Lutron Electronics D-600P, D-600R, D-603P, DNG-600P, DNG-603P Installation Manual

English

Incandescent /

Halogen

120 V~ Dimmer

Rated at 120 V~ 60 Hz

Models:

600 W			1000 W		S-1000
D-600P	DVSC-603P	S-600	AY-10P	DW-10P
D-600R	DVW-600P	S-600P	AY-10PNL	DW-103P	S-103P
D-603P	DVW-603P	S-600PNL	AY-103P	GL-10P	S-103PNL
DNG-600P	GL-600	S-603P	AY-103PNL	GL-1000	TG-10P
DNG-603P	GL-600P	S-603PNL	DV-10P	GL-103P	TG-10PNL
DV-600P	GL-603P	SW-600	DV-103P	LT-103P	TG-103P
DV-603P	LT-600	SW-600P	DVSC-10P	S-10P
DVSC-600P	LT-603P	SW-603P	DVSC-103P	S-10PNL

Important Notes Please read before installing.

P/N 0301689

•Easy-to-follow

•Instrucciones Fáciles de Seguir

•InstruccionesFácilesdeSeguir •Easy-to-follow

P/N0301689

Multigang Installations

1.CAUTION: Use only with permanently-installed 120 V~ incandescent or halogen fixtures. To avoid overheating and possible damage to other equipment, do not use to control receptacles, fluorescent lighting fixtures, motor-driven appliances, or transformer-supplied appliances.

2.Install in accordance with all national and local electrical codes.

3.Only one dimmer can be used in a 3-way circuit.

4.When no “grounding means” exist within the wallbox then NEC® 2008, Article 404.9 allows a dimmer without a grounding connection to be installed as a replacement, as long as a plastic, noncombustible wallplate is used. For this type of installation, cap or remove the green ground wire on the dimmer and use an appropriate wallplate such as Lutron's Claro® or Fassada® series wallplates.

5.For new installations, install a test switch before installing the dimmer.

6.Protect dimmer from dust and dirt when painting or spackling.

7.Recommended minimum load is 40 W.

8.It is normal for the dimmer to feel warm to the touch during operation.

9.Clean dimmer with a soft damp cloth only. Do not use any chemical cleaners.

	When installing more than one control in the same wallbox,			Do Not Remove
	it may be necessary to remove all inner side sections prior			Outside Sections
	to wiring (see diagram). If pre-installed, remove the Lutron
	wallplate and wallplate adapter from dimmer. Using pliers,
	bend side section up and down until they break off. Repeat
	for each side section to be removed. Removal of dimmer
	side sections reduces maximum load capacity. Refer to chart
	below for maximum dimmer capacity.		Each Control Has Inside	Middle Control Has Two Side
	Dimmer Capacity Chart
			Sections Removed	Sections Removed
	Dimmer Rating	No sides removed	1 side removed	2 sides removed
	600 W	600 W	500 W	400 W
	1000 W	1000 W	800 W	650 W

?	Technical Assistance
	you have questions concerning the installation or operation of this product, call the
	Lutron Technical Support Center. Please provide exact model number when calling.
	U.S.A. and Canada (24 hrs/7days)	Fax [phone]
	+1.800.523.9466
	México	http://www.lutron.com
	+1.888.235.2910

Other countries 8am – 8pm ET +1.610.282.3800

Limited Warranty

Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture within one year after purchase. For warranty service, return unit to place of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA 18036-1299, postage pre-paid.

This warranty is in lieu of all other express warranties, and the implied warranty of merchantability is limited to one year from purchase. This warranty does not cover the cost of installation, removal or reinstallation, or damage resulting from misuse, abuse, or damage from improper wiring or installation. This warranty does not cover incidental or consequential damages. LUTRON’S LIABILITY ON ANY CLAIM FOR DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE MANUFACTURE, SALE, INSTALLATION, DELIVERY, OR USE OF THE UNIT SHALL NEVER EXCEED THE PURCHASE PRICE OF THE UNIT.

This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitation on how long an implied warranty may last, so the above limitations may not apply to you.

NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts. Lutron, Claro, Fassada, and Glyder are registered trademarks of Lutron Electronics Co., Inc. © 2013 Lutron Electronics Co., Inc.

Lutron Electronics Co., Inc.

7200 Suter Road

Coopersburg, PA 18036-1299, U.S.A.

P/N 0301689 Rev. A

Lutron Technical Support Center				1.800.523.9466	24 hrs / 7 days		www.lutron.com
Installation					5	Wiring the Dimmer.
1
	Turning OFF Power.					• For installations involving more than one control in a wallbox,
						refer to the section on Multigang Installations before beginning.
	• Turn power OFF at circuit breaker (or remove fuse).
	ON ON	OFF OFF	Warning: Shock Hazard. May result in serious			Dimmer wire location may vary by model number.
			injury or death. Turn off power at circuit			NOTE: Reference wires by color, not backcover location.
		OFF	breaker before installing the unit.

2	Removing Wallplate and Switch.
	• Remove wallplate and switch mounting screws.
	• Carefully remove switch from wall (do not remove wires).
	Caution: Verify
	power is OFF to
	switch before
	proceeding.

3 Identifying the Type of Circuit.

Different-colored screw (Common). Actual location may vary.

OR

Ground (Bare

Copper or

Green Wire)

Ground (Bare Copper
or Green Wire)			Tag
SINGLE-POLE:		3-WAY:
Insulated wires connected		Insulated wires connected to three screws. One of
to two screws of the	OR	these wires is connected to a screw of a different-
same color. Replace with		color (not green) or labeled COMMON. MARK or
a SINGLE-POLE dimmer.		TAG this wire to identify it when wiring. Replace
See Step 5a.		with a 3-WAY dimmer. See Step 5b.

4 Disconnecting Switch Wires.

Important Note: Your wall switch may have two wires attached to the same screw (see illustrations below for examples). Tape these two wires together before disconnecting. If your switch has two wires attached to the same terminal, connect both wires to the Dimmer terminal in Step 5.

One wire in the	One continuous
backwired hole	wire to the
and one to the	screw.
screw.

Screw Terminals:	Push-in Terminals:	Looped Wire:
Turn screws to loosen.	Insert screwdriver. Pull	Turn screw to loosen.
	wire out.

5a - Single-Pole Wiring

Black

Green or Bare		Ground
	Black	Black
Green or Bare
120 V
60 Hz	Ground	Light

•Connect the green or bare dimmer ground wire to the green or bare copper ground wire in the wallbox. (See Important Note 4.)

•Connect one of the black dimmer wires to either of the wires removed from the switch.

•Connect the remaining black dimmer wire to the other wire removed from the switch.

Note: To use a 3-Way dimmer (one black and two red wires) in a single-pole application, cap off one of the red wires and

follow instructions for single-pole wiring. (If the on/off switch works backwards, switch the red wires.)

	5b - 3-Way Wiring				• NOTE: Only one dimmer can be
			Tag
		Black				used in a 3-WAY circuit.
					• Connect the green or bare
						dimmer ground wire to the green
						or bare copper ground wire in the
						wallbox. (See Important Note 4.)
					• Connect the black dimmer wire
						to the wire removed from the
	Green					different-colored screw on the
						switch (marked or tagged wire).
	or Bare	Red		Ground	• Connect one of the red dimmer
		Black	Red			wires to either of the remaining
	Green or Bare		Red			wires removed from the switch.
					•	Connect the remaining red
	120 V	Dimmer		3-Way Switch
						dimmer wire to the remaining wire
	60 Hz	Ground		Light		removed from the switch.

6 Mount Dimmer to Wallbox. traditional style
				Note: To install a
	• Form wires carefully into the wallbox,			wallplate, firmly pull
	mount and align dimmer.			the Glyder® or Rotary
				knob to remove it.
	• Install wallplate.
				Install the wallplate
				and re-attach the knob.
	Start screws.			Glyder®
			Align dimmer and
			tighten screws.
7	Turning ON Power.			Rotary
	• Turn power ON at circuit breaker
	(or replace fuse).	ON	OFF

ON	OFF
ON	OFF