Lowrance MAPCREATE 7 User Manual

™

www.lei-extras.com

Pub. 988-0154-942

MapCreate 7

Custom Mapping Software for GPS

Installation and Operation

Instructions

No part of this manual may be copied, reproduced, republished, transmitted, distributed, downloaded or stored in any storage medium, for any purpose, without prior written consent of LEI. Any

unauthorized commercial distribution of this manual is strictly prohibited.

MapCreate™ is a trademark of LEI.

LEI Extras, Lowrance Electronics, or Eagle Electronics may find it necessary to change or end their policies, regulations and special offers at any time. They reserve the right to do so without notice. All screens in this manual are simulated.

For free owner's manuals and the most current information on this product, it's operation and accessories, visit the manufacturer's web sites:

www.lowrance.com www.eaglegps.com

To purchase Lowrance or Eagle accessories,

visit our web site:

www.lei-extras.com

LEI

PO BOX 129

Catoosa, OK USA 74015

Printed in USA.

Table of Contents

Section 1: Introduction............................................................. 1

Quick Start Reference.................................................................... 3

How MapCreate Works: the Basics ............................................. 6

File Formats & Functions............................................................. 7

Map Border File ........................................................................ 7

Custom Map File ....................................................................... 8

Important Notes: File Encryption and Card Limits ............... 8

Map File Encryption ............................................................. 8

Limited Number of Cards ..................................................... 8

Important Notes about Cards and File Size............................ 9

GPS Data File.......................................................................... 11

ASCII Text File........................................................................ 11

GPS Data Manger (GDM) File ............................................... 12

Atlas File.................................................................................. 12

GPS Unit Compatibility.......................................................... 13

Mapping Detail: There's more here than meets the eye. ............ 13

Find Highway Exit Services ................................................... 13

Find Points of Interest ............................................................ 14

Find an Address ...................................................................... 14

How to use this manual: typographical conventions ................ 15

Mouse ....................................................................................... 15

Keyboard .................................................................................. 15

Instructions.............................................................................. 16

MapCreate 7 ................................................................................ 16

Material covered includes:...................................................... 17

New Mapping Data ............................................................. 17

Additional Symbols ............................................................. 17

Searching ............................................................................. 17

Aviation Searching .............................................................. 17

Find Nearest Waypoint or Nearest Highway Exit............ 17

Map Category Options Toolbar .......................................... 17

Routing................................................................................. 17

Dynamic Pan Arrows .......................................................... 17

Pop-up Boxes ....................................................................... 17

Color Legend........................................................................ 17

Map Coverage by DVD................................................................ 18

New Mapping Data Types: ......................................................... 18

Elevation Contour Lines ......................................................... 18

Hunting .................................................................................... 18

Other Data Types .................................................................... 18

Hunting Specific Symbols........................................................... 19

Searching ..................................................................................... 19

Aviation Searching...................................................................... 21

Find Nearest Waypoint, Highway Exit ..................................... 21

Map Category Options Toolbar .................................................. 21

Routing..................................................................................... 22

Dynamic Pan Arrows .................................................................. 22

Pop-up Boxes ............................................................................... 22

Color Legend................................................................................ 23

Section 2: Installing MapCreate 7 ....................................... 25

System Requirements: ............................................................ 25

IMPORTANT NOTES:............................................................ 25

Installation Types ................................................................... 26

Installing MapCreate.............................................................. 26

Care of your MapCreate DVD ................................................ 36

Starting MapCreate ................................................................ 36

Section 3: User's Guide ........................................................... 39

Working With MapCreate....................................................... 39

Starting MapCreate .................................................................... 39

The MapCreate Screen ............................................................... 39

Closing MapCreate.................................................................. 41

MapCreate Screen Components ............................................. 41

Master Map Window ............................................................... 41

Main Menu............................................................................... 43

Toolbars.................................................................................... 43

Create Map (Easy) toolbar.................................................. 44

Create Map (Advanced) toolbar.......................................... 44

Map Category Options Window.............................................. 48

Waypoint List Window............................................................ 49

Icon List Window..................................................................... 49

Route List Window .................................................................. 49

Route Waypoint List Window................................................. 50

Trail List Window ................................................................... 51

Moving Around the Master Map ................................................ 52

Pan Arrows .............................................................................. 52

Center Map .............................................................................. 52

Zoom Area ................................................................................ 52

Zoom In/Zoom Out................................................................... 53

Zoom Range Window............................................................... 54

Creating Rectangle Map Borders............................................... 54

Estimate Map Size (Optional) ................................................ 55

Saving a Map Border File (Optional)..................................... 56

Creating Corridor Map Borders ................................................. 57

Edit Corridor Borders ............................................................. 59

Creating and Saving a Custom Map.......................................... 60

Creating a Waypoint ................................................................... 62

Creating an Icon.......................................................................... 64

Creating a Route ......................................................................... 66

Saving a GPS Data File .............................................................. 69

Moving GPS Data Files between Computer and Unit.......... 70

Creating a Corridor Map from a Route...................................... 71

Creating a Route from a Trail .................................................... 73

Appendix 1: MapCreate Command List ............................. 77

Searching Help ............................................................................ 79

Internet Explorer browser: ..................................................... 79

Netscape 6 browser: ................................................................ 80

Appendix 2: Map Category List ............................................ 81

Appendix 3: MapCreate 7 Symbol Key ............................... 85

Appendix 4: Considerations When Planning Highway

Routes ......................................................................................... 89

Tips on Making Better Routes for Highway Navigation ...... 89

"High Resolution" vs. "Low Resolution" Routes .................... 89

Index ........................................................................................... 93

iii

WARNING!

A CAREFUL NAVIGATOR NEVER RELIES ON ONLY ONE METHOD TO OBTAIN POSITION INFORMATION.

When showing navigation data to a position (waypoint), a GPS unit will show the shortest, most direct path to the waypoint. It provides navigation data to the waypoint regardless of obstructions. Therefore, the prudent navigator will not only take advantage of all available navigation tools when traveling to a waypoint, but will also visually check to make sure a clear, safe path to the waypoint is always available.

When a GPS unit is used in a vehicle, the vehicle operator is solely responsible for operating the vehicle in a safe manner. Vehicle operators must maintain full surveillance of all pertinent driving, boating or flying conditions at all times. An accident or collision resulting in damage to property, personal injury or death could occur if the operator of a GPSequipped vehicle fails to pay full attention to travel conditions and vehicle operation while the vehicle is in motion.

CAUTION

WARNING!

Section 1: Introduction

How this manual can get you into the field, fast!

Thanks for buying MapCreate™, the custom mapping software for Lowrance and Eagle GPS units. This manual was written using MapCreate™ version 7. Beginning with version 7, all MapCreate packages work identically, but contain different mapping data.

We know you're eager to install the program and make some maps, but we have a favor to ask. Before you grab that DVD, give us a moment to explain how our manual can help you get the best performance from our software. Our goal is to get you on the road, into the air, or out to the woods and water fast. Like you, we'd rather spend more time outdoors, and less time reading a manual!

That's why we designed this book so you don't have to read the whole thing from front to back for the information you want. You can skip around! If you know where to look, we've made it easy to find the tips you may need from time to time.

The manual has three main sections:

Section 1: Introduction contains the Quick Start Reference, which begins on page 3. We put it near the front of the book so you can turn to it quickly. Sec. 1 also includes background information on how MapCreate and its file formats work. To understand how to interpret our instruction text, be sure to see the Typographical Conventions segment on page 15. Don't miss the important notes on File Encryption and Card Limits on page 8.

Section 2: Installing MapCreate (on page 25) will help you get the program and the required LEI card reader correctly installed on your computer.

Section 3: User's Guide (on page 39) is the heart of our book. It introduces you to the MapCreate windows and toolbars. Sec. 3 contains easy-to-skim lessons on the program's main operations. These segments show you how to make highly customized maps and GPS information and get them into your GPS unit.

After you've gained some experience with the program, you may want to try some advanced features. That brings us to the Command Reference, which is available only in the MapCreate 7 Help file. It contains — in alphabetical order — the more advanced command functions in MapCreate.

Each entry includes a summary box briefly telling what the command does and how to run it from the menu, toolbar or keyboard. Then, we've included more tips and tricks so you can take advantage of all the power and performance MapCreate offers.

You can see an example of the Help file's Command Reference format in Appendix 1 at the back of this manual, on page 77. Appendix 1 contains the entry on the Help Command, which explains how to use Help.

In addition to the Command Reference, the Help file includes material from this manual's User's Guide segment. Just press the F1 key to launch Help. You can find facts fast by electronically searching the Help File for the word or phrase you want.

In our printed manual, we've included other general supplemental material as appendices in the back of the book. Check out the Table of Contents to see the topics contained in each appendix.

After you have the software and card reader installed, browse through the tutorials in Sec. 3 to get you going. Later, when you want to try something new or you have a question about a particular function, skim through the manual's table of contents or search the Help file's Command Reference to read what you need.

If you're an experienced computer user, you can probably install MapCreate and the card reader without the manual. But, if you need a little coaching, jump ahead to Sec. 2 and we'll walk you through the install step by step. (If that's not easy enough, just grab the nearest teenager and ask him or her to install it for you!)

If you've skipped ahead and already have MapCreate installed, check out the Quick Start Reference below. If you're the type of person who wants more background information before you start, turn to How Map Create Works on page 6, or begin learning about the MapCreate screen components at the start of Sec. 3.

Quick Start Reference

This 13-step summary will get you started with a simple map. It assumes you have already made a full, default installation of the program, and one of the CDs is in your CD-ROM drive. (Complete installation instructions begin in Sec. 2.) For more detailed explanations, read through the lessons in Sec. 3. Before you start, make sure your LEI MMC card reader is installed and working and you know the reader's drive letter. Many

toolbar buttons are labeled and an informative tool tip box pops up when you point to a button.

How to make and save a rectangle map

1. Start MapCreate by clicking the Windows

your version of

MAPCREATE from the menu.

2. Maneuver the Master Map so you can see the area you want to include in your map. Use the east or west. Use the

PAN ARROW buttons to move north, south,

ZOOM-IN and ZOOM-OUT (Z-IN or Z-OUT) buttons as

needed to close in on or back away from the area you're viewing.

3. Click the

DRAW MAP BORDERS button in the toolbar. Move the mouse

pointer above and to the left of the desired area. Click, hold down the mouse button and drag diagonally down and to the right until the desired area is enclosed with the green border box. Then release the mouse button. You have just drawn a Map Border.

4. With the Map Border displayed, click the ton, on the Create Map toolbar. After a moment it will tell you your map's file size. If it fits the card, click

OK to clear the message and jump to step 5.

If the map file is too large for the card, click redraw your map border a little smaller. Click the ton, click on any green border line, then re-draw a smaller border box. Use the Estimate button to re-check the size until it is correct.

START button and choosing

ESTIMATE CUSTOM MAP SIZE but-

OK to clear the message, then

DELETE MAP BORDER but-

Click the OK button to clear the message box from your screen.

5. When your file is the right size, click the CREATE MAP button on the

Create Map toolbar. The program displays a message about copyright and encryption.

6. If this is the first time you have tried to save a file to your memory card, MapCreate will need to register the card. Make sure you have a card in your card reader. Click

OK to continue. (Clicking Cancel ends

the process.) If you have already registered the card you are using, click

OK and skip to step 11.

Read the message, and then click OK to continue.

7. Another message box asks whether you want to register your current

card or not. Click

YES to continue the card registration process.

Click Yes to register your current memory card with MapCreate.

8. You can change the label on your memory card if you prefer. Delete

the default name, "Card1," and enter the new name. Click

continue.

Delete the default label, if you prefer, and enter a new name. Then

click Register to continue.

9. Another message box tells you when your card has been registered. Click

OK to continue.

Click OK to continue the create map process.

10. The Card Registry window appears again. Click DONE to save your map.

Click Done to complete the registry process.

NOTE:

If the

AUTOMATICALLY APPEND LABE L TO SAVED MAPS box is selected (see

figure above), MapCreate will automatically add your card's label to the end of whatever name you give the file you are saving. Let's use the figure above as an example. If we name our map "Phoe-

nix.lcm," MapCreate will automatically name the file "Phoenix_CARD1.lcm." To cancel this option, click the Automatically Ap-

pend… box to remove the check mark.

11. A window shows the progress of your map build. When the map is built, MapCreate displays the your Map File, and click

SAVE AS dialog box. Type a file name for

SAVE. (MapCreate will save your new custom

map to your memory card.)

12. After the program has saved the map to your card, the Save Progress box disappears. You can now close MapCreate and remove the card from the reader.

13. Follow the instructions in your GPS manual for loading the MMC or SD card into your unit. It will automatically read the map when the unit is turned on.

NOTE:

Custom maps and GPS data (waypoints, routes, trails, icons) are contained in two different file types. We describe their functions in the following segments on how the program works.

How MapCreate Works: the Basics

You'll be making maps faster if you understand the hoops MapCreate must jump through to cram a high-detail map into your GPS unit.

First of all, those CDs you just purchased contain a whole bunch of raw digital cartography data. There are several hundred files of digital mapping information containing lake shorelines, navigation aids, roads, rivers and all the other information that goes into our high-detail maps.

It takes some fancy formatting to fit the whole world onto a few compact discs. Your GPS unit can't read those raw files (called atlas files). Even if it could, no GPS unit or MultiMedia Card (MMC) has enough memory to hold that much information.

This is where MapCreate comes in. The program looks at all those raw atlas files, shuffles the different types of information together, and then places them onto your computer screen. That's what we call the Master Map, the main window in the MapCreate interface. By changing various options in MapCreate, you can control how much geographic detail is displayed on-screen in the Master Map.

It's a pretty cool electronic map, but your GPS can't read it in this form, either. This is where you come in. You move around the Master Map and locate the area or areas you want to make a detailed map of. Then, you use the computer mouse to draw a map border around the region you want.

Now, this map border isn't really a map yet — it just defines or outlines the area you want to include in the final GPS-friendly map. If you wish, you can save the boundary you have drawn as a Map Border File. MapCreate uses a map border like an electronic shopping list. The program looks at your border, grabs the appropriate raw atlas information, and then glues it all together as a custom map. Now you can save this data as a Custom Map File on an MMC (or SD card) and load it into your GPS unit. (If you like, you can backup the Map File by copying it from the MMC card to your computer's hard drive.)

GPS information — such as waypoints, routes or trails — is handled differently. You can click the mouse to set a waypoint or plan a route, then save that information as a GPS Data File. Just save it directly on or copy it to the MMC and this file is ready to load into your GPS unit. When your unit makes trails or waypoints in the field, that information is also saved as a GPS Data File. Your GPS unit can save the file to the MMC, which allows you to copy the GPS Data File back into your computer. Then you can open, edit and save it in MapCreate.

File Formats & Functions

Well, now you know what makes MapCreate tick. You may be ready to skip forward to where we explain how our text formatting makes the manual easy to skim. If that's the case, move on to "How to Use This Manual: Typographical Conventions" on page 15. But, if you want to pick up an extra tip or two, look over this segment describing the file formats and memory cards MapCreate works with.

Map Border File

This file defines the boundary of the raw cartography data that is extracted and converted to a GPS custom map, or Map File. The border file information is displayed on the computer's Master Map screen as either a green rectangle (rectangle map border) or a magenta polygon shape (corridor map border). The file extension is *.lmp.

In MapCreate 7, you can draw a border, then build and save a map without saving the border. However, some MapCreate power users still

like to save their borders as Map Border Files. That lets them make changes to a border or even combine different borders without drawing them from scratch each time. By default, MapCreate will first save a Map Border File to the C:\Program Files\LEI\MapCreate\Data folder, but if you prefer you can save it on your memory card. If you save elsewhere, MapCreate remembers that location the next time you save. Version 7 also stores map border information in each Map File. This lets you generate a border simply by opening an existing Map File, including maps built by previous versions of MapCreate.

A Map Border File can contain one or more different map border sets, and these border sets don't need to be next to each other on the map. For example, you can draw a rectangle border around one lake and then draw a second corridor border around another lake several miles away, and include both of those border sets into one Map Border File. There is no limit (other than space on your hard disk, MMC or SD card) on how many different border sets you can include in a Map Border File. You can open and edit a Map Border File and then save the file with the changes you made.

Custom Map File

This is the actual map format used by your GPS unit. MapCreate takes the borders you drew (or saved as a Map Border File), extracts that area's information from the raw atlas data, then converts it to a Custom Map File, often called a Map File for short. We call this conversion process "creating the map." The file extension is *.lcm.

By default, MapCreate will first save a Map File direct to your MMC memory card. If you prefer, you can save a Map File on your computer hard drive. When hard drive space is available, many users like to archive Map Files in the C:\Program Files\LEI\MapCreate\Data folder. This allows you to change maps on your card and reuse a map over and over without creating it each time. If you save a map to the Data folder, MapCreate will remember that location the next time you save a map, during the current work session. The next time you start MapCreate, map saves will default back to the MMC card.

You cannot make changes to a Map File once it has been created. If you want to make changes to a map, return to its original companion Map Border File or retrieve the map borders by opening the Map File (*.lcm). Make your changes to the border, then create a fresh Map File. You can delete the old one, or just save the new map over the old map.

Important Notes: File Encryption and Card Limits

We collect and purchase cartography data from several sources. Much of this data is copyrighted, and our data suppliers require that we protect our maps from illegal copying. One level of protection requires that you have the MapCreate DVD in the disc drive each time you launch the program. We also encrypt Map Files, and limit the number of MMC or SD cards you can use to store maps.

Map File Encryption

All maps built by MapCreate are required to be encrypted (or locked) to a specific memory card. This encryption process must be done on maps saved both to a memory card and your hard drive. Once a map has been encrypted to a specific memory card, you can make a backup copy on your hard drive, but you cannot copy the map to a different card. (Well, you can copy it to another card, but your GPS unit won't recognize it. To work, the Map File must reside on the card it was encrypted to.)

Limited Number of Cards

All MapCreate users are limited to saving maps on a maximum of five different memory cards. MapCreate tracks the number and identity of your cards by "registering" each card with the program. The software needed to register cards will not work with third-party card readers, so MapCreate will only work with the card reader from LEI. Once you have registered a card, it can never be unregistered and its place exchanged with another card.

Since you are limited to five, we strongly recommend that before you buy more cards, you should give some thought to the type of travel you do and your map size requirements. Memory cards come in several different sizes, so you need to think ahead and match card capacity to the type of maps you will need.

To help you decide what size cards to buy, make some map borders covering the type of travel you expect. Then use the Estimate Custom Map Size command to calculate the size.

For example, one Missouri customer frequently travels and fishes in the four-state area of Kansas, Missouri, Arkansas and Oklahoma. He purchased an additional 128MB MMC, which holds all four states at once. This lets him travel long distances for extended periods without needing a computer to change the maps on his card.

To give you an idea of how big a Map File can be, we made some examples using the regular versions (no topographic data) of MapCreate USA and MapCreate Canada, with all mapping categories included. (Size will vary depending on which package of MapCreate you have.)

In the U.S., Lake Michigan is approximately 26 MB, all of Missouri is 41 MB and the entire state of California is approximately 87 MB. A six-milewide corridor map from San Diego, California to the Maine-Canada border, following Interstate highways, is about 50 MB.

In Canada, a map of Lake Winnipeg (including the major lakes to the northwest) is 6.84 MB. All of Saskatchewan is 64 MB; all of British Columbia is 69 MB. A six-mile-wide corridor map from Prince Rupert on the west coast to Louisbourg on the east coast, following Trans-Canada highways, is about 35 MB.

Important Notes about Cards and File Size

The size of a Map File is important. It must be small enough to fit on the MMC (MultiMedia Card) that your GPS uses for data storage. This solid-state, flash memory device is about the size of a postage stamp. (SD [Secure Digital] cards are also compatible with any Lowrance or Eagle product that uses MMCs.)

At press time, the MMCs shipped with the GPS Accessories Pack version of MapCreate 7 are 32 MB size. If you're using a 32 MB MMC, your Map File must be less than 32 MB in order to fit on the card. (This space issue is the same as floppy disks; you can't really fit a 1.44 MB file onto a 1.44 MB diskette because some space is required for the disk's file allocation table. In the case of a 32 MB MMC, actual maximum useable space will be approximately 29 MB to 30 MB.)

MMCs and SD cards are used in a variety of other digital devices. Most electronics or digital camera stores sell MMCs and SD cards, and at press time they are available in 16 MB, 32 MB, 64 MB, 128 MB, 256 MB and 512 MB sizes. Cards with even greater capacity will likely be available in the future. MapCreate is a powerful tool for your GPS, because it allows you to match your map's file size and detail level to your card's memory capacity and your travel needs.

NOTE:

Due to software requirements in the GPS units, MMC or SD cards can hold a maximum of 32 different files at one time for the Lowrance iFINDER

and 1,000 different files for all other Lowrance or Eagle GPS receivers. The total amount of information cannot exceed the MMC size capacity, no matter what the number of files is. For example, an 8 MB MMC in an iFINDER could hold approximately one 7.66 MB file, or 32 files, so long as the 32 files totaled 7.66 MB or less.

Other brands of GPS units use direct serial cable connections to transfer high detail maps from a computer to the GPS device. Lowrance and Eagle switched from this traditional method to removable memory cards for several reasons. A USB card reader can transfer a large custom map to your unit 30 times faster than a serial cable connection. Removable media means you don't have to take a computer and cable with you to load a new map in the field. If the unit is mounted in a vehicle, there is no need to dismount it and carry it to a computer. The effective mapping memory capacity of your GPS unit is restricted only by the capacity and number of memory cards you want to carry with you, up to the five-card limit. This is a handy feature for long journeys or for users who can't lug a laptop computer along.

Four factors control Map File size: 1. map detail level option settings,

2. the number of map feature categories turned on, 3. the amount of de-

veloped or naturally occurring features in the area and 4. the amount of territory, that is, the number of square miles or acres in the area.

Detail Level Options can be set to high or medium. The higher the level of detail, the bigger the file size will be.

There are dozens of Map Category Options that you can turn off and on. They include natural features — such as rivers — and man-made items such as roads, businesses or other points of interest. The more categories and subcategories turned on, the bigger the file size.

The amount of development in an area is something you can't control. For example, one square mile of city streets will make a larger file than one square mile of wilderness with a few hiking trails.

The amount of territory you include in a map is a major factor. The more square miles or acres you include, the bigger the file size.

The lessons in the manual were written using MapCreate's default settings, with high detail and all categories turned on. If your first maps don't fit your MMC or SD card, refer to the Help file's Command Reference section for more detailed instructions on controlling file size.

GPS Data File

This file format contains all the GPS navigation information (waypoints, event marker icons, routes and trails) used by your GPS unit and MapCreate. The file extension is *.usr (for User file). By default, MapCreate first saves a GPS Data File to the C:\Program Files\LEI\MapCreate\Data folder, but if you prefer you can save it direct to your MMC card. If you save elsewhere, MapCreate remembers that location the next time you save. Since GPS data files are not encrypted, it does not matter how you move .usr files around. As with other Windows-based files, you can freely drag and drop these files back and forth from the hard drive to any MMC.

You can open and make changes in a GPS Data File once it has been created. The contents can include any combination of waypoints, routes, trails and event marker icons. The information shows up graphically on the Master Map as symbols with names. The same information is also available as text in a list window, such as the Waypoint List window.

Your GPS unit saves field-collected GPS information in the same format so MapCreate can be used to save valuable travel or adventure data for a later trip. This also makes it easy to exchange GPS data with friends using Lowrance or Eagle GPS equipment.

ASCII Text File

This is a universal text file format compatible with word processors and other software. MapCreate can exchange routes and waypoint lists with other mapping programs by importing and exporting GPS information as comma-delimited ASCII text files. ASCII (pronounced "askee") uses the *.txt file extension. You don't need to work with these files, unless you plan to exchange routes and waypoints between MapCreate and other mapping programs. If you want to create a text file manually, or if you need to manually edit a route or waypoint text file, this is the waypoint position format MapCreate will export or import:

[latitude],[space][longitude],[space][waypoint name]

Each position is written in degree (decimal) format. For North latitudes, use the latitude with no preceding symbol. For South latitudes, a minus sign must precede the number, like this: –latitude.

For East longitudes, use the longitude with no preceding symbol. For West longitudes, a minus sign must precede the number, like this: –longitude.

The first waypoint in the following example text file is N 36.06079846º, W 95.78354912º.

First wpt

Last wpt

In routes, sequence is important. 1st line is wpt 1, 2nd line is wpt 2 and so on.

Latitude Longitude Waypoint Name

36.060798, -95.783549, Church 1

36.060784, -95.761647, Turn North 2

36.161831, -95.761529, Turn N-East On Hwy66 (3)

36.162581, -95.753760, Wpt 004*

36.169981, -95.751795, Wpt 005*

36.382616, -95.556565, Turn N-West 6

36.385315, -95.560847, Turn North 7

36.503465, -95.561081, Stop Turn East 8

Comma and space separate items.

Text files are saved in the C:\Program Files\LEI\MapCreate\Data folder. For more information on how to use text files, see the Help file Command Reference topics "Export GPS Data," "Import Route" and "Import Waypoint List."

GPS Data Manger (GDM) File

This is an older file format used by MapCreate 5 and MapCreate 4 to hold navigation data (waypoints and such). MapCreate 7 can open these files, making the program backward compatible with versions 5 and 4. The GDM file extension is *.low. Although MapCreate 7 is designed to load and read older GPS Data Files in the *.low format, MapCreate 7 will only save GPS Data Files in the newer *.usr format. Please note that your MapCreate 7-compatible GPS unit can only read *.usr files.

Atlas File

This is the "raw" file format for layer after layer of cartographic and hydrographic data on our CDs. You never have to work with these files directly. MapCreate pulls data from these files to display the Master Map you see in the main window on your computer. The program combines the information from a Map Border File with the Atlas Files to make Map Files for your GPS unit.

NOTE: MMC Card Formats

If you have an older MMC that has been formatted by a parallel port Lowrance MMC Interface card reader, the card format may not be compatible with your newer USB port MMC card reader. If that's the case, you can preserve your historic GPS data by copying it to your hard drive with your older parallel port reader. The older MMC can then be reformatted so it will work with the newer USB card reader. To reformat an MMC, refer to the instructions that came with your USB MMC card reader or your sonar/GPS unit.

If you ever have to format your MMC card, you should know that MapCreate, as well as Lowrance and Eagle GPS products, will only

read cards that are FAT formatted. MMC cards formatted using FAT 32 or NTFS will not work with these products.

WARNING:

You should never format an MMC containing a Navionics chart or Jeppesen

aviation database. Formatting the MMC will

permanently erase the chart or aeronautical data from the card.

GPS Unit Compatibility

MapCreate 7 is compatible with all Lowrance and Eagle mapping GPS units that use removable MMC/SD cards for map storage. Some units, however, may need a free software upgrade to work with MapCreate 7. Upgrades are available for download from the web sites, www.lowrance.com or www.eaglegps.com. Look for the MapCreate 7 section, which will contain a list of units that need upgrades. Follow the links to download your free software upgrade.

If you have questions, call customer service for your GPS unit. Contact information is on the last page of this manual.

Mapping Detail: There's more here than meets the eye.

The Map Files you make with MapCreate contain more mapping detail than what is visible on your computer screen. Your MapCreate7-compatible GPS unit takes full advantage of this extra information.

Find Highway Exit Services

For example, move your mouse pointer over a highway exit symbol on the computer map, and all you'll see is a pop-up tool-tip box listing the name of the exit. However, in a Lowrance or Eagle GPS unit, the same exit symbol will show a pop-up box with the exit name and symbols of all the services available near that exit. The GPS unit can also provide you a list of those services.

Cursor over exit symbol

Pop-up box

At left, an iFINDER GPS screen showing an exit services pop-up icon

box. The iFINDER can then display a text list of those services near

the selected exit, right.

Find Points of Interest

On the computer master map, moving your pointer over a Point of Interest (POI) symbol triggers a pop-up box with the POI's name. With MapCreate 7, when the information is available, the pop-up box also displays the POI's address and telephone number. This detailed pop-up only works for items classified as Points of Interest.

Map with pop-up box showing POI information

In a Lowrance or Eagle GPS, all POI's include the name, address and phone number.

Cursor over POI symbol

Pop-up box

At left, an iFINDER GPS screen showing a POI pop-up name box. At

right, you can call up a page of information on the POI, and the GPS

unit can lead you to the POI's location.

Find an Address

You won't see addresses on your computer map (except listed in the pop-ups for some POIs). But when the MapCreate information is loaded into your GPS, you can search for a street address or a street intersection. In fact, your GPS unit can search by name for virtually every category of mapping detail contained in MapCreate.

All of this information is built into MapCreate's atlas database. As long as an information category is turned on and included in your Map File, the data will be available to your GPS unit.

With these and other elements, MapCreate gives you a phenomenal amount of mapping detail and information. For a more detailed list of the map categories available in MapCreate, see Appendix 2, Map Cate- gory List, on page 81.

How to use this manual: typographical conventions

Most Windows-based computer programs offer several ways to perform a task, and MapCreate 7 is no exception. With mouse and keyboard, you can access some commands four different ways! We'll show you all of them, but we save the most detailed information for our Help file's Command Reference section. There, the entry on each command includes a summary box showing all the menus and keyboard shortcuts (sometimes that's the only hint you need to get on with your mapping project).

In our User's Guide segment (Sec. 3), we usually focus on one simple way to get the job done, usually by clicking the mouse pointer on a menu or toolbar button. In the User's Guide, many of the instructions are listed as numbered steps. This makes it a little easier to follow a series of instructions when you're skimming the material.

In the printed User's Guide and the Help file Command Reference, the actual command clicks and keystrokes appear as sans serif, boldface type. So, if you're in a hurry (or just need a reminder), you can skim the instructions and pick out where to click by finding the boldface commands. The paragraphs below explain how to interpret the text formatting for those commands and other instructions (If you're already familiar with Windows or many other software manuals you can probably skip forward to Section 2: Installation, on page 25.).

Mouse

The mouse controls the movement of a graphic symbol on your screen called the mouse pointer, sometimes also referred to as a mouse cursor. The mouse performs an action by moving the pointer over a menu, a button or the map and then clicking the appropriate mouse button.

When the word "click" is used alone, it means "left-click," or to press and release the left mouse button. When you need to use the right mouse button, we will say so explicitly, such as "Right-click on the waypoint."

Sometimes a command requires more than one click. When we say "double-click," it means to rapidly click the mouse button two times.

Keyboard

The keys on your keyboard may not be labeled exactly as they are in this manual. All key names are shown in bold, sans serif type. For example, the "Control" key is shown as

Ctrl and the "Enter" key is shown as Enter.

Keys are sometimes used in combinations. For example, to hold down the quence

Alt+T|W indicates a two-step combination: hold down the Alt key

while pressing the

Ctrl key while pressing the T key. The hot key se-

T key, release, then press the W key.

Ctrl+T means

"Arrow keys" is the collective name for the up arrow, down arrow, left arrow and right arrow keys.

To choose a command from a menu, you can use the mouse or press a key combination.

Instructions

Words in small capital letters, in a bold sans serif type, indicate that you are to take an action of some kind with a command, menu, box or other item. For example, "You can use the Create Route command to plan a path to navigate with your GPS. To begin the route, choose

CREATE ROUTE."

When the phrase "choose command" is used in the Help file Command Reference section, it means to run or execute the specified command. For example, if the manual says "choose

CREATE WAYPOINT," it means to

run the Create Waypoint command. You can choose commands by clicking the mouse pointer on the menus or toolbar buttons, or by pressing the appropriate hot key or shortcut key on the keyboard.

Commands are sometimes described as menu sequences, to help you find the command faster. For example, "to open the Trail List window, click

VIEW|TRAIL LIST," means to mouse click on the main menu's View

command and then click the Trail List command on the submenu.

Specific text or numbers you must type are shown in bold, sans serif type. For example, if the manual says "Enter a Zoom range of

650

miles," you would click in the Zoom Range Window, type the numbers 650, then press the

Enter key.

Place holders for other items you must supply yourself, such as file names, are italicized. For example, when the manual says "Enter a name in the File Name text box," you would click in the text box, type the name you want to use for the file, then press the

Enter key.

This manual is written specifically for MapCreate™ 7, but for simplicity, the program is often referred to as "MapCreate" or "MapCreate 7."

MapCreate 7

MapCreate 7 is ideal for aviation, backpacking and related outdoor activities, but it was specially designed for hunters. Maps made with MapCreate will work in all Lowrance mapping software to offer such extensive boundary data for several types of public hunting lands, game management units and related areas.

GPS units. MapCreate 7 is the first GPS

NOTE:

We strongly recommend you check the Lowrance web site, www.lowrance.com, for free downloads of updated software and instruction manuals.

The high detail map data provided with this program is organized into six regions. To install MapCreate, follow the instructions in the manual.

Material covered includes:

New Mapping Data

Topographic elevations, public hunting areas and game management units are discussed along with other new data. Be sure to read the map

data disclaimer following the data descriptions.

Additional Symbols

New hunting-specific symbols make it easier to scout ahead of the hunt and mark important spots.

Searching

MapCreate lets you search for POIs, land features and more, just as you can in a Lowrance GPS unit.

Aviation Searching

Load a card containing a Jeppesen® Aviation Database into the card reader and MapCreate lets you search for items such as airports and VORs.

Find Nearest Waypoint or Nearest Highway Exit

It's easier to find these items with the new right-click shortcut.

Map Category Options Toolbar

A drop-down menu lets you select pre-set or customizable category settings for activities ranging from hunting to aviation.

Routing

MapCreate lets you accurately add POIs, land features and aviation navaids to routes with a click of the mouse.

Dynamic Pan Arrows

The permanent pan arrows that were located along the sides of the Master Map window have been replaced with pop-up pan arrows. You can even pan diagonally!

Pop-up Boxes

Pop-up information boxes for POIs, land features and interstate highway exits now include elevations. Exit pop-up boxes also list nearby exit services.

Color Legend

A legend describes the colors of different areas.

Map Coverage by DVD

The program's map data is provided on one DVD. If you choose to use Full Install, all of the high detail map data will be available from your hard drive. This requires 4.5 GB of space.

A Custom Install lets you select only the help file, sonar viewer, and map data.

The Compact Install loads your hard drive with the basic program, along with navigational aid data and a medium-detail world map. This requires approximately 300 MB of space.

New Mapping Data Types:

Elevation Contour Lines

MapCreate includes topographic elevations for all 50. These are shown as major and minor contour lines, with numbers showing the elevation above sea level. Contour lines begin to appear at about the 60 mile zoom range (depending on your monitor size and resolution). At that zoom level and closer, the mouse pointer also triggers a pop-up box showing elevation at that point.

Hunting

Public Hunting Area boundaries and their names from 48 states are included. Alaska and Hawaii are not included.

Game Management Unit boundaries for 22 states are included, in the following categories: antelope, bear, deer, elk goat, moose, mule deer, sheep, turkey (spring and fall) and whitetail deer.

The GMU states include: Arizona, Colorado, Iowa, Idaho, Kansas, Kentucky, Massachusetts, Minnesota, Missouri, Montana, North Dakota, Nebraska, New Mexico, Nevada, New York, Ohio, Oregon, Pennsylvania, South Dakota, Utah, Wisconsin and Wyoming.

State and federal wildlife refuge and wilderness area boundaries are also included.

Tip:

For links to all 50 state wildlife agency web sites, as well as those of the Canadian provinces and many wildlife conservation organizations, be sure to visit the Lowrance web site, www.lowrance.com.

Other Data Types

There are other areas that are open to hunting in some states or are otherwise important to hunters, and we have included them. These are boundaries for state parks, state forests and military reservations.

Hikers and backpackers as well as hunters will appreciate the addition of intermittent streams. They are just part of the overall improved hydrography data which has better resolution and pop-up names. U.S. coastline and lakeshore detail has been dramatically improved. MapCreate also now includes USGS 1:24000 scale quadrangle map boundaries and their names, which are searchable. This makes it easier to determine what USGS topo maps you may want to purchase for your outdoor adventures. Sections, township and range lines are included. Boundaries have also been added for cities over 2,500 population.

IMPORTANT NOTICE:

Do not rely on this product as your primary source of information for navigation or area boundaries. You are responsible for using official government maps and charts during your outdoor activities. Due to the varied ownership and fluctuating borders of publicly managed hunting lands and game management units, you should also consult boundary signs and other on-site identifiers when using those areas.

Activities on public hunting lands are carefully managed to ensure the future of game and non-game species. You must consult local wildlife agency regulations for the hunting areas you use. The Lowrance web site, www.lowrance.com, contains links to the web sites of all state and Canadian provincial wildlife agencies to help access both hunting regulations and official mapping information. Also, updates to MapCreate's mapping data are ongoing; MapCreate customers may download regional updates of hunting-related data categories from the Lowrance web site.

LEI makes no warranties, express or implied, regarding the maps and information contained in this product, including any implied warranties of merchantability, satisfactory quality, fitness for a particular purpose or non-infringement of third party rights. A full description of our warranty is available in the End User License Agreement in the MapCreate manual.

Hunting Specific Symbols

MapCreate has a basic set of 42 symbols used to represent waypoints or event marker icons. That set contains several hunting symbols – such as deer track and tree stand – but we have added more than a dozen new ones. Now you can use a specific symbol to mark items ranging from turkeys to ATVs and from food plots to buck rubs.

Searching

One of the most powerful new functions in MapCreate 7 is the ability to search for POIs and several types of land features. To launch the com-

mand, click the

FIND button on the Map Navigation toolbar (it looks like

a binocular). The Find Menu appears, with a dialog box for the item's name, and pull down menus for the major category and minor category to search in.

For nearest searches, MapCreate begins looking from the current center of the map. When you select an item from the search results, that item will be snapped to the center of the map. When you search for a river, the map will be centered at the mouth of the river.

You can insert an IMS™ Fishing Hot Spots

map card in the card reader and you can search for several categories of Fishing Hot Spot items. However, you must first locate the desired lake and center it in the map before searching for specific fishing items.

When searching for any map item, you often must know the item's "official" name to locate it (especially the first part of the name). Here's an example search, showing the importance of knowing an official name:

We'll look for Truman Lake, which is located in Henry County, Missouri. All the locals and regular out-of-state visitors know this manmade water body as Truman Lake, but that's not the official name

1. Click the

FIND toolbar button.

2. In the Name box, enter Truman Lake.

3. In the Major Category menu, select Water.

4. In the Minor Category menu, select Lake/River Names, to narrow the search, then click the

FIND button on the menu.

MapCreate displays a list of items, but Truman Lake isn't there! That's because the full name is Harry S Truman Reservoir. Instead of "Truman Lake," just try "Harry," "Harry S" or "Harry S Truman," but don't use "Harry Truman" without the "S" or you'll miss it.

A search for "Harry S Truman" produces a list of possible answers in the middle list window. Scroll through the list and select Harry S Tru- man Reservoir (2). Next, in the bottom list window, click on a location to show it on the map, then click ply zoom in until you see the item you were searching for.

OK to clear the Find menu. Now sim-

When searching for a section of land, it helps to know the legal description of the land you are looking for. Land descriptions are read from left to right, and you must enter your search in the same order. For example, to look for the section containing this property: N 1/2 SE 1/4 SW 1/4, S24, T32N, R18E in Wisconsin, in the Name box you would enter

s24,t32n,r18e, which stands for Section 24, Township 32 North, Range 18 East. Note that capital letters are not needed and the entries are separated by commas with no spaces.

Aviation Searching

With your Jeppesen aviation database you can search for airports, intersections, NDBs and VORs. You can search for intersections only by Identifier. You can search for the other items by Name, Identifier or City.

To find the Bartlesville, Oklahoma, VOR by City,

1. Insert the card containing your Jeppesen database in the card reader, and wait for MapCreate to read the card.

2. Click the

3. In the Name box, enter Bartlesville.

4. In the Major Category menu, select Aviation.

5. In the Minor Category menu, select VORs.

6. In the Search Options box, click By City then click the the menu.

7. Only one "Bartlesville" appears in the results list windows. In the bottom list window, click on Bartlesville, then click OK to clear the Find menu. Now simply zoom in until you see the item you were looking for.

FIND toolbar button.

FIND button on

Find Nearest Waypoint, Highway Exit

Right click on the map and a pop-up menu gives you the option to FIND

NEAREST WAYPOINT or FIND NEAREST INTERSTATE HIGHWAY EXIT. Click the desired

command and MapCreate will search for the item nearest to where you clicked the map. The found item will snap to the center of the map. The command will find the nearest waypoint even if it hasn't been saved yet in a GPS data file.

Map Category Options Toolbar

MapCreate Topo contains a Map Category Options toolbar. The toolbar includes a Map Category Options Widow with one click.

There is a organized map category displays for Aviation, Boating, Driving, Hiking and the default, Hunting. Each display can be customized by turning different categories off and on and there are even two sets called Customize 1 and 2. No matter how much you adjust the displays, you can

VIEW MAP CATEGORY OPTIONS button which opens or closes the

MAP USE drop down list that lets you select from several pre-

return all of them to their defaults by clicking the new

DISPLAY SETTINGS button.

We identify various land types with different colors, and you may want to temporarily turn some categories off for better viewing of some details. For example, in military reservations, the dark blue color nicely identifies the area boundaries, but blue roads don't stand out as they normally do. Before you build a custom the map, just remember to turn the map category back on if you want it included in the custom map.

Routing

MapCreate Topo makes it easier than ever to plan an aviation or other route based on navaids, POIs or land features.

Click the where in the Help documentation) to activate the command. Then, simply click on the desired navaids in order to make your route. Previous versions created an ordinary numbered waypoint where you clicked, which often covered up the item you were routing to. Now, when you click on a named item, a small red route dot appears on top of the item's symbol, and the item's actual name and position appear in the route waypoint list.

When editing routes made in this manner, you can insert additional route waypoints from the master map with a right click, but to delete a point from the route, you must open the route waypoint list and right click the point there.

CREATE ROUTE button (described fully in the manual and else-

RESET CATEGORY

Dynamic Pan Arrows

Previously, MapCreate versions panned the Master Map by clicking on Pan Arrow Buttons that were fixed to the sides of the map window. MapCreate 7 has eliminated those four buttons and replaced them with white pop-up pan arrows. When you move the mouse pointer near the edge of the map, the pointer becomes a Pan Arrow. Just click to see more of the map in the direction indicated. Move the mouse pointer away from the edge and it reverts to the previous command you had selected. You can also point to the corners of the map to pan diagonally.

Pop-up Boxes

Pop-up info boxes for POIs, land features and interstate highway exits now include more information. To display a pop-up box, move your mouse pointer over the item at an appropriate zoom range. Depending on your computer monitor size and resolution, these detailed pop-ups become available beginning somewhere in the 50 to 30 mile zoom ranges. If you don't see the desired information, just zoom in a little closer until it becomes available.

Water pop-ups now show the name of the water body. Interstate highway exit pop-ups show: the exit number, an exit description (usually the name of the cross street), the mile marker and exit services located off the highway within approximately one mile from the exit.

Elevations are shown in pop-ups for POIs, land features and interstate highway exits. Elevation pop-ups can also give you the elevation for points located between the displayed contour lines. For example, in a gradually sloping area between an 850 foot contour line and a 900 foot line, slowly move the mouse pointer between them and you'll see readings such as 887 feet, 871 feet, 869 feet and so on.

Color Legend

Public hunting areas: orange

Wildlife refuges: dark green

U.S. Army Corps of Engineer land: olive green

National forests; state forests; national, state and local parks; golf

courses and other recreation areas: light green.

Swamps: medium green

Military reservations: dark blue

Other public lands (such as airports and universities): white

Notes

+ 78 hidden pages