Lorex LWB5800 Series, LWB6800 Series Quick Start Manual
Package Contents
* Per camera in multi-camera packs
• HD Wire-Free Security Cameras
• Camera Mounting Kit*
• Rechargeable Power Pack*
• Camera Antenna*
• Allen Key
• Power Pack Adapter
Safety Precautions
• Read this guide carefully and keep it for future reference.
• Follow all instructions for safe use of the product and handle with care.
• Use the camera within given temperature, humidity and voltage levels
noted in the camera’s specifications.
• Do not disassemble the camera.
• Do not point the camera directly towards the sun or a source of
intense light.
• Use only the supplied regulated power supply provided with the
product or compatible accessories. Use of a non-regulated, nonconforming power supply can damage the product and void the
warranty.
• Periodic cleaning may be required. Use a damp cloth only. Do not use
any harsh, chemical-based cleaners.
Available Accessories
The following accessories are available for purchase. Visit lorex.com and
search for the model numbers below for details:
COLOR
WHITE
BLACK
* Compatible with select Wire-Free cameras only. Visit
lorex.com/compatibility for details.
Extra Power
Pack Power
Adapters
ACPWF1
ACPWFBK1
2-cell
Accessory
Power Pack
ACBATT2
ACBATTR2
3-cell
Accessory
Power Pack
PLUS
ACBATT3
ACBATTR3
Solar
Panel
ACSOL1B*
Optimizing Motion Detection
Customize motion detection settings to ensure motion events are being
recorded and reduce false alarms.
To optimize motion detection:
1. Launch the Lorex Cirrus
app.
2. Tap a channel in Live View to
select it.
3. Tap
, then tap Motion.
4. Configure the following as
needed:
a. Sensitivity: The amount of motion needed to trigger recording (e.g., higher
sensitivity requires less motion to trigger recording).
b. Area Selection: Not supported.
c. Distance Setting: Configure distance setting for motion detection. While
watching the camera’s video on your mobile device, recreate a motion event
in front of your camera. The icon will change from
detected by the camera. Change the distance setting if motion detection is
being triggered by unwanted events.
NOTE: Distance will be affected by temperature.
d. Buzzer: Set the recorder to sound an alarm when motion is detected.
5. Tap Save. Repeat for other cameras on the system.
Installation Tips
Follow the tips below for more accurate motion detection and to optimize
battery life:
• See images to the right for ideal setup. It is
recommended to place your camera at least
7ft (2.1m) above the ground and angle it slightly
downward toward the monitoring area, excluding
any busy areas (e.g., sidewalks or roadways).
• Ensure the camera image is free of obstructions
(i.e., tree branches).
• Position the camera no more than 20ft (6.1m)
away from the area you wish to monitor.
• See the “Optimizing Motion Detection” section to
customize motion settings for each camera on
your system.
• For best performance, position the camera so
that objects of interest will move from sideto-side across the camera image, rather than
moving towards or away from the camera.
• Install the camera within range of the recorder (noted in the camera’s
specifications).
• This camera is weather resistant for outdoor use (IP66 rated). Installation in a
sheltered location is recommended.
• Battery life will vary based on temperature, settings and number of events.
a
b
c
d
to when motion is
HD Wire-Free Add-On Camera
Quick Start Guide
English Version 1.0
As our products are subject to continuous improvement, Lorex reserves the right
to modify product design, specifications and prices, without notice and without
Copyright © 2019 Lorex Corporation
incurring any obligation. E&OE. All rights reserved.
LWB5800_LWB6800_QSG_EN_R1
Disclaimers
• For a full list of compatible recorders, visit lorex.com/compatibility.
• Not intended for submersion in water. Installation in a sheltered location
recommended.
LWB5800 / LWB6800 SERIES
lorex.com
STEP 1: Initial Setup
Before you begin, you will need to prepare the wire-free cameras and Power Packs.
NOTE: Power Packs come fully charged with no need for initial charging.
To prepare the cameras:
1. Attach an antenna to
each camera.
2. Peel off the PLEASE REMOVE label
covering the contacts on each Power
Pack. Insert the charged Power Packs
into each camera base. Push up until
the Power Pack ‘clicks’ into place.
NOTE: The camera will 'beep' when the
Power Pack is properly inserted. If you
do hear this alert, remove the Power
Pack by pushing on the release tabs then
re-insert.
STEP 2: Pairing with Lorex Cirrus
Pair your add-on camera to your recorder using the free Lorex Cirrus app for
smartphones and tablets (iOS and Android).
NOTE: Make sure the camera is within 3ft (1m) of the recorder.
To pair the camera with Lorex Cirrus:
1. From Live view, tap any free
channel you would like to
pair a camera to (marked
with a
icon).
2. Tap PAIR. A timer for 30
seconds appears.
3. Press and hold the pair
button on the back of the
camera for 3 seconds.
STEP 3: Installing the Cameras
Follow the instructions below to mount the cameras. It is recommended that you refer to the “Installation Tips” section
to help you select good mounting locations.
To install your cameras:
3. Secure the bracket to the mounting
1. Set the mounting bracket in
the desired mounting position.
Mark holes through the
mounting bracket (shown as
orange X’s on the right).
2. Drill holes where marked for
the mounting screws using
the included drill bit (item C
provided in the toolkit with your
wire-free system).
surface with the included mounting
screws (×4). Make sure all screws
are fastened tightly using the
included screwdriver (item A+B
provided in the toolkit with your
wire-free system).
NOTES:
• Insert the included drywall anchors if you are mounting
the camera onto drywall.
• The hole at the top of the mounting bracket will be used in
step 5, once the camera is attached to the mounting plate.
5. Insert the security screw
through the fasteners on the
4. Lower the camera base
onto the mounting bracket
so the 2 tabs in the
mounting bracket lock into
the 2 slots in the camera
base.
top of the camera base and
mounting bracket to secure
the camera to the mounting
bracket. Tighten using
the included screwdriver
(item A+B provided in the
toolkit with your wire-free
system).
6. OPTIONAL: Tighten the pre-installed locking screw on the base of the Power Pack using
the included screwdriver (item A+B provided in the toolkit with your wire-free system).
NOTE: You will need to loosen the locking screw to remove the Power Pack in the future.
NOTE: A “pairing successful” message should appear on screen. If you do not see this message,
repeat the steps above.
Arm
7. Adjust the angle of the camera.
Use the included Allen Key
to loosen the adjustment
screws labelled below. Tighten
all adjustment screws when
Camera
levelling
angling
Arm
rotation
NOTE: If you are
angling the camera
down and to the right,
position the antenna
as shown to the right.
finished.
8. OPTIONAL: Use the included cable clips to complete the installation. Remove the protective
strip to uncover the adhesive on the cable clip to attach to the mounting surface.
LWB5800_LWB6800_QSG_EN_R1
Power
cable
Mounting
surface
Loading...