Lorex LEV2724 SERIES, LEV2724B SERIES, LEV2724BP SERIES, LEV1522 SERIES Quick Start Manual

FOR SUPPORT AND INFORMATION,

VISIT WWW.LOREXTECHNOLOGY.COM

120mm / 4.7”

Copyright © 2015 Lorex Corporation
As our products are subject to continuous improvement, Lorex reserves the right to modify product
design, specifications and prices, without notice and without incurring any obligation. E&OE

WARNING - A REGULATED 12V DC power supply is REQUIRED for use

with this camera. Use of a non-regulated, non-conforming power supply can
damage this product and voids the warranty.

HD 1080P WEATHERPROOF

MOTORIZED VARIFOCAL SECURITY CAMERA

Quick Start Guide

English Version 2.0

LEV2724 SERIES

Dimensions

Warning/Caution

• Read this guide carefully and keep it for future reference.

• Follow all instructions for safe use of the product and handle with care.

• Use the camera within given temperature, humidity, and voltage levels noted in
‘Camera Specifications’.

• Do not disassemble the camera.

• Do not point the camera directly towards the sun or a source of intense light.

• Use only the supplied regulated power supply. Use of a non-regulated, non­conforming power supply can damage this product and voids the warranty.

• Periodic cleaning may be required. Use a damp cloth only. Do not use harsh
cleaners or aerosol cleaners.

• UL or ETL (CM type) cable is provided with the camera for in-wall installation.
For between-floor installations, a UL or ETL (CMR type) cable is required which is
available at www.lorextechnology.com. Not for Plenum area installation.

Installation Tips

• Point the camera where there is the least amount of obstructions
(i.e. tree branches).

• Install the camera in a location that is difficult for vandals to reach.

• Secure cabling so that it is not exposed or easily cut.

• Camera rated for outdoor use. Installation in a sheltered location recommended.

Contents

• Weatherproof HD dome camera

• Mounting kit

• Allen key

• 60ft UL (CM type) Rated BNC / power extension cable

• Power adapter

86mm / 3.4”

Features

• High Performance 1080p Sony Exmor™ Image Sensor*

• Quick and easy camera view adjustment from your DVR or mobile device with
3x optical zoom lens**

• 960H analog video output for convenient set up or connecting to legacy 960H
DVRs

• Night vision range up to 150ft (46m) in ambient lighting & 100ft (31m) in total
darkness***

• Close up recognition in the dark with SmartIR

• High Dynamic Range (“WDR” in menu) for viewing in extremely challenging
lighting scenarios

• ClearNight imaging for superior low light performance, improving recording
efficiency

• Weatherproof for outdoor & indoor installation (IP66 Rated)****

• Extreme temperature performance (–22° ~ 140°F / –30° ~ 60°C)

• 34-90° remotely adjustable field of view (Horizontal)**

• 3-axis design for wall / ceiling mounting

Disclaimers:

* 1080p cameras are compatible with 1080p HD DVR recorders. 720p cameras are compatible
with 720p & 1080p HD DVR recorders. This product is also compatible with 960H analog DVRs
using the analog BNC connector.
** Camera control is only compatible with Lorex HD LHV Series DVRs. To control a camera on an
analog/960H DVR, use the OSD controller on the camera cable.
*** Stated IR illumination range is based on ideal conditions in typical outdoor night time
ambient lighting and in total darkness. Actual range and image clarity depends on installation
location, viewing area and light reflection / absorption level of object.
**** Not intended for submersion in water. Installation in a sheltered location recommended.

On-Screen Display (OSD) Menu

MPX / HD Video Output

To use the OSD menu, access the PTZ menu of your DVR. See your
DVR’s instruction manual for more details.

Analog Video Output

Configure OSD menu options using the integrated control
stick on the camera cable (see image to the right).

• OPTIONAL: Connect a test monitor to the camera’s

analog (yellow) BNC connector.

• Push the middle of the joystick to open the OSD menu.

• Move the joystick / to select a setting, then
/ to change the setting value.

• Push the middle of the joystick to confirm selection.

• Arrows beside settings indicate a submenu ( ). Select the setting

and push the joystick to enter.

• Select RETURN and push the joystick to return to the previous menu,

or EXIT from the main menu to exit.

NOTE: Camera control through the DVR is only compatible with Lorex
HD LHV Series DVRs. To control a camera on an analog/960H DVR,
use the OSD controller on the camera cable.

Language
Video Format
Backlight OFF

WDR / HDR (HD only)
BLC

HLC
DNR
Advanced Lens ELC

ALC

Exposure Brightness

Shutter
Sens-Up
AGC

White Balance Auto

ATW
Preset
Manual

Day&Night Mode

Delay
D N Level
N D Level
Smart IR
Smart IR Level

Image Sharpness

Color Gain
Freeze
Flip
D-Zoom
Defog

Special Black Level

Privacy
DP Comp

Reset
Version
Exit

Before installing the camera:

• Decide whether to run the cables
through the wall / ceiling (drilling
required) or along the wall / ceiling.

• If you run the cables along the wall /
ceiling, you must run the cable through
the cable notch on the base. This will
keep the camera base flush to the wall /
ceiling when mounted.

To install the camera:

1. Use the included Allen key to loosen the screws on the
dome cover.

2. Rotate the camera base counterclockwise to separate it
from the ball camera and dome cover.

3. Feed the BNC / power cable through the camera
base. If you are running the cables against a wall or
ceiling, make sure to pass the cable through the cable
notch as shown above.

4. Connect the video and power cable as shown in the
section ‘Connecting the Camera‘.

5. Mount the camera base to the mounting surface using
the included screws and drywall anchors (optional).

6. Position the dome cover over the camera and screw it
clockwise halfway onto the camera base.

7. Move the ball camera to the desired position. While
holding the ball camera firmly in place, screw the
dome cover the rest of the way to secure it to the
camera base. Holding the camera prevents it from
moving while installing the dome cover.

8. Use the included Allen key to tighten the screws on the
dome cover.

Cable Notch

To Camera: To Monitor/DVR:

Male Power

BNC

1. Connect the BNC and
power connectors to the
camera. See ‘Camera Wiring’
for details.

Female Power

Camera Wiring

Installing the Camera

Connecting the Camera

ATTENTION - Test the camera prior to selecting a permanent mounting

location by temporarily connecting the camera(s) and cables to the DVR.

Cable Extension Options

Extend the cable run for your camera depending on the cable type
used. Additional extension cables sold separately. See table below:

Option Cable Type Max Cable Run

Distance

1 Lorex model MCBL-60BNCU BNC Cable

(included with camera)

60ft / 18m

2 ‘RG59’ or ‘Coax’ or ‘Coaxial BNC’

Siamese (Video and Power)

300ft / 92m

3 ‘RG59’ or ‘Coax’ or ‘Coaxial BNC’

(Video Only2)

800ft / 242m

Notes:

1. The extension cable must be a single stretch of cable between the DVR and
camera. You cannot connect multiple extension cables to each other.

2. For cable runs above 300ft / 92m (option 3), you must connect the power
adapter directly to the camera, rather than at the end of the extension
cable.

3. Indicators that your cable run may be too long:

• Video is permanently black & white (even during day time)

• Video is unclear, soft, ordistorted

4. For more information on extension cables, visit

www.lorextechnology.com/support.

Problem Solution

No picture / signal • 1080p cameras are compatible with 1080p HD

DVR recorders. 720p cameras are compatible
with 720p & 1080p HD DVR recorders. This
product is also compatible with 960H analog
DVRs using the analog BNC connector.

• Ensure your TV is on the correct input channel.
Common terms of an input channel: INPUT, AV
CHANNEL, LINE1, LINE2, AUX.

• Ensure your DVR is properly connected to your
TV / Monitor

• Ensure connections are properly connected.

• Ensure the camera power supply is plugged in.

Picture is too bright • Ensure your camera isn’t pointed directly at a

source of light (e.g. sun or spot light).

• Move your camera to a different location.

Picture is too dark • Check the brightness and contrast settings of the

DVR or monitor

Night vision is not
working

• The night vision activates when light levels drop.
The area may have too much light.

Picture is not clear • Check the camera lens for dirt, dust,

spiderwebs. Clean the lens with a soft, clean
cloth.

• Make sure that the cable run is within the
limitations specified in the section ‘Cable
Extension Options’.

Bright spot in video
when viewing camera
at night

• Night vision reflects when pointing a camera
at a window. Move the camera to a different
location.

HDR/WDR is not
working

• Connect the camera to a Lorex MPX / HD DVR
using the MPX connector. HDR / WDR is not
supported on the analog output.

Picture is choppy • Turn off HDR / WDR mode. The camera’s frame

rate drops when HDR / WDR is turned on.

Troubleshooting

ATTENTION - This camera includes an Auto Mechanical IR Cut Filter. When

the camera changes between Day/Night viewing modes, an audible clicking
noise may be heard from the camera. This clicking is normal, and indicates
that the camera filter is working.

2. Connect the BNC connector to
the video input of a DVR.

3. Connect the camera to the
power adapter.

MPX / HD

Connect to an MPX / HD
DVR for 1080p viewing /
recording.

Analog

Connect to an analog DVR
for viewing / recording.

Analog

MPX

* Camera focus may be affected if the power connection is too
long. It is recommended not to extend the power connection past
200ft (61m).

Connect to a
12V DC AC power
supply.*

LEV2724_SERIES_TRIFOLDQSG_EN_R2

Adjusting Zoom & Focus

Analog Video Output

Hold the joystick on the camera cable / to zoom in
/ out. The camera will focus itself automatically.

MPX / HD Video Output

To adjust the zoom or focus of your camera, use the Zoom and
Focus controls in your DVR’s PTZ menu. See your DVR’s instruction
manual for more details.