ROTARY TUMBLER
INSTRUCTIONS AND PARTS LIST
Model
C300
Model
C100
Model
C200
LORTONE
12130 Cyrus Way
Mukilteo, WA 98275
(425) 493-1600
GETTING STARTED
I. Open the Barrel: Remove nut
and washer, press down on bolt
with thumb while lifting up on
outside of outer lid with ngers.
If outer lid is difcult to remove,
insert washer between edge
of outer lid and barrel, twist to
loosen. After outer lid has been
removed, lift inner lid out by
center bolt.
II. Add Rocks: Fill Barrel about 1/2 to 2/3 full of rock.
Rocks should be of assorted sizes for best results.
III. Add Abrasive: Add 60/90 Silicon Carbide Abrasive.
Use 1-1/4 C. for a 12 lb. barrel. Add water to top layer
of rocks and abrasive.
Do not overll.
1
Copyright © 2009 Lortone, Inc
Add rocks
until 2/3 full.
Add water to
top layer of
rocks.
IV. Close the Barrel: Wipe the mating surfaces of the
barrel and inner lid clean with a damp cloth. Press
inner lid into barrel until it rests on shoulder. Press
outer lid rmly down onto the barrel. Install washer
and tighten nut.
Knurled nut only needs to be snug Do Not Use tools
to tighten. Over tightening of the nut can cause the
inner lid to distort and leak.
V. Tumble: Plug the tumbler into a suitable outlet. Place
the barrel on the tumbler making sure the groove in
the barrel nut sits on the tumbler guide. Tumble for 23 days. Open and check the rocks. The rough edges
should be wearing down. After 5-7 days, open the
barrel and rinse the rocks in a bucket of water. DO
NOT put the rinse water down a household drain as it
will clog the drain!
IMPORTANT: Clean the rocks and barrel parts
thoroughly using mild soap and water!
VI. Repeat steps II through V: Use succesively ner
abrasives according to your tumbling instruction
booklet and the chart below:
Step 1 Step 2 Step 3 Step 4
Compound 60/90 120/220 Pre-Polish Polish
Silicon Silicon Aluminum Aluminum
Carbide Carbide Oxide Oxide
12 lb Barrel 1-1/4 C. 1-1/4 C. 1-1/2 C. 1-1/2 C.
Copyright © 2009 Lortone, Inc
2
TROUBLESHOOTING
If your tumbler fails to operate correctly, check the
following:
Barrel does not turn, turns very slowly, or stops after
being placed on tumbler.
No power to unit. Make sure machine is plugged in
correctly.
Make sure electrical circuit is
operational.
Barrel not installed
correctly.
Barrel too heavy. Do not exceed rated capacity.
Drive belt broken. Remove cover and replace belt.
Motor doesn’t run or
runs intermittently.
Barrel leaks or barrel lid comes off during operation.
Align barrel correctly.
Replace motor.
Inner lid not seated
correctly.
Knurled nut over
tightened.
Gas build-up in
barrel.
Barrel or boot
gasket damaged.
3
Copyright © 2009 Lortone, Inc
Make sure inner lid and barrel
shoulder are clean and free of
contaminants.
Make sure inner lid is seated on
shoulder inside barrel.
Tighten knurled nut by hand only
until snug. Do not use tools.
Open barrel occasionally to vent
gas that might be formed during
tumbling.
Replace damaged barrel or boot
gasket.
MAINTENANCE
LORTONE Tumblers are capable of operating 24 hours/
day for years with proper care.
For best operation and results follow these simple, but
important steps:
MOTOR: The motor is designed for continuous use and
does not need oiling or other maintenance. It is normal for
the motor to run hot to the touch.
CLEANING: The outside of the barrel should be kept
clean. Clean by wiping with a wet soapy cloth and
rinse well with fresh water. DO NOT put the barrel in a
dishwasher or clean using solvents. If the outside of the
barrel becomes so slick that it slips on the rollers, roughen
slightly with very ne sandpaper or steel wool.
If you need assistance, please contact:
Lortone Customer Service (425) 493-1600 or
email: equipment@Lortone.com
Copyright © 2009 Lortone, Inc
4
PARTS LIST C100
Part No. Description
A 200-002 Bearing
B 203-920 Bearing, Nylon
C 204-002 Bearing Strap
D 210-023 Belt, Drive
E 210-025 Belt, Idler
F 211-001 Pulley, 1-1/2” x 1/2”
G 211-006 Pulley, 2” x 5/8”
H 211-041 Pulley, 5” x 5/8”
I 300-030 1/6 HP Motor
J 009-005 Shaft with cover
K 481-029 Nut, Hex, 5/16”-18 x 1-1/2”
L 484-015 Bolt, Hex, 1/4”-20, 3/4”
M 484-026 Bolt, Hex, 5/16”-18, 1-1/2”
N 489-012 Washer, Flat, 1/4”
O 009-070 Base
P 009-012 Belt Guard
Q 209-001 Rubber Foot
Part No. Description
020-094 Complete Rubber Barrel Assembly,
12 lb Capacity
R 020-102 Inner Lid w/Bolt
S 020-003 Outer Lid
T 481-070 Knurled Nut
U 240-012 Boot Gasket
V 240-005 Rubber Barrel Only
W 108-001 Barrel Washer
5
Copyright © 2009 Lortone, Inc
C100
A
C
K,M
I
P
J
B
L,N
0
Q
Belts & Pulleys
H
E
F
G
D
V
12 Lb. Barrel
U
R
Copyright © 2009 Lortone, Inc
T
W
S
6
PARTS LIST C200
Part No. Description
A 200-002 Bearing
B 203-920 Bearing, Nylon
C 204-002 Bearing Strap
D 210-023 Belt, Drive
E 210-025 Belt, Idler
F 211-001 Pulley, 1-1/2” x 1/2”
G 211-006 Pulley, 2” x 5/8”
H 211-041 Pulley, 5” x 5/8”
I 300-030 1/6 HP Motor
J 009-006 Shaft with cover
K 481-029 Nut, Hex, 5/16”-18 x 1-1/2”
L 484-015 Bolt, Hex, 1/4”-20, 3/4”
M 484-026 Bolt, Hex, 5/16”-18, 1-1/2”
N 489-012 Washer, Flat, 1/4”
O 009-071 Base
P 009-012 Belt Guard
Q 209-001 Rubber Foot
Part No. Description
020-094 Complete Rubber Barrel Assembly,
12 lb Capacity
R 020-102 Inner Lid w/Bolt
S 020-003 Outer Lid
T 481-070 Knurled Nut
U 240-012 Boot Gasket
V 240-005 Rubber Barrel Only
W 108-001 Barrel Washer
7
Copyright © 2009 Lortone, Inc
C200
A
C
K,M
B
I
P
J
O
L,N
Q
Belts & Pulleys
H
E
G
F
D
V
12 Lb. Barrel
U
R
Copyright © 2009 Lortone, Inc
T
W
S
8
PARTS LIST C300
Part No. Description
A 200-002 Bearing
B 203-920 Bearing, Nylon
C 204-002 Bearing Strap
D 210-023 Belt, Drive
E 210-025 Belt, Idler
F 211-001 Pulley, 1-1/2” x 1/2”
G 211-006 Pulley, 2” x 5/8”
H 211-041 Pulley, 5” x 5/8”
I 300-030 1/6 HP Motor
J 009-007 Shaft with cover
K 481-029 Nut, Hex, 5/16”-18 x 1-1/2”
L 484-015 Bolt, Hex, 1/4”-20, 3/4”
M 484-026 Bolt, Hex, 5/16”-18, 1-1/2”
N 489-012 Washer, Flat, 1/4”
O 009-072 Base
P 009-012 Belt Guard
Q 209-001 Rubber Foot
Part No. Description
020-094 Complete Rubber Barrel Assembly,
12 lb Capacity
R 020-102 Inner Lid w/Bolt
S 020-003 Outer Lid
T 481-070 Knurled Nut
U 240-012 Boot Gasket
V 240-005 Rubber Barrel Only
W 108-001 Barrel Washer
9
Copyright © 2009 Lortone, Inc
C300
C
A
K,M
B
I
P
J
O
L,N
Q
Belts & Pulleys
H
E
G
F
D
V
12 Lb. Barrel
U
R
Copyright © 2009 Lortone, Inc
T
W
S
10
LORTONE Rotary Tumblers
are quiet, durable grinding
and polishing machines.
Follow these basic operating
and care instructions to help
keep your tumbler in optimal
running condition.
LORTONE
12130 Cyrus Way
Mukilteo, WA 98275
(425) 493-1600
Loading...