Lorex LW4211 User Manual

Package Contents

• 1080p MPX Wireless Security Camera

• Wireless Receiver

• Antennas (×2)*

• Power Adapters (×2)*

• Mounting Kits (×2)*

• Allen Key

• BNC Adapter

* One each for camera and receiver.

A REGULATED UL / CSA APPROVED power supply is REQUIRED for use
with this camera (included). Use of a non-regulated, non-conforming
power supply can damage this product and voids the warranty.

ATTENTION:

Safety Precautions

• Read this guide carefully and keep it for future reference.

• Follow all instructions for safe use of the product and handle with care.

• Use the camera within given temperature, humidity and voltage levels noted in the
camera’s specifications.

• Do not disassemble the camera.

• Do not point the camera directly towards the sun or a source of
intense light.

• Use only the supplied regulated power supply provided with the product. Use of a
non-regulated, non-conforming power supply can damage the product and void the
warranty.

• Periodic cleaning may be required. Use a damp cloth only. Do not use any harsh,
chemical-based cleaners.

Installation Tips

To ensure the best possible wireless performance, it is recommended to keep the
following installation tips in mind when choosing a location for the camera:

• Ensure your camera is placed as close to your receiver as possible.

• Reduce the number of obstructive materials between the camera and the receiver.
Concrete, brick, metal and wood are the most common materials in your house that
can cause poor signal strength.

• The camera uses the 2.4GHz band exclusively. Most new routers support both

2.4GHz and 5GHz bands. It is recommended to use other WiFi-connected devices
using the 5GHz band when possible to ensure the 2.4GHz band is not overcrowded.

• Other electronic devices such as microwaves, TVs, cordless phones, and baby
monitors can cause signal interference. It is recommended to install the camera as
far away from these devices as possible.

Resources

Need Help?

Visit us online for up-to-date software and complete

instruction manuals

1

2

3

4

Dimensions

2.8”

70mm

Visit lorex.com

Search for the model number

of your product

Click on your product in the

search results

Click on the Downloads tab

5.4”

138mm

6.1”

155mm

4.5”

114mm

1080p MPX Wireless Security Camera

Quick Start Guide

English Version 1.0

• Point the camera where there is the least amount of obstructions (i.e., tree
branches).

• Install the camera where vandals cannot easily reach.

• This camera is rated for outdoor use. Installation in a sheltered location is
recommended.

Disclaimers

• For a full list of compatible recorders, visit lorex.com/compatibility

• Not intended for submersion in water.

4.4”

113mm

Copyright © 2018 Lorex Corporation
As our products are subject to continuous improvement, Lorex reserves the right
to modify product design, specifications and prices, without notice and without
incurring any obligation. E&OE. All rights reserved.

LW4211_QSG_EN_R1

LW4211 SERIES

www.lorex.com

Installing the Camera

• Test your camera prior to selecting a permanent mounting location by temporarily
connecting the camera and cable to your DVR.

• Ensure the camera is no more than 700ft (213m) away from the wireless receiver in
an open field (with line of sight between antennas). The range is approximately 115ft
(35m) or less in an indoor environment, depending if there are walls or obstructions
between the camera and receiver.

• Review the ‘Installation Tips’ section before choosing a mounting location for the
camera.

Before Installing the Camera

• Decide whether to run the cables through the wall /
ceiling (drilling required) or along the wall / ceiling.

• If you run the cables along the wall / ceiling, you must
run the cable through the cable notch on the base.
This will keep the camera base flush to the surface
when mounted.

To install your camera:

Mounting Screws (×3)

1. Use the included mounting template or camera base to mark
holes for the included mounting screws. Drill holes where
marked.

NOTE: Ensure one of the included antennas is properly

attached to the camera.

2. Mount the camera to the mounting surface using the
included mounting screws (×3).

NOTE: Use the included drywall anchors (×3) if installing

into drywall.

3. Adjust the angle of the camera until the desired view is set.
Tighten the screws to secure the camera position.

A. Use the included Allen key to
loosen the adjustment screw
on the camera base. Rotate the
arm of the camera up to 360°,
then tighten the screw.
B. Use the included Allen key to
loosen the adjustment screw.
Bend the arm of the camera up
to 90°, then tighten the screw.
C. Use the included Allen key to
loosen the adjustment screw furthest from the camera base. Rotate
the camera until it is level with the viewing area, then tighten the
screw.

4. Connect the camera power adapter to the camera cable.
Connect the power adapter to a power outlet.

5. Remove protective film from the camera lens.

This camera includes an Auto Mechanical IR Cut Filter. When the camera changes
between Day/Night viewing modes, an audible clicking noise may be heard from the
camera. This clicking is normal, and indicates that the camera filter is working.

IMPORTANT:

Camera Base

ATTENTION:

Cable
Notch

Mounting Surface

Drywall Anchors (×3)

B

A

C

LW4211_QSG_EN_R1

Setting Up the Receiver

Connecting the receiver directly to DVR:

1. Ensure one of the included antennas is properly attached to the
receiver.

2. Connect the receiver’s BNC cable to a compatible DVR’s video
input*.

3. Connect the receiver power adapter to the receiver. Connect the
power adapter to a power outlet.

NOTE: Make sure to first connect and power on the camera before

powering on the receiver.

4. (Optional) Use the included double-sided tape to securely attach
the receiver to a flat surface.
(OR)
Secure the receiver to a flat surface using the included mounting
screws.

Connecting the receiver to DVR using a BNC extension cable:

Male Power

Receiver

Connect the male power
head to the female
power head on the
receiver.

Connect the BNC
connector on the extension
cable to the included
BNC adapter. Connect
the adapter to the BNC
connector on the receiver.

**

Female Power

DVR

Connect the BNC connector
to a video input on your DVR.

Connect the female power head
to the included receiver power
adapter.

BNC Adapter

* This camera is only compatible with select DVRs. For a full list of
compatible recorders, visit lorex.com/compatibility.
** Not included. Compatible BNC extension cable available at lorex.com.

Pairing the Camera

The camera and receiver have already been paired out of the box. If for some
reason the pairing is lost, follow these steps to pair the camera and receiver.

To pair the camera and receiver:

1. Make sure that the camera and receiver are
both powered up and all antennas properly
attached.

2. Press the pair button on the receiver (see
Figure 1).

3. Press and hold the pair button on the back
of the camera within 30 seconds of pressing
the pair button on the receiver (see Figure

2). If successful, live video from the camera
will appear on the monitor.

Figure 1

Figure 2

Pair Button on
the Receiver

Pair Button on
the Camera

Installing Multiple Wireless Cameras

When installing multiple digital wireless security cameras in the same
environment, maintain at least 4” / 10cm between the receivers to
optimize camera performance.

NOTE: It is not recommended to install more than 3 digital wireless

security cameras in the same environment to maintain optimal video
frame rate performance.

Audio Settings

Audio recording without consent is illegal in certain jurisdictions. Lorex Corporation
assumes no liability for use of its products that does not conform with local laws.

Audio is disabled by default. If needed, you can enable audio through a Lorex DVR.

To enable camera audio on LHA Series DVRs:

1. In Live View, right-click anywhere on the screen to open the Quick Menu.

2. Click Main Menu. If prompted, enter the system user name and password.

3. Under Settings on the left-side panel, click Recording, then click the Mainstream
tab.

4. Select a channel where an audio camera is connected next to Channel.

5. Check the Audio checkbox to enable audio. Click Save to apply changes.

6. Repeat steps 4 and 5 for any other audio cameras you want to enable audio for.

7. (Optional) Click the Substream tab and perform the same steps to enable audio
when viewing cameras through the computer or mobile applications.

To enable camera audio on LHV / DV Series DVRs:

1. In Live View, right-click and click Main Menu. Enter the system user name and
password.

2. Click (

3. Under Channel, select the channel where the audio-capable camera is connected.

4. Under Audio/Video, check the box on the left to enable audio recording.

5. Under Audio Format, select the format that will be used to record audio. G711a is
recommended.

6. Click OK to save changes.

7. (Optional) Under Audio/Video, check the middle box to enable audio when viewing
cameras through the computer or mobile applications.

NOTE: These instructions are based on current DVR interface. For the most up-to-

date instructions, see your DVR’s instruction manual on lorex.com.

) and select Recording > Recording.

ATTENTION: