Assembly Instruction Sheet
ToolsRequired: Flatheadscrewdriver,Phillipsscrewdriver, pliers,wirecutters, wire strippers,electricaltape,
safetyglasses.
BulbRecommended:
EstimatedAssembly Time:
Preparation:
belowtobe sure allpartsare present. Ifanyparts are missingordamaged, do notattemptto assemble, install,or
operatethefixture. Contact customerservicefor replacement parts.
Identifyandinspect all partsbeforebeginning installation. Checkpackagecontent list anddiagrams
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
(1)MediumBase 100W bulbMaximum,Alternate bulb(1)23W CFLMaximum.
20-30minutes
Package Contents
Socket
D
Assembly
x1
Ceiling
A
C
B
12” Rod
x2
Canopy
x1
6” Rod
x2
Upper Collar
E
x1
F
Steel Collar
G
x1
Socket Collar
H
x1
Shade
x1
Hardware Contents
Crossbar Assembly
STEP 1 Assemble the Rods and the Ceiling Canopy-
A. Determine the Rods (B/C) to be assembled to the Socket Assembly
(D) according to your hanging height.
B. Pass the supply wires and ground wire through the chosen rods
(B/C) and the Ceiling Canopy (A). Thread the Socket Assembly (D),
the chosen Rods (B/C) and the Ceiling Canopy (A) together. Hand
tighten until snug.
AA
x1
Thank you for purchasingaproduct.
Need assistance with partsorassembly?Callour customerservice
Figure 1
B
B
Supply Wires
and Ground Wire
D
STEP 2 Install Crossbar Assembly-
A. Pass the supply wires through the
Crossbar Assembly (AA). Attach the
Crossbar Assembly (AA) to the Outlet
Box with the head of the Green
Ground Screw facing you. Secure it
with Outlet Box Screws (not included).
Tighten until snug.
Outlet Box Screws
(not included)
STEP 3 Fit Ceiling Canopy to
A.
not, adjust the length of the nipple on the CrossbarAssembly (AA) by
-
Crossbar Assembly
Remove mounting balls from the
Crossbar Assembly (AA). Fit the
Ceiling Canopy A to the
Crossbar Assembly (AA) and
secure with mounting balls.
Note: The ( )
should be snug against the
and the mounting balls. If
ceiling
unscrewing the preassembled hex nut and lock washer and then
screwing the mounting screws in or out of the crossbar until the
correct length is achieved. Once the ( ) is secure,
remove the mounting ball and ( ) and proceed to
Step 4.
()
Ceiling Canopy A
Ceiling Canopy A
A
Figure 2
A
Mounting Ball
Ceiling Canopy A
C
C
Outlet
Box
AA
Supply Wires
with Ground Wire
Figure 3
AA
Hex Nut and
Lock Washer
Mounting Screw
1of2
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.
B. Connect White Supply Wire from the Outlet Box to Ribbed side Wire
from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth
side Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground Wire from
fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
Ribbed side wire
from fixture
Smooth side wire
from fixture
Ground wire
from fixture
Figure 4
STEP 5 Install Fixture Body-
A. Carefully tuck all wires into the outlet
box and position the Ceiling Canopy
(A) over the outlet box.Align the
holes in the Ceiling Canopy (A) with
C
AA
Mounting
Screw
the mounting screws, then attach the
Ceiling Canopy (A) using the
previously removed mounting balls.
Hand tighten until snug.
Figure 5
Mounting Ball
STEP 6 Install Shade-
A. Place the Upper Collar (E), the Shade (F)
and the Steel Collar (G) onto the Socket
Assembly (D) in turn and secure with the
Socket Collar (H). Hand tighten until snug.
STEP 7 Install Bulb-
A. This fixture uses standard bulb with
medium base. Maximum 100 watts.
B. Insert bulb and screw snugly into place.
Your fixture is now assembled and ready
to use. Enjoy!
Figure 6
D
E
F
G
H
Figure 7
Bulb
FINISH: BRUSHED NICKEL
PALLADIAN BRONZE
WEATHERED BRASS
IMPERIAL SILVER
Base
1
2
4
1
2
4
Medium
Bulb
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART
METALSHADE
6” ROD
12” ROD
RETAINE R RING
METALSHADE
6” ROD
12” ROD
RETAINER RING
(1) 100W
(Not Supplied)
NO.
3
3
2
3
4
1
REQ.
1
2
2
1
1
2
2
1
NO.
.
1
2
3
4
1
2
3
4
REPLACEMENT PART
METALSHADE
6” ROD
12” ROD
SHADE
6” ROD
12” ROD
RETAINER RING
Thank you for purchasingaproduct.
Need assistance with partsorassembly?Call ourcustomer service
5” Dia.
3.5”
48”
OVERALL HEIGHT INCLUDES
(2)6” AND (2)12” RODS
9”
8” Dia.
REQ.
1
2
2
1
2
2
1
2of2
Loading...