Page 1
®
HomeWorks LQSE-2DAL-D DALI® Power Module
50017652a
EEA contact address:
Lutron EA Limited
125 Finsbury Pavement, 4th floor
London EC2A 1NQ
United Kingdom (Importer)
C
A
L
I
B
R
A
T
I
O
N
P
O
I
N
T
www.lutron.com/ChinaRohs
50
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
interference. (2) This device must accept any interference, including
interference that may cause undesired operation.
CAN ICES-3 (B)/NMB-3(B)
1
369650g 1 01.19.22
DALI® Power Module
(for regions outside of North America)
The DALI® Power Module is a DIN-rail mounted controller for
DALI®-compliant digital addressable loads, referred to as
control gear. It provides DALI® bus power and control for two
independent DALI® buses with up to 64DALI-compliant
digital addressable loads each.
Model Number
LQSE-2DAL-D: 2-link DALI® fixture controller
Features
• Provides power for two buses of DALI®-compliant digital
addressable loads:
– 128 mA guaranteed current
– 250 mA maximum supply current per bus
• Each DALI® bus can control a maximum of 16zones.
• Power failure memory retains programming in
the event of a power loss.
• DALI® Power Module can be used in a HomeWorkssystem to
control and manage light in an entire home or building.
DALI® Compatibility
The Lutron DALI
® Power Module is DALI-2® certified by the Digital Illumination Interface Alliance (DiiA)®. In order to ensure compatibility
with Lutron DALI® controllers, the connected DALI® LED drivers and fluorescent ballasts must be DALI-2® certified and marked. In
addition to compatibility, it is important to select high-quality and high-performance LED drivers and fluorescent ballasts. DALI-2®
certified devices are readily available from many manufacturers and are tested for compatibility with the standard. For a complete list of
available DALI-2® certified devices, see the DiiA® website at https://www.digitalilluminationinterface.org/products. DALI® devices that are
not listed on the DiiA® website and are not marked DALI-2® cannot be considered DALI-2® certified.
Assembled in Mexico
Assemblé aux Mexique
Ensamblado en México
L N
Ta > 65 ºC
Test | Prueba
Tester
HomeWorks QS
LQSE-2DAL-D
120 V~ 50 / 60 Hz 120 mA
230 V~ 50
/
60 Hz 80 mA
lutron.com
Ta ≤ 65 °C 65/75 ºC
MUX
MUX
NEC® Class 2
IEC PELV
COM
243C IND.CONT.EQ.243C IND.CONT.EQ.
Al
Cu
5 in-lb (0,6 N•m)
DALI® Power Module (LQSE-2DAL-D)
DA 1 DA 2
+1.844.LUTRON1
+44.(0)20.7702.0657
5/16 in
(8 mm)
NEC®
Class 2
The DALI® version-1 standard does not ensure compatibility. To apply the original DALI® version-1 mark on LED drivers and fluorescent
ballasts, no verification of the test results was required, and manufacturers could self-declare compliance and apply the DAL® mark. If
you would like to use an LED driver or fluorescent ballast that is not DALI-2® certified but carries a DALI® version-1 logo, Lutron
recommends that these devices be tested to ensure compatibility. Lutron is able to perform this testing on request. Samples of the
drivers and light engines must be submitted to Lutron and the expected turnaround time is 6 to 8 weeks after the drivers are received.
Fees for testing may apply. Lutron recommends that this testing be performed before the fixtures and lighting controls are purchased
and installed. Contact your Lutron sales representative for more information.
DALI
® bus 1
Up to 64
DALI®-
DALI
® bus 2
Control gear
Control gear
compliant
addressable
loads on each
digital
bus
Control gear Control gear
Input
Hi Temp
Prog
Power
230 V~ 50 / 60 Hz 10 A
Power
Module
500 W Max 800 W Max 500 W Max 500 W Max
CCI
Zone 2Zone 1 Zone 3 Zone 4
Option
H
Def
Opt1
M
L
Opt2
Opt3
LQSE-4A-D
DIN Rail Power Module
www.lutron.com +44.(0)20.7702.0657
HomeWorks
Processor
QS Contact
Closure
GRAFIK
Eye QS
Up to 100
total QS
devices
120 / 230 V~
Control Power
Assembled in Mexico
Assemblé aux Mexique
Ensamblado en México
L N
Ta > 65 ºC
Test | Prueba
Tester
HomeWorks QS
LQSE-2DAL-D
120 V~ 50 / 60 Hz 120 mA
230 V~ 50
Ta ≤ 65 °C 65/75 ºC
/
60 Hz 80 mA
lutron.com
HomeWorks
Wallstation
DA 1 DA 2
+1.844.LUTRON1
+44.(0)20.7702.0657
5/16 in
(8 mm)
NEC®
Class 2
NEC® Class 2
IEC PELV
MUX
COM
MUX
243C IND.CONT.EQ.243C IND.CONT.EQ.
Al
Cu
5 in-lb (0,6 N•m)
QS Link
Interface
DALI®
Job Name:
Power Module
SPECIFICATION SUBMITTAL Page
Model Numbers:
7
Sivoia QS
Shade / Drapery
QS
Power
Supply
Job Number:
Page 2
®
HomeWorks LQSE-2DAL-D DALI® Power Module
2
369650g 2 01.19.22
Specifications
® Buses
Power
• 120 V~ 50 / 60 Hz 120 mA
• 230 V~ 50 / 60 Hz 80 mA
• Lightning strike protection meets ANSI / IEEE standard
62.31-1980. Can withstand voltage surges of up to
6000 V~ and current surges of up to 3000 A.
• Stand by power: 7 W
• BTUs / hour when fully loaded: 24
• DALI
® bus Output: 16V- 128 mA guaranteed supply
current, 250 mA maximum supply current per bus.
Standards
• Lutron Quality Systems registered to ISO 9001:2015.
• IEC 60669-2-1
• DALI-2
® Certified
• UL
• cUL
• NOM
Environment
• Surrounding Air Temperature Range: 0 ºC to 65 ºC
(32 ºF to 149 ºF).
• Relative Humidity: less than 90% non-condensing.
• Calibration point maximum: 75 ºC (167 ºF)
• For indoor use only.
Terminals
• Mains Wiring: 1.0 mm
2
to 4.0mm2
(18AWG to 10AWG)
• DALI
® bus Wiring: 0.5 mm
2
to 4.0mm2
(20AWG to 10AWG)
• QS Link Wiring: 0.5 mm
2
to 4.0mm
2
(20 AWG to 10 AWG)
• Minimum wire temperature rating = 65 °C (149 ºF),
copper wire only
Mounting
• Mount in a Lutron DIN Panel (see spec 369788) or in
an IP20 (minimum) rated consumer panel or breaker
panel with integrated DIN rail.
• Width = 9 DIN modules (161.7 mm or 6
3
⁄8 in).
• For more information on mounting and installation in
panels with integrated DIN rail see Lutron P/N 048466
at www.lutron.com
Programming and Compatibility Requirements
• The LQSE-2DAL-D can only be used with a
HomeWorkssystem.
• Setup and programming of the DALI
® Power Module is
done through the Lutron Designer software.
DALI
• Up to 64 DALI
® compliant loads on each bus can be
addressed and grouped into 16 zones.
• DALI
® Power Module supplies a maximum of 250 mA
to power each bus.
• DALI
® Power Module supplies a guaranteed current
of 128 mA to power each bus.
• DALI
® Power Module has an integrated bus power
supply with polarity indicated on the unit.
• Some DALI
® loads may be polarity sensitive. Refer
to individual manufacturers' specifications for proper
connection to the DALI® bus.
• Short circuit protection with automatic restart.
QS Link Limits
• A QS link in a HomeWorkssystem can have up
to 512 zones (outputs) and 100devices. A DALI
®
compliant digital addressable load counts as 1 zone
unless specifically grouped into zones from the Lutron
Designer software.
• Each DALI
® Power Module counts as one device
toward the 100 device limit.
• A maximum of 8 fully loaded DALI
® buses may be
connected to a single QS link.
HomeWorks Wallstations
• HomeWorks wallstations can be configured to control
DALI
® Power Modules with the Lutron Designer
software.
• LED indicator displays the status of programmed lights.
Troubleshooting and Maintenance
Features
• Maintains redundant memory of control gear
programming for ease of single or multiple control
gear replacement.
• To verify DALI
bus 2:
– Enter Test Mode: Press and hold Test button on
the DALI
flashing.
– Test: Each press of either the DALI
DALI-2® button will cycle the lights between
high-end, low-end, flash and off for that bus.
– Exit Test Mode: Press and hold Test button until
Test LED stops flashing.
® lights connected to DALI® bus 1 and
® Power Module until the Test LED starts
® version-1 or
SPECIFICATION SUBMITTAL Page
Job Name:
Model Numbers:
Job Number:
Page 3
®
HomeWorks LQSE-2DAL-D DALI® Power Module
500-13431 Rev. B
N1771
Z096
3
369650g 3 01.19.22
Overview of Wiring Terminals and Mechanical Dimensions
IEC PELV / NEC®
Class 2
NECR Class 2
Assembled in Mexico
Assemblé aux Mexique
Ensamblado en México
L N
Mains
Wiring
Ta > 65 ºC
Test | Prueba
Tester
QS
Link
MUX
MUX
HomeWorks QS
LQSE-2DAL-D
120 V~ 50 / 60 Hz 120 mA
230 V~ 50
Ta ≤ 65 °C 65/75 ºC
/
60 Hz 80 mA
lutron.com
NEC® Class 2
IEC PELV
COM
243C IND.CO NT.EQ.243C IND. CONT.EQ.
Al
Cu
161.7 mm
(6 3⁄8 in)
5 in-lb (0,6 N•m)
DALI
®
bus 1*
DA 1 DA 2
+1.844.LUTRON1
+44.(0)20.7702.0657
5/16 in
(8 mm)
DALI®
bus 2*
NEC®
Class 2
89.7 mm
(3 1⁄2 in)
* Wire according to local codes.
SPECIFICATION SUBMITTAL Page
Job Name:
Model Numbers:
60.6 mm
(2 3⁄8 in)
Job Number:
Page 4
®
HomeWorks LQSE-2DAL-D DALI® Power Module
DA 1 DA 2
NEC®
Class 2
NEC® Class 2
IEC PELV
Ta ≤ 65 °C 65/75 ºC
Cu
Al
Assembled in Mexico
Assemblé aux Mexique
Ensamblado en México
Test | Prueba
Tester
Ta > 65 ºC
5 in-lb (0,6 N•m)
L N
MUX
COM
MUX
243C IND. CONT.EQ.243C IN D.CONT.EQ.
+44.(0)20.7702.0657
+1.844.LUTRON1
LQSE-2DAL-D
120 V~ 50 / 60 Hz 120 mA
230 V~ 50
/
60 Hz 80 mA
lutron.com
HomeWorks QS
(8 mm)
5/16 in
4
369650g 4 01.19.22
Wiring: Mains Voltage
Wiring from Distribution to Power Module
• Turn off all circuit breakers or isolators feeding the
Assembled in Mexico
Assemblé aux Mexique
Ensamblado en México
L N
Ta > 65 ºC
Test | Prueba
Tester
MUX
HomeWorks QS
LQSE-2DAL-D
120 V~ 50 / 60 Hz 120 mA
230 V~ 50
/
60 Hz 80 mA
lutron.com
Ta ≤ 65 °C 65/75 ºC
DA 1 DA 2
+1.844.LUTRON1
+44.(0)20.7702.0657
(8 mm)
NEC®
Class 2
NEC® Class 2
IEC PELV
MUX
COM
243C IND.CONT.EQ.243C IND.CONT.EQ.
Al
Cu
5 in-lb (0,6 N•m)
5/16 in
Power Module unit at the distribution panel.
• Run line, neutral, and earth / ground (D) wires from a
feed to the DALI
• Use 1.0 mm
® Power Module.
2
to 4.0 mm2 (18 AWG to 12AWG)
conductors (depending on breaker rating) to feed the
mains wiring. The device draws less than 120 mA
(120 V ~) and 80 mA (230 V~).
Emergency Lighting Applications
• Use normal (non-essential) power only to power the
® Power Module.
DALI
• When normal power drops out, the DALI
Module will not power the DALI
® buses. When this
® Power
occurs, control gear powered from emergency feeds
go to their emergency mode (full light output by default).
N
L
– Earth / Ground
– Neutral
N
– Mains / Line
L
Distribution
Panel
Mains Wiring and IEC PELV / NEC
® Class 2
Separation
• The DALI
mains wiring from IEC PELV / NEC
® Power Module is designed to separate
® Class 2 circuits.
• Follow appropriate local and national codes to avoid
violating required separation guidelines.
Job Name:
Job Number:
SPECIFICATION SUBMITTAL Page
Model Numbers:
Page 5
®
HomeWorks LQSE-2DAL-D DALI® Power Module
5
369650g 5 01.19.22
Wiring: DALI Bus
The DALI® Power Module will supply power for two
® buses, which supports a
®-compliant digital addressable
® Power Module and the end of the
Maximum DALI®-compliant
Bus Wire Length
Assembled in Mexico
Assemblé aux Mexique
Ensamblado en México
Ta > 65 ºC
Test | Prueba
Tester
L N
®
DALI
bus 1
DALI® 1
DALI
® 1
HomeWorks QS
LQSE-2DAL-D
120 V~ 50 / 60 Hz 120 mA
230 V~ 50
Ta ≤ 65 °C 65/75 ºC
/
60 Hz 80 mA
lutron.com
independent DALI
maximum of 64 DALI
DA 1 DA 2
+1.844.LUTRON1
+44.(0)20.7702.0657
(8 mm)
NEC®
Class 2
loads per bus.
DALI
• DALI
• DALI
® Wiring
® wiring is not SELV.
® wiring may be treated as mains voltage, and
NEC® Class 2
IEC PELV
MUX
COM
MUX
243C IND.CONT.EQ.243C IND.CONT.EQ.
Al
Cu
5 in-lb (0,6 N•m)
5/16 in
thus can be run within the same sheathing.
• Ensure that there is no greater than a 2 V~ drop
DALI
bus 2
DALI
DALI
®
® 2
® 2
between the DALI
® bus.
DALI
• Consult all national and local electrical codes for
separation requirements.
Wire Gauge
2
1.5 mm
(14AWG) 300 m (984 ft)
0.75 mm
0.5 mm
2
(18AWG) 150 m (492 ft)
2
(20AWG) 100 m (328 ft)
SPECIFICATION SUBMITTAL Page
Job Name:
Model Numbers:
Job Number:
Page 6
®
HomeWorks LQSE-2DAL-D DALI® Power Module
6
369650g 6 01.19.22
Wiring: QS Link
IEC PELV / NEC® Class 2 QS Link Wiring
®
2
(20 AWG)
Assembled in Mexico
Assemblé aux Mexique
Ensamblado en México
L N
Ta > 65 ºC
Test | Prueba
Tester
HomeWorks QS
LQSE-2DAL-D
120 V~ 50 / 60 Hz 120 mA
230 V~ 50
Ta ≤ 65 °C 65/75 ºC
/
60 Hz 80 mA
lutron.com
• Link communicates using IEC PELV / NEC
DA 1 DA 2
+1.844.LUTRON1
+44.(0)20.7702.0657
(8 mm)
NEC®
Class 2
NEC® Class 2
IEC PELV
MUX
COM
MUX
243C IND.CONT.EQ.243C IND.CONT.EQ.
Al
Cu
5 in-lb (0,6 N•m)
5/16 in
Class 2 wiring.
• Follow all applicable national and local codes for
proper circuit separation and protection.
• Wiring may be daisy chained or t-tapped.
• Do NOT connect terminal 2.
• Total length of QS link must not exceed 610 m
(2000 ft).
• Use one, twisted-shielded pair of 0.5 mm
for data link (MUX, _).
(1)
COM
(2)
No Connection
(3)
MUX
(4)
MUX
QS Link
Wiring Length Wire Gauge
Power (terminals 1 and 2):
Less than
153m (500 ft)
1 pair 1.0mm
Data (terminals 3 and 4):
1 pair 0.5mm
twisted and shielded
Power (terminals 1 and 2):
153m to
610m
(500 to 2000 ft)
1 pair 4.0mm
Data (terminals 3 and 4):
1 pair 0.5mm
twisted and shielded
2
(18 AWG)
2
(20 AWG),
2
(10 AWG)
2
(20 AWG),
Available from
Lutron in one cable:
GRX-CBL-346S
(non plenum)
GRX-PCBL-346S
(plenum)
GRX-CBL-46L
(non plenum)
GRX-PCBL-46L
(plenum)
The Lutron Logo, Lutron, HomeWorks, Sivoia, and GRAFIK Eye are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the US and/or other countries.
All other product names, logos, and brands are property of their respective owners.
SPECIFICATION SUBMITTAL Page
Job Name:
Model Numbers:
Job Number:
Loading...