Lorex LW2301AC1 Series Quick Start Manual

www.lorexcctv.com

LW 2 301AC 1 SERI E S QSG _ EN_R1 Page 1

CONTENTS:

Quick Start Guide

Digital Wireless Color

Camera with Stand

Wireless Antenna

for camera

Power Adaptor

for camera*

• Aim the Cameras to best optimize the viewing area:
Select a location for the camera that provides a clear
view of the area you want to monitor, which is free from
dust, and is not in line-of-sight to a strong light source
or direct sunlight.

• Avoid installing the cameras where there are thick
walls, obstructions, or interference (i.e. transformers,
microwave ovens or other electrical equipment)
between the Cameras and the Receiver.

• Select a location for the camera that has an ambient
temperature between 14°F~122°F (-10°C~50°C)

• Before starting permanent installation, have another
person hold the camera for you while you verify its
performance by observing the image on a monitor.

INSTALLING THE CAMERA

Before you install the camera, carefully plan where and how it will be

positioned, and where you will route the cable that connects the

camera to the power adaptor.

INSTALLATION WARNINGS

1. Carefully unpack the Camera.

2. Mount the stand to the wall:

• Mark the position of the
screw holes on the wall.

• Drill holes and insert the
drywall plugs as needed.

• Firmly attach the stand
to the wall using the
provided screws.

3. Attach the Antenna to the
Camera prior to mounting.

4. Place the camera in the
desired mounting position.
Tighten the thumbscrews
to secure the camera to the
Stand. Adjust the angle of
the camera until the
desired view is set.

*May not be exactly as shown

NOTE: AVOID INSTALLING IN A

LOCATION WHICH REQUIRES

THE WIRELESS SIGNAL TO PASS

THROUGH CEMENT, CONCRETE

AND METAL STRUCTURES. THIS

WILL REDUCE THE

TRANSMISSION RANGE.

Mounting

Hardware kit

COLOR DIGITAL WIRELESS INDOOR/OUTDOOR
ACCESSORY MOTION CAMERA

LW2301AC1 SERIES - QUICK START GUIDE

CAMERA OVERVIEW

1. PIR Sensor: Passive IR motion sensor for more accurate
motion recording.

2. Microphone: Built-in microphone underneath camera body.

3. Lens: Camera lens.

4. Night Vision IR: Night vision IR LEDs used for viewing in
complete darkness.

5. Pair: Pairing button.

6. Antenna: Wireless antenna.

7. Power Cable: Connect the included power adapter to the
cable extending from the camera.

www.lorexcctv.com

LW 2 301AC 1 SERI E S QSG _ EN_R1 Page 2

CONNECTING CAMERA POWER ADAPTOR

Connect one end of the camera Power Adaptor to the camera and the other end to an electrical outlet.

It’s all on the Web

For detailed setup information,
please refer to your User’s Manual.
For additional information, please
visit our website

www.lorexcctv.com/support

1. Press MENU on the wireless receiver or remote control.

2. From the Main Menu, select Pairing and press the
Enter button.

3. Select Camera 2, Camera 3 or Camera 4 and press the
Enter button.

4. Following the on-screen prompt, press the Pair button
on the rear panel of the camera. You have 30 seconds
to press the PAIR button on the camera. Once paired,
the camera will be immediately displayed on-screen.

NOTE: If you do press the Pair button on the camera during
the 30 second pairing window, repeat steps 1~4 to try the
pairing process again.

Pairing Button

ADDING THE ACCESSORY CAMERA TO YOUR SYSTEM

The Pairing Function assigns each camera to a different
channel on the wireless receiver (connect up to 4
Cameras), and is necessary for configuring additional
cameras. By default the camera that came with the
LW2301 system is assigned to channel no. 1.

NOTE: It is highly recommended to pair the Accessory
Camera to the Receiver before permanently mounting the
camera. For detailed information, please check the
owners manual for the LW2301 system available at
www.lorexcctv.com

Connect power adaptor to
local 120V AC power outlet

COLOR DIGITAL WIRELESS INDOOR/OUTDOOR
ACCESSORY MOTION CAMERA

LW2301AC1 SERIES - QUICK START GUIDE