Lutron Electronics CS-YJ-4GC-WH Setup Manual

Shading Solutions

4-Group RF Remote Control

LED FLASHING

LED FLASHING

LED FLASHING

LED ON LED FLASHING

Models CS-YJ-4GC-WH, CS-YK-4GC-WH • Setup Guide—Please Read Before Operating

• This setup guide provides basic instructions for assigning and using the Lutron® 4-Group RF Remote Control with Lutron® shade products in stand-alone applications.

Device Description Assignment to Lutron® Window Treatments

• To assign and use the remote control in a RadioRA

• To assign and use the remote control in a HomeWorks

Models: CS-YJ-4GC-WH, CS-YK-4GC-WH

• To use the remote control with Lutron

® Smart Bridge, use the Lutron® App.

3 V- 50 mA

The Lutron® 4-Group RF remote control is a flexible and easy to use
device that allows the user to control Lutron® wireless shades from
anywhere in the space. This battery-operated control requires no
external power or communication wiring.

• Provides control of Lutron

® shades in the following systems:

Assignment to a Serena® or Sivoia® QS Triathlon® Shade

Honeycomb Roller

– Standalone

 Serena® RF Remote Control Honeycomb and Roller Shades

® QS Triathlon® Honeycomb and Roller Shades

 Sivoia
 Sivoia

® QS Wireless shades

– HomeWorks

® QS systems (CS-YJ-4GC-WH only)

1. Tap the Shade button.

– RadioRA® 2 systems (CS-YJ-4GC-WH only)
– Lutron® Smart Bridge (CS-YJ-4GC-WH only)

• Battery-powered; requires no wiring

• Backlit buttons clearly indicate which Shade Group is selected

• 7-year battery life (two AAA alkaline batteries included)

Removing and changing Shade Group assignments:

a. To remove the assignment of a particular shade to a Shade Group button, restore the shade to its factory default settings according to the instructions

included with the shade.

® 2 system, use the RadioRA® 2 Essentials or Inclusive software.

® QS system, use the HomeWorks® QS Design and Programming software.

LED ON

2. The Shade button
illuminates.

3. Choose a Shade Group
button. Press and hold.

LED FLASHING

4. The Shade
button flashes.
Assignment is
complete.

5. Repeat for
additional
shade/control
assignments.

Equipped with Sivoia® QS Wireless RF Receiver

Before starting, verify that the device
drive LED is OFF, and the window
treatment is positioned at its Open Limit.
If the LED is illuminated, tap the drive’s

button. The LED will turn off.

Open

1. Press and hold the device drive’s

2. The drive LED flashes, then stays

button.

Open

on. Release the Open

button.

b. To change the Shade Group button to which a particular shade is assigned, follow step a. above to remove the original assignment, then follow the

steps under Assignment to a Serena® or Sivoia® QS Triathlon® Shade, and choose a different Shade Group button at step 3.

English

LED OFF

LED FLASHING

Open button

Tap once: shade

opens to its upper limit

Close button

Tap once: shade

closes to its lower limit

Shade Group

buttons

Tap once to select

shades assigned to

the corresponding

group (number)

The Lutron® 4-Group RF remote control
is safe for use around baths and spas.

NOTICE: DO NOT submerge in water.

Raise & Lower
buttons

Press and hold to
move the shade

Favorite button

Tap once to move
the shade to a
favorite position

All Shades
button

Tap once to select
all shades

Setting or Adjusting Serena® or Sivoia® QS Triathlon® Shade Limits

Honeycomb Roller

LED ON

1. Tap the Shade button.

5. Use the Raise and Lower buttons
to position the shade at the
preferred upper or lower limit.

2. The Shade button
illuminates.

SET UPPER LIMIT

6.
With the shade at the

preferred upper limit, press

and hold the Open button.

3. Press and hold the Open
and Raise buttons.

OR

Setting a Serena® or Sivoia® QS Triathlon® Shade Favorite Level

IMPORTANT: The Favorite Level
function applies to Shade Groups.

• An individual Favorite Level can be

set for each of the 4 Shade Groups.

• A 5th Favorite Level can be set for

All Shades.

• A shade that belongs to multiple

groups will move to the Favorite
Level set for the Shade Group that
is active when the Favorite button
is pressed.

1. Tap the desired Shade
Group button or the
All Shades button.

2. Use the Raise and Lower
buttons to position the
shade(s) at the desired
favorite level.

SET LOWER LIMIT

With the shade at the

preferred lower limit,

press and hold the

Close button.

3. Press and hold the
Favorite button.

LED FLASHING LED ON

4. The Shade button
flashes, then
stays on.

7. The Shade button
flashes. Limit set
is complete.

4. The Shade button
of each shade in
the active Shade
Group flashes.
Favorite level is set.

3. Tap the device drive’s button
(arrow button next to the LED).

4. The device drive and wireless receiver
are in assignment mode, with LED’s
flashing every 4 seconds.

LED FLASHING

LED FLASHING

5. Choose a Shade Group button. Press and hold for
5 seconds.

The window treatment(s) will move a short distance
or “wiggle,” confirming successful assignment.

6. Repeat steps 1 through 5 for additional
shades/groups to be assigned.

Removing and changing Shade Group assignments:

a. To remove the assignment of a window treatment to a Shade

Group button, restore the device drive to its factory default settings
according to the instructions included with the window treatment.

b. To change the Shade Group button to which a particular device is

assigned, follow step a. above to remove the original assignment,
then follow the steps under Assignment to Lutron® Window
Treatments Equipped with Sivoia® QS Wireless RF Receiver, and
choose a different Shade Group button at step 5.

Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.

02/2015
P/N 045411 Rev. D

Lutron, O, Serena, Sivoia, Triathlon, HomeWorks, and RadioRA are registered trademarks of Lutron Electronics Co., Inc.

Shading Solutions

4-Group RF Remote Control

Models CS-YJ-4GC-WH, CS-YK-4GC-WH • Setup Guide—Please Read Before Operating

English

Battery Replacement

The Lutron® 4-Group RF remote control uses 2 AAA alkaline
batteries which are pre-installed.

For longest battery life, alkaline batteries are recommended.

To replace batteries:

1. Remove the battery cover
from the back of the control

Press here

Slide the

battery

cover off

2. Replace with 2 AAA alkaline
batteries, oriented as shown

Restore Factory Default Settings Limited Warranty

Note: Returning the Lutron® 4-Group RF remote control to its factory

default settings will remove all shade assignments and erase all
programming from the control.

Step 1: Tap the All Shades button.
Step 2: Tap the Open or Close button 3 times, (triple-tap), then press and

hold. The All Shades button LED will illuminate and stay on for
approximately 3 to 5 seconds while you continue to hold.

Step 3: Keep the button pressed until the All Shades button LED turns

off.

Step 4: Release the button and immediately triple-tap it again; (do not

hold). The LED’s of Shade Group buttons 1 - 4, and the All
Shades button will illuminate and stay on for approximately
3 to 5 seconds. When all LED’s turn off, the control has been
restored to factory default settings.

Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture
within one year after purchase. For warranty service, return unit to place of purchase or call
Lutron Customer Service at 1.888.LUTRON1.

This warranty is in lieu of all other express warranties, and the implied warranty of merchant­ability is limited to one year from purchase. This warranty does not cover the cost of installation,
removal, or reinstallation, or damage resulting from misuse, abuse, or damage from improper
wiring or installation. This warranty does not cover incidental or consequential damages.

LUTRON’S LIABILITY ON ANY CLAIM FOR DAMAGES ARISING OUT OF OR IN CONNECTION
WITH THE MANUFACTURE, SALE, INSTALLATION, DELIVERY, OR USE OF THE UNIT SHALL
NEVER EXCEED THE PURCHASE PRICE OF THE UNIT.

This warranty gives you specifi c legal rights, and you may have other rights which vary from
state to state. Some states do not allow the exclusion or limitation of incidental or consequential
damages, or limitation on how long an implied warranty may last, so the above limitations may
not apply to you.

©2014 Lutron Electronics Co., Inc.

FCC/IC Information

Troubleshooting

Symptom Probable Cause and Action

Buttons don’t light up
when they are pressed.

A specifi c window
treatment does not
respond when a button
is pressed.

Individual Shade
Groups respond, but
the All Shades button
does not work

Dead, low, or no batteries in wireless control.

• Install new batteries.
Batteries are installed incorrectly

(reversed polarity).

• Install batteries as indicated under Battery

Replacement.

The window treatment is not assigned to the
control.

• Follow the instructions under Assignment to

a Serena

® or Sivoia® QS Triathlon® Shade.

Devices are out of range.

• Check to make sure the remote control and
window treatments are within 30 ft (9 m) of
each other.

Repeat group assignment and select the All
Shades button.

This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation. Modifi cations not expressly approved by Lutron Electronics Co., Inc. could void the
user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected

• Consult the dealer or an experienced radio/TV technician for help

CE Information

For model number: CS-YK-4GC-WH
Lutron Electronics hereby declares that the models listed above are in
compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC. A copy of the DoC can be obtained by writing to:
Lutron Electronics Co., Inc., 7200 Suter Road, Coopersburg, PA 18036 U.S.A.

3. Reinstall the
battery cover

Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.

02/2015
P/N 045411 Rev. D

For Assistance:

WORLD
HEADQUARTERS

Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036
United States
Tel: [phone]
Fax:[phone]

CUSTOMER
SERVICE/ORDERING

USA: 1.888.588.7661

08.00 - 20.00 EST
UK: +44-(0)20.7702.0657

09.00 - 18.00 GMT

TECHNICAL SUPPORT

USA: 1.800.523.9466
24 hours/7 days
UK:+44.(0)20.7702.0657

09.00 - 18.00 GMT

INTERNET:

www.lutron.com
www.forums.lutron.com
[e-mail]

UNITED KINGDOM

Lutron EA Ltd. - London
Lutron House
6 Sovereign Close
Wapping, London E1W 3JF
England
Phone: [phone]
Toll Free (In-country only):

0800.282.107
Fax: [phone]
[e-mail]

Lutron, O, Serena, Sivoia, Triathlon, HomeWorks, and RadioRA are registered trademarks of Lutron Electronics Co., Inc.