Page 1
Page 2
INSTALLATION OF MODULAR DRAWER
3)
PLACE THE DRAWER FRAME INSIDE THE PRE-CUT HOLE IN
THE FRONT OF THE ISLAND (PER CUT-OUT DIMENSIONS ON PAGE 1).
CAREFULLY SLIDE THE FRAME ALL THE WAY IN UNTIL THE FRONT
FLANGE IS FLUSH WITH THE ISLAND FRONT SURFACE. YOU WILL NOTE THAT
THERE ARE 2 SETS OF MOUNTING SLOTS LOCATED ON THE INSIDE OF THE SIDES
OF THE FRAME. SELECT THE SLOT WHICH IS THE MOST CENTERED OVER THE
FRONT MATERIAL THICKNESS OF THE ISLAND. USE THE #8 X 1-1/2" SCREWS
AND FINISHING WASHERS PROVIDED TO SECURE FRAME. IF FRONT SURFACE
IS HARD, IT MAY BE NECESSARY TO DRILL PILOT HOLES WITH A 1/8 TO 5/32 DRILL.
4)
IT IS RECOMMENDED THAT THE REAR OF THE DRAWER FRAME BE
SUPPORTED IN ORDER TO UTILIZE THE FULL CAPACITY OF THIS HEAVY
DUTY DRAWER SYSTEM. THERE ARE 2 METHODS TO ACCOMPLISH THIS.
METHOD #1-
23-3/8" BACK FROM THE INSIDE EDGE OF THE ISLAND FRONT. A COMMON
2 X 4 CAN BE USED FOR THIS PURPOSE. USE THE SHORTER #10 X 1/2"
SCREWS PROVIDED AND SECURE THE BACK OF THE DRAWER FRAME TO
THE SUPPORT MEMBER BY DRIVING THE SCREW THROUGH THE BACK
FRAME AND INTO THE MEMBER.
METHOD #2
SECURE A VERTICAL SUPPORT MEMBER, INSIDE THE ISLAND,
- SEE PAGE 3
PRE-CUT HOLE
#10 X 1/2 SCREW
DRAWER FRAME
FINISHING WASHER
#8 X 1-1/2" SCREW
DRAWER
5)
REINSTALL DRAWER INTO DRAWER FRAME
ASSURING FIRST THAT THE BALL BEARING TRACK IS
POSITIONED TOWARD THE REAR OF EACH SLIDE.
ALLIGN SLIDES AND PUSH DRAWER FIRMLY INTO FRAME
AND ALL THE WAY TO THE CLOSED POSITION BEFORE
ATTEMPTING TO RE-OPEN. RESISTANCE WILL OCCUR
DURING THE INSERTION PROCESS- DO NOT ATTEMPT TO
OPEN DRAWER BEFORE IT HAS BEEN INITIALLY FULLY INSERTED,
AS, THIS CAN DAMAGE THE SLIDES.
P/N 33050 Page 2
START:
1)
REMOVE DRAWER FROM OUTER SLIDE FRAME BY
SLIDING DRAWER OUT AWAY FROM FRAME UNTIL DRAWER STOPS.
DISENGAGE THE DRAWER SLIDE BY ACTIVATING THE RELEASE
LEVERS. PRESS DOWN ON THE RIGHT LEVER AND UP ON THE LEFT
LEVER. CAREFULLY PULL DRAWER COMPLETELY AWAY FROM
SLIDE.
2)
BEFORE PROCEEDING, PUSH THE REMAINING PORTION OF THE
SLIDE (MOUNTED IN THE FRAME) ALL THE WAY IN AND SLIDE THE
BALL BEARING TRACK OF THE SLIDE ALL THE WAY BACK UNTIL IT
STOPS.
Page 3
LYNX MODULAR DRAWER MOUNTING KIT
TOP INSTALLATION BRACKET
1
FASTENER USED
2 3 4
2 3 4
2 3 4
TOP SLIDED BRACKET
CONNECTOR STRAP
FASTENERS SUPPLIED:
1 #10 X 1/2" TYPE 'A' SCREW (QTY 2 SUPPLIED)
2 #8-32 X 3/8" MACHINE SCREW (QTY 8 SUPPLIED)
3 #8-32 LOCK NUT (QTY 8 SUPPLIED)
4 #12 X 1/2" O.D. FLAT WASHER (8 SUPPLIED)
5 1/4-20 X 1/2" MACHINE SCREW (QTY 2 SUPPLIED)
6 1/4-20 LOCK NUT (QTY 2 SUPPLIED)
READ ALL INSTRUCTIONS FIRST
BEFORE BEGINNING
CONNECTOR STRAP
BOTTOM BRACKET
(QTY 2)
5 6 7
7 1/4" X 11/16 O.D. FLAT WASHER (QTY 2 SUPPLIED)
STEP 1- ALLIGN TOP INSTALLATION BRACKET WITH REAR EDGE OF UPPER DRAWER FRAME. IF THIS BRACKET DOES NOT REACH
THE DRAWER FRAME, ADD THE TOP SLIDER BRACKET AND ASSEMBLE WITH 2 SETS OF #8 SCREWS, NUTS, AND WASHERS
(ITEMS #2, #3 & #4). ADJUST THESE 2 BRACKETS SO THAT, WHEN POSITIONED BEHIND DRAWER AND HOLES ARE ALLIGNED,
THE DRAWER HANGS LEVEL. SECURE THE TOP INSTALLATION BRACKET TO THE UNDER SIDE OF THE ISLAND TOP BY FIRST
PRE-DRILLING (2) 5/32 HOLES (1/2" DEEP MAX) AND INSTALLING (2) #10 X 1/2" TYPE 'A' SCREWS (ITEM #1). FASTEN THE LOWER
END OF THE BRACKET ASSEMBLY TO THE UPPER HOLE AT THE REAR OF THE DRAWER FRAME. USE THE #8 SCREW, NUT AND
WASHER (ITEMS #2, #3 & #4). IF YOU ARE ONLY INSTALLING (1) DRAWER, YOU ARE NOW FINISHED. IF MORE THAN (1) DRAWER
IS BEING INSTALLED, GO TO STEP 2.
STEP 2- ATTACH THE SECOND DRAWER TO THE FIRST (TOP) DRAWER BY USING THE CONNECTOR STRAP. ALLIGN THE TOP SLOT OF
THE STRAP TO THE BOTTOM HOLE AT THE REAR OF THE UPPER DRAWER FRAME. SECURE WITH #8 SCREW, NUT, AND WASHER
(ITEMS #2, #3, ). ALLIGN THE BOTTOM SLOT OF THE STRAP WITH THE TOP HOLE AT THE REAR OF THE SECOND DRAWER FRAME.
REPEAT THIS PROCESS, USING THE SECOND CONNECTOR STRAP, FOR THE THIRD (BOTTOM) DRAWER.
STEP 3- ASSEMBLE THE 2 HALVES OF THE BOTTOM BRACKET INTO A 'U' SHAPE BY USING THE (2) 1/4-20 X 1/2" MACHINE SCREWS, NUTS,
AND WASHERS (ITEMS #5, #6, & #7). HAND TIGHTEN ONLY., PLACE THIS BRACKET ASSEMBLY UNDER THE THIRD (BOTTOM) DRAWER
FRAME. ADJUST BRACKET ASSEMBLY UNTIL IT FIRMLY CONTACTS THE BOTTOM OF THE DRAWER FRAME. TIGHTEN SCREWS AND NUTS
SECURELY. NO ADDITIONAL FASTENERS ARE REQUIRED. PLEASE NOTE- THIS BOTTOM BRACKET IS USED FOR ADDITIONAL SUPPORT IN A
3-DRAWER INSTALLATION. IT CAN ALSO BE USED INSTEAD OF THE TOP BRACKET ASSEMBLY IN A 3-DRAWER INSTALLATION WHERE
IT IS NOT DESIRED TO DRILL INTO THE TOP ISLAND SURFACE.
2 3 4
2 3 4
2 3 4
2 3 4
5 6 7
P/N 33050 Page 3
Loading...