Page 1
MaKe tHe Most oF Your
siDe Burner accessorY
care & use/installation
Page 2
WarninGs
WARNING
READ THIS MANUAL CAREFULLY and completely before using your grill to reduce the risk of:
1. Fire
2. Burn hazard, personal injury or property damage
3. Ruined steaks or other unpleasant cooking experiences
4. Unapproved installation or servicing.
THIS PRODUCT IS DESIGNED FOR OUTDOOR USE ONLY. Improper installation, adjustment, alteration, service
or maintenance can cause property damage, injury or death.
Read this manual thoroughly before installation, use, or servicing of this product.
DANGER
IF YOU SMELL GAS:
1. Shut off all gas supply lines to the grill accessory.
2. Extinguish any open flames.
3. Carefully open the lid. Remember, it may be
extremely hot!
4. If odor continues, keep everyone away from the
grill accessory and immediately call your gas
supplier or your fire department.
WARNING
1. DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
2. An LP cylinder not connected for use shall
not be stored in the vicinity of this or any
other appliance.
DANGER
S’IL Y A UNE ODEUR DE GAZ:
1. Coupez l’admission de gaz de l’appariel.
2. Éteindre toute flamme nue.
3. Ouvrir le couvercle.
4. Si l’odeur persiste, éloignez-vous de
l’appareil et appelez immédiatement le
fournisseur de gaz ou le service d’incendie.
AVERTISSMENT
1. Ne pas entreposer ni utiliser de l’essence ni
d’autres vapeurs ou liquides inflammables dans le
voisinage de l’appareil, ni de tout autre appareil.
2. Une bouteille de propane qui n’est pas raccordée
en vue de son utilisation, ne doit pas être entreposée dans le voisinage de cet appareil ou de
tout autre appareil.
Warning! CALIFORNIA PROPOSITION 65
1. The burning of gas cooking fuel generates some by-products which are on the list of substances which are
known by the State of California to cause cancer or reproductive harm.
2. California law requires businesses to warn customers of potential exposure to such substances. To minimize
exposure to the substances, always operate this unit according to the use and care instructions found in this
manual. Be certain to provide adequate ventilation when cooking.
3. California Proposition 65 lists “Silica, crystalline” which is used in one of the components of the IR burner, as
an agent known to the state of California to cause cancer.
2
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
|
Page 3
HoW to liGHt Your Grill accessorY
1. Before each use, complete the checklist below.
2. Make sure all burner control knobs are in the “OFF” position.
3. Push and hold the control knob for 2-5 seconds, allowing the igniter to heat up.
4. Turn the knob to the “LITE” position.
5. After ignition set the knob to the desired setting.
cHecKlist BeFore eacH use (For Your saFetY)
•Do you smell gas? If yes, shut off everything and call the
gas company or a qualified plumber to check for leaks, if
not please continue.
•Are you prepared to stay with the side burner during the
entire cooking process? If not, gather what you need before starting the lighting process. If yes, please continue.
•Is your cooking area free and clear of any combustibles,
besides your food, that might ignite? If no, clear the area
before starting the lighting process, If yes, please continue.
•Do all control knobs turn freely? If not, call for service; if
yes, please continue.
•If you are using a portable propane cylinder, is it connected and leak tested? If not, check the connection before
continuing. If yes please continue.
•Do you know where your side burner’s main gas supply
shut-off valve is located? If not, locate it before continuing. If yes, please continue.
•Are all burners properly seated in the side burner? If not,
seat the burners properly before continuing. If yes please
continue.
•Is the wind blowing just lightly and not blowing on the
side burner? If not, wait until the wind subsides or turn
your free-standing grill so the wind goes into the front of
the grill. If yes, please continue with the lighting process.
PART NO. 33487 REV.B 3/13
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
3
|
Page 4
WarninGs
WARNING
•Never use dented, rusty or damaged propane cylinders. Never store additional or empty propane cylinders
in the cabinet or in the vicinity of this or any other appliance. Do not store propane cylinders indoors or on
their sides.
•Children should never be left alone or unattended in an area where an accessory is located. Place your
accessory well away from areas where children play. Do not store items that may interest children in or
around the area of your accessory, in your accessory cart, or in the masonry enclosure.
•Never move the accessory when hot. When in use, portions of the accessory are hot enough to cause
severe burns.
•Always maintain the required clearances from combustibles as detailed. Accessories are designed for outdoor use only. Never use in a garage, building, shed, breezeway, or other enclosed area. Do not use this
equipment under any overhead combustible construction.
•Grill accessories are not designed or certified for and are not to be installed in or on recreational vehicles,
portable trailers, boats or any other moving installation.
•Always have an ABC Fire Extinguisher accessible — never attempt to extinguish a grease fire with water or
other liquids.
•Storing your accessory: Store your accessory in a well-ventilated area. If stored indoors, detach and leave
LP cylinder outdoors in a well-ventilated area away from heat and away from where children may tamper
with it.
•Keep any electrical supply cord and the fuel supply hose away from any heated surfaces. Electrical cords
should be placed away from walkways to avoid tripping hazard.
•Do not repair or replace any part of the accessory unless specifically recommended in this manual. Other
service should be performed by a qualified technician.
•If the accessory is installed by a professional installer or technician, be sure that he/she shows you where
your gas supply shut-off is located. All gas lines must have a shut-off that is readily and easily accessible.
If you smell gas, check for gas leaks immediately. Check only with a soap and water solution. (See INDEX:
“Leak Testing” for further details.) Never check for gas leaks with an open flame.
•Inspect the LP gas supply hose prior to each use of the accessory. If there is evidence of excessive abrasion
or wear, or the hose is cut, it must be replaced before using the accessory.
•Never remove the grounding prong from the plug or use this product with an ungrounded, 2-prong
adapter.
THIS MANUAL MUST REMAIN WITH THE PRODUCT OWNER FOR FUTURE REFERENCE.
This product complies with ANSI standard Z21.58/CSA
1.6 latest edition and has been tested and approved by
Intertek.
4
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
|
To obtain replacement parts or service contact:
Lynx Professional Grills
5895 Rickenbacker
Commerce, CA 90040
888-289-5969
Page 5
a MessaGe to our custoMers
You’ve just joined the world of Lynx cooks … a discriminating collection of
amateur and professional chefs that take outdoor cooking to a new level.
Lynx manufactures many accessory cooking appliances to compliment your
Lynx grill and your desire for truly superior cooking results.
Your appliance has been designed and built with meticulous attention to
detail and it offers some unique and powerful features. You can achieve
maximum performance and enjoyment of these features only by carefully
reading this manual ... before your first cook-out.
This manual includes important safety tips and great hints for better grilling. You should keep it handy for easy reference.
Also, at Lynx, we enjoy hearing from our customers. We like to hear about
your successes but also about any difficulties you are having. Please feel
free to contact us with any questions or problems, or just to share a new
recipe. Please include the model number of your appliance in your correspondence.
With the proper use and care this product will provide years of trouble-free
service.
Should your Lynx appliance change ownership, please make sure that the
new owner receives this manual.
Thanks again for your purchase. Enjoy!
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
5
|
Page 6
WarninGs
WARNING
1. The outdoor cooking gas appliance and its individual shutoff valve must be disconnected from the gas supply
piping system during any pressure testing of that system at test pressures in excess of 0.5 psi (3.5 kPa).
2. The outdoor cooking gas appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal
to or less than 1/2 psi (3.5 kPa).
STATE OF MASSACHUSETTS
1. Massachusetts requires all gas be installed using a plumber or gas fitter carrying the appropriate Massachusetts license.
2. All permanently-installed natural gas or propane installations require a “T” handle type manual gas valve be
installed in the gas supply line to this appliance.
3. This does not apply to portable propane installations using a 20 pound cylinder.
WARNING - ELECTRICAL GROUNDING
•Product installation must meet local electric codes or, in the absence of local codes, the latest edition of the
National Electrical Code ANSI/NFPA No. 70 or the Canadian Electrical Code CGA 1.6b2005.
•Use only a Ground Fault Interrupter (GFI) protected circuit with this outdoor cooking gas appliance.
•This accessory is equipped with a three prong (grounding) electric plug for your protection against shock hazard
and must be plugged directly into a properly grounded three prong outlet. Never cut or remove the grounding
prong from this plug.
•Use only extension cords with a 3 prong grounding plug, rated for the power of the equipment, and approved
for outdoor use with a “W-A” marking.
•To protect against electric shock, do not immerse any part of the power cord, an extension cord or any plugs in
water or other liquid.
•Unplug the product from the outlet when not in use and before cleaning. Allow it to cool before putting on or
taking off parts.
•Do not let the cord hang over the edge of a table or touch hot surfaces.
•Do not operate any outdoor cooking gas appliance with a damaged cord, plug, or after the appliance malfunc-
tions or has been damaged in any manner. Contact the manufacturer for repair.
6
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
|
Page 7
iMportant saFetY precautions
Please review these imPortant safety Precautions before you use your
grill accessory.
1. NEVER LEAVE THE GRILL ACCESSORY UNATTENDED
WHILE COOKING.
2. Ensure all tie-down wires have been removed from the
burners.
3. Always use caution when operating the grill accessory
in a windy area. (See INDEX: “Grilling in Windy Conditions” for further details.)
4. Avoid wearing loose-fitting garments or long sleeves
while grilling. They could ignite.
5. Never touch the grill accessory racks or immediate
surrounding metal surfaces with your bare hands while
grilling.
6. Use an insulated glove or mitt when opening and operating the grill accessory.
7. The grill accessory covers must be fully removed or
opened while lighting the grill accessory. Releasing
fuel into a closed grill accessory before lighting will not
make it light sooner or more efficiently. It will only risk
explosion and personal injury or death. Never lean over
hot grill accessory surface or look directly into the grill
accessory when attempting to light.
8. Do not heat unopened food containers as pressure
build-up will cause the container to explode.
9. Do not use aluminum foil to line grill accessory racks
or drip pans. This will alter the airflow or trap excessive heat in the control area and can melt knobs and
ignition modules. Such damage is specifically excluded
from your warranty.
10. Never use charcoal or any other solid fuel in the grill
accessory.
11. Cooking excessively fatty meats and oils will cause flare
ups. Internal fires or damage caused by them or by
the grill accessory being left unattended while cooking
are not covered under the terms and conditions of our
warranty.
12. Never grill without a drip pan in place if your accessory
utilizes a built-in drip pan. Always ensure the drip pan
is pushed all the way to the back of the grill accessory.
When not correctly in place, hot grease can leak downward and produce a fire or explosion.
13. Grease is extremely flammable. Let hot grease cool
down before attempting to handle or dispose of it.
The drip tray should be cleaned of grease on a regular
basis.
14. Do not use the grill accessory unless a leak check has
been performed on all gas connections. (See INDEX:
“Leak Testing” for further details.)
15. Never operate the grill accessory while under the influence of alcohol or drugs.
16. Do not lean on side shelves and never place a load
weighing more than 25 pounds on a side shelf.
17. If any burner does not light or goes out during operation, turn off all gas control knobs and wait five (5)
minutes before attempting to re-light.
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
7
|
Page 8
taBle oF contents
A MESSAGE TO OUR CUSTOMERS 5
IMPORTANT SAFETY PRECAUTIONS 7
USING YOUR LYNX ACCESSORY 9
Accessories Covered in this Manual 9
USING THE LYNX POWER BURNER (LPB) 10
Smell of Gas While Cooking 10
Yellow Flames 10
LIGHTING INSTRUCTIONS FOR ALL ACCESSORIES 11
Safety Practices and Precautions 11
At Each New Season 11
Purging the Gas Lines 11
Match Lighting 11
Low Heat Flame Adjustment 12
CONTACTING LYNX CUSTOMER CARE 13
BEFORE YOU START 14
If Shipment Arrives Damaged 14
Visible Loss or Damage 14
Concealed Loss or Damage 14
Important Notes 14
Where’s the Wind? 14
How Long is Your Run? 14
Are You “On-the-Level”? 14
Built-in Installations 15
Clearance to Combustible Materials 15
GAS & ELECTRIC CONNECTIONS 16
Gas Plumbing 16
Natural Gas 16
LP Gas 17
LP Connections 17
Propane Hook Up 18
Natural Gas Hook Up 18
Maximum Runs for all appliances on supply line 18
Electrical Connections 19
Optional Electrical Kits 19
Connecting the Wiring 19
Testing the Installation 20
Leak Testing 20
Fixing a Gas Leak 20
SCHEMATICS 21
SPECIFICATIONS & INSTALLATION 22
LYNX LIMITED WARRANTY 24
LYNX COMMON AREA LIMITED WARRANTY 25
SIDE BURNER EXPLODED PARTS VIEW 26
INDEX 27
8
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
|
Page 9
Accessories covered in this MAnuAl
usinG Your lYnX accessorY
This manual covers several Lynx accessory appliances and optional accessories for those appliances.
Except where noted, the assembly, installation and use of these Lynx accessories is identical.
POWER BURNER
MODEL LBP
The Lynx Power Burneris a dual-ring commercial style
burner with a range of 3,000 to 47,000 BTU’s.
PREP CENTER
MODEL LSBPC-1
The LSBPC-1 Prep Center Features two 15,000 BTU burners
and an integral bamboo cutting board for food prep.
SIDE BURNER 1 & 2
MODELS LCB1-2 & LCB2-2, LSB1-2 & LSB2-2
The LCB1-2 & LCB2-2, LSB1-2 & LSB2-2 (Lynx Side Burner
1 & 2) features either one or two 15,000 BTU burners for
cooking smaller food items. The LCB1-2 & LCB2-2 can be
mounted directly to most Lynx grills. For the 27” and 36”
Lynx grills with smaller depths, a LCB-BKT adapter is available. The LSB1-2 and LSB2-2 are designed for installation
in a non-combustible, built-in enclosure.
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
9
|
Page 10
The Lynx Power Burner incorporates a cast brass, dual-
USING THE LYNX POWER BURNER (LPB)
IF YOU SMELL GAS WHILE THE GRILL ACCES-
SORY IS OPERATING, IMMEDIATELY TURN OFF ALL
BURNERS AND SHUT OFF THE MAIN FUEL SUPPLY.
ring, burner.
Each ring can be independently operated for maximum heat
control. Used together they can generate up to 47,000 BTU’s.
SMELL OF GAS WHILE COOKING
WARNING!
•Perform a leak test (See INDEX: “Leak Testing” for further
details.)
•Check for blockages.
YELLOW FLAMES
A yellow flame on the main burners indicates a lack of air.
But, if the air around the grill is dusty or if heavy grease is
present, some orange tips on the burner flame are normal.
•ADJUST THE AIR SHUTTER
The knob on the left controls the outer burner ring and the
knob on the right controls the inner burner ring.
The Hot Surface ignition system provides reliable ignition.
The main grate can easily handle oversized stock pots and
removing the center grate accommodates a commercial
style round-bottom wok base (12 inch minimum).
The Lynx Power
Burner also features a
fully extendable stainless steel drip pan.
ONLY DO THIS WHEN THE ACCESSORY HAS COOLED
DOWN COMPLETELY! Make sure all grill controls are in the
“OFF” position.
1. Remove the cooking grates.
2. Reach under the drip guard and rotate the air shutters
to adjust.
10
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
|
3. Ensure that the burner is seated correctly on the frame,
with the brass peg seated inside the positioning hole.
4. Re-light and check the flame.
Page 11
SAFETY PRACTICES AND PRECAUTIONS
Lighting instructions for ALL Accessories
WARNING
Read the ‘User Manual/Installation Instructions
carefully and completely before using your grill
or grill accessory to reduce the risk of fire, burn
hazard or other injury.
Ensure that burner ties and all packing materials are removed before lighting any new accessory.
AT EACH NEW SEASON
At the start of each new grilling season you should remove
the cooking grates and check the burners, venturis, orifices
and valves for obstructions.
PURGING THE GAS LINES
You should purge the gas line of air before attempting to
light the grill accessory.
1. Make sure all grill controls are in the “OFF” position.
2. Slowly turn on the main gas supply.
3. Push in the control knob for the burner furthest from
the fuel source. Using the burner furthest from the fuel
source will completely purge the lines. It will take several seconds for the burner to light.
4. Hold the knob ON for about 20 seconds to allow the
air in the system to purge and the burner to light
5. Wait at least 5 minutes after shutting off the control
before attempting to light the burners.
MATCH LIGHTING
If a burner fails to light after several attempts, it can be
match lit. If you’ve just attempted to light the burner with
the igniter, allow 5 minutes for any accumulated gas to dissipate before match lighting.
Make sure all knobs are in the OFF position. Keep your face
as far away from the burner as possible.
Spiders and insects often nest in these areas of the accessory and can disrupt air flow, causing damage to the accessory and personal injury.
Also, check all hoses and fittings for damage, abrasion,
wear and tear and repair, if necessary, before turning the
gas on.
Replacement pressure regulators and hose assemblies,
must be the type specified by Lynx. The pressure regulator
and hose assembly supplied with the unit must be used.
If the unit is LP, screw the regulator into the tank and leak
check the hose and regulator connections with a soap and
water solution before operating the burner. Turn all knobs
to OFF then SLOWLY turn on the gas supply valve.
Do not use any grill accessory if you smell gas.
Using the manual lighting rod, pass a lit match over the
ports of the burner. The LYNX Power Burner features a
lighting rod as shown above.
Push and turn the control knob of the burner to ‘Lite”. If the
burner does not light in 4 seconds, turn the knob off and
wait 5 minutes before attempting again.
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
11
|
Page 12
LOW HEAT FLAME ADJUSTMENT
Lighting instructions for ALL Accessories ...continued
The burners on your Lynx accessory feature an adjustable
low setting.
Fluctuations in gas pressure, gas conversion and even in the
quality of the gas itself may affect burner performance at
the “LOW” setting. It could be either too high or too low.
To adjust the burner for low setting:
1. Make sure the grill accessory is cool.
2. Remove the grates so that you can see the flame while
adjusting the burner.
3. Light the burner and set it to “LOW”. (all the way counter- clockwise).
4. Pull off the control knob.
5. While holding the valve shaft with pliers, insert a thin
flat-blade screwdriver into the shaft and, while watching
the flame, adjust it to a minimum stable setting.
Use a small screwdriver for low
setting burner adjustment.
12
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
|
Page 13
contactinG lYnX custoMer care
Before calling Lynx Customer Care, please make sure you
have the following information:
•Model number
•Date of purchase
•Proof of purchase by the original owner
•Serial number
The serial number can be located on the rating plate sticker. You may have a sticker on the back page of this manual.
If not, you will find one located either on the underside of
the drip tray (if you have one), on the heat shield behind
the front panel, or on the inside left panel wall.
For warranty service, contact the Lynx Customer Care
Department for an authorized service agent near you at:
Your satisfaction is of the utmost importance to us. If a
problem cannot be resolved to your satisfaction, please
write, fax or email us:
Lynx Professional Grills
5895 Rickenbacker
Commerce, CA 90040
Lynx Customer Care: (888) 289-5969
Tel: (323) 838-1770
Fax: (323) 838-1778
www.lynxgrills.com
Contact Lynx for replacement parts. Parts are shipped
F.O.B. Commerce, CA.
(888) 289-5969
www.lynxgrills.com
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
13
|
Page 14
BeFore You start
Important notes
Where’s the Wind?
When selecting a suitable location, consider important fac-
tors such as exposure to the wind and foot-traffic patterns.
If you have a freestanding grill, position it so the prevailing
wind blows into the front control panel (at your back when
grilling), supporting the proper front-to-rear airflow.
Built-in accessories located in areas with prevailing winds
should be protected by a wind barrier.
hoW Long is Your run?
Keep all gas supply lines as short as possible because gas
lines lose pressure over distance and with each elbow and
tee that is added. This drop in pressure affects accessory
performance. (See INDEX: “Gas Supply Line Runs” for
further details.)
Are You “on-the-LeveL”?
Proper leveling during installation is critical. An accessory
that is out of level will cause erratic burner combustion and
inefficient, uneven heating. A carpenter’s spirit level should
be used to level the accessory both front-to-back and side-
to-side.
If the floor is uneven or has a decided slope, re-leveling
may be required each time you move a freestanding unit.
WARNING
•Never install this product into a combustible enclosure. Doing so could result in fire, property damage and personal injury.
•Never locate the accessory under a roof or overhang, in a building, garage, shed or other such enclosed area.
•Always maintain the required clearances from combustibles as detailed. Accessories are designed for outdoor
use only. Never use in a garage, building, shed, breezeway, or other enclosed area. Do not use this equipment
under any overhead combustible construction.
•Installation must conform with local codes or, in the absence of local codes, with either the National Fuel Gas
Code, ANSI Z223.1/NFPA 54, or Natural Gas and propane Installation Code, CSA B149.1, or Propane Storage
and Handling Code, B149.2, in Canada.
iF sHipMent arriVes DaMaGeD
VISIBLE LOSS OR DAMAGE
Be certain any visible damage to the carton is noted on
freight bill or express receipt and signed by the person
making delivery.
FILE CLAIM FOR DAMAGES IMMEDIATELY, regardless of
extent of damage.
CONCEALED LOSS OR DAMAGE
If damage is unnoticed until the accessory is unpacked, notify the transportation company or carrier immediately and
file a “concealed damage” claim with them. This should
be done within (15) days of the date delivery is made to
you. Be sure to hold on to the container for inspection. We
cannot assume responsibility for damage or loss incurred
in transit. (See INDEX: “Obtaining Service from Lynx” for
further details.)
14
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
|
Page 15
BUILT-IN INSTALLATIONS
Before you start...continued
CLEARANCE TO COMBUSTIBLE MATERIALS
Lynx built-in accessories are intended for installation in a
built-in enclosure constructed of non-combustible materials.
The accessory drops into the opening shown in the cutout
detail drawing and hangs from its counter-top trim. A deck
is not required to support it from the bottom.
Pay special attention to the provisions shown for gas line
hook-up. (See INDEX: “Cut-out Dimensions for Built-in Grills
& Accessories”)
Installation provisions may be made for the Power Burner
installation. The Power Burner cooking height may be
reduced to better accommodate large cooking pots. Clearances to combustible material must be maintained as outlined below. No combustible material shall be used in the
construction of a counter top using a recessed application.
The enclosure should have ventilation holes to prevent gas
build-up in the event of a leak. The deck ledges and counter
should be flat and level. (Refer to ANSI Z21.58 Standard for
Outdoor Cooking Gas Appliances, Section 1.7 Enclosures
For Self Contained LP-Gas Supply Systems or local codes
for additional information.)
Minimum clearance from the sides and back of the accessory to adjacent combustible construction below the top of
unit are 12” from the sides and back.
Dégagement minimal entre les parois latérales et l’arrière
de l’appariel et la construction combustible au-dessous
du panneau supérieur de l’appareil (30 cm à partir des
parois latérales et 30 cm à partir de l’arrière).
Minimum clearance from sides and back of unit to adjacent
combustible construction extending above the unit is 18”
from the sides and back.
Dégagement horizontal minimal entre les parois latérales et l’arrière de l’appariel et la construction verticale
combustible au-dessus de l’appareil (45.7 cm à partir des
parois latérales et 45.7 cm à partir de l’arrière).
Do not use this appliance under overhead combustible
surfaces.
Ne pas utiliser cet appareil sous une surface combustible.
The grill accessory may be powered from either a 120 volt,
60 hertz, 15 amp GFI certified outlet installed by a qualified
electrician OR it may be powered directly from your Lynx
Grill transformer power supply.
When a Lynx grill is not available or if the grill is not located
close enough to the grill a Lynx LASK (Lynx Accessory Switch
Kit) is available as an optional purchase.
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
15
|
Page 16
WARNING
Never connect a gas line directly to the accessory. A pressure regulator must be installed on all gas equipment.
All local codes require it and Lynx supplies the correct regulator with your accessory. Removing or failing to install
the pressure regulator can result in fire and serious personal injury and will void the warranty.
Gas PlumbinG
Gas & electric connections
Keep last two
threads clean
The accessory is factory set to use either propane (LP) or
natural gas (NAT). It is critical that the gas you use matches
that which the accessory was set up for. You can verify that
by checking the rating plate.
The rating plate is located on the heat shield behind the
front panel.
Ensure that the gas supplied meets with the minimum pressure requirements.
Do not operate the accessory on any gas other than that for
which the accessory has been set.
Fuel WC Max Inlet WC Min Under Full
Load
Nat Gas 7 in 4 in
LP 14 in 10 in
NATURAL GAS
Lynx recommends that only qualified professionals perform
the required plumbing on this product.
The gas supply line must be sized to accommodate the
total BTU requirements of all the gas-fired equipment that
will be connected to that line.
In no case should pipe less than 3/4” inside diameter or 1”
outside diameter be used.
•Calculate the total BTU output of all equipment and
refer to “INDEX: Gas Supply Line Runs” for allowable run
distances. Failure to meet these minimum requirements
may reduce performance of the accessory and any other
appliances running on that supply line.
•Always keep supply line runs as short as possible. (See
INDEX: “Gas Supply line runs”)
•A gas shut-off valve must be installed in an easily accessible location by a qualified plumber.
Water Column Requirements
Both the regulator and the manifold orifices have been
tuned for the type of gas specified on the rating plate.
Converting to a different type of gas requires a conversion
kit which is included with your side burner accessory and
must be installed by a qualified technician.
All installation and all installation parts must conform to
local codes with the National Electrical Code, ANSI/NFPA
70-1990 and the National Fuel Gas Code, ANSI Z223.1/
NFPA 54 in the U.S. and CGA-B149.1/.2 in Canada.
Canadian installations must conform to CGA-B149.1/.2
natural gas/propane installation code. (Canada)
16
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
|
•Keep any threading compound off of the first two pipe
threads to avoid having any small pieces of compound
break loose and clog a burner valve or orifice. Do not put
sealant on any male end of flare fittings.
For built-in installations, it is recommended that any flexible
pipe used be kept as short as possible. (See INDEX: “Gas
Connections” for typical permanent hook up.)
Page 17
LP Gas
Accessories set up for LP gas come equipped with an LP
hose/ regulator assembly for connection to a standard 20 lb.
LP cylinder. (Type 1).
All fittings necessary to attach the assembly to the accessory
are included.
Permanently plumbed LP connections, such as those in
line with a bulk cylinder, require a 4/11 regulator. (Lynx P/N
30781)
When using the 4/11 regulator you must ensure that it is
set for the proper fuel type. This is done by removing the
regulator cap and gasket and looking at the bottom of the
plunger to see what fuel type is visible. This is the regula-
tor fuel setting. NAT is for natural gas and LP is for propane
gas. The LP setting can be further identified by the large
diameter disk on the bottom of the plunger. To change from
one gas to the other simply push the plunger to the side
to snap it out of the cap, turn the plunger so it reads the
desired gas type on the bottom, and push the plunger until
it snaps back into place in the cap then replace the cap into
the regulator.
Never connect an unregulated gas line to the grill.
When exchanging your cylinder for a refill, exchange only
for a Type 1 20lb cylinder with an over-fill protection device.
Never use a cylinder with a damaged valve.
A dented or rusty LP cylinder may be hazardous and should
be avoided. If in doubt, have it checked by your LP supplier.
Always check for leaks after every LP cylinder change. (See
INDEX: “Leak Testing” for further details.)
Always shut off the LP-gas supply at the cylinder when the
accessory is not in use.
Cylinders must be stored outdoors in a well-ventilated area
out of the reach of children. If your accessory is stored in-
doors, the LP cylinder must be stored outside.
LP ConneCtions
Make sure the LP cylinder valve is fully closed. It is possible for
the valve to be open without releasing gas but, as soon as you
start connecting the regulator, gas will leak from the connec-
tion.
Insert the regulator inlet into the cylinder valve and turn the
black coupler clockwise until the coupler is hand tight. Do not
over-tighten this connection.
To disconnect the coupler, first make sure the main cylinder
valve is turned off. Grasp the coupler and turn counter clock-
wise. Always leak-test the connection after refilling or exchang-
ing LP cylinders. (See INDEX: “Leak Testing” for further details.)
Gas & electric connections ...continued
LP cylinder with type 1 valve connection
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
17
|
Page 18
PROPANE HOOK UP NATURAL GAS HOOK UP
Gas & electric connections ...continued
COLD WEATHER WARNING: PROPANE
Extremely cold temperatures may cause your burner
to light inside the burner instead of outside. Once
lit, if you hear a ‘whooshing’ sound, immediately
turn the burner knob off to extinguish the flame and
then immediately re-light the burner.
propAne hook up nAturAl gAs hook up
WARNING
18
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
|
MAXIMUM RUNS FOR ALL
APPLIANCES ON SUPPLY LINE
Run Length
3/4” Pipe (in feet)
10 360,000
20 245,000
30 198,000
40 169,000
50 150,000
60 135,000
70 123,000
80 115,000
Max BTU for all
Appliances on line
Page 19
OPTIONAL ELECTRICAL KITS
ElEctrical connEctions
Each accessory includes 6 feet of wiring (coiled inside the back of the accessory) to connect the accessory to a Lynx grill.
Additionally, Lynx manufactures 2 specialized electrical kits that you may purchase for your accessory, depending upon
how it will be installed. Each electrical kit ships with an instructional sheet for assembly. Assembly instructions and schematics/drawings can also be found on our website at www.lynxgrills.com
.
•LASK Lynx Accessory Switch Kit
•LPEK Lynx Power Extension Kit
Installation requires an outdoor 120VAC 15A GFI (Ground
Fault Interrupter) electrical outlet adjacent to the accessory.
The GFI outlet features an internal breaker that reduces
shock hazard. This type of outlet should be installed by a
qualified electrician either inside the island enclosure for
built-in units, or near the location where a free-standing unit
will be used.
For built-in accessories, the supplied 12V transformer is
connected to the accessory during installation.
If the electrical system fails to operate, a connection may
have come loose in shipping or the GFI may have tripped,
requiring a reset. See the Troubleshooting section for more
details.
This switch and transformer kit allows independent control of a Lynx accessory
burner without connection to a grill. The kit contains a transformer and mounting
bracket as well as a switch assembly with a mounting plate. The kit also contains
a wiring harness to adapt an L series accessory to an M series switch and transformer.
The Lynx Power Extension Kit provides 12 feet of additional wire between your
Lynx Grill and accessory burner.
CONNECTING THE WIRING
The accessory electrical harnesses are designed to provide
power for both ignition and lighting. While ignition is controlled at the accessory, lighting is controlled at the grill.
You can control lighting at the accessory by installing the
Lynx Accessory Light Switch (LASK).
Disconnect the 4-pin connector on the grill and connect
those plugs to the mating plugs on your accessory. (See
Index “Electrical Connections)
Important note: If using multiple Lynx accessories with the
Control Illumination/Blue LED’S, a connector for this purpose is built into the accessory wiring. This will allow you to
use the light switch on your Lynx grill to actuate the power
on more than one accessory.
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
19
|
Page 20
TesTing The insTallaTion
Before turning the gas supply on, check for proper installa-
tion using the following test:
1. Plug the transformer back into the receptacle.
2. Push in the gas control knob on your accessory and
watch the igniter. It should glow bright and steady.
3. Turn on the light switch on the grill. Both the grill and
the grill accessory lights should operate together. This
indicates a proper assembly.
Turn the gas on to all appliances.
4. Perform a leak test if you have not done so since
plumbing the unit.
5. Check all burners for proper ignition. Refer to the Light-
ing Instructions for Side Burners.
Leak TesTing
Leak Test Procedure:
1. Create a soapy solution of 1 part soap and 3 parts
water.
2. Confirm that all control knobs are in the off position.
3. Turn on the fuel supply. For natural gas, turn the valve
handle 1/4 turn to align with the gas flow.
4. For LP, turn the cylinder valve knob counter clockwise
one full rotation.
5. Apply the soap solution generously by paint brush or
squirt bottle on all connections and fittings.
6. If bubbles appear to “grow” on any of the connections,
you have a gas leak. IMMEDIATELY turn off the gas
supply.
Fixing a gas Leak
To prevent fire or explosion hazard, DO NOT smoke
or allow any potential source of ignition (sparks,
electrical arcing, etc) in the area while performing a
leak test. Leak tests should be conducted outdoors
only. Never conduct a leak test using fire or flame.
1. Shut off the gas supply
2. Turn all grill controls to the “ON” position to purge the
grill of any gas build-up, then turn the controls back
“OFF”.
3. Wash off the soapy solution with cold water and dry.
4. Tighten the loose joint, or replace the faulty part with
manufacturer-recommended replacement parts.
5. DO NOT attempt to repair the LP cylinder valve if it is
damaged. The only way to safely resolve a damaged
cylinder is to REPLACE IT.
6. Repeat the leak test to ensure that no leaks are present.
DANGER!
20
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
|
Page 21
SCHEMATICS
WHITE
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
21
|
Page 22
The guides, measurements and dimensions detailed below are designated to assist you with planning your outdoor kitchen.
SPECIFICATIONS & INSTAllATION
NOTE: Due to continuing product innovation, specifications are subject to change without notice.
IMPORTANT: Please reference the Care & Use / Installation manual for details on gas plumbing requirements, electrical specifications and the
proper installation of your Lynx outdoor kitchen equipment. This manual can be downloaded from the Lynx website at www.lynxgrills.com
Grills
MODEL A B C
L27 26.00 10.88 22.00
L30 29.00 10.88 24.50
L36 35.00 10.13 22.00
L42 41.00 10.88 24.50
L54 53.00 10.88 24.50
coMpleMentarY proDucts
ACCESS DOORS
MODEL A B
LDR21-1 19.25 19.00
LDR27-1 25.25 19.00
LDR30-1 28.25 19.00
LDR36-2 34.25 19.00
LDR42-1 40.25 19.00
LDR36T 31.63 19.00
LDR42T 37.63 19.00
SIDE BURNERS
MODEL
LSB1 12.13 10.63 24.50
LSB2 12.13 10.63 24.50
LSB2PC 24.25 10.63 24.50
LPB 19.00 10.63 22.00
A B C
WitH insulateD jacKet installeD
MODEL A B C
LIJ27 33.00 11.63 24.00
LIJ30 36.00 11.63 26.50
LIJ36 42.00 11.63 24.00
LIJ42 48.00 11.63 26.50
LIJ54 60.00 11.63 26.50
STORAGE SYSTEMS
MODEL A B C
LSA30 28.25 19.00 24.50
LSA36 34.25 19.00 24.50
TRASH CENTERS
MODEL A B C
L18TC 16.00 24.00 13.00
L20TR 16.81 24.00 24.75
LTA530 28.25 19.00 20.00
3”
UTILITY DRAWERS
MODEL A B C
LUDE 12.13 19.25 24.00
LUDXL 17.25 18.57 24.25
LDW19 17.50 19.00 24.50
LMD 21.75 5.63 23.38
WARMING DRAWERS
MODEL A B C
L30WD 28.50 10.00 20.50
L42CC 40.25 19.38 24.50
COCKTAIL PRO
MODEL A B C
CS30 29.00 10.63 22.75
22
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
|
Only required if island counter top overhangs the face of the island
COUNTER TOP NOTCH DETAIL
AA
5”
4.5”
C
3”
B
Page 23
outDoor reFriGerators
1
1/8
” min. for model LUDE
3
1/2
” min. for model LUDXL
2
1/2
” min. for model LDR (access door)
* Cocktail Pro should have an open bottom for plumbing and drain access.
** 1” square hole must be located at rear of grill cutout. 120V GFI outlet must
be located within 6’ of the 1” hole.
1/2” NPT
gas connection
CLEARANCE
33
1/2
”
34”
15”
25”
ICE MACHINE
3”
2”Ø or 2” square holes
for manifold connection
(rear or bottom access)
12” min.
Grill**
Cocktail Pro*
Warming Drawer/
Convenience Center
Utility
Drawer
Side
Burner
Drop In
Cooler
(LDC18)
Access
Doors
A
B
2
1/4
”
3
1/2
”
3
1/4
” min.
2”
3” min.
C
Trash
Center
36
3/8
”
min.
3
1/2
”
8
1/4
”
18
1/4
”
6
1/4
”
18
1/4
”
Trash
Chute
(L18TS)
2
3/
16
''
13 ''
Single
Storage Drawer
3”
min.
14
1/2
''
8
1/4
''
Towel
Dispenser
(L16TWL)
A
A
A
A
A
B
B
B
B
A
B
B
A
min.
max.
a
e
d
f
c
b
SPECIFICATIONS & INSTAllATION
MODEL A B C D
L24REF 24.25 33.00 26.00 32.00
L24BF 24.25 34.50 26.00 34.25
L24DWR 24.25 34.50 26.00 34.25
L15ICE 15.25 34.00 26.00 33.50
A
C
B
A
C
B
D
D
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
23
|
Page 24
lYnX liMiteD WarrantY
I. Limited Lifetime Warranty
The stainless steel grill body, brass grill burners, ProSear™
burner and rotisserie infrared burner are warranted to be free
from defects in material and workmanship when subjected
to normal domestic use and service for the lifetime of the
original purchaser. This warranty excludes surface corrosion,
scratches, and discoloration which may occur during normal
use. This warranty is limited to the replacement of the defective parts, with the owner paying all other cost including
labor, shipping and handling.
II. Limited Five-Year Warranty
The following grill parts are warranted to be free from defects in material and workmanship, when subjected to normal
domestic use and service, for a period of five (5) years from
the original date of purchase; cooking grates, warming racks,
spit rods, briquette trays, manifolds and gas valves. This
warranty is limited to the replacement of the defective parts,
with the owner paying all other costs including labor, shipping, and handling.
III. Limited Two-Year Warranty
All other grill components are warranted to be free from defects in material and workmanship, when subjected to normal
domestic use and service, for a period of two (2) years from
the original date of purchase. This warranty is limited to the
replacement of the defective parts, with the owner paying all
other costs including labor, shipping and handling..
IV. Limited One-Year Warranty.
For a period of one (1) year from the original date of purchase, Lynx will replace or repair parts found to be defective
at no cost to the original purchaser. This includes the cost of
shipping replacement parts and, where necessary, service
labor at prevailing local rates by a Lynx authorized service
person. Service will be provided during normal business
hours and must be authorized in advance by Lynx.
IV. Limitations & Exclusions
1) This Warranty shall apply to products purchased and
located in the United States and Canada. Products must
be purchased in the country where service is requested.
2) Warranty applies only to the original purchaser and may
not be transferred.
3) Warranty is in lieu of all other warranties expressed or
implied and all other obligations or liabilities related to
the sale or use of its grill products.
4) Warranty shall not apply and Lynx is not responsible
for damage resulting from misuse, abuse, alteration of or
tampering with the appliance, accident, hostile environ ment, flare-up fires, improper installation, or installation
not in accordance with the instructions contained in
this manual, or the local codes.
5) Lynx shall not be liable for incidental, consequential,
special or contingent damages resulting from its breach
of this written warranty or any implied warranty.
6) Some states do not allow limitations on how long an
implied warranty lasts, or the exclusions of or limitations
on consequential damages. This warranty gives you
specific legal rights and you may have other rights which
vary from state to state.
7) No one has the authority to add to or vary Lynx’s warranty,
or to create for Lynx any other obligation or liability in
connection with the sale or use of its products.
8) Limited to the replacement of defective parts with the
owner paying all other costs including labor.
V. What is not covered: Lynx shall not be responsible for
and shall not pay for the following:
1) Installation or start-up, damages or problems caused by
improper installation or use;
2) Service by an unauthorized service provider;
3) Damage or repair due to service by an unauthorized
service provider or use of unauthorized parts;
4) Warranty does not apply to products installed in any
commercial or non-residential application. Examples
of excluded applications include, but are not limited
to day care centers, schools, bed and breakfast centers,
churches, private clubs, fire stations, club houses,
common areas in multi-family dwellings, restaurants,
hotels, nursing homes, food service locations and
institutional food service locations.
5) To correct normal adjustments or settings, due to
improper installation, commissioning or local gas supply
properties.
6) Shipping and handling costs, export duties, installation,
removal, or re-installation cost.
7) Display models are sold “as is”. If you have purchased a
display model, please be advised that it is sold “as is”
and that it is subject to the following warranty exclusions:
any exterior or cosmetic damage is non-warrantable; any
missing components will be replaced at consumer’s
expense; major handling damage to manifold, valve and
ignition system will be serviced at consumer’s expense; all
other warranty’s (standard warranty) will remain in effect.
8) The cost of a service call to diagnose trouble.
24
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
|
Page 25
lYnX coMMon area liMiteD WarrantY
The Lynx Limited Warranty covers residential installations
only and is non-transferable to any other party. This ‘nonresidential’ warranty applies when the product is installed in
common areas where more than a single party has rightful
access to its use or in locations considered beyond normal
residential use such as B&B’s, and private clubs.
THIS PROVISION EXCLUDES ALL COMMERCIAL APPLICATIONS, INCLUDING, BUT NOT LIMITED TO RESTAURANTS
AND INSTITUTIONAL FOOD SERVICE LOCATIONS.
I. Limited Five-Year Warranty
The stainless steel body housings, the solid brass grill burners are warranted to be free from defects in material and
workmanship when subjected to normal use and service for a
five year period from the original purchase date. This warranty excludes surface corrosion, scratches, and discoloration
which may occur during regular use. This warranty is limited
to the replacement of the defective parts, with the owner
paying all other cost including shipping, handling and labor.
II. Limited One-Year Warranty
The structural integrity of the interior grill parts, exterior, and
drip pans are warranted to be free from defects in material and workmanship, when subjected to normal domestic
use and service, for a period of one year from the date of
purchase. This warranty is limited to the replacement of the
defective parts, with the owner paying all other costs including labor.
III. Limited Parts & Labor Warranty
All other grill components are warranted to be free from
defects in material and workmanship for a period of 90
days from the original date of purchase. Lynx will replace or
repair parts found to be defective at no cost to the original
purchaser. After the 90 day period Lynx will sell parts to the
holder of this warranty at Lynx contractor prices for an additional 9 months.
IV. Limitations & Exclusions
1) This Warranty shall apply to products purchased and
located in the United States and Canada. Products must
be purchased in the country where service is requested.
ment, flare-up fires, improper installation, or installation
not in accordance with the instructions contained in this
manual, or the local codes.
5) Lynx shall not be liable for incidental, consequential,
special or contingent damages resulting from its breach
of this written warranty or any implied warranty.
6) Some states do not allow limitations on how long an
implied warranty lasts, or the exclusions of or limitations
on consequential damages. This warranty gives you
specific legal rights and you may have other rights which
vary from state to state.
7) No one has the authority to add to or vary Lynx’s warranty,
or to create for Lynx any other obligation or liability in
connection with the sale or use of its products.
8) Limited to the replacement of defective parts with the
owner paying all other costs including labor.
V. What is not covered: Lynx shall not be responsible for
and shall not pay for the following:
1) Installation or start-up, damages or problems caused by
improper installation or use;
2) Service by an unauthorized service provider;
3) Damage or repair due to service by an unauthorized
service provider or use of unauthorized parts;
4) To correct normal adjustments or settings, due to
improper installation, commissioning or local gas supply
properties;
5) Shipping and handling costs, export duties, installation,
removal, or re-installation cost.
6) Display models are generally sold “as is.” If you have
purchased a display model, please be advised that it is
sold “as is” and that it is subject to the following warranty
exclusions: any exterior or cosmetic damage is non warrantable; any missing components will be replaced at
consumer’s expense; major handling damage to
manifold, valve and ignition system will be serviced at
consumer’s expense; all other warranty’s (standard
warranty) will remain in effect.
2) Warranty applies only to the original location of installa tion and may not be transferred.
3) Warranty is in lieu of all other warranties expressed or
implied and all other obligations or liabilities related to
the sale or use of its grill products.
4) Warranty shall not apply and Lynx is not responsible
for damage resulting from misuse, abuse, alteration of or
tampering with the appliance, accident, hostile environ-
7) The cost of a service call to diagnose trouble.
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
25
|
Page 26
siDe Burner eXploDeD parts VieW
MODEL INNER BURNER OUTER BURNER OPEN TOP BURNER TOTAL INPUT
LPB 13,000 34,000 47,000 BTU/Hr
LSB2PC 2 @ 15,000 30,000 BTU/Hr
LCB1 1 @ 15,000 15,000 BTU/Hr
LCB2 2 @ 15,000 30,000 BTU/Hr
26
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
|
MODEL-SPECIFIC BTU OUTPUTS
Page 27
inDeX
A
Adjusting:
Low Heat Adjustment .................................................... 12
Power Burner Air Shutter ............................................... 10
Air Shutter Adjustment .................................................. 10
C
Code Requirements ....................................................... 14
Cold Weather Use ..........................................................18
Connections:
Electrical ........................................................................ 19
Gas ............................................................................ 16
Optional Electrical Kits .................................................. 19
Contacting LYNX ........................................................... 13
D
Damage:
Shipment ....................................................................... 14
E
Electrical Connections ................................................... 19
Exploded Parts View ...................................................... 26
G
Gas Connections ........................................................... 16
Gas Leaks, Testing for .................................................... 20
Gas Pressure Specs ....................................................... 16
Gas Requirements ......................................................... 16
Gas Supply Line Runs .................................................... 18
Grilling in Windy Conditions ........................................... 7
O
Obtaining Service .......................................................... 13
Optional Electrical Kits .................................................. 19
P
Propane Hook Up .......................................................... 18
Purging the Gas Lines ................................................... 11
S
Schematics ..................................................................... 21
Serial Number, Location ................................................ 13
Service, Contacting Lynx ............................................... 13
Specications:
Code Requirements ....................................................... 14
Gas Pressure .................................................................. 16
Natural Gas Hook Up .................................................... 18
Propane Hook Up .......................................................... 18
Supply Line Runs ........................................................... 18
T
Technical Support .......................................................... 13
Testing:
Leak Testing ................................................................... 20
The Installation .............................................................. 20
W
Warranty:
Limited ........................................................................... 24
Common Area Limited .................................................. 25
L
Leak testing ................................................................... 20
Lighting the Burner........................................................ 11
Lighting with a Match .................................................... 11
Locating:
Serial Number ............................................................... 13
LP Connections ............................................................. 17
M
Manual Lighting ............................................................. 11
Maximum Supply Line Runs .......................................... 18
N
Natural Gas Hook Up .................................................... 18
SIDE BURNER ACCESSORY CARE & USE/INSTALLATION
27
|
Page 28
Lynx Professional Grills
5895 Rickenbacker Rd.
Commerce, CA 90040
Service: (888) Buy-Lynx (888-289-5969)
Fax: (323) 838-1778
www.lynxgrills.com
Loading...