames.
2. Open lid.
4. If odor continues, keep away from the
appliance and immediately call your gas
supplier or re department.
F O R Y O U R S A F E T Y
1. Do not store or use gasoline or other am-
mable vapors and liquids in the vicinity of
this or any other appliance.
2. An LP cylinder not connected for use shall
not be stored in the vicinity of this or any
other appliance.
A V E R T I S S E M E N T
S’il y a une odeur de gaz:
1. Coupez l’admission de gaz de l’appariel.
2. Éteindre toute amme nue.
3. Ouvrir le couvercle.
4. Si l’odeur continue, évite l’appareil et appelle
tout de suite votre fournisseur de gaz ou les
pompiers.
A V E R T I S S E M E N T
1. Ne pas entreposer ni utiliser de l’essence ni
d’autres vapeurs ou liquides inammables
dans le voisinage de l’appareil, ni de tout
autre appareil.
2. Une bouteille de propane qui n’est pas
raccordée en vue de son utilisation, ne doit
pas être entreposée dans le voisinage de cet
appareil ou de tout autre appareil.
FOR OUTDOOR USE ONLY: If stored
indoors, detach and leave L.P. cylinder
outdoors.
B E F O R E L I G H T I N G
1. Read instructions before lighting.
2. Open lid during lighting.
3. If ignition does not occur in 5 seconds, turn
the burner control(s) o, wait 5 minutes, and
repeat the lighting procedure.
POUR UTILISATION À L’EXTÉRIEUR
SEULEMENT:
Si l’appareil est entreposé
à l’interieur, enlever les bouteilles et les
laisser à l’extérieur.
A V A N T D ’A L L U M E R
L’ A P PA R E I L
1. Lisez les instructions avant d’allumer l’appareil.
2. Ouvrez le couvercle avant d’allumer l’appareil.
3. Si l’appareil ne s’allume pas en 5 secondes,
fermez le robinet du brûleur, attendez 5 minutes, et procédez de nouveau à l’allumage.
Table of Contents
Precautions for Installation and Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Locating Your Grill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Cutout Dimensions for 2008 Built-ins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Unpacking and Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Electrical Requirements & Hook-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Gas Requirements & Hook-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Precautions for Using Your Grill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Leak Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Model Identication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Using the Grill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Lighting the Brass Burners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Using the ProSear Burner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Using the Rotisserie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Using the Smoker Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Cleaning the Grill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Burner Cleaning & Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Light Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Replacing the Briquettes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Side Burner/LPSGE Gas Hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Lighting the Side Burner or LPSGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
How to Obtain Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-27
Gas Plumbing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Parts Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
IF SHIPMENT ARRIVES DAMAGED:
1) VISIBLE LOSS OR DAMAGE: Be certain this is noted on freight bill or express receipt and signed by
person making delivery.
2) FILE CLAIM FOR DAMAGES IMMEDIATELY, regardless of extent of damage.
3) CONCEALED LOSS OR DAMAGE: If damage is unnoticed until merchandise is unpacked, notify
transportation company or carrier immediately and file “concealed damage” claim with them. This
should be done within (15) days of date delivery is made to you. Be sure to retain container for
inspection. We cannot assume responsibility for damage or loss incurred in transit.
See page 25 for information on obtaining service or contacting Lynx.
Precautions for Installation and Storage
1) DO NOT store or use gasoline
or other ammable vapors and
liquids in the vicinity of this or
any other appliance.
2) Never store additional or
empty propane cylinders in the
grill cabinet or around the grill.
Do not store propane cylinders
indoors or on their sides. Never
use dented, rusty or damaged
propane cylinders.
3) Children should not be left
alone or unattended in an area
where a grill is located. Place your
grill well away from areas where
children play. Do not store items
that may interest children in or
around the grill, in the cart or in
the masonry enclosure. When in
use, portions of the grill are hot
enough to cause severe burns.
4) Never move the grill when hot.
5) Always adhere to the required
clearances from combustibles as
detailed. The grill is designed for
outdoor use only. Never use in a
garage, building, shed, breezeway or other enclosed area.
6) Gas grills are not design cer-
tified for and are not to be
installed in or on recreational
vehicles, portable trailers, boats
or any other moving installation.
7) Have an ABC Fire Extinguisher
accessible — never attempt to
extinguish a grease fire with
water or other liquids.
8) Store your grill in a well-ven-
tilated area. Remove the L.P. cylinder, if so equipped, and store
it outdoors in a well-ventilated
area away from heat and away
from where children may tamper with it.
9) Keep any electrical supply
cord and the fuel supply hose
away from any heated surfaces.
Electrical cords should be placed
away from walkways to avoid
tripping hazard.
10) Do not repair or replace
any part of the grill unless specically recommended in this
manual. Other service should be
performed by a qualied tech.
11) If the grill is installed by a
professional installer or technician, be sure that he shows you
where your gas supply shut-o is
located. All gas lines must have
a shut-o that is readily and easily accessible. If you smell gas,
check for gas leaks immediately.
Check only with a soap and
water solution. Never check for
gas leaks with an open ame.
SPECIAL NOTE ON USING YOUR GRILL IN WINDY CONDITIONS
As a high-performance gas appliance, your Lynx grill requires
signicant amounts of air to support the combustion process.
Your grill has been engineered
to take air in through the control panel area, and exhaust the
combustion byproducts out
through the gap between the
front and rear hoods (see gure
3-2 at right).
Using your grill in windy conditions can disrupt the proper ow
of air through your grill, leading to reduced performance, or
in certain severe cases, causing
heat buildup in the control panel
area. This can lead to problems
such as having the control knobs
melt, or burn hazards when the
control panel surfaces become
too hot to touch.
During windy conditions, it is
best if you don’t use your grill.
If you have a freestanding grill,
it is best to position the unit so
the prevailing wind blows into
the front control panel (or at
your back), thus supporting the
proper airflow. Winds hitting
the back of the grill directly are
the most likely to cause prob-
lems, although wind blowing
along the hood gap can also be
problematic.
Please note that damage to
your grill resulting from use
in windy conditions, such
as melted knobs or igniter
wires, or control panel discoloration from heat buildup, are excluded from warranty coverage.
2
SPECIAL NOTE FOR LP USE
Never connect any unregulated
gas supply to the grill. The hose
with regulator and Type 1 connection included with your grill
has these safety features:
• The system will not allow gas to
ow until a positive connection
has been made.
•The system has a thermal element that will shut-o the ow
of gas between 115 and 150ºC
(240 and 300ºF).
• The system has a ow limiting
device which, when activated,
will restrict the ow of gas to 10
cubic feet per hour.
NOTE: The cylinder control valve
must be turned o before any
connection is made or removed.
NEVER USE GRILL WITHOUT
FIRST LEAK TESTING THIS
CONNECTION, FOLLOWING
THE PROCEDURE ON PAGE 11.
Should the large, black, thermally sensitive coupling nut be
exposed to temperatures above
115-150ºC, it will soften, allowing the regulator probe to disengage from the cylinder valve,
thereby shutting o the ow of
gas. Should this occur, do not
attempt to reconnect the nut.
Remove the entire regulator assembly and replace it with a new
one. The cause of the excessive
heat should be determined and
corrected before operating your
grill again. The regulator probe
also contains a ow-sensing element, which will limit the ow
of gas to the regulator to a manageable amount in the event of
a hose or regulator rupture. If it
is evident that the ow control
device has activated, the cause
of the excess ow should be determined and corrected before
using your grill again.
NOTE: Improper lighting procedures can cause the ow control
to activate, resulting in reduced
heat output. If this is suspected,
to reset ow control, shut o
all burner controls and cylinder
valve, wait 30 seconds, then
turn cylinder valve on extremely
slowly, wait ve (5) seconds and
turn burner valve on to light.
Figure 3-1 - The included hose
and regulator must be used if your
grill is set-up for an LP Gas Cylinder.
Figure 3-2
away from prevailing winds and avoid grilling in windy conditions.
- Steady or gusty winds can prevent the normal exhaust of hot gases. Locate your grill
Wind hitting the grill while
in use, especially winds
blowing into or across
this hood gap,
can cause poor
performance and
in some cases
can cause the
control panel
to get danger-
ously hot.
3
Locating Your Grill
4" min. for all other sizes
2" min. for 27" grills
When selecting a suitable location, take into account concerns
such as exposure to wind and
trac paths. Try to keep all gas
supply lines as short as possible.
Never locate the grill under a
roof or overhang, in a building, garage, shed or other such
enclosed area. A carpenter’s
“spirit level” should be used to
assure that the unit is level both
front-to-back and side-to-side.
If it is not level, burner combustion may be erratic or the unit
may not function eciently. If
the oor is uneven or has a decided slope, re-leveling may be
required after each moving of a
freestanding unit.
BUILT-IN INSTALLATIONS:
The LYNX Built-In Grill is designed
for easy installation into masonry enclosures. For non-combustible applications, the grill drops
into the opening shown in the
cutout detail drawing and hangs
from its counter-top trim. A deck
is not required to support it from
the bottom. When using the insulated jacket in a combustible
enclosure, the jacket must be
supported from the bottom by a
ledge on each side or a full deck
beneath the jacket. Review the
detailed drawing and pay special attention to the provisions
shown for gas line hook-up. It is
recommended that the enclosure have ventilation holes to
prevent gas build-up in the event
of a leak. The deck ledges and
counter should be at and level.
If your grill is equipped with a ro-
tisserie, electrical service should
be provided (on the Left Side of
most models).
REAR HOOD CLEARANCE:
Clearance is required behind the
grill to allow the front hood to
open (see gure 4-1). 27” and 36”
models require a minimum of 2”
clearance, while 30”, 42” and 54”
models require a minimum of
4” clearance. The grill exhausts
combustion products and cooking greases to the back. Never locate the grill where this exhaust
will be dicult to clean.
Figure 4-1
to allow opening of front hood.
CLEARANCE TO COMBUSTIBLE
CONSTRUCTION:
Minimum clearance from sides
and back of unit to adjacent
combustible construction below
top of unit are 12” from sides and
12” from back.
Dégagement minimal entre les
parois latérales et l’arrière de
l’appariel et la construction combustible au-dessous du panneau
supérieur de l’appareil (30 cm à
partir des parois latérales et 30 cm
- Required clearance
à partir de l’arrière).
Minimum horizontal clearance
from sides and back of unit to
adjacent vertical combustible
construction extending above
top of unit is 12” from sides and
12” from back.
Dégagement horizontal minimal
entre les parois latérales et l’arrière
de l’appariel et la construction
verticale combustible au-dessus
de l’appareil (30 cm à partir des
parois latérales et 30 cm à partir
de l’arrière).
Do not use this appliance under
overhead combustible surfaces.
Ne pas utiliser cet appareil sous
une surface combustible.
A minimum of 6” of clearance is
needed on each side of the grill
for the motor and skewer.
If the grill is to be placed into
a combustible enclosure, an
approved insulated jacket is
necessary and is available from
your LYNX dealer. Use only a
LYNX insulated jacket as it
has been designed and tested
specically for your Grill. Refer
to next page for cutout dimensions.
WA R N I N G
Installing this product
into a combustible enclosure without an insulated jacket could result
in re, property damage
and personal injury.
4
Cutout Dimensions for 2008 Built-ins
Insulated
Jacket
a
f
e
c
d
b
2" 0 or 2" square holes
for manifold connection
(rear or bottom access)
12" min.
Grill
CocktailPro*
Warming Drawer/
Convenience Center
Utility
Drawer
Side
Burner
Access
Doors
19"
A
B
D
E
G
F
H
29"
2 1/4"
4 1/2"
min.
3 1/2"
1 1/8"
min.
1 1/8" min. for model LUDE
3 1/2" min. for model LUDXL
2 1/2" min. for model LDR
3 1/4" min.
2"
10 7/8"
36 3/8"
min.
C
10 1/8" for L36 models
Dim C to cabinet face
5/8" for Grills
9/16" for Complementary Products
Depth equals
countertop
overhang
*CocktailPro should have an
open bottom for plumbing
and drain access.
Counter top Notch Detail
Specifications are subject to change without notice.
Professional Grills and ProSear Pod
Model A B C D E F G H
L27 - 26 22 - - - - L30 - 29 24 1/2 - - - - L36 - 35 22 - - - - L42 - 41 24 1/2 - - - - L54 - 53 24 1/2 - - - - -
Note: Insulated jacket required for all grills installed
into a combustible enclosure. See detail below.
With Insulated Jacket Installed
Model a b c d e f
LIJ27 33 5 24 4 1/2 3 11 5/8
LIJ30 36 5 26 1/2 4 1/2 3 11 5/8
LIJ36 42 5 24 4 1/2 3 11 5/8
LIJ42 48 5 26 1/2 4 1/2 3 11 5/8
LIJ54 60 5 26 1/2 4 1/2 3 11 5/8
Complementary Products
Model A B C D E F G H
LDR21-1 - - - 19 1/4 - - - LDR27-1 - - - 25 1/4 - - - LDR30-1 - - - 28 1/4 - - - LDR36-2 - - - 34 1/4 - - - LDR42-1 - - - 40 1/4 - - - -
LSB1 12 1/8 - 24 1/2 - - - - LSB2 12 1/8 - 24 1/2 - - - - LSB2PC 24 1/4 - 24 1/2 - - - - LPSGE 12 1/8 - 24 1/2 - - - - -
LUDE - - 24 - 12 1/8 19 1/4 - LUDXL - - 24 1/4 - 17
L30WD - - 20 1/2 - - - 28 1/2 10
L42CC - - 24 1/2 - - - 40 1/4 19 3/8
CS30 - - 22 3/4 - - - - -
Side Burners and ProSear Grill Extender
Access Doors
Utility Drawers
1/4 18 9/16 - -
Warming Drawers
CocktailPro
5
Unpacking and Assembly
Your grill arrives nearly ready to
use and requires little assembly. By carefully following these
steps, you will be assured of safe
initial operation.
1) Cut the main strap holding
the grill to the pallet. With assistance, remove grill from pallet
and place into desired location.
2) Carefully cut the cable ties
securing the warming rack and
rotisserie spit (if equipped). Remove these parts and set aside.
3) Remove the grill racks, then
remove any loose items from the
rebox, including the rotisserie
motor and L.P. hose.
4) Carefully remove the bri-
quette trays by lifting the front
of the tray and sliding it towards
the front of the grill.
5) Inspect briquette trays for
loose or missing briquettes. If
found, follow procedure at right
to reinstall.
6) Cut and remove wire and/or
cable ties from burners. ProSear
burners may be secured from the
bottom side. Remove styrofoam
block from under ProSear burner
cover. Ensure that all burners are
properly in line with and seated
on the burner valve orice.
7) On ProSear models, cut and
remove ties from the burner
partition on the left side of the
ProSear burner.
8) Re-install briquette trays by
reversing procedure from step 4.
9) Re-install grill racks.
You are now ready to proceed
with the utility connections.
TO REPLACE BRIQUETTES
The special Lynx ceramic briquettes are secured to the trays
with stainless steel clips. To insert a briquette into the tray, it
is necessary to remove the clip
from one side of the empty slot.
This is done by bending the retaining tabs for the clip located
on the back side of the briquette
tray as shown below.
Carefully cut and
remove main strap.
Discard blocks and
foam padding.
Rotis motor, electrical transformer,
etc. in boxes in
firebox.
Figure 6-1
- Identication of items needing to be removed and/or assembled prior to use.
Cut and
remove cable
ties holding
rotis spit.
Remove all
wire ties and
padding from
burners.
6
Electrical Requirements & Hook-up
WARNING
Electrical Grounding
Instructions:
This outdoor gas cooking appliance is equipped with a threeprong (grounding) plug for your
protection against shock hazard
and should be plugged directly
into a properly grounded threeprong outlet. Do not cut or remove
the third prong from this plug.
AVERTISSEMENT
Instruction pour la mise à la
terre electrique:
Cet appareil est muni d’une che à
trois broches (mise à la terre) an
de vous protéger des chocs et doit
être branché directement dans une
prise de courant à trois broches adéquatement mise à la terre. Il ne faut
pas couper ou enlever la broche de
mise à la terre de cette che.
CONNECTION TO AC
Installation should include an
outdoor 120VAC 15A GFI electrical outlet located adjacent to the
grill. A qualied electrician can
install a GFI outlet either inside
the island enclosure for built-in
units, or near the normal location
of use for freestanding units. The
GFI plug has an internal breaker
which reduces shock hazard.
For freestanding grills, simply
plug the electrical cord into a GFI
plug. For built-in units, the supplied 12V transformer is connected to the grill during installation
(see Fig. 7-1).
Figure 7-1
nection point on left rear grill
frame.
Once connected to the grill, the
power cord may be plugged into
a GFI outlet. If the electrical system fails to operate, a connection
may have come loose in shipping.
See the Troubleshooting section
for more details.
- Transformer con-
BATTERY REPLACEMENT
(Recommended Batteries include:
Rayovac Maximum Plus Alkaline #813, D size / Duracell Coppertop Alkaline - #MN1300, D size / Energizer
Alkaline - #E95, D size)
Your grill includes two D Cell
batteries that provides backup
power for the electronic ignition
system. To replace the batteries,
follow this procedure:
1) Locate the battery compart-
ment. On free standing models
this is located inside the grill cart
on back left. (For 42” free standing models you will need to remove both storage drawers). For
built-in models it is located under
the unit where the installer has
mounted the battery and transformer bracket. (See gure 7-2)
2) Disengage the cover from the
battery compartment by pushing
the clips on the top and bottom
of the compartment together
and remove the cover.
3) Insert 2 new D cell batteries
into the battery compartment
and replace the cover.
Figure 7-2
compartment.
- Locating battery
Amperage
12 Volt transformer is .6 amps
Rotisserie motor is .5 amps
7
Loading...