Loctite 98032, Hysol 050-Gas Operation Manuals

OPERATION MANUAL

EQUIPMENT

P/N 98032



Loctite is a trad

emark of Loctite Corporation, U.S.A.

Data in the manual is subject to change without notice.

 Copyright 2001. Loctite Corporation. All rights reserved. 985250 06/01

Loctite Brazil

Av. Prof. Vernon Krieble, 91
06690-11-Itapevi

São Paulo-Brazil

Loctite Americas

1001 Trout Brook Crossing

Rocky Hill, CT 06067-3910

Loctite Canada Inc.

2225 Meadowpine Boulevard

Mississauga, Ontario L5N 7P2

Loctite Company de México, S.A.d e C.V.

Calzada de la Viga s/n, Fracc. Los Laureles
Loc. Tulpetlac, C.P. 55090
Ecatepac de Morelos, Edo. de México,

México

www.loctite.com

A Company

Hysol 050

-

Gas

®

Please Observe the Following

Safety

Do not touch the nozzle, the exhaust ports, or molten adhesive with bare skin as they are hot ­the operating temperature of the Loctite® Hysol® 050-Gas is approximately 392°F (200ºC).
Protective gloves should always be worn. Careless handling can cause skin burns. If molten

adhesive comes into contact with the skin immerse the affected area immediately in plenty of cold
water. Seek medical advice if necessary.
In addition to the safety instructions herein, any statutory regulations, local fire insurance regulations,
or other generally valid “regulations for accident prevention” must be complied with when using this
tool.

• Never use the tool if it is damaged in any way.

• Do not use this tool in the vicinity of any heat-sensitive materials, or any flammable materials,

liquids, or gases.

• When refilling, ensure that you switch off the tool before commencing, and that you keep away
from sources of ignition.

• Ensure that the tool is held away from your face and body while igniting the gas.

• Always use the foldaway stand provided when resting the tool. Do not leave the tool on its side,

as molten adhesive may flow back into the melt chamber, clogging the feed system.

• Do not leave the tool unattended while switched on.

• Do not expose to heat above 120°F (50°C), and avoid prolonged exposure to the sun.

• Do not try to open, puncture, or incinerate the gas tank.

BOND SEAL ASSEMBLE INSULATE REINFORCE ENCAPSULATE REPAIR FILL – INSTANTLY

Suitable for use with most materials. Just apply Loctite® Hysol® hotmelt to one surface then press
parts together and the bond is made. Can be used for bonding: Wood, Paper, Cardboard, Foam,
Chipboard, Hardboard, some Plastics, Rubber, Glass, thin Metals, Ceramics, Leather, Fabrics and
many more.
The Loctite® Hysol® 050-Gas is simplicity itself. To operate just turn on the gas, press the ignition
switch, and the gun will be ready for use in approximately 5 minutes. Glue sticks can be fed
continuously through the back of the gun. Use only genuine Loctite® Hysol® adhesive sticks

Items supplied

Hot Melt Stick Dispenser
Manual

Technical Data

Dimensions (L x H x W): 13 ¾” x 10 ½” x 3”

(approx. 350 x 270 x 75 mm)
Total weight: 1.6 lbs. (approx. 750 g)
Heating up time: 4 - 7 min.
Operating temperature: approx. 392°F (200°C)
Diameter of adhesive inlet: 1/2" (12 mm)
(Use only genuine Loctite

®

Hysol® adhesive sticks)