Lorex LW2297 series Quick Start Manual
WIRELESS DIGITAL SECURITY CAMERA
LW2297 SERIES
QUICK START GUIDE
A. Installing the Camera
B. Connecting the Receiver to a DVR
Connect the BNC cable to your
DVR’s video input.
1
Mount the camera to the wall or ceiling using the
included screws. Use the included anchors as needed.
1
2
Connect the camera power adapter
to the camera. Connect power
adapter to a 120V AC power outlet.
Before you permanently install your camera:
ATTENTION: Make sure to first
connect and power on the camera
before powering on the receiver.
LW2297_SERIES_QSG_EN_R1
Getting Started
3
Loosen the
adjustment ring (1).
Adjust the angle of
the camera until the
desired view is set.
Tighten the adjustment ring to secure
the camera position.
2
3
Connect the receiver
power adapter to
the receiver. Connect
the power adapter to
a 120V power outlet.
This system comes with the
following components:
1x wireless camera
1x wireless receiver
1x antenna for camera (pre-attached)
1x antenna for receiver (pre-attached)
2x power adapters (for camera and receiver)
1x BNC-to-RCA adapter
1x camera mounting kit
2x double-sided tape for receiver
1
Installation Tips
Plan where and how they will be
positioned.
Determine where you will route the
cable that connects the camera to the
power adapter.
Verify the camera’s performance by
observing the image on a monitor when
the camera is positioned where it will be
permanently installed.
Avoid installing the camera in a location where
the wireless signal must pass through cement,
concrete, or metal structures. This will reduce
the transmission range.
Power cables are only weatherproof when fully inserted
at the connection point. Power cables should not be
submerged in water.
For outdoor use, installation in a
sheltered location is recommended.
NOTE: It is not recommended to install more
than 4 digital wireless security cameras in the
same environment to maintain optimal video
frame rate performance.
Installing Multiple Wireless
Cameras
When installing multiple digital wireless
security cameras in the same environment,
maintain at least 4” / 10cm between the
receivers to optimize camera performance.
NOTE:
If you run the cables
along the wall / ceiling,
you must run the cable
through the cable notch
on the base. This will
keep the camera base
flush to the wall /
ceiling when mounted.
Cable Notch
Connecting to a TV:
Connect the other end of the adapter to the
video input on your TV. Connect the RCA
cable from the receiver to the audio input on
your TV. Select the input for your camera on
the TV.
Connect the included BNC-to-RCA adapter to
the BNC connector on the receiver.
4
Remove protective film from the
camera lens.
Connect the RCA cable to the
corresponding DVR audio input
(e.g. Video Input 1 / Audio Input 1)
BNC video*RCA audio
RCA audio
BNC video
4
Use the double-sided
tape to securely attach
the receiver to a flat
surface.
OPTIONAL:
* BNC-to-RCA adapter attached.
For support and instructions:
Visit www.lorextechnology.com
Search your product’s model number
Select your product from the search results
Click on the Downloads tab
1
2
3
4
C. Pairing the Camera with a Receiver
NOTE: The camera and receiver have already
been paired out of the box. If for some reason
the pairing is lost, follow these steps to pair the
camera and receiver.
1
Make sure that the camera and
receiver are both powered up and
all antennas properly attached.
2
Press and hold the
PAIR button on
the receiver for 5
seconds to activate
pairing mode. The
pairing status LED
will flash on and
off slowly.
Press the PAIR button on
the back of the camera
within 30 seconds of
pressing the PAIR button
on the receiver. If pairing
is succesful, live video
from the camera will
appear on the monitor.
3
Compatible camera extension cable CBL6WRB (6.6ft/2m) available at www.lorextechnology.com.
Pairing
Status LED
Pair Button
Loading...