Lorex LW2711AC1 Quick Start Manual

www.lorextechnology.com

LW2711AC1 Series Quick Start Guide_R1 Page 1

CONTENTS:

Quick Start Guide

Digital Wireless Color

Camera with Stand

Wireless Antenna

for camera

Power Adaptor

for camera*

• Mount the camera indoors or outdoors. For outdoor
installation, mount it in a sheltered place where it is not
directly exposed to rain or snow.

• Aim the Cameras to best optimize the viewing area:
Select a location for the camera that provides a clear
view of the area you want to monitor, which is free from
dust, and is not in line-of-sight to a strong light source or
direct sunlight.

• Avoid installing the cameras where there are thick
walls, obstructions, or interference (i.e. transformers,
microwave ovens or other electrical equipment) between
the Cameras and the Receiver.

• Select a location for the camera that has an ambient
temperature between 14°F~122°F (-10°C~50°C)

• Before starting permanent installation, have another
person hold the camera for you while you verify its
performance by observing the image on a monitor.

INSTALLING THE CAMERA

Before you install the camera, carefully plan where and

how it will be positioned, and where you will route the

cable that connects the camera to the power adaptor.

INSTALLATION WARNINGS

1. Carefully unpack the Camera.

2. Mount the stand to the wall or
ceiling (for ceiling mounting you
may need to move the antenna
sightly down):

• Mark the position of the screw holes
on the wall/ceiling.

• Drill holes and insert the drywall
plugs as needed.

• Firmly attach the stand to the wall
using the provided screws.

3. Screw on the Antenna to the
Camera prior to mounting.

4. Screw the camera to the stand by
attaching it either at the bottom or
back of the camera. For ceiling
mounting attach to the back thread.
Loosen the thumbscrews to adjust
position of the camera and tighten
to fix position.

*May not be exactly as shown

NOTE: AVOID INSTALLING IN A

LOCATION WHICH REQUIRES

THE WIRELESS SIGNAL TO
PASS THROUGH CEMENT,

CONCRETE AND METAL

STRUCTURES. THIS WILL REDUCE

THE TRANSMISSION RANGE.

Mounting

Hardware Kit

DIGITAL WIRELESS INDOOR/OUTDOOR
ACCESSORY MOTION CAMERA

LW2711AC1 SERIES - QUICK START GUIDE

CAMERA OVERVIEW

1. PIR Sensor: Passive IR motion sensor for more accurate

motion detection.

2. Microphone: Built-in microphone for listening in.

3. Camera Lens

4. Night Vision IRs: For viewing in complete darkness.

5. Speaker: For two-way audio.

6. Pairing Button: See manual for more details.

7. Antenna: Detachable antenna.

8. Power Cable

SIMPLY AWARE

™

7

8

5

6

4

1

2

3

www.lorextechnology.com

LW2711AC1 Series Quick Start Guide_R1 Page 2

CONNECTING CAMERA POWER ADAPTOR

Connect one end of the camera Power Adaptor to the camera and the other end to an electrical outlet.

It’s all on the Web

For detailed setup information,
please refer to your User’s Manual.
For additional information, please
visit our website

www.lorextechnology.com

1. Press MENU on the wireless receiver or remote control.

2. From the Main Menu, select Pairing and press the

Enter button.

3. Select an empty camera channel and press the Enter/
OK button.

NOTE: If you selected a preassigned camera channel, the

new camera will take the place of the existing camera.
You will need to repeat the pairing process for the existing
camera to pair it back to the system.

4. Following the on-screen prompt, press the Pair button
on the rear panel of the camera. You have 30 seconds
to press the PAIR button on the camera. Once paired,
the camera will be immediately displayed on-screen.

NOTE: If you do press the Pair button on the camera during
the 30 second pairing window, repeat steps 1~5 to try the
pairing process again.

ADDING THE ACCESSORY CAMERA TO YOUR SYSTEM

The Pairing Function assigns each camera to a different
channel on the wireless receiver (connect up to 4
Cameras), and is necessary for configuring additional
cameras. By default the cameras that came with the system
are preassigned to channel no. 1 for camera 1 etc.

NOTE: It is recommended to pair the Accessory Camera to
the Receiver before permanently mounting the camera. For
detailed information, please check the owners manual for
the complete system available at www.lorextechnology.com

Connect power adaptor to
local 120V AC power outlet

DIGITAL WIRELESS INDOOR/OUTDOOR
ACCESSORY MOTION CAMERA

LW2711AC1 SERIES - QUICK START GUIDE

SIMPLY AWARE

™

ATTENTION: This camera includes an Auto

Mechanical IR Cut Filter. When the camera

changes between Day/Night Lighting, an

audible clicking noise may be heard coming

from the camera. This clicking is normal, and

indicates that the camera filter is working.

Pairing Button