Lorex LZV2622 SERIES Instruction Manual
Instruction Manual
LZV2622 SERIES 4x MPX
PTZ DOME CAMERA
LZV2622_SERIES_MANUAL_TRILINGUAL_R2
Thank you for purchasing this product. Lorex is committed to providing our customers with a high quality,
reliable security solution.
This manual refers to the following model:
LZV2622
For the latest online manual, downloads and product updates, and to learn about our complete line of
accessory products, please visit our website at:
www.lorextechnology.com
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE
COVER. NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT
TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF THE PLUG
TO THE WIDE SLOT AND FULLY INSERT.
#LX400075; r.34576/35919; en-US
iv
Table of contents
1 Safety Instructions ..............................................................................1
2 Getting Started....................................................................................2
3 Connecting the Camera........................................................................3
4 Installation .........................................................................................4
4.1 Installation Tips and Warnings ....................................................... 4
4.2 Extension Cables........................................................................4
4.2.1 Cable Extension Options ...................................................5
4.2.2 Connection Diagram for Extending the Cables Beyond 60ft
4.3 Installation (Indoor/Outdoor).......................................................... 6
4.3.1 Wall Mounting ................................................................. 6
4.3.2 Ceiling Mounting ............................................................ 11
5 Controlling the PTZ Camera with your MPX DVR.................................... 12
5.1 Controlling a PTZ Camera (Local DVR).......................................... 12
5.2 Advanced PTZ Controls ............................................................. 14
5.2.1 Presets ........................................................................ 14
5.2.2 Tours........................................................................... 15
5.2.3 Pattern......................................................................... 16
6 Technical Specifications..................................................................... 17
6.1 Dimensions ............................................................................. 18
7 Troubleshooting ................................................................................19
8 Notices............................................................................................. 20
8.1 FCC/IC Notice.......................................................................... 20
8.2 Modification............................................................................. 20
8.3 ROHS .................................................................................... 20
(18.2m)..........................................................................5
#LX400075; r.34576/35919; en-US
v
1
Safety Instructions
• Read this guide carefully and keep it for future reference.
• Follow all instructions for safe use of the product and handle with care.
• Use the camera within given temperature, humidity, and voltage levels noted in the
Technical Specifications.
• Camera is rated for outdoor use and is weatherproof when properly installed. Camera
is not intended for submersion in water. Installation under a sheltered environment is
recommended.
• Do not disassemble the camera.
• Do not point the camera directly towards the sun or a source of intense light.
• Use only the supplied regulated power supply. Use of a non-regulated, non-conforming
power supply can damage this product and voids the warranty.
• Make sure to install the camera in a location that can support the camera weight.
• Make sure there are no live electrical cables in the area where you plan to mount the
camera.
• Periodic cleaning may be required. Use a damp cloth only. Do not use anything other
than water to clean the dome cover, as chemicals such as acetone can permanently
damage the plastic.
#LX400075; r.34576/35919; en-US
1
2
Getting Started
The system comes with the following components:
60ft (18.2m) UL Rated
Extension Cable
MPX PTZ Dome Camera
Allen Key (x2)
(One included in the mounting
hardware kit of the camera, and
one included in the mounting
hardware kit of the wall
mounting bracket)
Mounting Template
Wall Mounting Bracket
Installation Diagram Guide and
Instructional Manual
Mounting Screws (x3)
& Anchors (x3)
(For camera)
Mounting Screws ST4 (x4)
& Anchors S6 (x4)
(For wall mounting bracket)
12V DC Power Adapter
Hex Bolt M4x10 (x3)
(For wall mounting bracket)
#LX400075; r.34576/35919; en-US
2
3
Connecting the Camera
NOTE
• It is recommended to connect the camera to your DVR and test the PTZ controls before permanent installation. For instructions on how to setup PTZ controls, see 5 Controlling the PTZ Camera with your
MPX DVR.
• When you first power up the camera and connect it to the DVR, it may take up to 2 minutes for the
camera image to appear.
1. Connect the BNC video connector on the camera cable to the included extension
cable.
2. Connect the female 12V DC power connector on the camera cable to the male power
connector on the included extension cable.
3. Connect the BNC cable on the extension cable to one of the Video Input ports on the
DVR. Make note of the port number where you connect the camera, as it will be used
when configuring the DVR to communicate with the camera.
4. Connect the power connector on the extension cable to the included power adapter.
Plug the power adapter into a power outlet.
CAUTION
• Make sure to disconnect the power adapter before installing the camera. The camera will begin
moving immediately when the power adapter is connected.
NOTE
RS-485 is for service purposes only — not required for controlling MPX PTZ cameras.
#LX400075; r.34576/35919; en-US
3
4
Installation
4.1 Installation Tips and Warnings
• Camera is rated for outdoor use. It is recommended to install the camera in a sheltered
area, such as under the eaves on a roof.
• Use the included wall mounting bracket for wall installation.
Otherwise, the camera image will be sideways. You can also refer to the included
installation diagram guide for wall mounting instructions.
• Camera is capable of seeing in low light conditions (0.1 Lux), but it cannot see in total
darkness.
NOTE
It is recommended to install the camera where there is some ambient light (for example, street lighting
or starlight, moonlight, etc.) or leave some lighting on in the area where the camera is installed.
• Mount the camera in a location that can support the camera weight.
• Mount the camera where the lens is away from direct and intense sunlight.
• Plan your cable wiring so that it does not interfere with power lines or telephone lines.
• Ensure you adhere to local building codes.
• Ensure that the camera wiring is not exposed or easily cut.
• Mount the camera in an area that is visible but out of reach.
NOTE
This camera is suitable for ceiling mounting. Wall mounting requires included wall mount.
4.2 Extension Cables
• The included extension cable is 60ft (18.2m) long. If you are planning on extending the
camera’s video cabling beyond 60ft (18.2m), see 4.2.2 Connection Diagram for Extend-
ing the Cables Beyond 60ft (18.2m).
• Because this is a high-powered PTZ camera, the power cable cannot be extended beyond 60ft (18.2m). You may connect the included power adapter directly to the camera’s power connector and plug the adapter into a power outlet near the camera.
• The RS-485 wires on the camera cable are for service purposes only.
• You can extend the camera’s video with a single cable run of up to 800ft / 242m long
(not included). Video quality may decrease if your extension cable is too long. For this
setup, you must purchase a single run of RG59 coaxial extension cable.
It is recommended to use a video cable with the following specification: RG59U 95%
Braid 20AWG or better.
NOTE
RG59 coaxial cable should be available from your local building supply store.
#LX400075; r.34576/35919; en-US
4
Installation4
4.2.1 Cable Extension Options
Extend the cable run for your camera depending on the cable type used.
Additional extension cables sold separately. See table below:
Option Cable Type Max Cable Run Distance
1
2
3
NOTE
Lorex 60ft (18.2m) BNC / DC
Cable
(Included with camera)
‘RG59’ or ‘Coax’ or ‘Coaxial
BNC’
Siamese (Video and Power)
‘RG59’ or ‘Coax’ or ‘Coaxial
BNC’
(Video Only
2
)
60ft (18.2m)
300ft / 92m
800ft / 242m
1. The extension cable must be a single stretch of cable between the DVR and camera. You cannot
connect multiple extension cables to each other.
2. For cable runs above 300ft / 92m (option 3), you must connect the power adapter directly to the camera, rather than at the end of the extension cable.
3. Indicators that your cable run may be too long:
• Video is permanently black & white (even during day time)
• Video is unclear, soft, or distorted
4. For more information on extension cables, visit www.lorextechnology.com/support
4.2.2 Connection Diagram for Extending the Cables Beyond 60ft (18.2m)
1. Connect the BNC video connector on the camera cable to a single BNC extension
cable up to 800ft / 242m long (not included).
2. Connect the female 12V DC power connector on the camera cable to the included
power adapter. Connect the power adapter to a power outlet.
CAUTION
• Make sure to disconnect the power adapter before installing the camera. The camera will begin
moving immediately when the power adapter is connected.
3. Connect the BNC extension cable to one of the Video Input ports on the DVR. Make
note of the port number where you connect the camera, as it will be used when
configuring the DVR to communicate with the camera.
#LX400075; r.34576/35919; en-US
5
Installation4
4.3 Installation (Indoor/Outdoor)
The camera includes all necessary components for ceiling mounting and wall mounting.
For full instructions on each type of mounting, see 4.3.1 Wall Mounting or 4.3.2 Ceiling
Mounting.
Before installing the camera, decide whether to run the cables through the wall / ceiling
(drilling required) or along the wall / ceiling. If you run the cables along the wall / ceiling,
you must run the cable through the cable notch on the dome camera base. This will keep
the dome camera base flush to the ceiling when mounted.
4.3.1 Wall Mounting
CAUTION
Make sure to install in a location that can support the combined weight of the wall mounting bracket and
the camera.
To wall mount the camera:
1. Use the Allen key (S3.0) included with the wall mounting bracket kit to loosen the hex
lock on the bottom of the wall mounting bracket. Once loose, remove the back plate of
the mounting bracket.
2. Use the Allen key included with the camera mounting kit to loosen the dome camera
cover screws (x3). Remove the dome camera cover.
#LX400075; r.34576/35919; en-US
6
Installation4
3. Insert the camera cable through the hole in the wall mounting bracket.
4. Align the 3 mounting holes on the dome camera base with the 3 corresponding
mounting holes on the wall mounting bracket.
NOTE
Ensure that the cable notch on the dome camera base is aligned with the cable notch on the wall
mounting bracket.
1: Mounting Holes
5. Use the Hex Bolt M4x10 (x3) screws included with the wall mounting bracket kit to
secure the position of the dome camera base.
#LX400075; r.34576/35919; en-US
7
Installation4
6. Holding the flat side of the back plate against the mounting surface, mark holes for the
mounting screws ST4 (x4) and the camera cable. Remove the back plate and drill
where marked.
NOTE
You do not need to mark holes for the camera cable if you plan to run it along the wall / ceiling.
1: Mounting screw ST4 (x4) holes, 2: Camera cable hole
7. Attach the back plate to the mounting surface using the mounting screws ST4 (x4)
included with the wall mounting bracket kit.
NOTE
Use the drywall anchors included with the wall mounting bracket kit if installing on a drywall surface.
#LX400075; r.34576/35919; en-US
8
Installation4
8. Connect the camera cables as shown in the 3 Connecting the Camera section, then
feed the cables through the cable hole in the back plate (attached to the mounting
surface).
CAUTION
If you run the cables along the mounting surface, you must run the cable through the side notch
on the wall mounting bracket. The camera cable will hang alongside the wall mounting bracket —
see image below for reference:
9. Lower the wall mounting bracket onto the back plate. Ensure that the 2 metal flaps on
the back plate lock into the 2 grooves in the wall mounting plate.
#LX400075; r.34576/35919; en-US
9
Installation4
10. Use the included Allen key (S3.0) to tighten the hex lock on the bottom of the wall
mounting bracket.
11. Replace the dome camera cover and tighten the dome camera cover screws using the
Allen key included with the camera mounting kit.
12. Remove the vinyl film from the dome cover once installation is complete.
#LX400075; r.34576/35919; en-US
10
Installation4
4.3.2 Ceiling Mounting
To ceiling mount the camera:
1. Use the mounting template included with the camera mounting kit to mark holes for the
mounting screws (x3) and camera cable.
1. Mounting screw holes; 2. Camera cable hole (Optional)
2. Drill holes for the mounting screws, drywall anchors (optional) and camera cable
(optional).
NOTE
• Use the included drywall anchors if installing on a drywall surface.
• If you are planning on running the cables along the mounting surface, there is no need to drill a
hole for the camera cable.
3. Use the Allen key included with the camera mounting kit to loosen the dome camera
cover screws (x3). Remove the dome camera cover.
4. Connect the camera cables as shown in 3 Connecting the Camera.
5. Mount the dome camera base to the mounting surface using the mounting screws (x3)
and drywall anchors (x3) (optional) included with the camera mounting kit.
6. Replace the dome camera cover and tighten the dome camera cover screws using the
included Allen key.
7. Remove the vinyl film from the dome cover once installation is complete.
#LX400075; r.34576/35919; en-US
11
5
Controlling the PTZ Camera with
your MPX DVR
You can connect the PTZ camera to a MPX DVR to control the camera’s movement. The
camera can accept PTZ commands directly through the video cable (MPX only), so there
is no need to run special wiring (for example, RS-485).
NOTE
For the latest list of compatible DVRs, please visit www.lorextechnology.com/support.
To connect the PTZ camera to a DVR:
1. Connect the camera video cable to one of the Video IN ports on the DVR system as
detailed in 3 Connecting the Camera.
2. Right-click and click Main Menu. Enter the system user name (default: admin) and
password (default: 000000) if prompted.
3. Click
4. Under Channel, select the channel your PTZ camera is connected to.
5. Under Control Mode, select HDCVI.
6. Under Protocol, select HD-CVI.
7. Click OK. You can now control your PTZ camera using the system.
5.1 Controlling a PTZ Camera (Local DVR)
1. In Live View, double-click the channel that has the PTZ camera connected to open in
full-screen.
2. Right-click and click Pan/Tilt/Zoom. Enter the system user name and password if
prompted. The PTZ menu opens.
3. Use the on-screen PTZ controls to control the camera.
>SETTING>PAN/TILT/ZOOM.
#LX400075; r.34576/35919; en-US
12
5
Controlling the PTZ Camera with your MPX DVR
PTZ Controls
1. Direction keys: Click to pan and tilt the camera. Click SIT to stop the current action.
2. PTZ Trace: Click to activate PTZ trace mode. You can do the following:
• Click and drag to move the camera.
• Use the scroll wheel to zoom in and out.
• Right-click to exit and return to normal PTZ controls.
3. Zoom / Focus / Iris: Click +/- to adjust the zoom, focus, and iris.
4. Advanced controls: Click to open advanced PTZ controls.
5. Speed: Enter a PTZ speed from 1 (slowest) to 8 (fastest).
#LX400075; r.34576/35919; en-US
13
5
Controlling the PTZ Camera with your MPX DVR
5.2 Advanced PTZ Controls
Advanced PTZ controls can be used to save camera positions and cycle through various
positions, and automate camera actions.
To open advanced PTZ controls:
• Click the arrow in the PTZ control window to open advanced controls.
Advanced PTZ controls overview:
1. No.: Select the number of the action you want to perform.
2. Not supported.
3. PTZ camera menu: Click to open the camera’s OSD menu. This menu is for advanced
users only.
4. Preset: Click to move the camera to the selected preset location.
5. Not supported.
6. Tour: Click to run the selected tour.
7. Not supported.
8. Pattern: Click to run the selected pattern.
9. Not supported.
10. Not supported.
11.
: Click to open the PAN/TILT/ZOOM menu, where you can set up Presets, Tours,
and Patterns.
5.2.1 Presets
Presets will save the camera’s position for quick retrieval.
To add presets:
1. Click
to open the PAN/TILT/ZOOM menu.
#LX400075; r.34576/35919; en-US
14
5
Controlling the PTZ Camera with your MPX DVR
2. Click the Preset tab.
3. Enter the number of the preset you want to create under Preset.
4. Move the camera to the desired position and click Set.
5. Right-click to return to the advanced PTZ controls window.
To go to a preset:
• Under No., select the number of the preset you would like to go to and click
5.2.2 Tours
Tours will cycle through a set of presets.
To create a tour:
1. Click
to open the PAN/TILT/ZOOM menu.
2. Click the Tour tab.
3. Under Patrol No., select the tour you would like to configure.
4. Under Preset, select a preset you would like to add to the tour.
5. Click Add Preset.
6. Repeat steps 4 and 5 to add additional presets to the tour.
NOTE
.
Click Del Tour to clear all presets from a tour.
7. Right-click to return to the advanced PTZ controls window.
To run a tour:
• Under No., select the number of the tour you would like to go to and click
#LX400075; r.34576/35919; en-US
.
15
5
Controlling the PTZ Camera with your MPX DVR
NOTE
• There is a 5 second minimum pause between presets.
• Tour panning / tilting speed is slower than manual panning / tilting speed. The reduced speed maximizes reliability.
NOTE
The camera's full panning range is 355°. However, we recommend you do not make the camera pan
more than 270° between any two points in a tour.
5.2.3 Pattern
Patterns automatically cycle the camera between two positions.
To create a pattern:
1. Click
to open the PAN/TILT/ZOOM menu.
2. Click the Pattern tab.
3. Under Pattern, enter the pattern you would like to configure.
4. Move the camera into the desired start position and click Begin.
5. Move the camera into the desired end position and click End.
6. Right-click to return to the advanced PTZ controls window.
To run a pattern:
• Under No., select the number of the pattern you would like to go to and click
NOTE
The camera's full panning range is 355°. However, we recommend you do not make the camera pan
more than 270° between any two points in a pattern.
.
NOTE
For instructions on how to control the PTZ camera using the smartphone or tablet app, refer to your DVR's
instructional manual.
#LX400075; r.34576/35919; en-US
16
6
Technical Specifications
Image Sensor 1/2.7", CMOS 2.1 MP
Video Format
Effective Pixels 1928 (H) x 1088 (V)
Resolution Up to 1080p
Range 0°～355° Pan; 0°～90° Tilt
Pan/Tilt Speed Manual Speed — Max 80°/Sec Pan; Max 40°/Sec Tilt
Zoom
Scan System Progressive
Synchronization Internal
S / N Ratio ≥55dB
Iris Auto Iris
AES Shutter Speed 1/1 ~ 1/30,000 Sec.
Min. Illumination 0.1 Lux in Color; 0.05 Lux in Black and White
Lens / Lens Type 2.7mm ~ 11mm ,F1.6 ~ F2.7 / Auto / Manual Focus
Field of View (Horizontal) 95°～30°
Day/Night IR Cut Filter (ICR)
Termination
Video Output BNC
Power Requirement 12V DC
Power Consumption
Operating Temperature Range -22°F ~ 140°F / -30°C ~ 60°C
Operating Humidity Range
Indoor/Outdoor Both (IP66)
Weight (Camera Alone)
Weight (Camera & Wall Mount)
NTSC / PAL
Preset Speed — Max 100°/Sec Pan; Max 60°/Sec Tilt
Tour Speed — Max 80°/sec Pan; Max 40°/Sec Tilt
4x Optical Zoom & 16x Digital Zoom
BNC Video/ DC Power/ RS485 (service only)
Max. 600mA
<95%RH
1
1.20lbs / 0.54kg
2.35lbs / 1.06kg
1. Not intended for submersion in water. Installation in a sheltered location recommended.
#LX400075; r.34576/35919; en-US
17
6
Technical Specifications
6.1 Dimensions
Camera Alone:
Camera and Wall Mount:
#LX400075; r.34576/35919; en-US
18
7
Troubleshooting
There is no picture at night.
• Camera is capable of seeing in extremely low-light conditions (0.1 Lux), but it cannot
see in total darkness.
It is recommended to install the camera where there is some ambient light (for example: street lighting, starlight, moonlight, etc.) or leave a light on in the area where the
camera is installed.
No image at startup.
• When the camera is first powered on, it performs a startup check. It may take up to 2
minutes after startup for the camera image to appear.
• Check to ensure your camera is properly connected (see 3 Connecting the Camera)
and the power adapter is plugged in.
• Connect the power adapter to a different outlet.
• Make sure power adapter is the original one provided (12V DC). Do not use other
power adapters with this product, as this will void the warranty.
No image or camera image is unclear.
• Dome cover is dirty. Clean the dome cover with a soft, slightly damp cloth. Do not use
anything other than water to clean the dome cover, as chemicals such as acetone can
permanently damage the plastic.
• Extension cable run may be too long (see 4.2 Extension Cables for details).
• Voltage may drop over distance and affect image quality. The power adapter must be
connected either at the end of the provided 60ft (18.2m) cable or directly to the camera
cable.
Image is distorted.
• Image may become unclear when camera is tilted too close to the camera base (for example, pointed parallel to the ceiling). Tilt the camera using DVR PTZ controls.
Image is too bright.
• Ensure your camera isn’t pointed directly at a source of light (e.g. sun or spot light).
• Check your DVR’s brightness and contrast settings.
• Move your camera to a different location.
Image is too dark.
• Check your DVR’s brightness and contrast settings.
• Move your camera to a different location.
PTZ controls are not working or are not working properly.
• Extension cables may be damaged or are not connected properly.
Check your extension cable run.
• In your DVR settings, make sure the camera's channel is set to HD-CVI.
DVR motion detection is constantly triggering.
• Turn off motion detection on the channel the PTZ camera is connected to. DVRs use
video motion detection, which means they detect motion by looking for changes between frames (images) in the video. If the camera is moving, the DVR will detect this as
motion.
#LX400075; r.34576/35919; en-US
19
Loading...