Lorex LEV2712 SERIES Quick Start Manual

Resources

LEV2712_QSG_EN_R2

1080p HD Dome Security Camera

• 1080p HD Dome Security Camera

• Mounting Kit*

• BNC / Power Extension Cable*

• Power Adapter**

• Read this guide carefully and keep it for future reference.

• Follow all instructions for safe use of the product and handle with care.

• Use the camera within given temperature, humidity and voltage levels
noted in the camera’s specifications.

• Do not disassemble the camera.

• Do not point the camera directly towards the sun or a source of
intense light.

• Use only the supplied regulated power supply provided with the
product. Use of a non-regulated, non-conforming power supply can
damage the product and void the warranty.

• Periodic cleaning may be required. Use a damp cloth only. Do not use
any harsh, chemical-based cleaners.

• The supplied cable is rated for surface mounting only. Cables for in-wall
and floor-to-floor installations are sold separately (CMR type). These
and other cables are available at lorex.com

• Point the camera where there is the least amount of obstructions

(i.e., tree branches).

• Install the camera where vandals cannot easily reach.

• Secure cabling so that it is not exposed or easily cut.

• This camera is rated for outdoor use. Installation in a sheltered

location is recommended.

* Per camera in multi-camera packs.
** A multi-camera power adapter that provides power to multiple
cameras or individual power adapters may be provided depending on
product configuration.

Copyright © 2018 Lorex Corporation
As our products are subject to continuous improvement, Lorex reserves
the right to modify product design, specifications and prices, without
notice and without incurring any obligation. E&OE. All rights reserved.

• For a full list of compatible recorders, visit lorex.com/compatibility

• Not intended for submersion in water. Installation in a sheltered

location recommended.

• This camera includes an Auto Mechanical IR Cut Filter. When the

camera changes between Day/Night viewing modes, an audible clicking
noise may be heard from the camera. This clicking is normal, and
indicates that the camera filter is working.

Quick Start Guide

English Version 2.0

LEV2712 SERIES

Package Contents

ATTENTION:

A REGULATED UL / CSA APPROVED power supply is REQUIRED for use
with this camera (included). Use of a non-regulated, non-conforming
power supply can damage this product and voids the warranty.

Safety Precautions

Installation Tips

Disclaimers

Need Help?

Visit us online for up-to-date software and

complete instruction manuals

Click on the Downloads tab

4

Visit lorex.com

Search for the model number

of your product

Click on your product in the

search results

3

2

1

www.lorex.com

3.7” /

94mm

Dimensions

3.9” /

98mm

Connecting the Cameras

Individual Power Adapter* Multi-Camera Power Adapter*

Connecting the Cameras

* Images for representation only

Mounting Surface

Camera Base

Ball Camera

Adjustment Ring

Dome Cover

Drywall Anchors (×4)

Mounting Screws (×4)

To install your camera:

Installing the Camera

Extend the cable run for your camera depending on the cable type used.
Additional extension cables sold separately. See table below:

Connect the male power head
and the BNC connector to the
camera.

Connect the BNC connector
to a video input on your DVR.

Connecting the Camera

Cable Notch

LEV2712_QSG_EN_R2

Power Adapter Types

A multi-camera power adapter that provides power to multiple cameras
or individual power adapters may be provided, depending on product
configuration.

Problem Solution

No picture / signal • The cameras are only compatible with

certain Lorex HD DVRs. For the full list of
compatible recorders, visit

lorex.com/compatibility

• Ensure your TV or monitor is on the correct
input channel. Common terms for input
channels: INPUT, AV CHANNEL, LINE1,
LINE2, AUX.

• Ensure your DVR is properly connected to
your TV or monitor.

• Ensure connections are properly connected.

• Ensure the camera power supply is plugged
in.

Picture is too bright • Ensure your camera isn’t pointed directly at

a source of light (e.g., sun or spot light).

• Check the brightness settings of the DVR
and monitor.

• Move your camera to a different location.

Picture is too dark • Check the brightness and contrast settings

of the DVR and monitor.

Night vision is not
working

• The night vision activates when light levels
drop. The area may have too much light.

Picture is not clear • Check the camera lens for dirt, dust,

spiderwebs. Clean the lens with a soft,
clean cloth.

• Make sure that the cable run is within the
limitations specified in the section ‘Cable
Extension Options’.

• Remove the vinyl film from the camera lens
when your installation is complete.

Bright spot in video when
viewing camera at night

• Night vision reflects when pointing a
camera through a window. Move the camera
to a different location.

Troubleshooting

ATTENTION:

Test your camera prior to selecting a permanent mounting location by temporarily
connecting the camera and cable to your DVR.

Before Installing the Camera

• Decide whether to run the cables through the
wall / ceiling (drilling required) or along the wall
/ ceiling.

• If you run the cables along the wall / ceiling,
you must run the cable through the cable
notch on the base. This will keep the camera
base flush to the surface when mounted.

Connect the female power
head to the included power
adapter.

Camera

DVR

Male Power Female Power

Setup Diagram

BNC Video

12V DC Power

Camera

Extension Cable

Power Adapter

HD DVR

Cable Extension Options

Option Cable Type

Max Cable Run

Distance

1

Lorex model MCBL-60BNCU BNC Cable
(included with camera)

60ft (18m)

2

‘RG59’ or ‘Coax’ or ‘Coaxial BNC’ Siamese
(Video and Power)

300ft (91m)

3

‘RG59’ or ‘Coax’ or ‘Coaxial BNC’ (Video
Only)

2

800ft (242m)

Notes:

1. The extension cable must be a single stretch of cable between the
DVR and camera. You cannot connect multiple extension cables to
each other.

2. For cable runs above 300ft (91m), you must connect the power
adapter directly to the camera, rather than at the end of the
extension cable.

3. Indicators that your cable run may be too long:

• Video is permanently black & white (even during day time).

• Video is unclear, soft, or distorted.

4. For more information on extension cables, visit lorex.com.

1. Rotate the camera base counterclockwise to separate it
from the ball camera, adjustment ring, and dome cover.

2. Use the included mounting template to mark and drill holes
for the included mounting screws.

3. Feed the cable through the camera base. If you are running
the cables against a wall or ceiling, make sure to pass the
cable through the cable notch as shown above.

4. Connect the cables as shown in the section ‘Connecting the
Camera’.

5. Mount the camera base to the mounting surface using the
included screws and optional drywall anchors.

6. Place the adjustment ring over the dome cover, then place
both over the ball camera. Twist the adjustment ring
clockwise halfway onto the camera base. Do not tighten all
the way.

7. Move the ball camera to the desired position. While holding
the ball camera firmly in place, twist the adjustment ring
the rest of the way to secure it to the camera base. Holding
the camera prevents it from moving while securing the
adjustment ring.

8. Remove the vinyl film from the camera lens when your
installation is complete.