Lorex LEV1512 SERIES Quick Start Manual

Contents
• Weatherproof HD dome camera*
• Mounting kit*
• 60ft/18m UL-rated BNC / power extension cable*
• Power adapter**
Copyright © 2016 Lorex Corporation As our products are subject to continuous improvement, Lorex Corporation reserves the right to modify product design, specifications and prices, without notice and without incurring any obligation. E&OE LEV1512_SERIES_TRIFOLDQSG_EN_R1
ATTENTION - A REGULATED UL / CSA APPROVED
12V DC power supply is REQUIRED for use with this camera. Use of a non-regulated, non-conforming power supply can damage this product and voids the warranty.
Warning/Caution
• Read this guide carefully and keep it for future reference
• Follow all instructions for safe use of the product and handle with care
• Use the camera within given temperature, humidity and voltage levels noted in Camera Specifications
• Do not disassemble the camera
• Do not point the camera directly towards the sun or a source of intense light
• Periodic cleaning may be required. Use a damp cloth only. Do not use harsh cleaners or aerosol cleaners
• Cables for in-wall / floor-to-floor installations are sold separately
Installation Tips
• Point the camera where there is the least amount of obstructions (i.e. tree branches)
• Install the camera in a location that is difficult for vandals to reach
• Secure cabling so that it is not exposed or easily cut
• Camera rated for outdoor use. Installation in a sheltered location recommended
MPX HD WEATHERPROOF
NIGHT VISION SECURITY CAMERA
Quick Start Guide
English Version 1.0
Dimensions
* Per camera in multi-camera packs. ** A multi-camera power adapter or individual power adapters may be provided, depending on product configuration.
3.7” / 93mm
2.9” / 74mm
Resources
Vist www.lorextechnology.com
Search the model number of your product
Click on your product in the search results
1
2
3
4
Click the Downloads tab
Need Help?
Visit us online for up-to-date software and complete
instruction manuals
LEV1512 SERIES
Setup Diagram
To Camera:
To DVR:
Male Power
BNC
1. Connect the BNC and power connectors to the camera.
Female Power
2. Connect the BNC connector to the video input of your DVR.
3. Connect the power connectors to the power adapter.
Connecting the Camera
MPX DVR
Power Adapter Types
Individual Power Adapter
Multi-Camera Power Adapter
A multi-camera power adapter that provides power to multiple cameras or individual power adapters may be provided, depending on product configuration.
Cable notch
Before installing the camera:
• Decide whether to run the cables through the wall / ceiling (drilling required) or along the wall / ceiling.
• If you run the cables along the wall / ceiling, you must run the cable through the cable notch on the base. This will keep the camera base flush to the wall / ceiling when mounted.
To install the camera:
1. Rotate the camera base counterclockwise to separate it from the ball camera and dome cover.
Installing the Camera
ATTENTION - Ensure the camera is working correctly prior to
permanent installation by temporarily connecting the camera(s) and cable(s) to the DVR.
ATTENTION - This camera includes an Auto Mechanical IR Cut Filter.
When the camera changes between Day/Night viewing modes, an audible clicking noise may be heard from the camera. This clicking is normal, and indicates that the camera filter is working.
2. Use the included mounting template to mark and drill holes for the included mounting screws.
3. Feed the cable through the camera base. If you are running the cables against a wall or ceiling, make sure to pass the cable through the cable notch as shown above.
4. Connect the cables as shown in the section ‘Connecting the Camera’.
5. Mount the camera base to the mounting surface using the included screws and drywall anchors (optional)
6. Place the adjustment ring over the dome cover, then place both over the ball camera. Twist the adjustment ring clockwise halfway onto the camera base. Do not tighten all the way.
7. Move the ball camera to the desired position. While holding the ball camera firmly in place, twist the adjustment ring the rest of the way to secure it to the camera base. Holding the camera prevents it from moving while securing the adjustment ring.
Installation Diagram
Mounting Surface
Ball Camera
Dome Cover
Camera Base
LEV1512_SERIES_TRIFOLDQSG_EN_R1
Cable Extension Options
Extend the cable run for your camera depending on the cable type used. Additional extension cables sold separately. See table below:
Option Cable Type Max Cable Run
Distance
1 Lorex model MCBL-60BNCU / MCBL-
60BNCU2 BNC Cable
60ft / 18m
2 ‘RG59’ or ‘Coax’ or ‘Coaxial BNC’
Siamese (Video and Power)
300ft / 92m
3 ‘RG59’ or ‘Coax’ or ‘Coaxial BNC’
(Video Only)
2
800ft / 242m
Notes:
1. The extension cable must be a single stretch of cable between the DVR and camera. You cannot connect multiple extension cables to each other.
2. For cable runs above 300ft / 92m (option 3), you must connect the power adapter directly to the camera, rather than at the end of the extension cable.
3. Indicators that your cable run may be too long:
• Video is permanently black & white (even during day time)
• Video is unclear, soft, or distorted
4. For more information on extension cables, visit
www.lorextechnology.com.
Problem Solution
No picture / signal • Ensure the camera is connected to an MPX
Series DVR. Camera is not compatible with other DVR models. Visit www.lorextechnology.
com for compatibility information.
• Ensure your TV is on the correct input channel. Common terms of an input channel: INPUT, AV CHANNEL, LINE1, LINE2, AUX.
• Ensure your DVR is properly connected to your TV / Monitor.
• Ensure connections are properly connected.
• Ensure the camera power supply is plugged in.
Picture is too bright • Ensure your camera isn’t pointed directly at a
source of light (e.g. sun or spot light).
• Move your camera to a different location.
Picture is too dark • Check the brightness and contrast settings of
the DVR or monitor.
Night vision is not working
• The night vision activates when light levels drop. The area may have too much light.
Picture is not clear • Check the camera lens for dirt, dust,
spiderwebs. Clean the lens with a soft, clean cloth.
• Make sure that the cable run is within the limitations specified in the section ‘Cable Extension Options’.
Bright spot in video when viewing camera at night
• Night vision reflects when pointing a camera at a window. Move the camera to a different location.
Troubleshooting
Loading...