LVD P3D, L3D, V31 Installation Guide

LLVVDD CCOOMMPPAANNYY NNVV

1

LLVVDD CCAADDMMAAN

N

®

®

PP33DD // LL33DD

VV3311 SSeerrvveerr -- CClliieenntt IINNSSTTAALLLLAATTIIOONN GGUUIIDDEE

MMaarrcchh 22001133

LLVVDD CCOOMMPPAANNYY NNVV

2

Table of contents guide

 Page 2 : Table of Contents
 Page 3 : Introduction
 Page 4 : Installation requirements

- System requirements

 Page 8 to 30 : Server Installation
 Page 31 to 51 : Client PC Installation

 Page 54 : Software Support

(Guide 1 contains the standalone installation information!)

LLVVDD CCOOMMPPAANNYY NNVV

3

Introduction

Thank you for choosing CADMAN® P3D / L3D

This guide will assist you during the installation of the software.
Please take the time to read it carefully so you fully understand
the required actions you need to take during the installation.

Please ensure before starting that your system is operating in a
Stable way and that it is not infected with any virus – like
programs or processes.

If you are not familiar with basic windows commands please
contact
your system administrator to assist you.

Should you have any suggestions to improve this guide please
contact the LVD Company software division.

[e-mail]
[e-mail]

Should you find any error in this guide please contact the
LVD Company software support team to adjust the guide.

LLVVDD CCOOMMPPAANNYY NNVV

4

Supported workstation
operating systems

- Windows XP with Service Pack 3

- Windows Vista Home Premium

with Service Pack 2

- Windows Vista Business with

Service Pack 2

- Windows Vista Enterprise with

Service Pack 2

- Windows Vista Ultimate with

Service Pack 2

- Windows 7 Home Premium

- Windows 7 Professional

- Windows 7 Enterprise

- Windows 7 Ultimate

Supported server operating
systems (for database)

- Windows Server 2003

Enterprise edition SP1

- Windows Server 2008

- Windows Server 2008 R2

Supported SQL Versions

- SQL 2005 (Express, Workgroup,

Standard, Enterprise)

- SQL 2008 (Express, Workgroup,

Standard, Enterprise)

- SQL 2008 R2 (Express,

Workgroup, Standard,
Enterprise)

Installation requirements

Remark : 32 and 64 bit operating systems from the above are supported

LLVVDD CCOOMMPPAANNYY NNVV

5

Recommended
Hardware
Specifications

- Intel or AMD Quad Core Processor

- 4Gb Ram

- Screen resolution of 1680*1050

- Graphics Card with 512mb is recommended

- 10Gb free hard disk space

- USB port for hardware dongle (in case of

updates a parallel port might still be
necessary)

- Internet explorer 7 or higher is required

- Administrator rights are needed for

installation

- TCP/IP must be configured correctly to run

a client installation

System requirements

NOTE: Before starting: Please ensure that the system is clean
from all virus like infections.

LLVVDD CCOOMMPPAANNYY NNVV

6

Different types of installation

1. When to install as server?

Install as server when you multiple licenses and you want this pc
to hold the database and the sql server. (make sure this pc is
performing well enough to maintain a good working speed.)
The server will share the database and the sql server so a fast
network connection is necessary (preferable a 100Mbit or better
connection.)

2. When to install as Client?

Install as client when you have already successfully setup a
server pc and you want to connect to this server.

During the installation several Message Boxes will be displayed.
Please read them carefully as they contain important
information for a successful installation.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

7

CA

CAD

Server-

Only PC

Client

PC

CAD

CAD

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

8

Pre – installation information

Steps to follow for this installation.
(All steps are explained in detail on the following pages.)

1. On the server
a. Installation of the SQL Server (Express version)
b. Installation of the Cadman P3D /L3D server files

2. On the client Pc’s
a. Installation of the Cadman P3D/L3D program
b. Creating the database.
c. Installation of the machine files.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

9

SQL Server (2005/2008) Express Installation

This installation will not cause any harm or incompatibility, when
you already have an existing SQL server installation.

Insert the LVD SQL CADMAN Server DVD in the DVD-Rom Drive.

If autorun is enabled, the following screen will appear.
If autorun is not enabled you can start the installer by browsing to
the cd via Windows Explorer and Double click on the
LVDCadmanServerSetup.exe file in the main folder of the CD.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

10

Following screen will appear:

SQL 2005 is selected by default.
In case of Windows 7, SQL 2008 is selected by default.

You are free to choose any version.

Click the CADMAN Server button to continue.

If you need to use a custom connection to this SQL :
<servername>\CADMAN as sql instance name
Login : sa
Password : Cadman@LVD2005 for SQL2005
Password : Cadman@LVD2008 for SQL2008
Do NOT select the SQL 2012 option.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

11

Following screen will appear:

(only when .NET Framework 2.0 wasn’t installed yet, if it was
already installed, this screen will not appear)

Click “next” to continue

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

12

Following screen will appear :

Enable the “I accept terms…” and then click “Install” to continue.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

13

Following screens will appear :

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

14

Click “Finish” to continue

If .NET framework was already installed, the system will proceed
immediately with this step.

System will now continue with the SQL Server installation.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

15

Following screen will appear:

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

16

Once this comes up, the server is ready !

You can close the remaining open windows. A reboot may be
necessary !

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

17

Server INSTALLATION

Insert the Cadman P3D / L3D in the DVD-rom drive.

Following screen will be displayed.

Choose Cadman® P3D/L3D., read the message box and press
“OK”

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

18

Following screen will be displayed.

Select Cadman® P/L setup, read the message box and press
“OK”

NOTE: When you are working under Windows XP or Windows
Vista, make sure you have full administrator rights. Else you can
not install the program.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

19

Next screen will be displayed.

Please select the desired language and continue the installation.

Fill in the company name and the last 6 digits of the serial
number from the wibukey dongle. (Printed on the dongle)

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

20

Following screen will be displayed.

Click next to continue.
Following screen will be displayed.

Choose the “accept” option and then click next to continue.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

21

Following screen will be displayed

For new installations, please use the “no, i want to make a clean
install” option.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

22

Following screen will be displayed.

Choose the installation directory. (It is recommended to keep the
default settings)

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

23

Following screen will be displayed.

Choose the destination folder. (It is recommended to keep the
default settings)

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

24

Following screen will be displayed.

Choose the installation type.

This guide describes the server installation, so please select the
server option.

Make sure that the “install database server” is NOT selected.

The other possibilities are explained in other installation guides.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

25

SERVER INSTALLATION (Continued)

Following screen will be displayed.

Following screen will be displayed.

Choose the desired

unit and select “next”

to continue.

Leave the options as default (only “LVD CadmanPL” selected)

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

26

Following screen will be displayed

Leave as default and select “next” to continue.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

27

Following screen will be displayed.

(You can see the overview of the selected type of installation and

installation settings in the “current settings” textbox.)
Press “Next” to continue the installation

Software will now start to install all necessary files …

During this you will be presented with various screens from
which you will see an example in chronologic following.

Please take note that this part of the installation can take up to
60 minutes depending of the speed of the Pc where the
installation is being made on.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

28

During the installation progress, different windows can popup.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

29

Once all files are installed, the system will ask for the password
file.

Following screen will be displayed.

On the server you don’t need the password. You may select “NO”

to continue

Click Finish to continue.

The Server installation is now finished.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

30

Client Pc Installation

Insert the Cadman P3D / L3D in the DVD-rom drive.

Following screen will be displayed.

Choose Cadman® P3D/L3D., read the message box and press
“OK”

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

31

Following screen will be displayed.

Select Cadman® P/L setup, read the message box and press
“OK”

NOTE: When you are working under Windows XP or Windows
Vista, make sure you have full administrator rights. Else you
cannot install the program.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

32

Next screen will be displayed.

Please select the desired language and continue the installation.

Fill in the company name and the last 6 digits of the serial
number from the wibukey dongle. (Printed on the dongle)

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

33

Following screen will be displayed.

Click next to continue.
Following screen will be displayed.

Choose the “accept” option and then click next to continue.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

34

Following screen will be displayed

For new installations, please use the “no, i want to make a clean
install” option.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

35

Following screen will be displayed.

Choose the installation directory. (It is recommended to keep the
default settings)

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

36

Following screen will be displayed.

Choose the destination folder. (It is recommended to keep the
default settings)

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

37

Following screen will be displayed.

Choose the installation type.

This guide describes the Client installation, so please select the
Client option. Then click Browse to select which pc is the
database server.

The other possibilities are explained in other installation guides.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

38

Once you selected the Browse button, you need to find your
database server on your network. Browse to it, and select it, then
click OK to confirm.

Click “next” to continue

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

39

CLIENT PC INSTALLATION (Continued)

Following screen will be displayed.

Following screen will be displayed

Choose the desired

unit and select “next”

to continue.

Leave the options as
default and select
“next” to continue

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

40

Following screen will be displayed

Leave as default and select “next” to continue.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

41

Following screen will be displayed.

(You can see the overview of the selected type of installation and
installation settings in the “current settings” textbox.)

Press “Next” to continue the installation

Software will now start to install all necessary files …

During this you will be presented with various screens from
which you will see an example in chronologic following.

Please take note that this part of the installation can take up to
60 minutes depending of the speed of the Pc where the
installation is being made on.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

42

During the installation progress, different windows can popup.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

43

Once all files are installed, the system will ask for the password
file.

Following screen will be displayed.

Select “YES” to install the key file.

The Key file is delivered on the USB stick in the package.
The file is located in the
\CADMAN-L3D\Password\<dongle number> folder for L3D
\CADMAN-P3D\Password\<dongle number> folder for P3D

(<Dongle number> will be the serial number of the dongle)

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

44

Once the password is installed, following screen will be
displayed.

Click Finish to continue.

Once you click finish, the actual installation of the program files
is ready. The system will now start with the database creation
process.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

45

Database creation:

Please select “create new database”

You can also do this step at any other time, to create a second
database, or to import/ move a database
You can do this by selecting :
“Start  all programs  Cadman  Configuration tool”

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

46

Select an appropriate name for your database and press “ok”

For the database name, please do not use special signs
(like @ ? ~ etc….) (Use Characters: A-Z, a-z, 0-9, ‘-‘)
Keep the name simple, for instance company name.

During installation a SQL instance was installed.
The instance name is : CADMAN
Login = sa
Password = Cadman@LVD2005 (for SQL 2005)
Password = Cadman@LVD2008 (for SQL 2008)

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

47

The system will now create your database. This can take several
minutes to complete.

If everything is ok, following message will popup.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

48

Installation of the machine configuration.

When you have created an empty database (see previous page)
you need to install the machine configuration files.
You need to do this step on ALL client pc’s.

Before you install the machine configuration file please close the
Cadman P3D / L3D Software.

Insert the installation cd.

Select CADMAN P3D/L3D

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

49

Following screen will be displayed.

Select
postprocessor
setup.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

50

Following screen will appear.

Press the

“SETUP”

button.

Setup will now install the machine. This only takes a few seconds
up to one minute. Once the screen disappears, you can start the
software and all of the machine configuration will be installed.

If the system cannot find the setup file, you can find it on the
USB stick delivered with the package in the
Cadman L3D-P3D\Machines\<machine serial> folder

Should this message appear, press the “YES to all” button.

If you have multiple machines, the system will detect it and
install them one by one in the correct order.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

51

Wibukey setup (see also in the wibukey installation guide)

When the software is installed and the pc is rebooted it is now
the time to attach the Wibukey.

After attaching the key to the port, your windows operating
system will come up with the message to install the necessary
drivers (Plug and Play windows feature). (this only applies to USB
dongles !)

Parallel keys do not need these steps. only attach to the port.

Leave to the “recommended”

setting. (Automatically install
the software)

Press “next” to continue.

Your windows system is now
searching for the driver. (This
can take several minutes
depending on the speed of the
computer.

SSTTAANNDDAALLOONNEE IINNSSTTAALLLLAATTIIOONN

52

Select the driver that is
located in the windows
directory.

Press “next” to continue.

Finished installing the
USB drivers.

Press “finish” to quit.

NOTE: When attaching the USB dongle to any other free USB port
on which the dongle was not attached before, these steps will
need to be repeated.

SSOOFFTTWWAARREE SSUUPPPPOORRTT

53

SOFTWARE SUPPORT

If you need for any reason support for installing the software you
can contact LVD software support thru the following channels.

World Wide Software support :
Tel : [phone]
Fax : Fax: [phone]
E-mail : [e-mail]

Software support region America :
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]

For support please provide us with the following info :

- Company name

- Wibukey serial nr

- Machine serial nr

- Detailed description of the problem

- Contact e-mail address

This document is the property of LVD, no reproduction or access to third party
is allowed without written permission.