Lorex LW2731AC1 SERIES Quick Start Manual
www.lorextechnology.com
LW2731AC1 Series Quick Start Guide_R1 Page 1
For more information, refer to the User’s
Guide or visit
DIGITAL WIRELESS INDOOR/OUTDOOR ACCESSORY MOTION CAMERA
LW2731AC1 SERIES - QUICK START GUIDE
SIMPLY AWARE
™
CONTENTS:
Quick Start Guide
Digital Wireless Color
Camera with Stand
Wireless Antenna
for camera
Power Adapter
for camera
Mounting
Hardware Kit
CAMERA SETUP
1. Connect the new camera to a power outlet. Place the
camera and LCD receiver within 1ft of each other.
2. Press on the wireless receiver.
3. From the Main Menu, press left and right to select
Pairing and press the OK button.
4. Select a channel and press the OK button.
• If you pair a new camera to a channel that is already
being used by an existing camera, the new camera will be
connected to that channel. The old camera will
automatically be disconnected.
5. Following the on-screen prompt, press the Pair button
behind the camera. You have 30 seconds to press the
Pair button on the camera. Once paired, the camera will
be immediately displayed on-screen.
• If you do not press the Pair button on the camera during
the 30 second pairing window, repeat steps 2~5 to try the
pairing process again.
• If the speaker begins squealing, move the camera and
receiver away from each other.
ADDING THE ACCESSORY CAMERA TO YOUR SYSTEM
The Pairing function connects your accessory camera to the system (connect up to 4 cameras) and assigns it
to a channel. By default, the camera(s) that came with the system are automatically paired to channels 1 and
2 on the wireless receiver. To pair an additional camera:
ATTENTION: This camera includes an Auto
Mechanical IR Cut Filter. When the camera
changes between Day/Night Lighting, an
audible clicking noise may be heard coming
from the camera. This clicking is normal, and
indicates that the camera filter is working.
4 5
Pairing Button
5
1. Attach the camera to the stand
and place it on a table or flat
surface.
2. Connect one end of the camera
power adapter to the camera
and the other end to an electrical
outlet. Make sure the power
connector is fully pushed in to
avoid water getting in the plug.
3. Remove the protective film from
the front of the camera.
www.lorextechnology.com
LW2731AC1 Series Quick Start Guide_R1 Page 2
For more information, refer to the User’s
Guide or visit
• Mount the camera indoors or outdoors.
For outdoor installation, mount it in a
sheltered place where it is not directly
exposed to rain or snow.
• Aim the cameras for the best possible
viewing area: select a location for the
camera that provides a clear view of the
area you want to monitor, which is free
from dust, and is not in line-of-sight to a
strong light source or direct sunlight.
• Avoid installing the cameras where
there are thick walls, obstructions, or
interference (i.e. transformers, microwave
ovens or other electrical equipment)
between the cameras and the receiver.
• Select a location for the camera with
an ambient temperature between
14°F~122°F (-10°C~50°C)
• Before starting permanent installation,
have another person hold the camera for
you while you check the signal strength
and image quality on the monitor.
INSTALLING THE CAMERA
INSTALLATION WARNINGS
1. Carefully unpack the camera.
2. Mount the stand to the wall or
ceiling (for ceiling mounting you
may need to move the antenna
sightly down):
• Mark the position of the screw
holes on the wall/ceiling.
• Drill holes and insert the drywall
plugs as needed.
• Firmly attach the stand to the wall
using the provided screws.
3. Screw the antenna onto the
camera.
4. Attach the camera to the stand
either at the bottom or back of
the camera. For ceiling mounting
attach to the back thread. Loosen
the thumbscrews to adjust position
of the camera and tighten to fix
position.
5. Remove the protective film from
the front of the camera.
CAMERA OVERVIEW
1. Microphone: Built-in microphone
2. Lens: Camera lens
3. PIR Sensor: Passive IR motion sensor
4. Speaker: Speaker for intercom
5. Night Vision IR: Night vision IR LEDs
6. Pair: Pairing button
7. Antenna: Wireless antenna
8. Power Cable
7
8
4
6
5
1
2
3
SIMPLY AWARE
™
DIGITAL WIRELESS INDOOR/OUTDOOR ACCESSORY MOTION CAMERA
LW2731AC1 SERIES - QUICK START GUIDE
• Before you install the camera, carefully plan where and how it will
be positioned, and where you will route the cable that connects the
camera to the power adapter.
• Avoid installing in a location which requires the wireless signal to
pass through cement, concrete and metal structures. This will
reduce the transmission range.
• It is recommended to pair the accessory camera to the receiver
before permanently mounting the camera. For detailed information,
please see reverse.
Loading...